T436432B

tm • • • • • TE CH T436432B SDRAM FEATURES 3.3V power supply Clock cycle time : 5 / 5.5 / 6 / 7 / 8 / 10 ns Internal four banks operation LVTTL compatible with multiplexed address All inputs are sampled at the positive going edge of system clock • Burst Read Single-bit Write operation • DQM for masking • Auto refresh and self refresh • 64ms refresh period (4K cycle) • MRS cycle with address key programs - CAS Latency ( 2 & 3 ) - Burst Length : 1 , 2 , 4 , 8 or full page for Sequential Burst 1 , 2 , 4 or 8 for Interleave Burst • Available package type : - 86 pin 400mil TSOP(II) and Lead free • Operating temperature : - 0 ~ +70 °C 2M x 32 SDRAM 512K x 32bit x 4Banks Synchronous DRAM GRNERAL DESCRIPTION The T436432B is 67,108,864 bits synchronous high data rate Dynamic RAM organized as 4 x 524,288 words by 32 bits , fabricated with high performance CMOS technology . Synchronous design allows precise cycle control with the use of system clock I/O transactions are possible on every clock cycle . Range of operating frequencies , programmable burst length and programmable latencies allow the same device to be useful for a variety of high bandwidth , high performance memory system applications. PART NUMBER EXAMPLES PART NO. CLOCK CYCLE TIME 5ns 5ns 5.5ns 5.5ns 6ns 6ns 7ns 7ns 8ns 8ns 10ns 10ns MAX FREQUENCY PACKAGE TSOP-II Lead free TSOP-II TSOP-II Lead free TSOP-II TSOP-II Lead free TSOP-II TSOP-II Lead free TSOP-II TSOP-II Lead free TSOP-II TSOP-II Lead free TSOP-II OPERATING TEMPERATURE T436432B-5SG T436432B-5S T436432B-55SG T436432B-55S T436432B-6SG T436432B-6S T436432B-7SG T436432B-7S T436432B-8SG T436432B-8S T436432B-10SG T436432B-10S 200 MHz 200 MHz 183 MHz 183 MHz 166 MHz 166 MHz 143 MHz 143 MHz 125 MHz 125 MHz 100 MHz 100 MHz 0 ~ +70 °C 0 ~ +70 °C 0 ~ +70 °C 0 ~ +70 °C 0 ~ +70 °C 0 ~ +70 °C 0 ~ +70 °C 0 ~ +70 °C 0 ~ +70 °C 0 ~ +70 °C 0 ~ +70 °C 0 ~ +70 °C TM Technology Inc. reserves the right P. 1 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm V DD TE CH T436432B PIN ARRANGEMENT (TSOP-II Top View) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 86 85 84 83 82 81 80 79 78 77 76 V ss D Q 15 V SSQ DQ0 V DDQ DQ1 DQ2 V SSQ D Q 14 D Q 13 V DDQ DQ3 DQ4 V DDQ D Q 12 D Q 11 V SSQ DQ5 DQ6 V SSQ D Q 10 DQ9 V DDQ DQ7 N .C V DD 8 6 P IN T S O P (II) (4 0 0 m il) 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 DQ8 N .C V ss DQM1 N .C N .C CLK CKE A9 A8 A7 A6 A5 A4 A3 DQM3 V SS DQM0 WE CAS RAS CS N .C BS0 BS1 A 1 0 /A P A0 A1 A2 DQM2 V DD N .C D Q 16 V SSQ N .C D Q 31 V DDQ D Q 17 D Q 18 V DDQ D Q 30 D Q 29 V SSQ D Q 19 D Q 20 V SSQ D Q 28 D Q 27 V DDQ D Q 21 D Q 22 V DDQ D Q 26 D Q 25 V SSQ D Q 23 V DD D Q 24 V ss TM Technology Inc. reserves the right P. 2 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B BLOCK DIAGRAM I/O Control Bank Select D ata Input R egister 512K x 32 512K x 32 512K x 32 512K x 32 Row Decoder Row Buffeer Refresh Counter Sense AM P Output Buffer DQ Address Register A DD C olum n D ecoder Tim ing Register Col. Buffer Latency & Burst Length Program m ing R egister C LK C KE CS R AS C AS WE D QM TM Technology Inc. reserves the right P. 3 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm PIN CLK TE CH T436432B PIN DESCRIPTION NAME System Clock Chip Select INPUT FUNCTION Active on the positive going edge to sample all input. Disables or enables device operation by masking or enabling all input except CLK,CKE and DQM Masks system clock to freeze operation from the next clock cycle. CS CKE Clock Enable CKE should be enabled at least one cycle prior to new command. Disable input buffers for power down in standby. Row/column addresses are multiplexed on the same pins. A0 ~ A10/AP Address Row address : RA0 ~ RA10,column address : CA0 ~ CA7 Auot-precharge flag : A10/AP BS0~1 Bank Select Address Selects bank to be activated during row address latch time. Select bank for read/write during column address latch time. Latches row addresses on the positive going edge of the CLK RAS Row Address Strobe with RAS low. Enables row access & precharge. Latches column addresses on the positive going edge of the CLK CAS Column Address Strobe with C AS low. Enables column access . Enables write operation and row precharge. Latches data in starting from CAS , WE active. Makes data output Hi-Z, tSHZ after the clock and masks the output. Blocks data input when DQM active. Data inputs/outputs are multiplexed on the same pins. WE DQM0~3 DQ0 ~ DQ31 VDD/VSS VDDQ/VSSQ N.C Write Enable Data Input/Output Mask Data Input/Output Data Output Power/Ground No Connection Power Supply/Ground Power and ground for the input buffers and the core logic. Isolated power supply and ground for the output buffers to provide improved noise immunity. No Connection. TM Technology Inc. reserves the right P. 4 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm BankActivate BankPrecharge PrechargeAll Write TE CH T436432B Operation Mode Fully synchronous operations are performed to latch the commands at the positive edges of CLK. Table 2 shows the truth table for the operation commands. Table 2. Truth Table (Note (1), (2) ) Command State Idle(3) Any Any Active(3) Active(3) Active(3) Active(3) Idle Any Active(4) Any Idle Idle Idle (SelfRefresh) CKEn-1 CKEn DQM(6) BS0,1 H H H H H H H H H H H H H L H H L L H X X X X X X X X X X X H L H L L H H X X X X X X X X X X X X X X X X X X X L X X X X X X X X X X X V V X V V V V A10 L H L H L H A9-0 X X Column address (A0 ~ A7) Column address (A0 ~ A7) CS# RAS# CAS# WE# L L L L L L L L L L L H H H H L H H X L L X H X X H X X H X X H H H L L L L L H H X L L X H X X H X X H X X H L L L L H H L H L X H H X H X X H X X H X X Row address Write and AutoPrecharge Read Read and Autoprecharge Mode Register Set No-Operation Burst Stop Device Deselect AutoRefresh SelfRefresh Entry SelfRefresh Exit OP code X X X X X X X X X X X X X X X X X X X X X X L L H L L H L X H L X H L X Clock Suspend Mode Entry Power Down Mode Entry Active Any(5) Active Any (PowerDown) Clock Suspend Mode Exit Power Down Mode Exit Data Write/Output Enable Data Mask/Output Disable Active Note: Active H X H X X X X 1. V = Valid, X = Don't care, L = Logic low, H = Logic high 2. CKEn signal is input level when commands are provided. CKEn-1 signal is input level one clock cycle before the commands are provided. 3. These are states of bank designated by BS signal. 4. Device state is 1, 2, 4, 8, and full page burst operation. 5. Power Down Mode can not enter in the burst operation. When this command is asserted in the burst cycle, device state is clock suspend mode. 6. DQM0-3 TM Technology Inc. reserves the right P. 5 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm 1 TE CH T436432B Commands BankActivate (RAS# = "L", CAS# = "H", WE# = "H", BS = Bank, A0-A10 = Row Address) The BankActivate command activates the idle bank designated by the BS0,1 (Bank Select) signal. By latching the row address on A0 to A10 at the time of this command, the selected row access is initiated. The read or write operation in the same bank can occur after a time delay of tRCD(min.) from the time of bank activation. A subsequent BankActivate command to a different row in the same bank can only be issued after the previous active row has been precharged (refer to the following figure). The minimum time interval between successive BankActivate commands to the same bank is defined by tRC(min.). The SDRAM has four internal banks on the same chip and shares part of the internal circuitry to reduce chip area; therefore it restricts the back-to-back activation of the four banks. tRRD(min.) specifies the minimum time required between activating different banks. After this command is used, the Write command and the Block Write command perform the no mask write operation. T0 CLK Bank A Row Addr. RAS# - CAS# delay (tRCD) COMM AND Bank A Activate NOP NOP R/W A with AutoPrecharge T1 T2 T3 .............. Bank A Col Addr. .............. Tn+3 Tn+4 Tn+5 Tn+6 ADDRESS Bank B Row Addr. RAS# - RAS# delay time (tRRD) Bank A Row Addr. .............. Bank B Activate NOP NOP Bank A Activate RAS# Cycle time (tRC) AutoPrecharge Begin : "H" or "L" BankActivate Command Cycle (Burst Length = n, CAS# Latency = 3) 2 BankPrecharge command (RAS# = "L", CAS# = "H", WE# = "L", BS = Bank, A10 = "L", A0-A9 = Don't care) The BankPrecharge command precharges the bank disignated by BS0,1 signal. The precharged bank is switched from the active state to the idle state. This command can be asserted anytime after tRAS(min.) is satisfied from the BankActivate command in the desired bank. The maximum time any bank can be active is specified by tRAS(max.). Therefore, the precharge function must be performed in any active bank within tRAS(max.). At the end of precharge, the precharged bank is still in the idle state and is ready to be activated again. PrechargeAll command (RAS# = "L", CAS# = "H", WE# = "L", BS = Don’t care, A10 = "H", A0-A9 = Don't care) The PrechargeAll command precharges all the four banks simultaneously and can be issued even if all banks are not in the active state. All banks are then switched to the idle state. Read command (RAS# = "H", CAS# = "L", WE# = "H", BS = Bank, A10 = "L", A0-A7 = Column Address) The Read command is used to read a burst of data on consecutive clock cycles from an active row in an active bank. The bank must be active for at least tRCD(min.) before the Read command is issued. During read bursts, the valid data-out element from the starting column address will be available following the CAS# latency after the issue of the Read command. Each subsequent data-out element will be valid by the next positive clock edge (refer to the following figure). The DQs go into high-impedance at the end of the burst unless other command is initiated. The burst length, burst sequence, and CAS# latency are determined by the mode register which is already programmed. A full-page burst will continue until terminated (at the end of the page it will wrap to column 0 and continue). 3 4 TM Technology Inc. reserves the right P. 6 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK COMMAND CAS# latency=2 tCK2, DQ's CAS# latency=3 tCK3, DQ's TE CH T0 T1 T2 T3 T4 T5 T6 T7 T436432B T8 READ A NOP NOP NOP NOP NOP NOP NOP NOP DOUT A0 DOUT A1 DOUT A2 DOUT A3 DOUT A0 DOUT A1 DOUT A2 DOUT A3 Burst Read Operation(Burst Length = 4, CAS# Latency = 2, 3) The read data appears on the DQs subject to the values on the DQM inputs two clocks earlier (i.e. DQM latency is two clocks for output buffers). A read burst without the auto precharge function may be interrupted by a subsequent Read or Write command to the same bank or the other active bank before the end of the burst length. It may be interrupted by a BankPrecharge/ PrechargeAll command to the same bank too. The interrupt coming from the Read command can occur on any clock cycle following a previous Read command (refer to the following figure). T0 T1 T2 T3 T4 T5 T6 T7 T8 CLK COMMAND READ A READ B NOP NOP NOP NOP NOP NOP NOP CAS# latency=2 tCK2, DQ's CAS# latency=3 tCK3, DQ's DOUT A0 DOUT B0 DOUT B1 DOUT B2 DOUT B3 DOUT A0 DOUT B0 DOUT B1 DOUT B2 DOUT B3 Read Interrupted by a Read (Burst Length = 4, CAS# Latency = 2, 3) The DQM inputs are used to avoid I/O contention on the DQ pins when the interrupt comes from a Write command. The DQMs must be asserted (HIGH) at least two clocks prior to the Write command to suppress data-out on the DQ pins. To guarantee the DQ pins against I/O contention, a single cycle with high-impedance on the DQ pins must occur between the last read data and the Write command (refer to the following three figures). If the data output of the burst read occurs at the second clock of the burst write, the DQMs must be asserted (HIGH) at least one clock prior to the Write command to avoid internal bus contention. TM Technology Inc. reserves the right P. 7 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK DQM COMMAND TE CH T0 T1 T2 T3 T4 T5 T6 T7 T436432B T8 NOP READ A NOP NOP NOP NOP WRITE B NOP NOP DQ's DOUT A0 Must be Hi-Z before the Write Command DINB 0 DINB1 DINB 2 : "H" or "L" Read to Write Interval (Burst Length • 4, CAS# Latency = 3) T0 CLK T1 T2 T3 T4 T5 T6 T7 T8 1 Clk Interval DQM COMMAND NOP NOP BANKA ACTIVATE NOP READ A WRITE A NOP NOP NOP CAS# latency=2 tCK2, DQ's DIN A0 DIN A1 DIN A2 DIN A3 : "H" or "L" Read to Write Interval (Burst Length ≥ 4, CAS# Latency = 2) T0 T1 T2 T3 T4 T5 T6 T7 T8 CLK DQM COMMAND CAS# latency=2 tCK2, DQ's NOP NOP READ A NOP NOP WRITE B NOP NOP NOP DIN B0 DIN B1 DIN B2 DIN B3 : "H" or "L" Read to Write Interval (Burst Length ≥ 4, CAS# Latency = 2) A read burst without the auto precharge function may be interrupted by a BankPrecharge/ PrechargeAll command to the same bank. The following figure shows the optimum time that BankPrecharge/ PrechargeAll command is issued in different CAS# latency. TM Technology Inc. reserves the right P. 8 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK ADDRESS COMMAND TE CH T0 T1 T2 T3 T4 T5 T6 T7 T436432B T8 Bank, Col A Bank(s) Bank, Row tRP READ A NOP NOP NOP Precharge NOP NOP Activate NOP CAS# latency=2 tCK2, DQ's CAS# latency=3 tCK3, DQ's DOUT A0 DOUT A1 DOUT A2 DOUT A3 DOUT A0 DOUT A1 DOUT A2 DOUT A3 Read to Precharge (CAS# Latency = 2, 3) 5 Read and AutoPrecharge command (RAS# = "H", CAS# = "L", WE# = "H", BS = Bank, A10 = "H", A0-A7 = Column Address) The Read and AutoPrecharge command automatically performs the precharge operation after the read operation. Once this command is given, any subsequent command cannot occur within a time delay of {tRP(min.) + burst length}. At full-page burst, only the read operation is performed in this command and the auto precharge function is ignored. Write command (RAS# = "H", CAS# = "L", WE# = "L", BS = Bank, A10 = "L", A0-A7 = Column Address) The Write command is used to write a burst of data on consecutive clock cycles from an active row in an active bank. The bank must be active for at least tRCD(min.) before the Write command is issued. During write bursts, the first valid data-in element will be registered coincident with the Write command. Subsequent data elements will be registered on each successive positive clock edge (refer to the following figure). The DQs remain with high-impedance at the end of the burst unless another command is initiated. The burst length and burst sequence are determined by the mode register, which is already programmed. A full-page burst will continue until terminated (at the end of the page it will wrap to column 0 and continue). T0 CLK T1 T2 T3 T4 T5 T6 T7 T8 6 COM MAND NOP WRITE A NOP NOP NOP NOP NOP NOP NOP DQ0 - DQ3 DIN A0 DIN A1 DIN A2 DIN A3 don't care The first data element and the write are registered on the same clock edge. Extra data is masked. Burst Write Operation (Burst Length = 4, CAS# Latency = 1, 2, 3) A write burst without the AutoPrecharge function may be interrupted by a subsequent Write, BankPrecharge/PrechargeAll, or Read command before the end of the burst length. An interrupt coming from Write command can occur on any clock cycle following the previous Write command (refer to the following figure). TM Technology Inc. reserves the right P. 9 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK COM M AND DQ's TE CH T0 T1 T2 T3 T4 T5 T6 T7 T436432B T8 NOP WRITE A WRITE B NOP NOP NOP NOP NOP NOP 1 Clk Interval DIN A0 DIN B0 DIN B 1 DIN B2 DIN B3 Write Interrupted by a Write (Burst Length = 4, CAS# Latency = 1, 2, 3) The Read command that interrupts a write burst without auto precharge function should be issued one cycle after the clock edge in which the last data-in element is registered. In order to avoid data contention, input data must be removed from the DQs at least one clock cycle before the first read data appears on the outputs (refer to the following figure). Once the Read command is registered, the data inputs will be ignored and writes will not be executed. T0 CL K T1 T2 T3 T4 T5 T6 T7 T8 COM MA ND NOP WRITE A READ B NOP NOP NOP NOP NOP NOP CAS# latency=2 tCK2 , DQ's CAS# latency=3 tCK3 , DQ's DIN A 0 don't care DOUT B 0 DOUT B 1 DOUT B 2 DOUT B 3 DIN A 0 don't care don't care DOUT B 0 DOUT B 1 DOUT B 2 DOUT B 3 Input data for the write is masked. Input data must be removed from the DQ's at least one clock cycle before the Read data appears on the outputs to avoid data contention. Write Interrupted by a Read (Burst Length = 4, CAS# Latency = 2, 3) The BankPrecharge/PrechargeAll command that interrupts a write burst without the auto precharge function should be issued m cycles after the clock edge in which the last data-in element is registered, where m equals tWR/tCK rounded up to the next whole number. In addition, the DQM signals must be used to mask input data, starting with the clock edge following the last data-in element and ending with the clock edge on which the BankPrecharge/PrechargeAll command is entered (refer to the following figure). T0 CLK T1 T2 T3 T4 T5 T6 D QM tRP C OM M A ND WRITE NOP Precharge NOP NOP Activate NOP ADDRESS BA NK COL n DIN n DI N n+ 1 BANK (S) tWR ROW DQ : don't care Note: The DQMs can remain low in this example if the length of the write burst is 1 or 2. Write to Precharge TM Technology Inc. reserves the right P. 10 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm 7 CLK COMMAND TE CH T436432B Write and AutoPrecharge command (refer to the following figure) (RAS# = "H", CAS# = "L", WE# = "L", BS = Bank, A10 = "H", A0-A7 = Column Address) The Write and AutoPrecharge command performs the precharge operation automatically after the write operation. Once this command is given, any subsequent command can not occur within a time delay of {(burst length -1) + tWR + tRP(min.)}. At full-page burst, only the write operation is performed in this command and the auto precharge function is ignored. T0 T1 T2 T3 T4 T5 T6 T7 T8 Bank A Activate NOP NOP AutoPrecharge Write A NOP NOP NOP NOP NOP tDAL CAS# latency=2 tCK2, DQ's CAS# latency=3 tCK3, DQ's DIN A0 DIN A1 * tDAL DIN A0 DIN A1 tDAL= tWR + tRP * * Begin AutoPrecharge Bank can be reactivated at completion of tDAL Burst Write with Auto-Precharge (Burst Length = 2, CAS# Latency = 2, 3) 8 Mode Register Set command (RAS# = "L", CAS# = "L", WE# = "L", BS0,1 and A10-A0 = Register Data) The mode register stores the data for controlling the various operating modes of SDRAM. The Mode Register Set command programs the values of CAS# latency, Addressing Mode and Burst Length in the Mode register to make SDRAM useful for a variety of different applications. The default values of the Mode Register after power-up are undefined; therefore this command must be issued at the power-up sequence. The state of pins BS0,1 and A10~A0 in the same cycle is the data written to the mode register. One clock cycle is required to complete the write in the mode register (refer to the following figure). The contents of the mode register can be changed using the same command and the clock cycle requirements during operation as long as all banks are in the idle state. TM Technology Inc. reserves the right P. 11 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK CKE CS# TE CH T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T436432B T10 tCK2 Clock min. RAS# CAS# WE# Address Key ADDR. DQM tRP DQ Hi-Z PrechargeAll Mode Register Set Command Any Command Mode Register Set Cycle (CAS# Latency = 2, 3) The mode register is divided into various fields depending on functionality. Address BS0,1 A10/AP RFU* A9 WBL A8 A7 A6 A5 A4 A3 BT A2 A1 Burst Length A0 Function RFU* Test Mode CAS Latency *Note: RFU (Reserved for future use) should stay “0” during MRS cycle. • Burst Length Field (A2~A0) This field specifies the data length of column access using the A2~A0 pins and selects the Burst Length to be 2, 4, 8, or full page. A2 0 0 0 0 1 1 1 1 A1 0 0 1 1 0 0 1 1 A0 0 1 0 1 0 1 0 1 Burst Length 1 2 4 8 Reserved Reserved Reserved Full Page TM Technology Inc. reserves the right P. 12 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B • Burst Type Field (A3) The Burst Type can be one of two modes, Interleave Mode or Sequential Mode. A3 0 1 Burst Type Sequential Interleave --- Addressing Sequence of Sequential Mode An internal column address is performed by increasing the address from the column address which is input to the device. The internal column address is varied by the Burst Length as shown in the following table. When the value of column address, (n + m), in the table is larger than 255, only the least significant 8 bits are effective. Data n Column Address 0 n 1 n+1 2 n+2 3 n+3 4 n+4 5 n+5 6 n+6 7 n+7 - 255 N+255 256 n 257 n+1 - 2 words: Burst Length 4 words: 8 words: Full Page: Column address is repeated until terminated. --- Addressing Sequence of Interleave Mode A column access is started in the input column address and is performed by inverting the address bits in the sequence shown in the following table. Data n Data 0 Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 A7 A7 A7 A7 A7 A7 A7 A7 A6 A6 A6 A6 A6 A6 A6 A6 A5 A5 A5 A5 A5 A5 A5 A5 A4 A4 A4 A4 A4 A4 A4 A4 Column Address A3 A3 A3 A3 A3 A3 A3 A3 A2 A2 A2 A2 A2# A2# A2# A2# A1 A1 A1# A1# A1 A1 A1# A1# A0 A0# A0 A0# A0 A0# A0 A0# 8 words 4 words Burst Length • CAS# Latency Field (A6~A4) This field specifies the number of clock cycles from the assertion of the Read command to the first read data. The minimum whole value of CAS# Latency depends on the frequency of CLK. The minimum whole value satisfying the following formula must be programmed into this field. tCAC(min) ≤ CAS# Latency X tCK A6 0 0 0 0 1 A5 0 0 1 1 X A4 0 1 0 1 X CAS# Latency Reserved Reserved 2 clocks 3 clocks Reserved TM Technology Inc. reserves the right P. 13 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B • Test Mode field (A8~A7) These two bits are used to enter the test mode and must be programmed to "00" in normal operation. A8 0 0 1 A7 0 1 X Test Mode normal mode Vendor Use Only Vendor Use Only • Write Burst Length (A9) This bit is used to select the burst write length. A9 0 1 9 Write Burst Length Burst Single Bit No-Operation command (RAS# = "H", CAS# = "H", WE# = "H") The No-Operation command is used to perform a NOP to the SDRAM which is selected (CS# is Low). This prevents unwanted commands from being registered during idle or wait states. 10 Burst Stop command (RAS# = "H", CAS# = "H", WE# = "L") The Burst Stop command is used to terminate either fixed-length or full-page bursts. This command is only effective in a read/write burst without the auto precharge function. The terminated read burst ends after a delay equal to the CAS# latency (refer to the following figure). The termination of a write burst is shown in the following figure. T0 T1 T2 T3 T4 T5 T6 T7 T8 CLK COMMAND READ A NOP NOP NOP Burst Stop NOP NOP NOP NOP The burst ends after a delay equal to the CAS# latency. CAS# latency=2 tCK2, DQ's CAS# latency=3 tCK3, DQ's DOUT A0 DOUT A1 DOUT A2 DOUT A3 DOUT A0 DOUT A1 DOUT A2 DOUT A3 Termination of a Burst Read Operation (Burst Length • 4, CAS# Latency = 2, 3) T0 CLK T1 T2 T3 T4 T5 T6 T7 T8 COMMAND NOP WRITE A NOP NOP Burst Stop NOP NOP NOP NOP CAS# latency= 2, 3 DQ's DIN A0 DIN A1 DIN A2 don't care Input data for the Write is masked. Termination of a Burst Write Operation (Burst Length = X, CAS# Latency = 1, 2, 3) TM Technology Inc. reserves the right P. 14 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm 11 12 TE CH T436432B Device Deselect command (CS# = "H") The Device Deselect command disables the command decoder so that the RAS#, CAS#, WE# and Address inputs are ignored, regardless of whether the CLK is enabled. This command is similar to the No Operation command. AutoRefresh command (RAS# = "L", CAS# = "L", WE# = "H",CKE = "H", BS0,1 = “Don‘t care, A0-A10 = Don't care) The AutoRefresh command is used during normal operation of the SDRAM and is analogous to CAS#before-RAS# (CBR) Refresh in conventional DRAMs. This command is non-persistent, so it must be issued each time a refresh is required. The addressing is generated by the internal refresh controller. This makes the address bits a "don't care" during an AutoRefresh command. The internal refresh counter increments automatically on every auto refresh cycle to all of the rows. The refresh operation must be performed 4096 times within 64ms. The time required to complete the auto refresh operation is specified by tRC(min.). To provide the AutoRefresh command, all banks need to be in the idle state and the device must not be in power down mode (CKE is high in the previous cycle). This command must be followed by NOPs until the auto refresh operation is completed. The precharge time requirement, tRP(min), must be met before successive auto refresh operations are performed. SelfRefresh Entry command (RAS# = "L", CAS# = "L", WE# = "H", CKE = "L", A0-A10 = Don't care) The SelfRefresh is another refresh mode available in the SDRAM. It is the preferred refresh mode for data retention and low power operation. Once the SelfRefresh command is registered, all the inputs to the SDRAM become "don't care" with the exception of CKE, which must remain LOW. The refresh addressing and timing is internally generated to reduce power consumption. The SDRAM may remain in SelfRefresh mode for an indefinite period. The SelfRefresh mode is exited by restarting the external clock and then asserting HIGH on CKE (SelfRefresh Exit command). SelfRefresh Exit command (CKE = "H", CS# = "H" or CKE = "H", RAS# = "H", CAS# = "H", WE# = "H") This command is used to exit from the SelfRefresh mode. Once this command is registered, NOP or Device Deselect commands must be issued for tRC(min.) because time is required for the completion of any bank currently being internally refreshed. If auto refresh cycles in bursts are performed during normal operation, a burst of 4096 auto refresh cycles should be completed just prior to entering and just after exiting the SelfRefresh mode. 13 14 15 Clock Suspend Mode Entry / PowerDown Mode Entry command (CKE = "L") When the SDRAM is operating the burst cycle, the internal CLK is suspended(masked) from the subsequent cycle by issuing this command (asserting CKE "LOW"). The device operation is held intact while CLK is suspended. On the other hand, when all banks are in the idle state, this command performs entry into the PowerDown mode. All input and output buffers (except the CKE buffer) are turned off in the PowerDown mode. The device may not remain in the Clock Suspend or PowerDown state longer than the refresh period (64ms) since the command does not perform any refresh operations. Clock Suspend Mode Exit / PowerDown Mode Exit command When the internal CLK has been suspended, the operation of the internal CLK is reinitiated from the subsequent cycle by providing this command (asserting CKE "HIGH"). When the device is in the PowerDown mode, the device exits this mode and all disabled buffers are turned on to the active state. tPDE(min.) is required when the device exits from the PowerDown mode. Any subsequent commands can be issued after one clock cycle from the end of this command. Data Write / Output Enable, Data Mask / Output Disable command (DQM = "L", "H") During a write cycle, the DQM signal functions as a Data Mask and can control every word of the input data. During a read cycle, the DQM functions as the controller of output buffers. DQM is also used for device selection, byte selection and bus control in a memory system. 16 17 TM Technology Inc. reserves the right P. 15 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm Symbol VIN, VOUT VDD, VDDQ TOPR TSTG TSOLDER PD IOUT TE CH T436432B Absolute Maximum Rating Item Input, Output Voltage Power Supply Voltage Operating Temperature Storage Temperature Soldering Temperature (10s) Power Dissipation Short Circuit Output Current 240 1 50 Leaded Package Lead Free Package Unit V V °C °C Note 1 1 1 1 1 1 1 -1~4.6 - 1~4.6 0~70 - 55~150 260 °C W mA Recommended D.C. Operating Conditions (Ta = 0~70°C) Symbol VDD VDDQ VIH VIL Parameter Power Supply Voltage Power Supply Voltage(for I/O Buffer) LVTTL Input High Voltage LVTTL Input Low Voltage Min. 3.0 3.0 2.0 - 0.3 Typ. 3.3 3.3 Max. 3.6 3.6 VDDQ + 0.3 0.8 Unit V V V V Note 2 2 2 2 Capacitance (VDD = 3.3V, f = 1MHz, Ta = 25°C) Symbol CI CI/O Parameter Input Capacitance Input/Output Capacitance Min. Max. 4.5 6.5 Unit pF pF Note: These parameters are periodically sampled and are not 100% TM Technology Inc. reserves the right P. 16 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Recommended D.C. Operating Conditions (VDD = 3.3V ± 0.3V, Ta = 0~70°C) Description/Test condition Operating Current 1 bank tRC ≥ tRC(min), Outputs Open, Input operation signal one transition per one cycle Precharge Standby Current in power down mode tCK = 15ns, CKE ≤ VIL(max) Precharge Standby Current in power down mode tCK = ∞, CKE ≤ VIL(max) Precharge Standby Current in non-power down mode tCK = 15ns, CS# ≥ VIH(min), CKE ≥ VIH Input signals are changed once during 30ns. Precharge Standby Current in non-power down mode tCK = ∞, CLK ≤ VIL(max), CKE ≥ VIH Active Standby Current in power down mode CKE ≤ VIL(max), tCK = 15ns Active Standby Current in power down mode CKE & CLK ≤ VIL(max), tCK = ∞ Active Standby Current in non-power down mode CKE ≥ VIH(min), CS# ≥ VIH(min), tCK = 15ns Active Standby Current in non-power down mode CKE ≥ VIH(min), CLK ≤ VIL(max), tCK = ∞ Operating Current (Burst mode) tCK =tCK(min), Outputs Open, Multi-bank interleave Refresh Current tRC ≥ TrC(min) Self Refresh Current CKE ≤ 0.2V Symbol ICC1 - 5/5.5/6/7/8/10 Max. Unit Note 200/190/180/155/135/120 3 ICC2P ICC2PS ICC2N ICC2NS ICC3P ICC3PS ICC3N ICC3NS ICC4 ICC5 ICC6 3 3 25 15 5 5 40 30 225/215//200/180/150/130 260/240/220/210/190/180 2 mA 3 3 3 3 3, 4 3 Parameter IIL VOH VOL Description Input Leakage Current ( 0V•VIN•VDD, All other pins not under test = 0V ) LVTTL Output "H" Level Voltage ( IOUT = -2mA ) LVTTL Output "L" Level Voltage ( IOUT = 2mA ) Min. - 1.5 2.4 - Max. 1.5 0.4 Unit uA V V Note TM Technology Inc. reserves the right P. 17 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm Symbol TE CH T436432B Electrical Characteristics and Recommended A.C. Operating Conditions (VDD = 3.3V ± 0.3V, Ta = 0~70°C) (Note: 5, 6, 7, 8) - 5/5.5/6/7/8/10 A.C. Parameter Min. Max. Unit Note tRC tRRD tRCD tRP tRAS tCK2 tCK3 tAC2 tAC3 tOH tCH tCL tIS tIH tLZ tHZ2 tHZ3 tWR tCCD tMRS Row cycle time (same bank) Row activate to row activate delay (different banks) RAS# to CAS# delay (same bank) Precharge to refresh/row activate command (same bank) Row activate to precharge time (same bank) Clock cycle time CL* = 2 CL* = 3 Access time from CLK (positive edge) Data output hold time Clock high time Clock low time Data/Address/Control Input set-up time Data/Address/Control Input hold time Data output low impedance Data output high impedance Write recovery time CAS# to CAS# Delay time Mode Register Set cycle time CL* = 2 CL* = 3 CL* = 2 CL* = 3 55/55/60/70/80/100 10/11/12/14/16/20 18/18/18/21/24/30 15/16.5/18/21/24/30 35/38.5/42/49/56/70 -/-/10/10/ - / 5/5.5/6/7/8/10 -/-/6/6/-/4.5/5/5.5/5.5/6/6 2/2/2/2.5/2.5/2.5 2/2/2.5/3/3/3.5 2/2/2.5/3/3/3.5 1.5/1.5/1.5/1.75/2/2.5 1 1 -/-/6/6/-/4.5/5/5.5/5.5/6/6 2 2/1/1/1/1/1 2 CLK ns 100,000 9 9 9 9 9 9 9 10 10 10 10 9 8 * CL is CAS# Latency. Note: 1. Stress greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. 2. All voltages are referenced to VSS. VIL(Max) = VDDQ+1.0V for pulse width < 2ns. VIL(Min) = -1.0V for pulse width < 2.0ns 3. These parameters depend on the cycle rate and these values are measured by the cycle rate under the minimum value of tCK and tRC. Input signals are changed one time during tCK. 4. These parameters depend on the output loading. Specified values are obtained with the output open. 5. Power-up sequence is described in Note 11. TM Technology Inc. reserves the right P. 18 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B 6. A.C. Test Conditions LVTTL Interface Reference Level of Output Signals Output Load Input Signal Levels Transition Time (Rise and Fall) of Input Signals Reference Level of Input Signals 3 .3V 1.2k Ω 1.4V / 1.4V Reference to the Under Output Load (B) 2.4V / 0.4V 1ns 1.4V 1 .4V 50Ω Z0= 5 0 Ω Output 30pF 870 Ω Output 30pF LVTTL D.C. Test Load (A) LVTTL A.C. Test Load (B) 7. Transition times are measured between VIH and VIL. Transition(rise and fall) of input signals are in a fixed slope (1 ns). 8. tHZ defines the time in which the outputs achieve the open circuit condition and are not at reference levels. 9. If clock rising time is longer than 1 ns, ( tR / 2 -0.5) ns should be added to the parameter. 10. Assumed input rise and fall time tT ( tR & tF ) = 1 ns If tR or tF is longer than 1 ns, transient time compensation should be considered, i.e., [(tr + tf)/2 - 1] ns should be added to the parameter. 11. Power up Sequence Power up must be performed in the following sequence. 1) Power must be applied to VDD and VDDQ(simultaneously) when all input signals are held "NOP" state and both CKE = "H" and DQM = "H." The CLK signals must be started at the same time. 2) After power-up, a pause of 200 seconds minimum is required. Then, it is recommended that DQM is held "HIGH" (VDD levels) to ensure DQ output is in high impedance. 3) All banks must be precharged. 4) Mode Register Set command must be asserted to initialize the Mode register. 5) A minimum of 2 Auto-Refresh dummy cycles must be required to stabilize the internal circuitry of the device. TM Technology Inc. reserves the right P. 19 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Timing Waveforms Figure 1. AC Parameters for Write Timing (Burst Length=4, CAS# Latency=2) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCH CKE tCL t IS t IS t IH tCK2 Begin AutoPrecharge Bank A Begin AutoPrecharge Bank B t IS CS# RAS# CAS# WE# BS0,1 t IS ADDR. RBx t IH CAx RBx CBx RAy CAy RAz RBy DQM tRCD Hi-Z tRC Ax0 Ax1 Ax2 Ax3 tDAL Bx0 Bx1 Bx2 t IS Bx3 Ay0 t IH Ay1 Ay2 t WR tRP Ay3 tRRD DQ Activate Write with Activate Write with Activate Command AutoPrecharge Command AutoPrecharge Command Bank A Command Bank B Command Bank A Bank A Bank B Write Command Bank A Precharge Activate Command Command Bank A Bank A Activate Command Bank B TM Technology Inc. reserves the right P. 20 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 2. AC Parameters for Read Timing (Burst Length=2, CAS# Latency=2) T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 tCH tCL CKE tCK2 t IS Begin AutoPrecharge Bank B t IS CS# RAS# tIH t IH CAS# WE# BS0,1 t IH A10 RAx RBx RAy t IS A0-A11 RAx CAx RBx CBx RAy tRRD tRAS DQM Hi-Z DQ tRC tRCD tAC2 t LZ tAC2 Ax0 t HZ Ax1 Bx0 tRP Bx1 t OH Activate Command Bank A Read Command Bank A Activate Command Bank B Read with Auto Precharge Command Bank B Precharge Command Bank A tHZ Activate Command Bank A TM Technology Inc. reserves the right P. 21 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 3. Auto Refresh (CBR) (Burst Length=4, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx A0-A9 RAx CAx DQM tRP tRC tRC DQ Read Command Bank A Ax0 Ax1 Ax2 Ax3 PrechargeAll Command AutoRefresh Command AutoRefresh Command Activate Command Bank A TM Technology Inc. reserves the right P. 22 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 4. Power on Sequence and Auto Refresh (CBR) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE High level is reauired Minimum of 2 Refresh Cycles are required CS# RAS# CAS# WE# BS0,1 A10 Address Key A0-A9 DQM tRP DQ Hi-Z tRC PrechargeALL Command Inputs must be stable for 200 µs 1st AutoRefresh Command Mode Register Set Command 2nd Auto Refresh Command Any Command TM Technology Inc. reserves the right P. 23 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm T0 TE CH T436432B Figure 5. Self Refresh Entry & Exit Cycle T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 CLK *Note 2 *Note 1 *Note 4 *Note 3 *Note 5 *Note 6 tRC(min) tSRX *Note 7 CKE tPDE t IS CS# RAS# *Note 8 *Note 8 CAS# BS0,1 A0-A9 WE# DQM DQ Hi-Z Hi-Z Self Refresh Enter SelfRefresh Exit AutoRefresh Note: To Enter SelfRefresh Mode 1. CS#, RAS# & CAS# with CKE should be low at the same clock cycle. 2. After 1 clock cycle, all the inputs including the system clock can be don't care except for CKE. 3. The device remains in SelfRefresh mode as long as CKE stays "low". 4. Once the device enters SelfRefresh mode, minimum tRAS is required before exit from SelfRefresh. 5. 6. 7. 8. 9. To Exit SelfRefresh Mode System clock restart and be stable before returning CKE high. Enable CKE and CKE should be set high for minimum time of tSRX. CS# starts from high. Minimum tRC is required after CKE going high to complete SelfRefresh exit. 4096 cycles of burst AutoRefresh is required before SelfRefresh entry and after SelfRefresh exit if the uses burst refresh. system TM Technology Inc. reserves the right P. 24 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 6.1. Clock Suspension During Burst Read (Using CKE) (Burst Length=4, CAS# Latency=1) T0 T 1 T2 T3 T4 T5 T6 T 7 T8 T9 T10 T 11 T1 T13 T14 T15 T16 T17 T1 T19 T20 T21 T22 tCK1 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx A0-A9 RAx CAx DQM t HZ DQ Hi-Z Ax3 Ax0 Ax1 Ax2 Activate Command Bank A Read Command Bank A Clock Suspend 1 Cycle Clock Suspend 2 Cycles Clock Suspend 3 Cycles Note: CKE to CLK disable/enable = 1 clock TM Technology Inc. reserves the right P. 25 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 6.2. Clock Suspension During Burst Read (Using CKE) (Burst Length=4, CAS# Latency=2) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx A0-A9 RAx CAx DQM t HZ DQHi-Z Ax0 Ax1 Ax2 Ax3 Activate Command Bank A Read Command Bank A Clock Suspend 1 Cycle Clock Suspend 2 Cycles Clock Suspend 3 Cycles Note: CKE to CLK disable/enable = 1 clock TM Technology Inc. reserves the right P. 26 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 6.3. Clock Suspension During Burst Read (Using CKE) (Burst Length=4, CAS# Latency=3) T0 CLK T 1 T 2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx A0-A9 RAx CAx DQM tHZ DQ Hi-Z Ax0 Ax1 Ax2 Ax3 Activate Command Bank A Read Command Bank A Clock Suspend Clock Suspend 1 Cycle 2 Cycles Clock Suspend 3 Cycles Note: CKE to CLK disable/enable = 1 clock TM Technology Inc. reserves the right P. 27 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 7.1. Clock Suspension During Burst Write (Using CKE) (Burst Length = 4, CAS# Latency = 1) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx A0-A9 RAx CAx DQM DQ Hi-Z DAx0 DAx1 DAx2 DAx3 Activate Clock Suspend Command 1 Cycle Bank A Write Command Bank A Clock Suspend 2 Cycles Clock Suspend 3 Cycles Note: CKE to CLK disable/enable = 1 clock TM Technology Inc. reserves the right P. 28 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 7.2. Clock Suspension During Burst Write (Using CKE) (Burst Length=4, CAS# Latency=2) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE CS# RAS# CAS# WE# BA0,1 A10 RAx A0-A9 RAx CAx DQM DQHi-Z DAx0 DAx1 DAx2 DAx3 Activate Command Bank A Clock Suspend Clock Suspend 1 Cycle 2 Cycles Write Command Bank A Clock Suspend 3 Cycles Note: CKE to CLK disable/enable = 1 clock TM Technology Inc. reserves the right P. 29 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 7.3. Clock Suspension During Burst Write (Using CKE) (Burst Length=4, CAS# Latency=3) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx A0-A9 RAx CAx DQM DQ Hi-Z DAx0 DAx1 DAx2 DAx3 Activate Command Bank A Clock Suspend Clock Suspend 1 Cycle 2 Cycles Write Command Bank A Clock Suspend 3 Cycles Note: CKE to CLK disable/enable = 1 clock TM Technology Inc. reserves the right P. 30 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 8. Power Down Mode and Clock Mask (Burst Length=4, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE t IS tPDE Valid CS# RAS# CAS# WE# BS0,1 A10 RAx A0~A9 RAx CAx DQM tHZ Hi-Z DQ ACTIVE STANDBY Activate Read Command Command Bank A Bank A Power Down Power Down Mode Entry Mode Exit Ax0 Ax1 Ax2 Ax3 PRECHARGE STANDBY Clock Mask Start Clock Mask End Precharge Command Bank A Power Down Mode Entry Power Down Mode Exit Any Command TM Technology Inc. reserves the right P. 31 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 9.1. Random Column Read (Page within same Bank) (Burst Length=4, CAS# Latency=1) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE CS# RAS# CAS# WE# BA0,1 A10 RAw RAz A0~A9 RAw CAw CAx CAy RAz CAz DQM DQHi-Z Aw0 Aw1 Aw2 Aw3Ax0 Ax1 Ay0 Ay1Ay2 Ay3 Az0 Az1Az2 Az3 Activate Command Bank A Read Command Bank A Read Command Bank A Read Command Bank A Precharge Read Command Command Bank A Bank A Activate Command Bank A TM Technology Inc. reserves the right P. 32 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 9.2. Random Column Read (Page within same Bank) (Burst Length=4, CAS# Latency=2) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE CS# RAS# CAS# WE# BA0,1 A10 RAw RAz A0~A9 RAw CAw CAx CAy RAz CAz DQM DQHi-Z Aw0 Aw1 Aw2 Aw3 Ax0 Ax1 Ay0 Ay1 Ay2 Ay3 Az0 Az1 Az2 Az3 Activate Command Bank A Read Command Bank A Read Command Bank A Read Command Bank A Precharge Activate Command Command Bank A Bank A Read Command Bank A TM Technology Inc. reserves the right P. 33 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 9.3. Random Column Read (Page within same Bank) (Burst Length=4, CAS# Latency=3) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE CS# RAS# CAS# WE# BS0,1 A10 RAw RAz A0~A9 RAw CAw CAx CAy RAz CAz DQM DQHi-Z Activate Command Bank A Read Command Bank A Aw0 Aw1 Aw2 Aw3 Ax0 Ax1 Ay0 Az0 Ay1 Ay2 Ay3 Read Command Bank A Read Command Bank A Precharge Command Bank A Activate Command Bank A Read Command Bank A TM Technology Inc. reserves the right P. 34 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 10.1. Random Column Write (Page within same Bank) (Burst Length=4, CAS# Latency=1) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE CS# RAS# CAS# WE# BS0,1 A10 RBw RBz A0~A9 RBw CBw CBx CBy RBz CBz DQM Hi-Z DQ DBw0DBw1DBw2 DBw3 DBx0 DBx1 DBy0 DBy1 DBy2 DBy3 DBz0 DBz1 DBz2 DBz3 Activate Command Bank A Write Command Bank B Write Command Bank A Write Command Bank B Precharge Command Bank B Activate Command Bank B Write Command Bank B TM Technology Inc. reserves the right P. 35 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 10.2. Random Column Write (Page within same Bank) (Burst Length=4, CAS# Latency=2) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE CS# RAS# CAS# WE# BS0,1 A10 RBw RBz A0~A9 RBw CBw CBx CBy RBz CBz DQM DQ Hi-Z DBw0 DBw1 Bw2 DBw3 DBx0 D DBy0 DBy1 DBx1 DBy2 DBy3 DBz0 DBz2 DBz3 DBz1 Activate Command Bank A Write Command Bank B Write Command Bank B Write Command Bank B Precharge Activate Command Command Bank B Bank B Write Command Bank B TM Technology Inc. reserves the right P. 36 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 10.3. Random Column Write (Page within same Bank) (Burst Length=4, CAS# Latency=3) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE CS# RAS# CAS# WE# BS0,1 A10 RBw RBz A0~A9 RBw CBw CBx CBy RBz CBz DQM DQ Hi-Z DBw0 DBw1DBw2 DBw3 DBx0 DBx1 DBy0 DBy1 DBy2 DBy3 DBz0 DBz1 DBz2 Activate Command Bank A Write Command Bank B Write Command Bank B Write Command Bank B Precharge Command Bank B Activate Command Bank B Write Command Bank B TM Technology Inc. reserves the right P. 37 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 11.1. Random Row Read (Interleaving Banks) (Burst Length=8, CAS# Latency=1) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE High CS# RAS# CAS# WE# BS0,1 A10 RBx RAx RBy A0~A9 RBx CBx RAx CAx RBy CBy tRCD DQM DQHi-Z Bx0 Bx1 Bx2 Bx3 Bx4 Bx5 Bx6 Bx7 Ax0 Ax1 Ax2 Ax3 Ax4 Ax5 Ax6 Ax7 By0 By1 By2 tAC1 tRP Activate Command Bank B Read Command Bank B Activate Command Bank A Precharge Command Bank B Activate Read Command Command Bank B Bank A Read Command Bank B Precharge Command Bank A TM Technology Inc. reserves the right P. 38 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 11.2. Random Row Read (Interleaving Banks) (Burst Length=8, CAS# Latency=2) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE High CS# RAS# CAS# WE# BS0,1 A10 RBx RAx RBy A0~A9 RBx CBx RAx CAx RBy CBy tRCD DQM tAC2 tRP Hi-Z DQ Bx0 Bx1 Bx2 Bx3 Bx4 Bx5 Bx6 Bx7 Ax0 Ax1 Ax2 Ax3 Ax4 Ax5 Ax6 Ax7 By0 By1 Activate Command Bank B Read Command Bank B Activate Command Bank A Precharge Command Bank B Read Command Bank A Activate Command Bank B Read Command Bank B TM Technology Inc. reserves the right P. 39 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 11.3. Random Row Read (Interleaving Banks) (Burst Length=8, CAS# Latency=3) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 High CKE CS# RAS# CAS# WE# BS0,1 A10 RBx RAx RBy A0~A9 RBx CBx RAx CAx RBy CBy tRCD DQM tAC3 tRP Hi-Z DQ Bx0 Bx1 Bx2 Bx3 Bx4 Bx5 Bx6 Ax7 Bx7 Ax0 Ax1 Ax2 Ax3 Ax4 Ax5 Ax6 By0 Activate Command Bank B Read Command Bank B Activate Command Bank A Read Command Bank A Precharge Command Bank B Activate Command Bank B Read Command Bank B Precharge Command Bank A TM Technology Inc. reserves the right P. 40 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 12.1. Random Row Write (Interleaving Banks) (Burst Length=8, CAS# Latency=1) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RAy A0~A9 RAx CAx RBx CBx RAy CAy tRCD DQM tRP tWR DQ Hi-Z DAx0 DAx1 DAx2 DAx3 DAx4 DAx5DAx6 DAx7 DBx0 DBx1 DBx2 DBx3 DBx4 DBx5 DBx6 DBx7 DAy0 DAy1 DAy2 DAy3 Activate Command Bank A Write Command Bank A Activate Command Bank B Write Command Bank B Precharge Command Bank A Activate Command Bank A Precharge Command Bank B Write Command Bank A TM Technology Inc. reserves the right P. 41 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 12.2. Random Row Write (Interleaving Banks) (Burst Length=8, CAS# Latency=2) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RAy A0~A9 RAx CAx RBx CBx RAy CAy tRCD DQM tWR* tRP tWR* DQ Hi-Z DAx0 DAx1 DAx2 DAx3 DAx4DAx5 DAx6 DAx7 DBx0 DBx1 DBx2 DBx3 DBx4DBx5 DBx6 DBx7 DAy0 DAy1DAy2 DAy3 DAy4 Activate Write Command Command Bank A Bank A Activate Command Bank B Write Command Bank B Precharge Command Bank A Activate Command Bank A Write Command Bank A Precharge Command Bank B * tWR > tWR(min.) TM Technology Inc. reserves the right P. 42 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 12.3. Random Row Write (Interleaving Banks) (Burst Length=8, CAS# Latency=3) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RAy A0~A9 RAx CAx RBx CBx RAy CAy tRCD DQM tWR* tRP tWR* Hi-Z DQ DAx0DAx1 DAx2 DAx3DAx4 DAx5 DAx6 DAx7 DBx0 DBx1DBx2 DBx3 DBx4 DBx5 DBx6 DBx7 DAy0 DAy1 DAy2 DAy3 Activate Command Bank A Write Command Bank A Activate Command Bank B Write Command Bank B Precharge Command Bank A Activate Command Bank A Write Command Bank A Precharge Command Bank B * tWR > tWR(min.) TM Technology Inc. reserves the right P. 43 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 13.1. Read and Write Cycle (Burst Length=4, CAS# Latency=1) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx A0~A9 RAx CAx CAy CAz DQM DQ Hi-Z Ax0 Ax1 Ax2 Ax3 DAy0DAy1 DAy3 Az0 Az1 Az3 Activate Command Bank A Read Command Bank A Read The Write Data Write Command is Masked with a Command Bank A Zero Clock Bank A Latency The Read Data is Masked with a Two Clock Latency Precharge Command Bank B TM Technology Inc. reserves the right P. 44 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm T0 CLK TE CH T436432B Figure 13.2. Read and Write Cycle (Burst Length=4, CAS# Latency=2) T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx A0~A9 RAx CAx CAy CAz DQM DQ Hi-Z Ax0 Ax1 Ax2 Ax3 DAy0 DAy1 DAy3 Az0 Az1 Az3 Activate Command Bank A Read Command Bank A Write The Write Data Command is Masked with a Bank A Zero Clock Latency Read Command Bank A The Read Data is Masked with a Two Clock Latency TM Technology Inc. reserves the right P. 45 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 13.3. Read and Write Cycle (Burst Length=4, CAS# Latency=3) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx A0~A9 RAx CAx CAy CAz DQM DQ Hi-Z Ax0 Ax1 Ax2 Ax3 DAy0 DAy1 DAy3 Az0 Az1 Az3 Activate Command Bank A Read Command Bank A Write The Write Data Command is Masked with a Bank A Zero Clock Latency Read Command Bank A The Read Data is Masked with a Two Clock Latency TM Technology Inc. reserves the right P. 46 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 14.1. Interleaving Column Read Cycle (Burst Length=4, CAS# Latency=1) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx RBw A0~A9 RAx RAx RBw CBw CBx CBy CAy CBz DQM DQ Hi-Z tRCD tAC1 Ax0 Ax1 Ax2 Ax3 Bw0 Bw1 Bx0 Bx1 By0 By1 Ay0 Ay1 Bz0 Bz1 Bz2 Bz3 Activate Command Bank A Read Command Bank A Activate Command Bank B Read Command Bank B Read Command Bank B Read Command Bank B Read Command Bank A Read Command Bank B Precharge Command Bank A Precharge Command Bank B TM Technology Inc. reserves the right P. 47 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 14.2. Interleaving Column Read Cycle (Burst Length=4, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx RAx A0~A9 RAx CAy RAx CBw CBx CBy CAy CBz DQM tRCD tAC2 DQ Hi-Z Ax0 Ax1 Ax2 Ax3 Bw0 Bw1 Bx0 Bx1 By0 By1 Ay0 Ay1 Bz0 Bz1 Bz2 Bz3 Activate Command Bank A Read Command Bank A Activate Command Bank B Read Read Command Command Bank B Bank B Read Command Bank B Read Command Bank A Read Command Bank B Precharge Command Bank A Precharge Command Bank B TM Technology Inc. reserves the right P. 48 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 14.3. Interleaved Column Read Cycle (Burst Length=4, CAS# Latency=3) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE CS# RAS# CAS# WE# BS0,1 RAx RBx A10 A0~A9 RAx CAx RBx CBx CBy CBz CAy DQM DQHi-Z tRCD tAC3 Ax0 Ax1 Ax2 Ax3 Bx0 Bx1 By0 By1 Bz0 Bz1 Ay0 Ay1 Ay2 Ay3 Activate Command Bank A Read Command Bank A Activate Command Bank B Read Command Bank B Read Command Bank B Read Command Bank B Read Prechaerge Command Command Bank A Bank B Precharge Command Bank A TM Technology Inc. reserves the right P. 49 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 15.1. Interleaved Column Write Cycle (Burst Length=4, CAS# Latency=1) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx RBw A0~A9 RAx CAx RBw CBw CBx CBy CAy CBz tRP DQM Hi-Z DAx0 DAx1 DAx2 DAx3 DBw0DBw1 DBx0 DBx1 DBy0 DBy1 DAy0 DAy1 DBz0 DBz1 DBz2 DBz3 tRCD tRRD tWR tRP DQ Activate Command Bank A Activate Command Bank B Write Command Bank B Write Command Bank B Write Command Bank B Write Command Bank A Write Command Bank A Write Command Bank B Precharge Command Bank A Precharge Command Bank B TM Technology Inc. reserves the right P. 50 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 15.2. Interleaved Column Write Cycle (Burst Length=4, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx RBw A0~A9 RAx CAx RBw CBw CBx CBy CAy CBz DQM tRCD tRRD tRP tWR tRP DQ Hi-Z DAx0 DAx1 DAx2 DAx3 DBw0 DBw1 DBx0 DBx1DBy0 DBy1DAy0 DAy1 DBz0 DBz1 DBz2 DBz3 Activate Command Bank A Write Command Bank A Activate Command Bank B Write Command Bank B Write Command Bank B Write Command Bank B Write Command Bank A Write Command Bank B Precharge Command Bank A Precharge Command Bank B TM Technology Inc. reserves the right P. 51 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 15.3. Interleaved Column Write Cycle (Burst Length=4, CAS# Latency=3) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx RBw A0~A9 RAx CAx RBw CBw CBx CBy CAy CBz DQM tRCD tRRD > tRRD(min) tWR tRP tWR(min) DQ Hi-Z DAx0 DAx1 DAx2 DAx3 DBw0 DBw1DBx0 DBx1 DBy0 DBy1 DAy0 DAy1 DBz0 DBz1 DBz2 DBz3 Activate Command Bank A Activate Command Bank B Write Command Bank A Write Command Bank B Write Command Bank B Write Command Bank B Write Command Bank A Write Command Bank B Precharge Command Bank A Precharge Command Bank B TM Technology Inc. reserves the right P. 52 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 16.1. Auto Precharge after Read Burst (Burst Length=4, CAS# Latency=1) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE High CS# RAS# CAS# WE# BS0,1 RAx RBy RBz A10 RBx A0~A9 RAx CAx RBx CBx CAy RBy CBy RBz CBz DQM DQ Hi-Z Ax0 Ax1 Ax2 Ax3 Bx0 Bx1 Bx2 Bx3 Ay0 Ay1 Ay2 Ay3 By0 By1 By2 By3 Bz0 Bz1 Bz2 Bz3 Activate Command Bank A Read Command Bank A Activate Command Bank B Read with Auto Precharge Command Bank B Activate Command Bank B Read with Auto Precharge Command Bank A Read with Auto Precharge Command Bank B Activate Command Bank B Read with Auto Precharge Command Bank B TM Technology Inc. reserves the right P. 53 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 16.2. Auto Precharge after Read Burst (Burst Length=4, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBy RAz A0~A9 RAx CAx RBx CBx RAy RBy CBy RAz CAz DQM DQ Hi-Z Ax0 Ax1 Ax2 Ax3 Bx0 Bx1 Bx2 Bx3 Ay0 Ay1 Ay2 Ay3 By0 By1 By2 By3 Az0 Az1 Az2 Activate Command Bank A Read Command Bank A Read with Activate Command Auto Precharge Command Bank B Bank B Read with Activate Read with Activate Read with Auto Precharge Command Auto Precharge Command Auto Precharge Command Bank B Command Bank A Command Bank A Bank B Bank A TM Technology Inc. reserves the right P. 54 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 16.3. Auto Precharge after Read Burst (Burst Length=4, CAS# Latency=3) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBy A0~A9 RAx CAx RBx CBx CAy RBy CBy DQM DQ Hi-Z Ax0 Ax1 Ax2 Ax3 Bx0 Bx1 Bx2 Bx3 Ay0 Ay1 Ay2 Ay3 By0 By1 By2 By3 Activate Command Bank A Activate Command Bank B Read Command Bank A Read with Auto Precharge Command Bank B Read with Auto Precharge Command Bank A Activate Command Bank B Read with Auto Precharge Command Bank B TM Technology Inc. reserves the right P. 55 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 17.1. Auto Precharge after Write Burst (Burst Length=4, CAS# Latency=1) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBy RAz A0~A9 RAx CAx RBx CBx CAy RBy CBy RAz CAz DQM Hi-Z DQ DAx0 DAx1 DAx2 DAx3 DBx0 DBx1 DBx2DBx3 DAy0 DAy1DAy2 DAy3 DBy0 DBy1 DBy2 DBy3 DAz0 DAz0 DAz0 DAz0 Activate Command Bank A Write Command Bank A Activate Write with Command Auto Precharge Bank B Command Bank B Write with Auto Precharge Command Bank A Activate Write with Command Auto Precharge Bank B Command Bank B Activate Command Bank A Write with Auto Precharge Command Bank A TM Technology Inc. reserves the right P. 56 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 17.2. Auto Precharge after Write Burst (Burst Length=4, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBy RAz A0~A9 RAx CAx RBx CBx CAy RBy CBy RAz CAz DQM DQ Hi-Z DAx0 DAx1 DAx2 DAx3 DBx0 DBx1DBx2 DBx3 DAy0 DAy1DAy2 DAy3 DBy0 DBy1 DBy2 DBy3DAz0 DAz1 DAz2 DAz3 Activate Write Command Command Bank A Bank A Activate Write with Command Auto Precharge Bank B Command Bank B Write with Auto Precharge Command Bank A Activate Write with Write with Activate Command Auto Precharge Command Auto Precharge Bank B Command Command Bank A Bank B Bank A TM Technology Inc. reserves the right P. 57 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 17.3. Auto Precharge after Write Burst (Burst Length=4, CAS# Latency=3) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE High CS# RAS# CAS# WE# BS0,1 ` A9 RAx RBx RBy A0~A9 RAx CAx RBx CBx CAy RBy CBy DQM DQHi-Z DAx0 DAx1 DAx2 DAx3 DBx0 DBx1 DBx2 DBx3 DAy0 DAy1 DAy2 DAy3 DBy0 DBy1 DBy2DBy3 Activate Command Bank A Activate Command Bank B Write Command Bank A Write with Auto Precharge Command Bank B Write with Auto Precharge Command Bank A Activate Command Bank B Write with Auto Precharge Command Bank B TM Technology Inc. reserves the right P. 58 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 18.1. Full Page Read Cycle (Burst Length=Full Page, CAS# Latency=1) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBy A0~A9 RAx CAx RBx CBx RBy DQM tRRD tRP Hi-Z DQ Ax Ax+1 Ax+2 Ax-2 Ax-1 Ax Ax+1 Bx Bx+1 Bx+2 Bx+3 Bx+4 Bx+5 Bx+6 Bx+7 Activate Command Bank A Activate Command Bank B The burst counter wraps from the highest order Read page address back to zero Command during this time interval Bank A Read Command Bank B Full Page burst operation does not terminate when the burst length is satisfied; the burst counter increments and continues bursting beginning with the starting address. Precharge Command Bank B Activate Burst Stop Command Command Bank B TM Technology Inc. reserves the right P. 59 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 18.2. Full Page Read Cycle (Burst Length=Full Page, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBy A0~A9 RAx CAx RBx CBx RBy tRP DQM DQHi-Z Ax Ax-2 Ax+1 Ax+2 Ax-1 Ax Ax+1 Bx Bx+1 Bx+2 Bx+3 Bx+4 Bx+5 Bx+6 Activate Command Bank A Read Command Bank A Activate Read Precharge Full Command Command Page burst operation does not Command terminate when the burst length is satisfied; Bank B Bank B Bank B The burst counter wraps the burst counter increments and continues from the highest order bursting beginning with the starting address. page address back to zero Burst Stop during this time interval Command Activate Command Bank B TM Technology Inc. reserves the right P. 60 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 18.3. Full Page Read Cycle (Burst Length=Full Page, CAS# Latency=3) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBy A0~A9 RAx CAx RBx CBx RBy DQM tRP DQ Hi-Z Ax Ax+1 Ax+2 Ax-2 Ax-1 Ax Ax+1 Bx Bx+1 Bx+2 Bx+3 Bx+4 Bx+5 Activate Command Bank A Read Command Bank A Activate Command Bank B Read Command Bank B The burst counter wraps from the highest order page address back to zero during this time interval Precharge Full Page burst operation does not Command terminate when the burst length is Bank B satisfied; the burst counter increments and continues bursting beginning with the Burst Stop starting address. Command Activate Command Bank B TM Technology Inc. reserves the right P. 61 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 19.1. Full Page Write Cycle (Burst Length=Full Page, CAS# Latency=1) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBy A0~A9 DQM RAx CAx RBx CBx RBy DQ Hi-Z DBx DAx DAx+ 1 DAx+ 2 DAx+ 3 DAx- 1 DAx DAx+ 1 DBx+ 1 DBx+ 2 DBx+ 3 DBx+ 4 DBx+ 5 DBx+ 6 DBx+ 7 Activate Command Bank A Activate Command Bank B The burst counter wraps from the highest order Write page address back to zero Command during this time interval Bank A Write Command Bank B Full Page burst operation does not terminate when the burst length is satisfied; the burst counter increments and continues bursting beginning with the starting address. Data is ignored Precharge Command Bank B Burst Stop Activate Command Command Bank B TM Technology Inc. reserves the right P. 62 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 19.2. Full Page Write Cycle (Burst Length=Full Page, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBy A0~A9 RAx CAx RBx CBx RBy DQM DQ Hi-Z DAx DAx+ 1 DAx+ 2 DAx+ 3 DAx- 1 DAx DAx+ 1 DBx DBx+ 1DBx+ 2 DBx+ 3 DBx+ 4 DBx+ 5 DBx+ 6 Activate Command Bank A Write Command Bank A Activate Write Command Command Bank B Bank B The burst counter wraps Full Page burst operation does not terminate when the burst from the highest order page address back to zero length is satisfied; the burst counter increments and continues bursting during this time interval beginning with the starting address. Data is ignored Precharge Command Bank B Burst Stop Command Activate Command Bank B TM Technology Inc. reserves the right P. 63 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 19.3. Full Page Write Cycle (Burst Length=Full Page, CAS# Latency=3) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE High CS# RAS# CAS# WE# BS0,1 A10 A0~A9 RAx RBx RBy RAx CAx RBx CBx RBy DQM Data is ignored DQ Hi-Z DAx DAx+ 1 DAx+ 2 DAx+ 3 DAx- 1 DAx DAx+ 1 DBx DBx+ 1 DBx+ 2 DBx+ 3 DBx+ 4 DBx+ 5 Activate Command Bank A Write Command Bank A Activate Write Command Command Bank B Bank B The burst counter wraps Full Page burst operation does from the highest order page address back to zero not terminate when the burst length is satisfied; the burst counter during this time interval increments and continues bursting beginning with the starting address. Precharge Command Bank B Burst Stop Command Activate Command Bank B TM Technology Inc. reserves the right P. 64 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 20. Byte Write Operation (Burst Length=4, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx A0~A9 RAx CAx CAy CAz LDQM UDQM DQ0 - DQ7 Ax0 Ax1 Ax2 DAy2 DAy1 Az1 Az2 DQ8 - DQ15 Ax1 Ax2 Ax3 DAy0 DAy1 DAy3 Az0 Az1 Az2 Az3 Activate Command Bank A Upper 3 Bytes Read are Command masked Bank A Lower Byte is masked Write Upper 3 Bytes Read Command are masked Command Bank A Bank A Lower Byte is masked Lower Byte is masked TM Technology Inc. reserves the right P. 65 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 21. Random Row Read (Interleaving Banks) (Burst Length=2, CAS# Latency=1) T0 CLK T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE High Begin Auto Precharge Bank B Begin Auto Precharge Bank A Begin Auto Precharge Bank B Begin Auto Precharge Bank A Begin Auto Precharge Bank B Begin Auto Precharge Bank A Begin Auto Precharge Bank B Begin Auto Precharge Bank A Begin Auto Precharge Bank B Begin Auto Precharge Bank A CS# RAS# CAS# WE# BS0,1 A10 A0~A9 RBu RAu RBv RAv RBw RAw RBx RAx RBy RAy RBz RAz RBu CBu RAu CAu RBv CBv RAv CAv RBw CBw RAw CAw RBx CBx RAx CAx RBy CBy RAy CAy RBz CBz RAz DQM tRP tRP tRP tRP tRP tRP tRP tRP tRP tRP DQ Activate Command Bank B Bu0 Bu1 Au0 Au1 Bv0 Bv1 Av0 Av1 Bw0 Bw1 Aw0 Aw1Bx0 Bx1 Ax0 Ax1 By0 By1 Ay0 Ay1 Bz0 Activate Command Bank A Activate Command Bank B Activate Command Bank A Activate Command Bank B Activate Command Bank A Activate Command Bank B Activate Command Bank A Activate Command Bank B Activate Command Bank A Activate Command Bank B Activate Command Bank A Read Bank B with Auto Precharge Read Bank A with Auto Precharge Read Bank B with Auto Precharge Read Bank A with Auto Precharge Read Bank B with Auto Precharge Read Bank A with Auto Precharge Read Bank B with Auto Precharge Read Bank A with Auto Precharge Read Bank B with Auto Precharge Read Bank A with Auto Precharge Read Bank B with Auto Precharge TM Technology Inc. reserves the right P. 66 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 22. Full Page Random Column Read (Burst Length=Full Page, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBw A0~A9 RAx RBx CAx CBx CAy CBy CAz CBz RBw tRP DQM tRRD DQ tRCD Ax0 Bx0 Ay0 Ay1 By0 By1 Az0 Az1 Az2 Bz0 Bz1 Bz2 Activate Command Bank A Activate Command Bank B Read Read Command Command Bank B Read Bank B Command Read Bank A Command Bank A Read Command Bank A Read Command Bank B Precharge Command Bank B (Precharge Temination) Activate Command Bank B TM Technology Inc. reserves the right P. 67 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 23. Full Page Random Column Write (Burst Length=Full Page, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK2 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx RBx RBw A0~A9 RAx RBx CAx CBx CAy CBy CAz CBz RBw tWR DQM tRP tRRD DQ tRCD DAx0DBx0DAy0 DAy1 DBy0 DBy1 DAz0 DAz1 DAz2 DBz0 DBz1 DBz2 Activate Command Bank A Activate Command Bank B Write Command Bank B Write Write Command Command Bank A Bank A Write Command Bank B Write Command Bank A Write Command Bank B Precharge Command Bank B (Precharge Temination) Activate Write Data Command Bank B is masked TM Technology Inc. reserves the right P. 68 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 24.1. Precharge Termination of a Burst (Burst Length=Full Page, CAS# Latency=1) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK1 CKE CS# RAS# CAS# WE# BS0,1 A10 RAx RAy RAz CAy A0~A9 RAx CAx RAy RAz CAz tWR tRP DQM DQ DAx0 DAx1 DAx2 DAx3 DAx4 Ay0 Ay1 Ay2 tRP Precharge Termination of a Read Burst. DAz6 DAz7 DAz0 DAz1 DAz2 DAz3 DAz4 DAz5 Read Activate Precharge Termination Precharge Command Command Command of a Write Burst. Bank A Bank A Write data is masked. Bank A Write Activate Command Command Bank A Bank A Precharge Command Bank A Write Command Bank A Activate Command Bank A TM Technology Inc. reserves the right P. 69 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm TE CH T436432B Figure 24.2. Precharge Termination of a Burst (Burst Length=8 or Full Page, CAS# Latency=2) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 CLK tCK2 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RAy RAz A0~A9 RAx CAx RAy CAy RAz CAz tWR tRP DQM tRP tRP DQ DAx0 DAx1 DAx2 DAx3 Ay0 Ay1 Ay2 Az0 Az1 Az2 Activate Command Bank A Write Precharge Command Command Bank A Bank A Precharge Termination of a Write Burst. Write data is masked. Activate Command Bank A Read Command Bank A Precharge Command Bank A Activate Command Bank A Precharge Read Command Command Bank A Bank A Precharge Termination of a Read Burst TM Technology Inc. reserves the right P. 70 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm CLK TE CH T436432B Figure 24.3. Precharge Termination of a Burst (Burst Length=4, 8 or Full Page, CAS# Latency=3) T0 T 1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T 11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22 tCK3 CKE High CS# RAS# CAS# WE# BS0,1 A10 RAx RAy RAz A0~A9 RAx CAx RAy CAy RAz tWR DQM tRP tRP DQ DAx0 DAx1 Ay0 Ay1 Ay2 Activate Command Bank A Write Command Bank A Write Data is masked Precharge Command Bank A Activate Command Bank A Read Command Bank A Precharge Command Bank A Activate Precharge Termination Command of a Read Burst Bank A Precharge Termination of a Write Burst TM Technology Inc. reserves the right P. 71 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A tm 86 TE CH T436432B 86 Pin TSOP II Package Outline Drawing Information 44 HE E 0.254 θ° L L1 1 D 43 A1 A2 A e S B y L L1 Symbol A A1 A2 B C D E e HE L L1 S y θ Min 0.002 0.037 0.007 0.87 0.395 0.455 0.016 0° Dimension in inch Normal 0.004 0.039 0.008 0.005 0.875 0.400 0.0197 0.463 0.020 0.0315 0.024 - Max 0.047 0.006 0.041 0.009 0.88 0.405 0.471 0.024 0.004 8° Min 0.05 0.95 0.17 22.09 10.03 11.56 0.40 0° Dimension in mm Normal Max 1.20 0.10 0.15 1 1.05 0.2 0.23 0.127 22.22 22.35 10.16 10.29 0.50 11.76 0.50 0.80 0.61 11.96 0.60 0.10 8° Notes : 1. Dimension D&E do not include interlead flash. 2. Dimension B does not include dambar protrusion/intrusion. 3. Dimension S includes end flash. 4. Controlling dimension : mm TM Technology Inc. reserves the right P. 72 to change products or specifications without notice. Publication Date: FEB. 2007 Revision: A C