Y002412K5000B9L

H Series Vishay Foil Resistors New Generation of Secondary Standards Hermetically Sealed High Precision Bulk Metal® Foil Technology Resistors with TCR of ± 2 ppm/°C, Tolerance of ± 0.001 % and Load Life Stability of ± 0.005 % (Metrology, Laboratory, Instrumentation, Industrial) FEATURES The H series resistors are oil-filled, hermetically sealed ultra precision resistors and are used as secondary standards for metrology applications. The hermetic sealing eliminates the ingress of moisture and oxygen, while the oil acts as a thermal conductor, thus eliminating the long-term degradation elements of unsealed resistors, while at the same time allowing the device to accept short periods of overload without degradation. Vishay’s Bulk Metal® Foil outperforms all other resistor technologies available today for applications that require precision and stability. When combined with the hermetic sealing and oil filling, the H series resistors become the most precise and stable resistors available. With accuracies of 0.001 %, a resistance range from 5 Ω to 1.84 MΩ, and long term shelf life of less than 2 ppm, these devices are virtually secondary standards that can be carried in sets for daily or periodic calibration of factory measurement equipment. The H series is available with laboratory and metrology level precision and long-term stability with additional in-house oriented processes such as: chip stabilization, special TCR plotting, additional treatments for ultra stability and special post manufacturing operations (PMO). (Please refer to the last page) TABLE 1 - TCR VS. RESISTANCE VALUE RESISTANCE VALUE (Ω) TYPICAL TCR AND MAX. SPREAD (- 55 °C to + 125 °C, + 25 °C ref.) (ppm/°C) 100 to < 1M84 ± 2 ± 2.5 50 to < 100 ± 2 ± 3.5 5 to < 50 ± 2 ± 4.5 Note • For maximum TCR < 1 ppm/°C, see VHP100 and contact application engineering FIGURE 1 - SHELF LIFE - VHA518-11 12K9 VS. QHE Resistance Change (ppm) INTRODUCTION • Temperature coefficient of resistance (TCR): ± 2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C ref.). For ultra high performances (instrumentation and metrology) please refer to the last page • Resistance range: 5 Ω to 1.84 MΩ (higher or lower values of resistance available) • Vishay Foil resistors are not restricted to standard values; specific “as required” values can be supplied at no extra cost or delivery (e.g. 1K2345 vs. 1K) • Power rating: 0.3 W to 2.5 W at + 25 °C (depending on model - see table 2) • Tolerance: to ± 0.001 % (10 ppm) • Load life stability to ± 0.002 % (20 ppm) at 25 °C, 2000 h at rated power • Load life stability can be considerably improved through in-house stabilization • Shelf life stability: ± 2 ppm for at least 6 years (unaffected by humidity) • Electrostatic discharge (ESD) up to 25 000 V • Rise time: 1 ns effectively no ringing • Thermal stabilization time < 1 s (nominal value achieved within 10 ppm of steady state value) • Current noise: 0.010 µVRMS/V of applied voltage (< - 40 dB) • Thermal EMF: 0.05 µV/°C typical • Voltage coefficient: < 0.1 ppm/V • Non-inductive: < 0.08 µH • Non-inductive, non-capacitive design • Non hot spot design • Terminal finish available: lead (Pb)-free or tin/lead alloy • Impervious to harmful environments - oil-filled • Compliant to RoHS directive 2002/95/EC • Prototype quantities available in just 5 working days or sooner. For more information, please contact foil@vishaypg.com • For better performances (values, TCR, tolerance, stability), please see the HZ series 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 - 0.1 0 100 200 300 400 500 600 700 800 900 1000 Time (Days) * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 63006 Revision: 23-Mar-10 For any questions, contact: foil@vishaypg.com www.foilresistors.com 1 H Series Vishay Foil Resistors Percent of Rated Power FIGURE 2 - POWER DERATING CURVE + 100 - 55 °C + 75 + 50 + 25 0 - 50 - 25 0 + 25 + 50 + 75 + 100 + 125 + 150 + 175 Ambient Temperature (°C) FIGURE 3 - TRIMMING TO VALUES (Conceptual Illustration) FIGURE 4 - TYPICAL RESISTANCE/ TEMPERATURE CURVE + 150 + 100 Current Path Before Trimming Interloop Capacitance Reduction in Series Current Path After Trimming Trimming Process Removes this Material from Shorting Strip Area Changing Current Path and Increasing Resistance Mutual Inductance Reduction due to Change in Current Direction ΔR + 50 C Alloy 2 ppm/°C 0 R (ppm) - 50 - 100 2 ppm/°C - 150 - 200 - 55 - 25 0 + 25 + 50 + 75 + 100 + 125 Ambient Temperature (°C) Note: Foil shown in black, etched spaces in white TABLE 2 - MODEL SELECTION MODEL NUMBER STANDARD RESISTANCE RESISTANCE TOLERANCE PER RANGE MAXIMUM POWER AVERAGE CONSTRUCTION WORKING RANGE RATING WEIGHT BRIEF TIGHTEST VOLTAGE at + 25 °C RANGE (Ω) (g) (2) (%) (Ω) VHP202 5 to 100K > 100K to 150K 300 0.3 W 0.2 W 1.4 VHA412 5 to 100K > 100K to 150K 250 0.3 W 0.2 W 4.6 VHA414 5 to 200K > 200K to 335K 350 0.5 W 0.3 W 7.3 350 0.75 W 0.4 W 6.3 VHA512* 5 to 300K > 300K to 500K 5 to 400K > 400K to 668K 500K VHA516-5* 5> to 500K to 835K 600K VHA516-6* 5> to 600K to 1M 700K VHA518-7* 5> to 700K to 1M17 800K VHA518-8* 5> to 800K to 1M34 900K VHA518-9* 5> to 900K to 1M5 5 to 1.0M VHA518-10* > 1.0M to 1M67 1.0M VHA518-11* 5> to 1.0M to 1M84 VHA516-4* 1K to † (1) ± 0.001 500 to < 1K ± 0.0025 50 to < 500 ± 0.005 30 to < 50 ± 0.01 20 to < 30 ± 0.02 10 to < 20 ± 0.05 5 to < 10 ± 0.1 500 600 1.0 W 0.5 W 1.25 W 0.6 W 1.5 W 0.7 W 1.75 W 0.8 W 2.0 W 0.9 W 2.25 W 1.0 W 2.5 W 1.1 W 2.5 W 1.2 W Oil-filled, tinned copper leads, nickel shell, kovar and glass header DIMENSIONS (3) INCHES mm W: 0.162 ± 0.020 L: 0.415 ± 0.020 H: 0.430 ± 0.020** LL: 1.000 ± 0.125 LS: 0.150 ± 0.010 (4) ST: 0.095 max. L: 0.625 ± 0.031 D: 0.375 ± 0.031 LL: 1.000 min. L: 1.000 ± 0.031 D: 0.375 ± 0.031 LL: 1.000 min. L: 0.625 ± 0.031 D: 0.500 ± 0.031 LL: 1.000 min. 4.11 ± 0.51 10.54 ± 0.51 10.92 ± 0.51 25.4 ± 3.18 3.81 ± 0.25 2.41 max. 15.88 ± 0.79 9.53 ± 0.79 25.4 min. 25.4 ± 0.79 9.53 ± 0.79 25.4 min. 15.88 ± 0.79 12.7 ± 0.79 25.4 min. 9.2 Oil-filled, tinned copper leads, L: 1.000 ± 0.031 tinned brass shell, D: 0.500 ± 0.031 LL: 1.000 min. kovar and glass end bells 25.4 ± 0.79 12.7 ± 0.79 25.4 min. 13.5 L: 1.500 ± 0.031 D: 0.500 ± 0.031 LL: 1.000 min. 38.1 ± 0.79 12.7 ± 0.79 25.4 min. Notes * Available in a 4-lead terminal ** 0.375 H available See next page for numbered footnotes www.foilresistors.com 2 For any questions, contact: foil@vishaypg.com Document Number: 63006 Revision: 23-Mar-10 H Series Vishay Foil Resistors FIGURE 5 - STANDARD IMPRINTING AND DIMENSIONS Front View L H VISHAY XXXX VHP202 Rear View Lead Material #22 AWG Round Solder Coated Copper W Resistance Value Code 100R01 0.01% XXXX Model Number D VISHAY XXXX Tolerance Serial No. Date Code 07 10 Year Week L LL ST Date Code 07 06 Year Week LL LS Model No. VHA412 100R01 0.005% Lead Material #22 AWG Round Solder Coated Copper Resistance Value Code Tolerance TABLE 3 - “H” SERIES SPECIFICATIONS Stability (8) Load life at 2000 h ± 0.002 % (20 ppm) at 25 °C at rated power Shelf life ± 2 ppm (0.0002 %) for at least 6 years Current Noise < - 40 dB High Frequency Operation Rise time Inductance (L) 1.0 ns without ringing (5) 0.1 µH maximum; 0.08 µH typical Capacitance (C) 1.0 pF maximum; 0.5 pF typical Voltage Coefficient < 0.1 ppm/V (6) Thermal EMF (7) 0.1 µV/°C maximum; 0.05 µV/°C typical; 1 µV/W maximum Hermeticity 10-7 atmospheric cc/s maximum Notes (1) Upper end of resistance range varies with model selected (i.e. VHP202; the range is to 150 kΩ; VHA518-10, the range is to 1M67 Ω) per table 2 (2) Not to exceed power rating of resistor (3) Insulating sleeve - a special case insulating plastic sleeve is available on VHA models. See table 4 for instructions on how to specify (4) 0.200" (5.08 mm) lead spacing available - specify VH202J (5) Inductance (L) due mainly to the leads (6) The resolution limit of existing test equipment (within measurement capability of the equipment, or “essentially zero”) (7) µV/°C relates to EMF due to lead temperature difference and µV/W due to power applied to the resistor (8) Load life ΔR maximum. Can be reduced through in-house oriented processes POST MANUFACTURING OPERATIONS OR PMO FOR IMPROVED END OF LIFE Many analog applications can include requirements for performance under conditions of stress beyond the normal and over extended periods of time. This calls for more than just selecting a standard device and applying it to a circuit. The standard device may turn out to be all that is needed but an analysis of the projected service conditions should be made and it may well dictate a routine of stabilization known as post manufacturing operations or PMO. The PMO operations that will be discussed are only applicable to Bulk Metal Foil resistors. They stabilize Bulk Metal Foil resistors while they are harmful to other types. Short time overload, Document Number: 63006 Revision: 23-Mar-10 accelerated load life, and temperature cycling are the three PMO exercises that do the most to remove the anomalies down the road. Vishay Bulk Metal Foil resistors are inherently stable as manufactured. These PMO exercises are only of value on Bulk Metal Foil resistors and they improve the performance by amounts that are small but significant when compared to the very tight tolerances. Users are encouraged to contact Vishay Foil applications engineering for assistance in choosing the PMO operations that are right for their application. For any questions, contact: foil@vishaypg.com www.foilresistors.com 3 H Series Vishay Foil Resistors TABLE 4 - GLOBAL PART NUMBER INFORMATION (1) NEW GLOBAL PART NUMBER: Y0019120K500V9L (preferred part number format) DENOTES PRECISION VALUE CHARACTERISTICS Y R=Ω K = kΩ M = MΩ 0 = standard 1 = tin/lead with plastic sleeve 9 = lead (Pb)-free 19 = lead (Pb)-free with plastic sleeves 2 to 999 = custom Y 0 0 1 9 1 2 0 K 5 0 0 V 9 L PRODUCT CODE RESISTANCE TOLERANCE PACKAGING 0024 = VHP202 and VH202C 0019 = VHA412 0025 = VHA414 0023 = VHA512 1725 = VHA512 (4-terminals) 0104 = VHA516-4 1726 = VHA516-4 (4-terminals) 0105 = VHA516-5 1727 = VHA516-5 (4-terminals) 0106 = VHA516-6 1728 = VHA516-6 (4-terminals) 0107 = VHA518-7 1729 = VHA518-7 (4-terminals) 0108 = VHA518-8 1730 = VHA518-8 (4-terminals) 0109 = VHA518-9 1731 = VHA518-9 (4-terminals) 0110 = VHA518-10 1732 = VHA518-10 (4-terminals) 0111 = VHA518-11 1733 = VHA518-11 (4-terminals) S = ± 0.001 % U = ± 0.002 % X = ± 0.0025 % V = ± 0.005 % T = ± 0.01 % Q = ± 0.02 % A = ± 0.05 % B = ± 0.1 % C = ± 0.25 % D = ± 0.5 % F = ± 1.0 % L = bulk pack FOR EXAMPLE: ABOVE GLOBAL ORDER Y0019 120K500 V 9 L: TYPE: VHA412 VALUE: 120.5 kΩ ABSOLUTE TOLERANCE: ± 0.005 % TERMINATION: lead (Pb)-free PACKAGING: bulk pack HISTORICAL PART NUMBER: VHA412T 120K50 V B (will continue to be used) VHA412 T 120K50 V B PACKAGING B = bulk pack MODEL TERMINATION PLASTIC SLEEVE OHMIC VALUE TOLERANCE VHP202 and VH202C VHA412 VHA414 VHA512 (2) VHA516-4 (2) VHA516-5 (2) VHA516-6 (2) VHA518-7 (2) VHA518-8 (2) VHA518-9 (2) VHA518-10 (2) VHA518-11 (2) T = lead (Pb)-free None = tin/lead P = plastic sleeve None = standard 120K50 = 120.5 kΩ S = ± 0.001 % U = ± 0.002 % X = ± 0.0025 % V = ± 0.005 % T = ± 0.01 % Q = ± 0.02 % A = ± 0.05 % B = ± 0.1 % C = ± 0.25 % D = ± 0.5 % F = ± 1.0 % Notes (1) For non-standard requests, please contact application engineering (2) 4-terminal construction of these types are available, please quote: 2-Terminal VHA512 VHA516-4 VHA516-5 VHA516-6 VHA518-7 VHA518-8 VHA518-9 VHA518-10 VHA518-11 4-Terminal 302073 302074-4 302074-5 302074-6 302075-7 302075-8 302075-9 302075-10 302075-11 www.foilresistors.com 4 For any questions, contact: foil@vishaypg.com Document Number: 63006 Revision: 23-Mar-10 H Series Vishay Foil Resistors ULTRA HIGH PRECISION HERMETICALLY SEALED RESISTORS APPLICATIONS INCLUDE INTRODUCTION The response of Vishay's hermetically sealed resistors under variable conditions and stresses can be made better by additional in-house oriented processes (PMO). Processes such as short time overload, accelerated load life and temperature cycling produce enhanced levels of accuracy, stability and speed, offering immediate answers to many resistor applications currently believed unsolvable, and opens entirely new areas of design where the use of resistors had not been considered. • Resistance standards • Feedback devices for operational amplifiers • Precision voltage dividers • Meter multipliers • Precision bridge resistors • Decade voltage dividers See table 5 for the improvement to expect in hermetically sealed parts when calling for Vishay in-house oriented processes (PMO). TABLE 5 - EXAMPLES OF NON-STANDARD REQUIREMENTS TYPE VHA518-11 Set of 10 Resistors (+ 20 °C to + 30 °C) VHA518-7 4-Terminal (+ 20 °C to + 30 °C) VHA518-7 4-Terminal Matched Pairs (+ 20 °C to + 30 °C) VHA518 Set of 10 Resistors (+ 18 °C to + 28 °C, + 23 °C ref.) VALUE TOLERANCE TCR ABSOLUTE MATCH ABSOLUTE TRACKING 1Ω 0.1 % 0.005 % 0.5 ppm/°C 0.5 ppm/°C 10 Ω 0.05 % - 0.5 ppm/°C - 100 Ω 0.01 % - 0.5 ppm/°C - 120 Ω 0.005 % - 0.4 ppm/°C - 1K 0.005 % - 0.3 ppm/°C - 10K 0.001 % - 0.3 ppm/°C - 100K 0.001 % - 0.3 ppm/°C - 10 Ω 0.05 % 0.02 % 0.5 ppm/°C 0.5 ppm/°C 100 Ω 0.01 % 0.01 % 0.5 ppm/°C 0.5 ppm/°C REMARKS with PMO with PMO 1K 0.005 % 0.002 % 0.3 ppm/°C 0.3 ppm/°C 10K 0.001 % 0.002 % 0.3 ppm/°C 0.3 ppm/°C 100K 0.001 % 0.002 % 0.3 ppm/°C 0.3 ppm/°C 999Ω475 0.05 % 0.005 % 0.5 ppm/°C 0.5 ppm/°C with PMO with PMO ORDERING INFORMATION Resistors are built to your requirements. Send your schematic and electrical requirements to the applications engineering department at foil@vishaypg.com. A unique part number will be assigned which defines all aspects of your resistor. Document Number: 63006 Revision: 23-Mar-10 For any questions, contact: foil@vishaypg.com www.foilresistors.com 5 Legal Disclaimer Notice Vishay Precision Group Disclaimer ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE. Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay Precision Group”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. The product specifications do not expand or otherwise modify Vishay Precision Group’s terms and conditions of purchase, including but not limited to, the warranty expressed therein. Vishay Precision Group makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase. To the maximum extent permitted by applicable law, Vishay Precision Group disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Information provided in datasheets and/or specifications may vary from actual results in different applications and performance may vary over time. Statements regarding the suitability of products for certain types of applications are based on Vishay Precision Group’s knowledge of typical requirements that are often placed on Vishay Precision Group products. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any conduct of Vishay Precision Group. The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay Precision Group products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay Precision Group for any damages arising or resulting from such use or sale. Please contact authorized Vishay Precision Group personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document No.: 63999 Revision: 27-Apr-2011 www.vishaypg.com 1 Legal Disclaimer Notice Vishay Precision Group, Inc. Disclaimer ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE. Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “VPG”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. The product specifications do not expand or otherwise modify VPG’s terms and conditions of purchase, including but not limited to, the warranty expressed therein. VPG makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase. To the maximum extent permitted by applicable law, VPG disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Information provided in datasheets and/or specifications may vary from actual results in different applications and performance may vary over time. Statements regarding the suitability of products for certain types of applications are based on VPG’s knowledge of typical requirements that are often placed on VPG products. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. You should ensure you have the current version of the relevant information by contacting VPG prior to performing installation or use of the product, such as on our website at vpgsensors.com. No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any conduct of VPG. The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise expressly indicated. Customers using or selling VPG products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify VPG for any damages arising or resulting from such use or sale. Please contact authorized VPG personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Copyright Vishay Precision Group, Inc., 2014. All rights reserved. Document No.: 63999 Revision: 15-Jul-2014 www.vpgsensors.com 1