Y0075100K000F0L

VSR Series Vishay Foil Resistors Bulk Metal® Foil Technology Industrial Precision Resistors with TCR of ± 4 ppm/°C and Tolerance of ± 0.01 % FEATURES INTRODUCTION Bulk Metal® Foil technology out performs all other resistor technologies available today for applications that require high precision and high stability. This technology has been pioneered and developed by VISHAY, and products based on this technology are the most suitable for a wide range of applications. Generally Bulk Metal Foil technology allows us to produce customer orientated products designed to satisfy challenging and specific technical requirements. The VSR series of resistors is a low cost version of the well established S series of resistors. These resistors are made of foil elements so all of the inherent performance of foil is retained. They do not however, have the same TCR or tolerance ranges (see table 1 for details). These products find a wide range of usage in high end stereo equipment and some grades of test and measurement equipment. Standoffs are dimensioned to provide a minimum lead clearance of 0.010" between the resistor body and the printed circuit board, when the standoffs are seated on the board. This allows for proper cleaning after the soldering process. Our applications engineering department is available to advise and to make recommendations for non standard technical requirements and special applications, please contact us. • Temperature coefficient of resistance (TCR) (1): ± 4 ppm/°C (0 °C to + 60 °C) ± 8 ppm/°C (- 55 °C to + 125 °C, + 25 °C ref.) • Resistance range: 0.5 Ω to 1 MΩ (higher or lower values of resistance are available) • Vishay Foil resistors are not restricted to standard values, we can supply specific “as required” values at no extra cost or delivery (e.g. 1K2345 vs. 1K) • Tolerance: to ± 0.01 % (100 ppm) • Load life stability: to ± 0.005 % at 70 °C, 2000 h at rated power • Electrostatic discharge up to 25 000 V • Non inductive, non capacitive design • Rise time: 1 ns effectively no ringing • Current noise: - 40 dB • Thermal EMF: 0.05 µV/°C typical • Voltage coefficient: < 0.1 ppm/V • Inductance: 0.08 µH • Matched sets available • Terminal finish: lead (Pb)-free tin/lead alloy • Prototype samples available from 72 h. For more information, please contact foil@vishay.com • For better performances please review the S Series datasheet Note (1) APPLICATIONS • • • • • Percent of Rated Power at + 125 °C FIGURE 1 - POWER DERATING CURVE 200 % - 55 °C For values below 50 Ω please contact application engineering Industrial Medical Audio (high end stereo equipment) Test and measurement equipment Precision amplifiers FIGURE 2 - TRIMMING TO VALUES (Conceptual Illustration) + 70 °C Double Rated Power 175 % 150 % Interloop Capacitance Reduction in Series 125 % Rated Power 100 % 75 % Safe operation for < 150 ppm Δ R after 2000 hours load-life. 50 % Mutual Inductance Reduction due to Change in Current Direction 25 % 0 - 75 Current Path Before Trimming - 50 - 25 0 + 25 + 50 + 75 Current Path After Trimming Trimming Process Removes this Material from Shorting Strip Area Changing Current Path and Increasing Resistance + 100 + 125 + 150 + 175 + 200 Ambient Temperature (°C) Note: Foil shown in black, etched spaces in white * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 63009 Revision: 23-Mar-10 For any questions, contact: foil@vishaypg.com www.foilresistors.com 1 VSR Series Vishay Foil Resistors FIGURE 3 - IMPRINTING AND DIMENSIONS Front View L H VISHAY XXXX VSR4 Rear View W Resistance Value Code Date Code 07 10 Year Week 100R01 0.01 % Tolerance ST LS LL SW Lead Material #22AWG Round Solder Coated Copper Model Number TABLE 1 - MODEL SELECTION DIMENSIONS MODEL RESISTANCE NUMBER (Ω) VSR 1 to 150K POWER POWER MAXIMUM at at WORKING + 70 °C + 125 °C VOLTAGE 0.3 W 0.2 W 300 up to 100K VSRJ (1). 0.25 W 0.15 W over 100K VSR4 1 to 500K 0.5 W 0.4 W 350 up to 200K 0.25 W 0.2 W over 200K VSR5 1 to 750K 0.75 W 0.6 W 350 up to 300K 0.4 W 0.3 W over 300K VSR6 0.5 to 1M 1.0 W 0.8 W 500 up to 400K 0.5 W 0.4 W over 400K INCHES mm W: 0.105 ± 0.010 2.67 ± 0.25 L: 0.300 ± 0.010 7.62 ± 0.25 H: 0.326 ± 0.010 8.28 ± 0.25 ST: 0.010 minimum 0.254 minimum SW: 0.040 ± 0.005 1.02 ± 0.13 LL: 1.000 ± 0.125 25.4 ± 3.18 LS: 0.150 ± 0.0051) 3.81 ± 0.13 MAXIMUM LOAD LIFE TEMPERATURE STABILITY COEFFICIENT (MAXIMUM OF RESISTANCE ΔR) (+ 25 °C REF.) 0.05 % 2000 hours at + 125 °C 0 °C to + 60 °C ± 4 ppm/°C - 55 °C to + 125 °C ± 8 ppm/°C W: 0.160 maximum 4.06 maximum L: 0.575 maximum 14.61 maximum H: 0.413 maximum 10.49 maximum 0.89 ± 0.13 ST: 0.035 ± 0.005 1.27 ± 0.13 SW: 0.050 ± 0.005 25.4 ± 3.18 LL: 1.000 ± 0.125 10.16 ± 0.51 LS: 0.400 ± 0.020 TIGHTEST TOLERANCE % VS. LOWEST RESISTANCE VALUE (Ω) ± 0.01/50 ± 0.02/30 ± 0.05/5 ± 0.1/2 ± 0.5/1 ± 0.005/100 ± 0.01/50 W: 0.160 maximum 4.06 maximum L: 0.820 maximum 20.83 maximum H: 0.413 maximum 10.49 maximum 0.89 ± 0.13 ST: 0.035 ± 0.005 1.27 ± 0.13 SW: 0.050 ± 0.005 25.4 ± 3.18 LL: 1.000 ± 0.125 16.51 ± 0.51 LS: 0.650 ± 0.020 ± 0.02/30 ± 0.05/5 ± 0.1/2 W: 0.260 maximum 6.60 maximum L: 1.200 maximum 30.48 maximum H: 0.413 maximum 10.49 maximum 0.89 ± 0.13 ST: 0.035 ± 0.005 1.27 ± 0.13 SW: 0.050 ± 0.005 25.4 ± 3.18 LL: 1.000 ± 0.125 22.86 ± 0.51 LS: 0.900 ± 0.020 ± 0.5/1 Note (1) 0.200" (5.08 mm) lead spacing available - specify VSRJ. FIGURE 4 - TEMPERATURE COEFFICIENT OF RESISTANCE + 400 + 200 + 100 ΔR R 0 (ppm) - 100 + 4 ppm/°C + 140 - 4 ppm/°C - 140 - 200 - 400 0 + 25 + 60 Temperature, °C www.foilresistors.com 2 For any questions, contact: foil@vishaypg.com Document Number: 63009 Revision: 23-Mar-10 VSR Series Vishay Foil Resistors TABLE 2 - GLOBAL PART NUMBER INFORMATION NEW GLOBAL PART NUMBER: Y0075100K250A9L (preferred part number format) DENOTES PRECISION VALUE CHARACTERISTICS (1) Y R=Ω K = kΩ M = MΩ 0 = standard 9 = lead (Pb)-free 1 - 999 = custom Y 0 0 7 5 1 0 0 K 2 5 0 A 9 PRODUCT CODE RESISTANCE TOLERANCE PACKAGING 0075 = VSR 0789 = VSRJ 0020 = VSR4 0021 = VSR5 0022 = VSR6 T = ± 0.01 % Q = ± 0.02 % A = ± 0.05 % B = ± 0.1 % C = ± 0.25 % D = ± 0.5 % F = ± 1.0 % L = bulk pack L FOR EXAMPLE: ABOVE GLOBAL ORDER Y0075 100K250 A 9 L: TYPE: VSR VALUE: 100.25 kΩ ABSOLUTE TOLERANCE: ± 0.05 % TERMINATION: lead (Pb)-free PACKAGING: bulk pack HISTORICAL PART NUMBER EXAMPLE: VSRT 100K25 A B (will continue to be used) VSR T 100K25 A B MODEL TERMINATION OHMIC VALUE RESISTANCE TOLERANCE PACKAGING VSR VSRJ VSR4 VSR5 VSR6 T = lead (Pb)-free None = tin/lead alloy 100.25 kΩ T = ± 0.01 % Q = ± 0.02 % A = ± 0.05 % B = ± 0.1 % C = ± 0.25 % D = ± 0.5 % F = ± 1.0 % B = bulk pack Note (1) For non-standard requests, please contact application engineering. Document Number: 63009 Revision: 23-Mar-10 For any questions, contact: foil@vishaypg.com www.foilresistors.com 3 Legal Disclaimer Notice Vishay Precision Group, Inc. Disclaimer ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE. Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “VPG”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. The product specifications do not expand or otherwise modify VPG’s terms and conditions of purchase, including but not limited to, the warranty expressed therein. VPG makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase. To the maximum extent permitted by applicable law, VPG disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Information provided in datasheets and/or specifications may vary from actual results in different applications and performance may vary over time. Statements regarding the suitability of products for certain types of applications are based on VPG’s knowledge of typical requirements that are often placed on VPG products. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. You should ensure you have the current version of the relevant information by contacting VPG prior to performing installation or use of the product, such as on our website at vpgsensors.com. No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any conduct of VPG. The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise expressly indicated. Customers using or selling VPG products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify VPG for any damages arising or resulting from such use or sale. Please contact authorized VPG personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Copyright Vishay Precision Group, Inc., 2014. All rights reserved. Document No.: 63999 Revision: 15-Jul-2014 www.vpgsensors.com 1