VO610A-3X019T

VO610A www.vishay.com Vishay Semiconductors Optocoupler, Low Input Current, Phototransistor Output FEATURES A 1 4 E C 2 3 C • Temperature range - 55 °C to + 110 °C • Rated impulse voltage (transient overvoltage) VIOTM = 6 kVpeak • Isolation test voltage (partial discharge test voltage) Vpd = 1.6 kV • Rated isolation voltage (RMS includes DC) VIOWM = 600 VRMS • Rated recurring peak voltage (repetitive) VIORM = 850 Vpeak • Thickness through insulation  0.4 mm • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS 17918_10 Circuits for safe protective separation against electrical shock according to safety class II (reinforced isolation): • for appl. class I - IV at mains voltage  300 V • for appl. class I - IV at mains voltage  600 V according to table 1 of IEC 60664-1, suitable for: - Switch-mode power supplies - Line receiver - Computer peripheral interface - Microprocessor system interface       DESCRIPTION The VO610A consists of a phototransistor optically coupled to a gallium arsenide infrared-emitting diode in a 4 pin plastic dual inline package. AGENCY APPROVALS (All parts are certified under base model VO610A) • BSI: EN 60065:2002, EN 60950:2000 • DIN EN 60747-5-5, available with option 1 • FIMKO EN 60065, EN 60335-1, EN 60950-1 • UL file no. E52744 • cUL tested to CSA 22.2 bulletin 5A • CQC GB4943.1-2011, GB8898-2011 ORDERING INFORMATION DIP-# V O 6 1 0 A - # X 0 # # T 7.62 mm PART NUMBER CTR BIN PACKAGE OPTION TAPE AND REEL Option 6 10.16 mm AGENCY CERTIFIED/PACKAGE BSI, FIMKO, UL, cUL DIP-4 SMD-4, option 7 SMD-4, option 8 SMD-4, option 9 VDE, BSI, FIMKO, UL, cUL DIP-4 DIP-4, 400 mil, option 6 SMD-4, option 7 SMD-4, option 8 SMD-4, option 9 Option 7 > 0.6 mm Option 8 Option 9 9.27 mm > 8 mm CTR (%) 40 to 80 VO610A-1 40 to 80 VO610A-1X019T 63 to 125 VO610A-2 63 to 125 - 100 to 200 VO610A-3 VO610A-3X007T VO610A-3X008T VO610A-3X009T 100 to 200 VO610A-3X001 VO610A-3X016 VO610A-3X018T VO610A-3X019T 160 to 320 VO610A-4X008T 160 to 320 VO610A-4X017T VO610A-4X019T Note • Additional options may be possible, please contact sales office Rev. 1.7, 18-Feb-13 Document Number: 81775 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VO610A www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage VR 6 V Forward current IF 60 mA Forward surge current tp  10 μs IFSM 1.5 A LED power dissipation at 25 °C Pdiss 100 mW Collector emitter voltage VCEO 70 V Emitter collector voltage VECO 7 V IC 50 mA tp/T = 0.5, tp  10 ms ICM 100 mA at 25 °C Pdiss 150 mW OUTPUT Collector current Collector peak current Output power dissipation COUPLER Isolation test voltage (RMS) VISO 5000 VRMS Operating ambient temperature range Tamb - 55 to + 110 °C Storage temperature range Tstg - 55 to + 125 °C Tsld 260 °C Soldering temperature (1) t = 1 min 2 mm from case,  10 s Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted parts (SMD), and wave profile for soldering conditions for through hole parts (DIP), please go to “Assembly Instructions” (www.vishay.com/doc?80054). ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. Forward voltage IF = 50 mA VF Reverse current VR = 6 V IR VR = 0, f = 1 MHz Cj IC = 1 mA VCEO 70 7 TYP. MAX. UNIT INPUT Junction capacitance 1.25 1.6 V 100 μA 50 pF OUTPUT Collector emitter voltage Emitter collector voltage V IE = 100 μA VECO VCE = 20 V, IF = 0 A ICEO Collector emitter saturation voltage IF = 10 mA, IC = 1 mA VCEsat Cut-off frequency VCE = 5 V, IF = 10 mA, RL = 100  fc 110 kHz f = 1 MHz Ck 0.6 pF Collector emitter cut-off current V 10 100 nA 0.3 V COUPLER Coupling capacitance Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Rev. 1.7, 18-Feb-13 Document Number: 81775 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VO610A www.vishay.com Vishay Semiconductors CURRENT TRANSFER RATIO (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION VCE = 5 V, IF = 1 mA IC/IF VCE = 5 V, IF = 10 mA PART SYMBOL MIN. TYP. VO610A-1 CTR 13 30 MAX. UNIT % VO610A-2 CTR 22 45 % VO610A-3 CTR 34 70 % VO610A-4 CTR 56 90 VO610A-1 CTR 40 80 % VO610A-2 CTR 63 125 % VO610A-3 CTR 100 200 % VO610A-4 CTR 160 320 % % SAFETY AND INSULATION RATED PARAMETERS PARAMETER TEST CONDITION SYMBOL MIN. Partial discharge test voltage - routine test 100 %, ttest = 1 s Vpd 1.6 kV Partial discharge test voltage - lot test (sample test) tTr = 60 s, ttest = 10 s, (see figure 2) Vpd 1.3 kV Insulation resistance TYP. UNIT VIO = 500 V RIO 1012  VIO = 500 V, Tamb = 100 °C RIO 1011  VIO = 500 V, Tamb = 150 °C (construction test only) RIO 109  Recurring peak voltage VIORM Rated impulse voltage VIOTM Max. working voltages MAX. Forward current 6 kV 850 Vpeak ISI 130 mA Power dissipation PSO 265 mW Safety temperature Tsi 150 °C Creepage distance 7.6 mm Note • According to DIN EN 60747-5-5 (VDE 0884), § 7.4.3.8.2 (see figure 2). This optocoupler is suitable for safe electrical isolation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits. VIOTM 300 t1, t2 t3 , t4 ttest tstres Phototransistor Pso (mW) 250 200 = 1 s to 10 s =1s = 10 s = 12 s Vpd 150 VIOWM VIORM 100 IR-diode Isi (mA) 50 0 0 0 94 9182-2 25 50 75 100 Tsi - Safety Temperature (°C) Fig. 1 - Derating Diagram Rev. 1.7, 18-Feb-13 125 150 13930 t3 ttest t4 t1 tTr = 60 s t2 t stres t Fig. 2 - Test Pulse Diagram for Sample Test according to DIN EN 60747-5-5 (VDE0884), IEC 60747 Document Number: 81775 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VO610A www.vishay.com Vishay Semiconductors SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL Delay time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 3) MIN. TYP. MAX. UNIT td 3 μs Rise time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 3) tr 3 μs Fall time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 3) tf 4.7 μs Storage time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 3) ts 0.3 μs Turn-on time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 3) ton 6 μs Turn-off time VS = 5 V, IC = 2 mA, RL = 100 , (see figure 3) toff 5 μs Turn-on time VS = 5 V, IF = 10 mA, RL = 1 k, (see figure 4) ton 9 μs Turn-off time VS = 5 V, IF = 10 mA, RL = 1 k, (see figure 4) toff 10 μs IF IF 0 +5V IF 0 I C = 2 mA; adjusted through input amplitude tp IC t 100 % 90 % R G = 50 Ω tp = 0.01 T t p = 50 µs 10 % 0 Channel I Channel II 50 Ω 100 Ω td Fig. 3 - Test Circuit, Non-Saturated Operation ts t on tp td tr t on (= td + tr) 95 10804 IF tr Oscilloscope R L = 1 MΩ C L = 20 pF Pulse duration Delay time Rise time Turn-on time tf t off ts tf t off (= ts + tf) t Storage time Fall time Turn-off time 96 11698 Fig. 5 - Switching Times +5V I F = 10 mA 0 IC R G = 50 Ω tp = 0.01 T t p = 50 µs Channel I Channel II 50 Ω Oscilloscope R L ≥ 1 MΩ C L ≤ 20 pF 1 kΩ 95 10843 Fig. 4 - Test Circuit, Saturated Operation Rev. 1.7, 18-Feb-13 Document Number: 81775 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VO610A www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 6.5 ± 0.3 Pin 1 identifier 7.62 to 9.5 4.58 ± 0.3 7.62 typ. 0.4 ± 0.1 3.5 ± 0.3 4.5 ± 0.3 2.8 ± 0.5 0° to 15° 1.3 ± 0.1 0.25 typ. 0.5 ± 0.1 2.54 typ. i178027-11 Option 6 Option 7 Option 8 Option 9 7.62 typ. 7.62 typ. 7.62 typ. 10.3 max. 7.62 typ. 3.5 ± 0.3 0.6 min. 0.25 ± 0.1 4.3 ± 0.3 3.5 ± 0.3 0.1 ± 0.1 3.6 ± 0.3 0.1 min. 8 min. 2.7 min. 9.27 min. 0.6 min. 10.3 max. 0.6 min. 12.1 max. 8 min. 0.76 R 0.25 2.54 0.76 2.54 0.76 2.54 10.16 typ. R 0.25 R 0.25 9.95 min. 1.52 13.0 1.52 7.7 11.05 1.78 8 min. 11.05 1.78 1.52 1.78 20802-38 PACKAGE MARKING (Example of VO617A-3X018T) VO610A-3 V YWW 24 Note • Only options 1, 7, and 8 are reflected in the package marking. • The VDE logo is only printed on option 1 parts. • Tape and reel suffix (T) is not part of the package marking. Rev. 1.7, 18-Feb-13 Document Number: 81775 5 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VO610A www.vishay.com Vishay Semiconductors PACKING INFORMATION DEVICE PER TUBE TYPE UNITS/TUBE TUBES/BOX UNITS/BOX 100 40 4000 DIP-4, standard and option 6 Top cover tape Embossed carrier Embossment 17998 Fig. 6 - Tape and Reel Shipping Medium 10 pitch cumulative tolerance on tape ± 0.2 2 ± 0.1 1.55 + 0.1 4 ± 0.1 0.35 ± 0.1 1.75 ± 0.1 7.5 ± 0.1 16 ± 0.3 4.65 ± 0.1 5° max. X 5° max. 12 ± 0.1 4.55 ± 0.1 X 1.5 ± 0.1 10.3 ± 0.1 Section X-X Fig. 7 - Tape and Reel Packing for Option 7 and Option 9 (1000 units per reel) Rev. 1.7, 18-Feb-13 Document Number: 81775 6 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VO610A www.vishay.com Vishay Semiconductors 1.5 ± 0.1 4 ± 0.1 2 ± 0.1 1.75 ± 0.1 0.35 ± 0.1 11.5 ± 0.1 24 ± 0.3 12.5 ± 0.1 X 5° max. X 5° max. 8 ± 0.1 3.9 ± 0.1 1.5 ± 0.1 4.65 ± 0.1 Section X-X R0.76 Fig. 8 - Tape and Reel Packing for Option 8 (2000 units per reel) Rev. 1.7, 18-Feb-13 Document Number: 81775 7 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000