VS-16RIA100

VS-16RIA Series www.vishay.com Vishay Semiconductors Medium Power Phase Control Thyristors (Stud Version), 16 A FEATURES • Improved glass passivation for high reliability and exceptional stability at high temperature • High dI/dt and dV/dt capabilities • Standard package • Low thermal resistance • Metric threads version available TO-48 (TO-208AA) • Types up to 1200 V VDRM/VRRM • Designed and qualified for industrial and consumer level PRIMARY CHARACTERISTICS IT(AV) 16 A VDRM/VRRM 100 V, 200 V, 400 V, 600 V, 800 V, 1000 V, 1200 V VTM 1.75 V IGT 60 mA • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 TYPICAL APPLICATIONS • Medium power switching TJ -65 °C to +125 °C • Phase control applications Package TO-48 (TO-208AA) Circuit configuration Single SCR   MAJOR RATINGS AND CHARACTERISTICS PARAMETER TEST CONDITIONS IT(AV) I2t 16 A 85 °C 35 A 50 Hz 340 60 Hz 360 50 Hz 574 60 Hz 524 VDRM/VRRM tq UNITS TC IT(RMS) ITSM VALUES Typical TJ A A2s 100 to 1200 V 110 μs -65 to +125 °C ELECTRICAL SPECIFICATIONS VOLTAGE RATINGS TYPE NUMBER VS-16RIA VOLTAGE CODE VDRM/VRRM, MAXIMUM REPETITIVE PEAK AND OFF-STATE VOLTAGE (1) V VRSM, MAXIMUM NON-REPETITIVE IDRM/IRRM MAXIMUM PEAK VOLTAGE (2) AT TJ = TJ MAXIMUM mA V 10 100 150 20 200 300 40 400 500 60 600 700 80 800 900 100 1000 1100 120 1200 1300 20 10 Notes (1) Units may be broken over non-repetitively in the off-state direction without damage, if dI/dt does not exceed 20 A/μs (2) For voltage pulses with t  5 ms p Revision: 21-Sep-17 Document Number: 93695 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-16RIA Series www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Maximum average on-state current at case temperature Maximum RMS on-state current IT(AV) TEST CONDITIONS 180° sinusoidal conduction IT(RMS) t = 10 ms Maximum peak, one-cycle non-repetitive surge current ITSM t = 8.3 ms t = 10 ms t = 8.3 ms t = 10 ms Maximum I2t for fusing I2t t = 8.3 ms t = 10 ms t = 8.3 ms Maximum I2t for fusing I2t No voltage reapplied 16 A 85 °C 35 A 360 285 Sinusoidal half wave, initial TJ = TJ maximum 100 % VRRM reapplied 300 524 405 5740 (16.7 % x  x IT(AV) < I <  x IT(AV)), TJ = TJ maximum 0.97 High level value of threshold voltage VT(TO)2 (I >  x IT(AV)), TJ = TJ maximum 1.24 Low level value of on-state slope resistance rt1 (16.7 % x  x IT(AV) < I <  x IT(AV)),  TJ = TJ maximum 17.9 High level value of on-state slope resistance rt2 (I >  x IT(AV)), TJ = TJ maximum 13.6 Ipk = 50 A, TJ = 25 °C 1.75 VTM IH Latching current IL TJ = 25 °C, anode supply 6 V, resistive load A2s 375 t = 0.1 to 10 ms, no voltage reapplied, TJ = TJ maximum VT(TO)1 Maximum on-state voltage A 574 Low level value of threshold voltage Maximum holding current UNITS 340 No voltage reapplied 100 % VRRM reapplied VALUES A2s V m 130 200 V mA SWITCHING PARAMETER SYMBOL TEST CONDITIONS VDRM  600 V Maximum rate of rise of turned-on current VDRM  800 V VDRM  1000 V VALUES UNITS 200 dI/dt TJ = TJ maximum, VDM = Rated VDRM Gate pulse = 20 V, 15 , tp = 6 μs, tr = 0.1 μs maximum ITM = (2 x rated dI/dt) A VDRM  1600 V 180 160 A/μs 150 Typical turn-on time tgt TJ = 25 °C, at rated VDRM/VRRM, TJ = 125 °C Typical reverse recovery time trr TJ = TJ maximum, ITM = IT(AV), tp > 200 μs, dI/dt = - 10 A/μs Typical turn-off time tq TJ = TJ maximum, ITM = IT(AV), tp > 200 μs, VR = 100 V, dI/dt = - 10 A/μs, dV/dt = 20 V/μs linear to 67 % VDRM, gate bias 0 V to 100 W 0.9 4 μs 110 Note • tq = 10 μs up to 600 V, tq = 30 μs up to 1600 V available on special request BLOCKING PARAMETER Maximum critical rate of rise of off-state voltage SYMBOL dV/dt TEST CONDITIONS VALUES TJ = TJ maximum linear to 100 % rated VDRM 100 TJ = TJ maximum linear to 67 % rated VDRM 300 (1) UNITS V/μs Note (1) Available with: dV/dt = 1000 V/μs, to complete code add S90 i.e. 16RIA120S90 Revision: 21-Sep-17 Document Number: 93695 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-16RIA Series www.vishay.com Vishay Semiconductors TRIGGERING PARAMETER SYMBOL Maximum peak gate power PGM Maximum average gate power PG(AV) TEST CONDITIONS VALUES 8.0 TJ = TJ maximum 2.0 UNITS W Maximum peak positive gate current IGM TJ = TJ maximum 1.5 A Maximum peak negative gate voltage -VGM TJ = TJ maximum 10 V TJ = - 65 °C 90 DC gate current required to trigger IGT TJ = 25 °C TJ = 125 °C TJ = - 65 °C DC gate voltage required to trigger DC gate current not to trigger DC gate voltage not to trigger VGT IGD VGD 60 Maximum required gate trigger  current/voltage are the lowest value which will trigger all units 6 V anode to cathode applied 35 3.0 TJ = 25 °C 2.0 TJ = 125 °C 1.0 TJ = TJ maximum, VDRM = Rated value TJ = TJ maximum, VDRM = Rated value mA Maximum gate current/voltage not to trigger is the maximum value which will not trigger any unit with rated VDRM anode to cathode applied V 2.0 mA 0.2 V THERMAL AND MECHANICAL SPECIFICATIONS PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS -65 to +125 °C Maximum operating junction and storage temperature range TJ, TStg Maximum thermal resistance, junction to case RthJC DC operation 0.86 Maximum thermal resistance, case to heat sink RthCS Mounting surface, smooth, flat and greased 0.35 K/W TO NUT Lubricated threads (Non-lubricated threads) Mounting torque Approximate weight Case style See dimensions - link at the end of datasheet TO DEVICE 20 (27.5) 25 lbf in 0.23 (0.32) 0.29 kgf · m 2.3 (3.1) 2.8 N·m 14 g 0.49 oz. TO-48 (TO-208AA) RthJC CONDUCTION CONDUCTION ANGLE SINUSOIDAL CONDUCTION RECTANGULAR CONDUCTION 180° 0.21 0.15 120° 0.25 0.25 90° 0.31 0.34 60° 0.45 0.47 30° 0.76 0.76 TEST CONDITIONS UNITS TJ = TJ maximum K/W Note • The table above shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC Revision: 21-Sep-17 Document Number: 93695 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-16RIA Series 130 Vishay Semiconductors Maximum Allowable Case Temperature (°C) Maximum Allowable Case Temperature (°C) www.vishay.com 16RIA Series RthJC (DC) = 1.15 K/W 120 110 100 Conduction Angle 90 30° 80 60° 90° 120° 70 180° 60 50 0 5 10 15 20 130 16RIA Series RthJC (DC) = 1.15 K/W 120 110 100 Conduction Period 90 30° 60° 80 90° 120° 70 180° 60 DC 50 0 25 10 Fig. 1 - Current Ratings Characteristics 30 40 Fig. 2 - Current Ratings Characteristics 45 35 15 Conduction Angle 10 16RIA Series TJ = 125°C 5 R 20 a elt -D 3K /W 4K /W 5K /W 7K /W RMS Limit 25 K/ W W K/ 30 2 1 0. 180° 120° 90° 60° 30° 40 = A hS R t Maximum Average On-state Power Loss (W) 20 Average On-state Current (A) Average On-state Current (A) 10 K/ W 0 0 5 10 15 20 25 0 Average On-state Current (A) 25 50 75 100 125 Maximum Allowable Ambient Temperature (°C) 45 35 Conduction Period 10 16RIA Series TJ = 125°C 5 R RMS Limit 20 a elt -D 3K /W 4K /W 5K /W 7K /W 25 15 K/ W W K/ 30 2 1 0. DC 180° 120° 90° 60° 30° 40 = A hS R t Maximum Average On-state Power Loss (W) Fig. 3 - On-State Power Loss Characteristics 10 K/W 0 0 4 8 12 16 20 Average On-state Current (A) 24 28 0 25 50 75 100 125 Maximum Allowable Ambient Temperature (°C) Fig. 4 - On-State Power Loss Characteristics Revision: 21-Sep-17 Document Number: 93695 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-16RIA Series www.vishay.com 350 At Any Rated Load Condition And With Rated V RRMApplied Following Surge. Initial TJ= 125°C @ 60 Hz 0.0083 s @ 50 Hz 0.0100 s 280 260 Peak Half Sine Wave On-state Current (A) Peak Half Sine Wave On-state Current (A) 300 Vishay Semiconductors 240 220 200 180 16RIA Series 160 140 1 10 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. Initial TJ= 125°C No Voltage Reapplied Rated VRRMReapplied 325 300 275 250 225 200 175 16RIA Series 150 125 0.01 100 0.1 1 Pulse Train Duration (s) Number Of Equal Amplitude Half Cycle Current Pulses (N) Fig. 5 - Maximum Non-Repetitive Surge Current Fig. 6 - Maximum Non-Repetitive Surge Current 1000 Instantaneous On-state Current (A) 16RIA Series 100 10 TJ = 25°C TJ = 125°C 1 0.5 1 1.5 2 2.5 3 3.5 Instantaneous On-state Voltage (V) Transient Thermal Impedance Z thJC (K/W) Fig. 7 - Forward Voltage Drop Characteristics 10 Steady State Value RthJC = 1.15 K/W (DC Operation) 1 0.1 16RIA Series 0.01 0.001 0.01 0.1 1 10 Square Wave Pulse Duration (s) Fig. 8 - Thermal Impedance ZthJC Characteristics Revision: 21-Sep-17 Document Number: 93695 5 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-16RIA Series www.vishay.com Vishay Semiconductors Rectangular gate pulse a) Recommended load line for rated di/dt : 10V, 20ohms tr = 6 µs b) Recommended load line for