VJ3640Y225KXBAT

End of Life March-2018 – Alternative Device: VJ Source Energy Capacitor (SEC) VJ Controlled Discharge Capacitor (CDC) www.vishay.com Vishay Vitramon Surface Mount Multilayer Ceramic Chip Capacitors with Integrated Resistor for High Pulse Current Applications FEATURES • Integrated resistor on the surface of the capacitor • Low electrostrictive ceramic formulation for repeated charge and discharge cycles Available Available • High pulse discharge currents • Excellent reliability and high voltage performance • Available with tin / lead barrier termination (code “L”) • Wet built process • Reliable Noble Metal Electrode (NME) system • Made with a combination of design, materials and tight process control to achieve very high field reliability • Resistor glass overglaze contains lead • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 Note * This datasheet provides information about parts that are RoHS-compliant and / or parts that are non RoHS-compliant. For example, parts with lead (Pb) terminations are not RoHS-compliant. Please see the information / tables in this datasheet for details APPLICATIONS • Detonation devices (munitions, pyrotechnic, blasting) • Down hole drilling • Electronic fuzing ELECTRICAL SPECIFICATIONS Note • Electrical characteristics at +25 °C unless otherwise specified Operating Temperature: -55 °C to +125 °C Aging Rate: 1 % maximum per decade Capacitance Range: 33 nF to 560 nF Insulation Resistance (IR):  at +25 °C without resistor: 100 000 M minimum or 1000 F, whichever is less. at +125 °C without resistor: 10 000 M minimum or 100 F, whichever is less. Voltage Range: 1000 VDC to 1500 VDC Temperature Coefficient of Capacitance (TCC):  X5P: ± 10 % from -55 °C to +85 °C, with 0 VDC applied X7R: ± 15 % from -55 °C to +125 °C, with 0 VDC applied Parallel Resistor: 500 M ± 30 % Dissipation Factor (DF):  2.5 % maximum at 1.0 VRMS and 1 kHz Revision: 09-Jan-18 Dielectric Strength Test: performed per method 103 of EIA 198-2-E.  Applied test voltages:  1000 VDC / 1500 VDC-rated: 120 % of rated voltage Document Number: 45203 1 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 End of Life March-2018 – Alternative Device: VJ Source Energy Capacitor (SEC) VJ Controlled Discharge Capacitor (CDC) www.vishay.com Vishay Vitramon QUICK REFERENCE DATA DIELECTRIC CAPACITANCE CASE MAXIMUM VOLTAGE (V) MINIMUM MAXIMUM 3040 1500 33 nF 220 nF 3640 1500 47 nF 330 nF 4044 1500 100 nF 560 nF X7R (X5P) Note • Detail ratings see “Selection Chart” ORDERING INFORMATION VJ3640 (3) Y 184 CASE CODE DIELECTRIC CAPACITANCE NOMINAL CODE 3040 3640 4044 Y = X7R (X5P) Expressed in picofarads (pF). The first two digits are significant, the third is a multiplier. Examples: 184 = 180 nF 334 = 330 nF K X R A CAPACITANCE TERMINATION DC VOLTAGE TOLERANCE RATING (1) J=±5% K = ± 10 % M = ± 20 % X = Ni barrier 100 % tin plate matte finish L = Ni barrier with tin lead plated finish min. 4 % lead G = 1000 V R = 1500 V T 8R (2) MARKING PACKAGING PROCESS CODE A = unmarked T = 7" reel / plastic tape Notes (1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance Consult for questions: mlcc@vishay.com (2) Process Code must be added to control special requirements (3) Size designator may be replaced by four digit drawing number used to control non-standard products and / or special requirements DIMENSIONS in inches [millimeters] W L T MAX. P TERMINATION (P) PART ORDERING NUMBER LENGTH (L) WIDTH (W) MAXIMUM THICKNESS (T) MINIMUM MAXIMUM 3040 VJ3040 0.300 ± 0.015 [7.62 ± 0.38] 0.400 ± 0.015 [10.20 ± 0.38] 0.100 [2.54] 0.010 [0.25] 0.030 [0.76] 3640 VJ3640 0.360 ± 0.015 [9.14 ± 0.38] 0.400 ± 0.015 [10.20 ± 0.38] 0.010 [0.25] 0.030 [0.76] 4044 VJ4044 0.400 ± 0.015 [10.16 ± 0.38] 0.440 ± 0.015 [11.17 ± 0.38] 0.020 [0.50] 0.040 [1.00] CASE CODE 0.120 [3.05] 0130 (1) [3.30] 0.120 [3.05] Note Thickness used for 3640 - 1500 V - 220 nF and 270 nF (1) Revision: 09-Jan-18 Document Number: 45203 2 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 End of Life March-2018 – Alternative Device: VJ Source Energy Capacitor (SEC) VJ Controlled Discharge Capacitor (CDC) www.vishay.com Vishay Vitramon SELECTION CHART DIELECTRIC X7R (X5P) VJ3040 (1) STYLE CASE CODE VJ3640 (1) 3040 VJ4044 (1) 3640 4044 VOLTAGE (VDC) 1000 1500 1000 1500 1000 1500 VOLTAGE CODE G R G R G R CAP. CODE CAP. 223 0.022 μF 273 0.027 μF 333 0.033 μF • 393 0.039 μF • 473 0.047 μF • • 563 0.056 μF • • • 683 0.068 μF • • • 823 0.082 μF • • 104 0.10 μF • • • • 124 0.12 μF • • • • 154 0.15 μF • • • • • 184 0.18 μF • • • • • 224 0.22 μF • • • • • 274 0.27 μF • • • • 334 0.33 μF • • • 394 0.39 μF • 474 0.47 μF • 564 0.56 μF • 684 0.68 μF 824 0.82 μF 105 1.0 μF 125 1.2 μF 155 1.5 μF 185 1.8 μF 225 2.2 μF 275 2.7 μF 335 3.3 μF • • • Notes RoHS-compliant except when supplied with lead (Pb)-containing termination, code “L” • Plastic tape (1) See soldering recommendations within this data book, or visit www.vishay.com/doc?45034 CONSTRUCTION Surface mount multilayer ceramic chip capacitor Over glaze: Resistor passivation to protect against contamination and increase electrical stability Resistor: Thick film print Revision: 09-Jan-18 Document Number: 45203 3 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 End of Life March-2018 – Alternative Device: VJ Source Energy Capacitor (SEC) VJ Controlled Discharge Capacitor (CDC) www.vishay.com Vishay Vitramon TYPICAL PARAMETERS TEMPERATURE COEFFICIENT OF CAPACITANCE 20 0 15 -10 CAPACITANCE (%) 10 4044, 330 nF, 1500 V -20 -30 -40 3640, 180 nF, 1500 V -50 -60 X7R: ± 15 % from -55 °C to +125 °C 3640, 180 nF, 1500 V 10 5 0 -5 TCC also meets X5P ± 10 % from -55 °C to +85 °C -10 -70 -15 -80 -20 -75 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (°C) 0 250 500 750 1000 1250 APPLIED VOLTAGE (VDC) 1500 DISCHARGE PULSE OF 4044 CDC Peak current: > 1700 Ap Rise time 79 ns 4044, 330 nF, 1500 V DISCHARGE CURRENT VS. CHARGE VOLTAGE PULSE DISCHARGE CURRENT (A) CAPACITANCE (%) VOLTAGE COEFFICIENT OF CAPACITANCE 2000 Above 1200 V, excessive dV/dt 1800 may cause failure 4044, 330 nF 1600 1400 3640, 274 nF 1200 3640, 180 nF 1000 800 600 900 % DISSIPATION FACTOR 0.035 4044, 330 nF, 1500 V 0.030 0.025 0.020 0.015 0.010 0.005 3640, 180 nF, 1500 V 0.000 -55 -35 -15 Revision: 09-Jan-18 -5 25 45 65 85 105 125 TEMPERATURE (°C) 1500 SELF DISCHARGE VS. TIME DISCHARGE VOLTAGE (VDC) DISSIPATION FACTOR VS. TEMPERATURE 0.040 1000 1100 1200 1300 1400 CHARGE VOLTAGE (VDC) 1400 Capacitor (no resistor) 1200 1000 800 Vc = Vo x ε-t/rc 600 400 CDC, 500 MΩ resistor 200 0 0 100 200 300 400 500 600 700 800 900 TIME (s) Document Number: 45203 4 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 End of Life March-2018 – Alternative Device: VJ Source Energy Capacitor (SEC) VJ Controlled Discharge Capacitor (CDC) www.vishay.com Vishay Vitramon STANDARD PACKAGING QUANTITIES (1)(2)(3) 7" REEL QUANTITIES CASE CODE TAPE SIZE PLASTIC TAPE PACKAGING CODE “T” 3040 16 mm 500 3640 16 mm 350 4044 24 mm 300 Notes (1) Vishay Vitramon uses embossed plastic carrier tape (2) REFERENCE: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement” (3) n/a = not available STORAGE AND HANDLING CONDITIONS (1) Store the components at 5 °C to +40 °C ambient temperature and  70 % related humidity conditions. (2) The product is recommended to be used within a time-frame of 2 years after shipment.  Check solderability in case extended shelf life beyond the expiry date is needed. Precautions: a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering. b. Store products on the shelf and avoid exposure to moisture or dust. c. Do not expose products to excessive shock, vibration, direct sunlight and so on. Revision: 09-Jan-18 Document Number: 45203 5 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer  ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000