XC6132C15EMR-G

XC6132 Series ETR02032-002 Delay capacitor adjustable voltage detectors with sense pin isolation, surge voltage protection and HYS external adjustment ■GENERAL DESCRIPTION The XC6132 series are ultra-small delay capacitor adjustable type voltage detectors that have high accuracy and sense pin isolation. High accuracy and a low supply current are achieved by means of a CMOS process, a highly accurate reference power supply, and laser trimming technology. The sense pin is isolated from the power input pin to enable monitoring of the voltage of another power supply. Output can be maintained in the detection state even if the voltage of the power supply that is monitored drops to 0V. The sense pin is also suitable for detecting high voltages, and the detection and release voltage can be set as desired using external resistors. An internal surge voltage protection circuit and an internal delay circuit are also provided. By connecting a capacitor to the Cd/MRB pin, any release delay time and detect delay time can be set and the pin can also be used as a manual reset pin. The HYS external adjustment pin can be used to establish a sufficient hysteresis width. ■FEATURES ■APPLICATIONS ●Microcontroller reset and malfunction monitoring ●Battery voltage monitoring ●System power-on reset ●Power failure detection Operating Ambient Temperature Operating voltage range Detect voltage range Detect voltage accuracy (Ta=25℃) Detect voltage accuracy (Ta=-40～125℃) Temperature Characteristics Hysteresis width Adjustable Pin for Hysteresis Width Low supply current Manual reset function Output type Output logic Delay capacitance pin Sense pin Packages Environment friendly : -40℃～+125℃ : 1.6V～6.0V : 0.8V～2.0V : ±18mV(VDF＜1.5V) : ±1.2%(1.5V≦VDF≦2.0V) : ±36mV(VDF＜1.5V) : ±2.7%(1.5V≦VDF≦2.0V) : ±50ppm/℃(TYP.) : VDF×0.1％(TYP.) : Yes : 1.28μA(TYP.) VIN=1.6V(At detection) : 1.65μA(TYP.) VIN=6.0V(At release) : Yes (For details, refer to FUNCTION CHART) : CMOS or Nch open drain : H level or L level at detection : Release delay / detection delay can be set in 5 time ratio options (For details, refer to Selection Guide). : Includes a surge voltage protection function : USP-6C,SOT-26 : EU RoHS compliant, Pb free ■TYPICAL APPLICATION CIRCUIT ■TYPICAL PERFORMANCE CHARACTERISTICS +B VDD VIN=3.3V VSEN=0V→10V→0V R2=100kΩ、R3=330kΩ XC6132C10E R3 R1 HYS VIN 4.0 Rpull(*1) 3.5 RESET RESETB R2 GND RESET SW Cd Cd/MRB VSS Battery (+B) voltage monitoring: Detects high voltage via R1/R2 resistance division. A hysteresis width can be added as desired by connecting R3 between the VSEN and HYS pins Output Voltage : VRESET(V) VSEN 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0 1 2 3 4 5 6 7 8 9 10 Voltage Sense : VSEN(V) OPEN R1=330kΩ R1=560kΩ (For details, refer to OPERATIONAL DESCRIPTION). 1/30 XC6132 Series ■BLOCK DIAGRAMS (1)XC6132C Series A/B/C/D/L type (RESET OUTPUT: CMOS/Active High) VSEN HYS VIN M3 RSEN=RA+RB+RC M5 M7 + RA - SURGE VOLTAGE PROTECT BLOCK Rp VREF M1 M4 RB Rn DELAY/ MRB CONTROL BLOCK RESET M6 Cd/MRB RC M2 VSS * Diodes inside the circuit are an ESD protection diode and a parasitic diode. (2)XC6132C Series E/F/H/K/M type (RESETB OUTPUT: CMOS/Active Low) HYS VSEN VIN M3 RSEN=RA+RB+RC M5 M7 + RA M1 - SURGE VOLTAGE PROTECT BLOCK Rp VREF M4 RB Rn DELAY/ MRB CONTROL BLOCK RESETB M6 Cd/MRB RC M2 VSS * Diodes inside the circuit are an ESD protection diode and a parasitic diode. 2/30 XC6132 Series ■BLOCK DIAGRAMS (Continued) (3)XC6132N Series A/B/C/D/L type (RESET OUTPUT: Nch open drain/Active High) VSEN HYS VIN M3 RSEN=RA+RB+RC M5 Rp + RA - SURGE VOLTAGE PROTECT BLOCK VREF M1 M4 RB Rn DELAY/ MRB CONTROL BLOCK RESET M6 Cd/MRB RC M2 VSS * Diodes inside the circuit are an ESD protection diode and a parasitic diode. (4)XC6132N Series E/F/H/K/M type (RESETB OUTPUT: Nch open drain/Active Low) HYS VSEN VIN M3 RSEN=RA+RB+RC M5 Rp + RA M1 - SURGE VOLTAGE PROTECT BLOCK VREF M4 RB Rn DELAY/ MRB CONTROL BLOCK RESETB M6 Cd/MRB RC M2 VSS * Diodes inside the circuit are an ESD protection diode and a parasitic diode. 3/30 XC6132 Series ■PRODUCT CLASSIFICATION ●Ordering Information XC6132①②③④⑤⑥-⑦(*1) DESIGNATOR ITEM ① Output Configuration ②③ Detect Voltage 08～20 e.g. 1.0V → ②=1, ③=0 ④ TYPE A～M Refer to Selection Guide ⑤⑥-⑦(*1) Packages (Order Unit) MR-G SOT-26 (3,000pcs/Reel) ER-G USP-6C (3,000pcs/Reel) (*1) SYMBOL DESCRIPTION C CMOS output N Nch open drain output The “-G” suffix denotes Halogen and Antimony free as well as being fully EU RoHS compliant. ●Selection Guide TYPE RESET/RESETB OUTPUT A Active High(*2) 1：0 144kΩ：0Ω 0.1%(TYP) B ↑ 1：0.125 144kΩ：18kΩ ↑ C ↑ 1：1 144kΩ：144kΩ ↑ D ↑ 2：1 288kΩ：144kΩ ↑ L ↑ 0.076：1 11kΩ：144kΩ ↑ E Low(*2) (*2) Active DELAY(Rp:Rn) HYSTERESIS 1：0 144kΩ：0Ω ↑ F ↑ 1：0.125 144kΩ：18kΩ ↑ H ↑ 1：1 144kΩ：144kΩ ↑ K ↑ 2：1 288kΩ：144kΩ ↑ M ↑ 0.076：1 11kΩ：144kΩ ↑ ”Active High” is H level when detection occurs, and “Active Low” is L level when detection occurs. 4/30 XC6132 Series ■PIN CONFIGURATION ●A/B/C/D/L type Cd/MRB 6 VSEN 4 VSS 5 1 HYS VSEN 6 VSS 5 2 1 VIN 2 RESET Cd/MRB 4 3 3 VIN RESET HYS SOT-26 (TOP VIEW) USP-6C (BOTTOM VIEW) ●E/F/H/K/M type Cd/MRB 6 VSS 5 VSEN 4 1 HYS VSEN 6 VSS 5 2 1 VIN 2 RESETB Cd/MRB 4 3 3 VIN RESETB HYS SOT-26 (TOP VIEW) USP-6C (BOTTOM VIEW) *The dissipation pad for the USP-6C package should be solder-plated in reference mount pattern and metal masking so as to enhance mounting strength and heat release. If the pad needs to be connected to other pins, it should be connected to VSS (No. 5) pin. ■PIN ASSIGNMENT PIN NUMBER PIN NAME FUNCTION VIN Power Input RESETB Reset Output (Active Low)(*1) RESET Reset Output (Active High)(*1) 1 HYS Adjustable Pin for Hysteresis Width 4 6 VSEN Voltage Sense 5 5 VSS Ground 6 4 Cd/MRB Adjustable Pin for Delay Time/ Manual Reset SOT-26 USP-6C 1 3 2 2 3 (*1) Refer to the ④ in Ordering Information table. 5/30 XC6132 Series ■FUNCTION CHART PIN NAME SIGNAL STATUS L Forced Reset H For details, refer to " Function Chart " OPEN Normal Operation Cd/MRB ●Function Chart 1.6V≦VIN≦6.0Ｖ Transition of VRESETB Condition Transition of VRESET Condition TYPE:A/B/C/D/L TYPE:E/F/H/K/M VCd/MRB≦VMRL Reset (High Level)(*2) Reset (Low Level)( *1) VCd/MRB≧VMRH Release (Low Level)(*1) Release (High Level)(*2) VCd/MRB≦VMRL Reset (High Level)( *2) Reset (Low Level)( *1) VCd/MRB≧VMRH Undefined(*3) Undefined(*3) VSEN VCd/MRB VSEN≧VDF+VHYS VSEN≦VDF (*1) CMOS output: VIN × 0.1 or less, N-ch open drain output, pull-up voltage × 0.1 or less. CMOS output: VIN × 0.9 or higher, N-ch open drain output, pull-up voltage × 0.9 or higher. (*3) For details,refer to page 17＜Manual reset function＞. Note: If used with VIN＜VSEN, the surge protection circuit will activate. Use with VIN≧VSEN. (*2) ■ABSOLUTE MAXIMUM RATINGS Ta=25℃ PARAMETER SYMBOL RATINGS Input Voltage VIN -0.3～+7.0 VSEN Pin Voltage VSEN -0.3～+VIN+0.3 or HYS Pin Voltage VHYS -0.3～+7.0 Cd/MRB Pin Voltage Output Voltage VCd/MRB XC6132C(*2) XC6132N(*3) VRESETB VRESET UNITS V +7.0(*1) V V -0.3～+VIN+0.3 or +7.0(*1) -0.3～+VIN+0.3 or +7.0(*1) V V -0.3～+7.0 V ±5.0 mA ±50 mA +50 mA IHYS +50 mA ISENSURGE(+) +2.5(*4) mA ISENSURGE(-) -2.5(*5) mA VSEN Pin Surge Voltage(+) VSENSURGE(+) +7.0(*4) V VSEN Pin Surge Voltage(-) VSENSURGE(-) -0.9 (*5) V Cd/MRB Pin Current Output Current XC6132C ICd/MRB (*2) XC6132N(*3) HYS Pin Current VSEN Pin Surge Current(+) VSEN Pin Surge Current(-) IRBOUT IROUT 250 SOT-26 Power Dissipation Pd USP-6C 600 (40mm x 40mm Standard board) (*6) 100 mW 1250 (JEDEC board) (*6) Operating Ambient Temperature Topr -40～+125 ℃ Storage Temperature Tstg -55～+125 ℃ * All voltages are described based on the VSS. (*1) The maximum value should be either V +0.3 or +7.0 in the lowest. IN (*2) CMOS Output (*3) N-ch Open Drain Output (*4) Transient≦200ms. (*5) Transient≦20ms. (*6) This is a reference data taken by using the test board. Please see the power dissipation page for the mounting condition. 6/30 XC6132 Series ■ELECTRICAL CHARACTERISTICS PARAMETER SYMBOL Operating Voltage VIN VSEN Input Voltage VSEN Detect Voltage Temperature Characteristics Hysteresis Width CONDITIONS VIN：Refer to V-1(*2) VSEN=VDF×0.9V, VIN：Refer to V-1(*2) VSEN=VDF×1.1V, VIN=6.0V Release Delay Resistance (TYPE:A/B/C/E/F/H) Release Delay Resistance Rp (TYPE:D/K) Release Delay Resistance (TYPE:L/M) Detect Delay Resistance (TYPE:C/D/H/K/L/M) Detect Delay (TYPE:B/F) Detect Delay Time(*6) 6.0 1.6 6.0 V 0 6.0 0 6.0 V - ±50 - - ±50 - - VDF VDF ×0.001 ×0.007 - VDF VDF ×0.001 ×0.01 - E-1(*3) - E-2(*3) 1.36 - E-3(*3) - 1.65 - E-5(*4) VIN=6.0V,VSEN=6.0V 2.80 - 1.36 - 1.65 E-6(*4) - ppm/℃ V 4.22 µA ② MΩ ③ kΩ ④ µs ⑤ E-4(*3) - 3.25 ① 4.97 - VIN=6.0V,VSEN=6.0V, VCd/MRB=0V 130 144 158 122 144 166 VIN=6.0V,VSEN=6.0V, VCd/MRB=0V 259 288 317 245 288 331 VIN=6.0V,VSEN=6.0V, VCd/MRB=0V 8.3 11 18.4 7.6 11 20.0 VIN=6.0V,VSEN=0V, VCd/MRB=6.0V 130 144 158 122 144 166 VIN=6.0V,VSEN=0V, VCd/MRB=6.0V 16.8 18 19.1 16.2 18 19.8 20 102 - 20 136 Rn Resistance Release Delay Time(*5) 1.6 V VHYS RSEN MAX. VDF(T) VDF(T) VDF(T) VDF(T) VDF(T) VDF(T) ×0.988 ×1.012 ×0.973 ×1.027 VSEN=VDF×1.1V, SENSE Resistance MIN. VDF(T)(*1)=1.5V～2.0V ∆VDF/ -40℃≦Topr≦125℃ (∆Topr・VDF) Iss2 TYP. UNITS CIRCUIT MAX. V VIN=6.0V Supply Current 2 TYP. VDF(T)(*1)=0.8V～1.4V VDF Iss1 MIN. VDF(T) VDF(T) VDF(T) VDF(T) VDF(T) VDF(T) -18mV +18mV -36mV +36mV VSEN=VDF×0.9V, Supply Current 1 -40℃≦Ta≦125℃(*7) Ta=25℃ tDR0 VIN=6.0V, VSEN=VDF×0.9V→VDF×1.1V - tDF0 VIN=6.0V, VSEN=VDF×1.1V→VDF×0.9V - 20 82 - 20 116 Unless otherwise specified in measurement conditions, Cd/MRB pin and HYS pin are open. (*1) VDF(T): Nominal detect voltage (*2) For VIN conditions, refer to SPEC TABLE (p.10). (*3) Refer to SPEC TABLE (p.10). (*4) Refer to SPEC TABLE (p.11). (*5) RESETB product: Time from when the VSEN pin voltage reaches the release voltage until the reset output pin reaches 5.4V (VIN×90%). RESET product: Time from when the VSEN pin voltage reaches the release voltage until the reset output pin reaches 0.6V(VIN×10%) Release voltage (VDR)=Detect voltage (VDF)+Hysteresis width (VHYS). (*6) RESETB product: Time from when the VSEN pin voltage reaches the detect voltage until the reset output pin reaches 0.6V(VIN×10%). RESET product: Time from when the VSEN pin voltage reaches the detect voltage until the reset output pin reaches 5.4V(VIN×90%). (*7) The ambient temperature range (-40℃≦Ta≦125℃) is a design Value. 7/30 XC6132 Series ■ELECTRICAL CHARACTERISTICS (Continued) PARAMETER SYMBOL Hysteresis Output Current IHYSOUT IHYSLEAK Hysteresis Output Leakage Current CONDITIONS -40℃≦Ta≦125℃(*12) Ta=25℃ MIN. TYP. MAX. MIN. TYP. MAX. VIN=1.6V, VSEN=0V,VHYS=0.3V 1.9 3.4 - 0.7 3.4 - VIN=6.0V,VSEN=6.0V, VHYS=6.0V - 0.01 0.1 - 0.01 1.0 VIN=1.6V(*9) 1.9 3.4 - 0.7 3.4 - VIN=2.0V 4.2 6.0 - 2.0 6.0 - VIN=3.0V 8.6 10.5 - 4.3 10.5 - VIN=4.0V 12.7 14.1 - 6.2 14.1 - VIN=5.0V 15.6 17.0 - 7.3 17.0 - VIN=6.0V 17.8 19.2 - 8.1 19.2 - VIN=1.6V(*10) - -1.2 -0.7 - -1.2 -0.48 VIN=3.0V - -3.0 -2.5 - -3.0 -1.1 VIN=6.0V - -4.9 -4.4 - -4.9 -2.5 VIN=1.6V(*10) 1.9 3.4 - 0.7 3.4 - VIN=2.0V(*11) 4.2 6.0 - 2.0 6.0 - VIN=3.0V 8.6 10.5 - 4.3 10.5 - VIN=4.0V 12.7 14.1 - 6.2 14.1 - VIN=5.0V 15.6 17.0 - 7.3 17.0 - VIN=6.0V 17.8 19.2 - 8.1 19.2 - VIN=1.6V(*9) - -1.2 -0.7 - -1.2 -0.48 VIN=3.0V - -3.0 -2.5 - -3.0 -1.1 VIN=6.0V - -4.9 -4.4 - -4.9 -2.5 VIN=6.0V,VSEN=6.0V, Nch. VRESETB=6.0V - 0.01 0.1 - 0.01 1.0 ILEAKP VIN=6.0V,VSEN=0V, Pch. VRESETB=0V - -0.01 - - -0.01 - ILEAKN(*8) VIN=6.0V,VSEN=0V, Nch. VRESET=6.0V - 0.01 0.1 - 0.01 1.0 VIN=6.0V,VSEN=6.0V, Pch. VRESET=0V - -0.01 - - -0.01 - UNITS CIRCUIT mA ⑥ µA VSEN=VDF×0.9V, Nch. VRESETB=0.3V IRBOUTN RESETB Output Current mA VSEN=VDF×1.1V, IRBOUTP Pch. VRESETB=VIN-0.3V VSEN=VDF×1.1V, Nch. VRESET=0.3V IROUTN RESET Output Current ⑦ mA VSEN=VDF×0.9V, Pch. VRESET=VIN-0.3V IROUTP RESETB Output Leakage Current RESET Output Leakage Current ILEAKN(*8) ILEAKP µA Unless otherwise specified in measurement conditions, Cd/MRB pin and HYS pin are open. (*8) Max. value is for XC6132N (Nch open drain). (*9) For 0.8V≦VDF(T)≦1.7V only. (*10) For 0.8V≦VDF(T)≦1.4V only. (*11) For 0.8V≦VDF(T)≦1.8V only. (*12) The ambient temperature range (-40℃≦Ta≦125℃) is a design Value. 8/30 XC6132 Series ■ELECTRICAL CHARACTERISTICS (Continued) PARAMETER SYMBOL Cd Pin Sink Current (TYPE:A/E) ICd Cd Pin Threshold Voltage(Release) VTCd1 VIN:Refer to V-1(*13), VSEN=0V→VDF×1.1V Cd Pin Threshold Voltage(Detect) VTCd2 VIN:Refer to V-1(*13), VSEN=VDF×1.1V→0V MRB High Level Voltage VMRH VMRL MRB Low Level Voltage tMRIN(*14) MRB Minimum Pulse Width tMRIN(*15) CONDITIONS VIN=1.6V, VCd/MRB=0.5V, VSEN=0V -40℃≦Ta≦125℃(*16) Ta=25℃ MIN. TYP. 0.92 1.2 MAX. MIN. TYP. 0.66 1.2 MAX. UNITS CIRCUIT mA ⑧ VIN×0.46 VIN×0.5 VIN×0.54 VIN×0.46 VIN×0.5 VIN×0.54 V ⑨ VIN:1.6V～6.0V, VSEN= VDF×1.1V, VIN>VSEN VIN×0.55 V VIN:1.6V～6.0V, VSEN= VDF×1.1V, VIN>VSEN 0 VIN:Refer to V-1(*13), VSEN=VDF×1.1V, Apply pulse from VDF×1.1V to 0V to the MRB pin. VIN VIN×0.55 VIN ⑩ 5.0 - VIN×0.18 0 - 5.0 VIN×0.18 - V - µs 32.0 - - 32.0 - ⑪ - Unless otherwise specified in measurement conditions, Cd/MRB pin and HYS pin are open. (*13) For VIN conditions, refer to SPEC TABLE (p.10). (*14) Specification is guaranteed for types A/B/C/D/L/E/F/H/K/M of the CMOS output product and types E/F/H/K/M of the Nch open drain product. (*15) Specification is guaranteed for types A/B/C/D/L of the Nch open drain output product. (*16) The ambient temperature range (-40℃≦Ta≦125℃) is a design Value. 9/30 XC6132 Series ■ELECTRICAL CHARACTERISTICS (SPEC TABLE) Table of Characteristics by Voltage Setting NOMINAL DETECT VOLTAGE(V) VDF(T) 10/30 V-1 INPUT VOLTAGE (V) 0.8 1.6 0.9 ↑ 1.0 ↑ 1.1 ↑ 1.2 ↑ 1.3 ↑ 1.4 ↑ 1.5 VDF×1.1 1.6 ↑ 1.7 ↑ 1.8 ↑ 1.9 ↑ 2.0 ↑ E-1 E-2 E-3 E-4 Ta=25℃ -40℃≦Ta≦125℃ Ta=25℃ -40℃≦Ta≦125℃ Supply Current 1(µA) Supply Current 2(µA) TYP. MAX. TYP. MAX. TYP. MAX. TYP. MAX. 1.28 2.65 1.28 3.92 1.32 2.75 1.32 4.26 1.30 2.70 1.30 4.02 1.43 2.91 1.43 4.49 XC6132 Series ■ELECTRICAL CHARACTERISTICS (SPEC TABLE) (Continued) Table of Characteristics by Voltage Setting NOMINAL DETECT E-5(Ta=25℃) E-6(-40℃≦Ta≦125℃) VOLTAGE(V) SENSE Resistance(MΩ) SENSE Resistance(MΩ) VDF(T) MIN. TYP. MIN. TYP. 0.8 7.5 20.7 5.9 20.7 0.9 8.6 23.3 6.8 23.3 1.0 10.0 26.1 7.6 26.1 1.1 11.0 28.6 8.5 28.6 1.2 12.2 31.3 9.3 31.3 1.3 13.4 33.9 10.2 33.9 1.4 14.5 36.6 11.1 36.6 1.5 15.7 38.6 11.9 38.6 1.6 16.9 39.2 12.8 39.2 1.7 18.1 39.8 13.6 39.8 1.8 19.3 40.4 14.5 40.4 1.9 19.0 40.2 14.3 40.2 2.0 18.6 39.9 14.0 39.9 11/30 XC6132 Series ■TEST CIRCUITS CIRCUIT① VIN VSEN RESET RESETB Cd/MRB V HYS V VSS CIRCUIT② A VIN VSEN RESET RESETB Cd/MRB HYS VSS CIRCUIT③ A VIN VSEN RESET RESETB Cd/MRB HYS VSS CIRCUIT④ VSEN A Cd/MRB HYS VIN RESET RESETB VSS *“RESET” is A/B/C/D/L type, and “RESETB” is E/F/H/K/M type. 12/30 XC6132 Series ■TEST CIRCUITS (Continued) CIRCUIT⑤ VIN VSEN RESET RESETB Cd/MRB Wave Form Measure Point HYS VSS CIRCUIT⑥ VIN VSEN RESET RESETB Cd/MRB A HYS VSS CIRCUIT⑦ VIN VSEN RESET RESETB Cd/MRB HYS A VSS CIRCUIT⑧ VSEN A Cd/MRB HYS VIN RESET RESETB VSS *“RESET” is A/B/C/D/L type, and “RESETB” is E/F/H/K/M type. 13/30 XC6132 Series ■TEST CIRCUITS (Continued) CIRCUIT⑨ VIN VSEN RESET RESETB Cd/MRB V HYS V V VSS CIRCUIT⑩ VSEN VIN RESET RESETB Cd/MRB V HYS V VSS CIRCUIT⑪ VSEN Cd/MRB HYS *“RESET” is A/B/C/D/L type, and “RESETB” is E/F/H/K/M type. 14/30 VIN RESET RESETB VSS Wave Form Measure Point V XC6132 Series ■OPERATIONAL DESCRIPTION Fig. 1 shows a typical block diagram. Fig. 2 shows the timing chart of Fig. 1. R2 VSEN HYS VIN M3 RSEN=RA+RB+RC M5 M7 +B Rp + R1 RA - SURGE VOLTAGE PROTECT BLOCK VREF M1 M4 RB Rn DELAY/ MRB CONTROL BLOCK VDD Cd/MRB RESET SW RC Cd RESETB M6 M2 VSS * The XC6132N series (N-ch open drain output) requires a resistor to pull up the output. Fig. 1: Typical block diagram (Active Low product) VSEN pin voltage:VSEN(MIN.:0V,MAX.:6.0V) Release voltage:VDF+VHYS Detect voltage:VDF Cd/MRB pin voltage:VCd/MRB(MIN.:VSS,MAX.:VIN) Cd pin threshold voltage:VTCd1,VTCd2 Output voltage:VRESETB(MIN.:VSS,MAX.:VIN) ｔDF ① ② ｔDR ③ ④⑤ ⑥ Fig. 2: Timing chart of Fig. 1(VIN=6.0V、Active Low product) ①In the initial state, a voltage that is sufficiently high (MAX.:6.0V) with respect to the release voltage is applied to the VSEN pin, and the delay capacitance Cd is charged up to the power input pin voltage. The VSEN pin voltage starts to fall, and during the time until it reaches the detect voltage (VSEN＞VDF), VRESETB is High level (=VIN). Note: If the pull-up resistor is connected to a power supply other than the power input pin VIN when using the Nch open drain output (XC6132N), High level will be the voltage of the power supply to which the pull-up resistor is connected. 15/30 XC6132 Series ■OPERATIONAL DESCRIPTION (Continued) ②The VSEN pin voltage continues to drop, and when it reaches the detect voltage (VSEN=VDF), the Nch transistor for delay capacitance discharge turns ON, and discharge of the delay capacitance Cd starts through the delay resistor Rn. The time from VSEN=VDF until VRESETB reaches Low level is the detect delay time tDF (the detect time when the capacitor is not connected to the Cd/MRB pin is tDF0). The delay capacitance Cd is discharged through the delay resistor Rn when it is above the threshold voltage of VTCD2. When it is below the threshold voltage of VTCD2, the delay capacitance Cd is discharged faster through the internal built-in low impedance switch. ③During the time that the VSEN pin voltage is below the detect voltage VDF, the delay capacitance Cd discharges to ground level. The VSEN pin starts rising again, and during the time until it reaches the release voltage (VSENVDF), VRESETB holds High level. The above operation description is for an Active Low detection product. For an Active High product, reverse the logic of the reset pin. In the factory shipping state, internal hysteresis is not added (VHYS =VDFx0.001V(TYP.)), so please add a hysteresis of 1% or more with an external resistor. For the calculation method, refer to below. Also please refer to “Notes on use 5＆6” on page 19. Hysteresis can be added as desired by inserting a resistor between the node to monitor and VSEN pin, and between the VSEN pin and HYS pin. The calculation method for adding hysteresis by increasing only the release voltage and leaving the detect voltage unchanged is given below. For the circuit schematic, refer to Fig. 3: Hysteresis Augmentation Circuit 1. VDR(H)=VDR(T)×{1+(RD/RE)} Hysteresis width=VDR(H)-VDF(T) Example 1: RD=200kΩ, RE=200kΩ, VDF(T)=1.000V, VDR(T)=1.001V. VDR(H)=2.002V Hysteresis width=2.002-1.000 =1.002V The calculation method for detecting high voltage and adding hysteresis is shown below. For the circuit schematic, refer to Fig. 4: Hysteresis Augmentation Circuit 2. VDF(H)=VDF(T)×{1+(R1/R2)} VDR(H)=VDR(T)×{1+(R1/R2)+(R1/R3)} Hysteresis width=VDR(H)-VDF(H) Example 2: R1=R3=500kΩ, R2=200kΩ, VDF(T)=2.000V, VDR(T)=2.002V. VDF(H)=7.0V VDR(H)=9.009V Hysteresis width=9.009-7.0=2.009V (Note 1) VDF(H) is the detect voltage after external adjustment. (Note 2) VDR(H) is the release voltage after external adjustment. (Note 3) VDR(T) is the release voltage. (Note 4) VDF(T) is the detect voltage. (Note 5) The R2 resistance is in parallel with the internal RSEN resistance, and thus to increase the accuracy of the detect voltage and release voltage after external adjustment, select an R2 resistance that is sufficiently small with respect to the RSEN resistance. For RSEN resistance values, refer to SPEC TABLE (p.11). (Note 6) If high voltage is to be detected, divide the voltage with resistors R1 and R2 so that VSEN pin≦6V. The battery voltage (+B) assumes up to 12V in this case. VDD +B VDD +B RE RD HYS R3 R1 VIN HYS Rpull(*1) RESET RESETB RESET SW Cd VSS RESET RESETB R2 Cd/MRB Fig. 3: Hysteresis Augmentation Circuit 1 16/30 Rpull(*1) VSEN VSEN GND VIN GND RESET SW Cd Cd/MRB VSS Fig. 4: Hysteresis Augmentation Circuit 2 XC6132 Series ■OPERATIONAL DESCRIPTION (Continued) The release delay time and detect delay time are determined by the delay resistors (Rp and Rn) and the delay capacitance Cd. The ratio of the delay resistances (Rp and Rn) is selectable from 5 options. The delay time is adjustable using the combination of delay resistance and delay capacitance value. (Refer to “Selection Guide”) The release delay time (tDR) is calculated using Equation (1). * ln is the natural logarithm. tDR=Rp×Cd×{-ln(1-VTCd1/VIN)}+tDR0 …(1) The delay capacitance pin threshold voltage is VTCd1=VIN/2(TYP.), and thus when tDR0 can be neglected, the release delay time can be calculated simply using Equation (2). tDR=Rp×Cd×[-ln{1-(VIN/2)/VIN}]=Rp×Cd×0.693 …(2) The detect delay time (tDF) is calculated using Equation (3). tDF=Rn×Cd×{-ln(VTCd2/VIN)}+tDF0 …(3) * ln is the natural logarithm. The delay capacitance pin threshold voltage is VTCd2=VIN/2 (TYP.), and thus when tDF0 can be neglected, the detect delay can be calculated simply using Equation (4). tDF=Rn×Cd×{-ln(VIN/2)/VIN}=Rn×Cd×0.693 …(4) Example 3: When type A is selected (Rp：Rn=144kΩ：0Ω),the delay times are as follows: If Cd is set to 0.1uF, tDR=144×103×0.1×10-6×0.693=10ms tDF is the detect delay time (tDFO) when the delay capacitance Cd is not connected. Example 4: When type B is selected (Rp：Rn=144kΩ：18kΩ),the delay times are as follows: If Cd is set to 0.1uF, tDR=144×103×0.1×10-6×0.693=10ms tDF =18×103×0.1×10-6×0.693=1.25ms (Note 7) The release delay times tDR in Examples 3 and 4 are the values calculated from Equation (2). (Note 8) The detect delay time tDF in Example 4 is the value calculated from Equation (4). (Note 9) Note that the delay times will vary depending on the actual capacitance value of the delay capacitance Cd. The Cd/MRB pin can also be used as a manual reset pin. When the Cd and RESET switch are connected to the Cd/MRB pin (refer to Fig.1), and under the release condition, if the RESET switch turns on, then the detect signal is generated at the RESET/RESETB pin forcibly. For Active Low type (RESETB), under the release condition, if the RESET switch turns on, then the voltage at the RESETB pin changes from H to L after the detect delay time. For Active High type (RESET), under the release condition, if the RESET switch turns on, then the voltage at the RESET pin changes from L to H after the detect delay time. Under the detect condition, the condition will be kept even if the RESET switch turns on and off. In the case that either H level or L level is fed to the Cd/MRB pin without the RESET switch, the behavior of the XC6132 follows the timing chart in Fig. 5. L level is fed to the MRB pin under the detect condition, the RESET switch will be kept. H level is fed to the MRB pin under the detect condition, the RESET switch will be undefined. Even though the voltage at the VSEN pin changes from a higher voltage than the detect voltage to a lower voltage, as long as H level is fed to the MRB pin, the release condition is kept. If H level or L level is fed to the Cd/MRB pin forcibly, then even though Cd is connected to the pin, the XC6132 can’t have any delay time. Release voltage:VDF+VHYS Detect voltage:VDF VSEN pin voltage:VSEN （MIN.:0V,MAX.:6.0V) MRB High level voltage:VMRH Cd pin threshold voltage:VTCd MRB Low level voltage:VMRL Cd/MRB pin voltage:VCd/MRB (MIN.:VSS ,MAX.:VIN) Release voltage:VDF+VHYS Detect voltage:VDF Undefined Output voltage:VRESE TB (MIN.:VSS ,MAX.:VIN(CMOS),Vpu ll(Nch open drain)) Fig. 5: Manual reset operation using the Cd/MRB pin (VIN =6.0V, Active Low product) 17/30 XC6132 Series ■OPERATIONAL DESCRIPTION (Continued) A surge voltage protection circuit is incorporated into the VSEN pin. A surge current of +2.5mA(≧200ms), -2.5mA(≧20ms) is possible. A positive surge current (ISENSURGE(+)) flows when M1 is turned ON by a SURGE VOLTAGE PROTECT BLOCK signal. A negative surge current (ISENSURGE(-)) is made to flow by the M1 parasitic diode. When a positive surge current flows and the surge voltage protection circuit activates, the VSEN pin voltage rises in proportion to the VIN voltage and surge current, so adjust the ISEN current with an external resistor so that the VSEN pin voltage does not exceed the operating voltage. Refer to Fig. 7. ※The VSEN voltage rise is most pronounced at high temperature. Example 5： When VIN=3.3V and ISENSURGE(+)=2.5mA (MAX), the VSEN pin voltage from Fig. 7 is 5.6V. If the maximum battery voltage (+B) pin voltage is 100V, a voltage of (100-5.6)=94.4V will be applied to the R1 resistor. To keep the surge current from exceeding 2.5mA, use a resistance of R1=V/I=94.4/0.0025=37.8kΩ or above. Example 6： When VIN = 3.3V and ISENSURGE(-) = -2.5mA(MAX), Vf of the parasitic diode M1 is -0.9V (MAX). If the battery voltage (+B) maximum is -100V, the voltage applied to the R1 resistor will be {-100 - (-0.9)} = -99.1V. To limit the surge current to -2.5mA, set the R1 resistance to R1 = V/I= -99.1/-0.0025 = 39.6kΩ or higher. If the surge voltage on the positive side is different from the negative side, calculate the R1 resistance value using the side where the voltage difference applied to the R1 resistor is greatest. +B Resistance for hysteresis external adjustment R1 R2 HYS R3 VSEN RSEN=RA+RB+RC RA + SURGE VOLTAGE PROTECT BLOCK RB M1 - VIN ↓ISENSURGE (+) VREF ↑ISENSURGE(-) RC M2 Surge voltage protect circuit Fig. 6: Surge voltage protect circuit Fig. 7: Example of VIN-VSEN characteristics 18/30 M3 XC6132 Series ■NOTES ON USE 1) Please use this IC within the stated maximum ratings. For temporary, transitional voltage drop or voltage rising phenomenon, the IC is liable to malfunction should the ratings be exceeded. 2) The power input pin voltage may fall due to the flow through current during IC operation and the resistance component between the power supply and the power input pin. In the case of CMOS output, a drop in the power input pin voltage may occur in the same way due to the output current. When this happens, if the power input pin voltage drops below the minimum operating voltage, a malfunction may occur. 3) Note that large, sharp changes of the power input pin voltage may lead to malfunction. 4) Power supply noise is sometimes a cause of malfunction. Sufficiently test using the actual device, such as inserting a capacitor between VIN and GND. 5) Internal hysteresis is not initially included with the product. Connect external resistors to the VSEN pin and HYS pin to add a hysteresis of 1% or more. Note that if hysteresis is not added with external resistors, oscillation will occur when switching takes place at the detect voltage or the release voltage. 6) There is a possibility that oscillation will occur if the resistances of the VSEN pin and HYS pin are high. Use a resistance of 1MΩ or less between the node to monitor and VSEN pin, and between the VSEN pin and HYS pin. 7) Exercise caution if VIN and VSEN are started in common, as the output will be undefined until VIN reaches the operating voltage. 8) For a manual reset function, in case when the function is activated by feeding either MRB H level or MRB L level to Cd/MRB pin instead of using a reset switch, please note these phenomena below; ・The RESET output signal will be undefined when MRB H is fed to Cd/MRB pin under the detect condition. ・The RESET output signal will be undefined based on the voltage relationship between VSEN pin and Cd/MRB pin. 9) When an N-ch open drain output is used, the VRESETB voltage at detection and release is determined by the pull-up resistance connected to the output pin. Refer to the following when selecting the resistance value. At detection: VRESETB=Vpull/(1+Rpull/RON) Vpull：Voltage after pull-up RON(*1)：ON resistance of N-ch driver M6 (calculated from VRESETB/IRBOUTN based on electrical characteristics) Example: When VIN=2.0V(*2), RON=0.3/4.2×10-3=71.4Ω (MAX.). If it is desired to make VRESETB at detection 0.1V or less when Vpull is 3.0V, Rpull={(Vpull/VRESETB)-1}×RON={(3/0.1)-1}×71.4≒2.1kΩ Therefore, to make the output voltage at detection 0.1V or less under the above conditions, the pull-up resistance must be 2.1kΩ or higher. (*1) Note that R ON becomes larger as VIN becomes smaller. (*2) For V in the calculation, use the lowest value of the input voltage range you will use. IN At release: VRESETB=Vpull/(1+Rpull/Roff) Vpull: Voltage after pull-up Roff: Resistance when N-ch driver M6 is OFF (calculated from VRESETB/ILEAKN based on electrical characteristics) Example: When Vpull is 6.0V, Roff=6/(0.1×10-6)=60MΩ (MIN.). If it is desired to make VRESETB 5.99V or higher, Rpull={(Vpull/VRESETB)-1}×Roff={(6/5.99)-1}×60×106≒100kΩ Therefore, to make the output voltage at release 5.99V or higher under the above conditions, the pull-up resistance must be 100kΩ or less. 10) If the discharge time of the delay capacitance Cd at detection is short and the delay capacitance Cd cannot be discharged to ground level, charging will take place at the next release operation with electric charge remaining in the delay capacitance Cd, and this may cause the release delay time to become noticeably short. 11) If the charging time of the delay capacitance Cd at release is short and the delay capacitance Cd cannot be charged to the VIN level, the delay capacitance Cd will discharge from less than the VIN level at the next detection operation, and this may cause the detect delay time to become noticeably short. 12) Torex places an importance on improving our products and their reliability. We request that users incorporate fail-safe designs and post-aging protection treatment when using Torex products in their systems. 19/30 XC6132 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (1) Detect, Release Voltage vs. Ambient Temperature (3) Supply Current vs. Ambient Temperature (4) Supply Current vs. Input Voltage 20/30 (2) Output Voltage vs Sense Voltage XC6132 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) (5) Sense Resistance vs Ambient Temperature (6) Delay Resistance vs Ambient Temperature 21/30 XC6132 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) (7) Delay Time vs Ambient Temperature (8) Hysteresis Output Current vs Ambient Temperature (9) Hysteresis Output Current vs Input Voltage (10) Hysteresis Output Leakage Current vs Ambient Temperature (11) RESET Output Current vs Ambient Temperature 22/30 XC6132 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) (11) RESET Output Current vs Ambient Temperature (Continued) (12) RESET Output Current vs Input Voltage (13) RESET Output Leakage Current vs Ambient Temperature (14) Cd Pin Sink Current vs Ambient Temperature (15) Cd Pin Sink Current vs Input Voltage 23/30 XC6132 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) (16) Cd Pin Threshold Voltage vs Ambient Temperature (17) MRB High Level Threshold Voltage vs Ambient Temperature 24/30 (18) MRB Low Level Threshold Voltage vs Ambient Temperature XC6132 Series ■PACKAGING INFORMATION ●SOT-26 (unit:mm) 2.9±0.2 +0.1 0.4 -0.05 +0.1 0.4 -0.05 6 5 4 2 0.2MIN 3 +0.1 0.15 -0.05 (0.95) 1.1±0.1 (0.95) 1.3MAX 1 1.6 1234 +0.2 -0.1 2.8±0.2 0～0.1 ●SOT-26 Reference Pattern Layout (unit:mm) 1.0 2.4 0.7 0.95 0.95 25/30 XC6132 Series ■PACKAGING INFORMATION (Continued) ●USP-6C (unit:mm) ●USP-6C Reference Pattern Layout (unit:mm) 26/30 ●USP-6C Reference Metal Mask Design XC6132 Series ■PACKAGING INFORMATION (Continued) ●SOT-26 Power Dissipation Toprmax+125℃ (40mm x 40mm Standard board) Power dissipation data for the SOT-26 is shown in this page. The value of power dissipation varies with the mount board conditions. Please use this data as the reference data taken in the following condition. 1. Measurement Condition Condition： Mount on a board Ambient： Natural convection Soldering： Lead (Pb) free Board： Dimensions 40 x 40 mm Copper (Cu) traces occupy 50% of the board 40.0 28.9 (1600 mm2 in one side) area In top and back faces Package heat-sink is tied to the copper traces Material： Glass Epoxy (FR-4) Thickness ： 1.6mm 2.5 Through-hole： 4 x 0.8 Diameter Evaluation Board (Unit：mm) 2.Power Dissipation vs. Ambient Temperature Board Mount (Tj max = 125℃ ) Ambient Temperature（℃） Power Dissipation Pd（ mW ） Thermal Resistance (℃/ W ) 25 85 125 600 240 0 166.67 Pd vs. Ta Power Dissipation Pd (mW) 700 600 500 400 300 200 100 0 25 45 65 85 105 125 Ambient Temperature Ta (℃) 27/30 XC6132 Series ■PACKAGING INFORMATION (Continued) ●USP-6C Power Dissipation (JEDEC board) Power dissipation data for the USP-6C is shown in this page. The value of power dissipation varies with the mount board conditions. Please use this data as one of reference data taken in the described condition. 76.2 1. Measurement Condition (Reference data) Condition : Mount on a board Ambient : Natural convection Soldering : Lead (Pb) free Board : The board using 4 copper layer. (76.2mm×114.3mm・・・ Area: about 8700mm2） 1st layer : No copper foil (Signal layer) 3rd layer : 70mm×70mm_Connected to heat-sink. 4th layer : No copper foil (Signal layer) Material : Glass Epoxy （ FR-4） 114.3 2nd layer : 70mm×70mm_Connected to heat-sink. Thickness : 1.6mm 8.74 Through-hole : φ0.2mm x 60pcs Evaluation Board (Unit：mm) 2.Power Dissipation vs. Ambient temperature Board Mount(Tjmax = 125℃) AmbientTemperature（℃） PowerDissipation Pd（mW) 25 85 125 1250 500 0 80.00 Pd-Ta 1400 Power DissipationPd（mW） θja(℃/W) 1200 1000 800 600 400 200 0 25 28/30 45 65 Ta（℃） 85 105 125 XC6132 Series ■MARKING RULE SOT-26 6 5 2 ③ ⑤ ② ④ ① ③ 1 ⑤ ② 4 ④ ① USP-6C 3 1 2 5 4 3 ① represents products series MARK X 6 PRODUCT SERIES XC6132******-G ②,③ represents internal sequential number 01, …,09, 10, …, 99, A0, …, A9, B0, …, B9, …, Z9… repeated. (G, I, J, O, Q, W excluded) ④,⑤ represents production lot number 01～09, 0A～0Z, 11～9Z, A1～A9, AA～AZ, B1～ZZ in order. (G, I, J, O, Q, W excluded) * No character inversion used. 29/30 XC6132 Series 1. The product and product specifications contained herein are subject to change without notice to improve performance characteristics. Consult us, or our representatives before use, to confirm that the information in this datasheet is up to date. 2. The information in this datasheet is intended to illustrate the operation and characteristics of our products. We neither make warranties or representations with respect to the accuracy or completeness of the information contained in this datasheet nor grant any license to any intellectual property rights of ours or any third party concerning with the information in this datasheet. 3. Applicable export control laws and regulations should be complied and the procedures required by such laws and regulations should also be followed, when the product or any information contained in this datasheet is exported. 4. The product is neither intended nor warranted for use in equipment of systems which require extremely high levels of quality and/or reliability and/or a malfunction or failure which may cause loss of human life, bodily injury, serious property damage including but not limited to devices or equipment used in 1) nuclear facilities, 2) aerospace industry, 3) medical facilities, 4) automobile industry and other transportation industry and 5) safety devices and safety equipment to control combustions and explosions. Do not use the product for the above use unless agreed by us in writing in advance. 5. Although we make continuous efforts to improve the quality and reliability of our products; nevertheless Semiconductors are likely to fail with a certain probability. So in order to prevent personal injury and/or property damage resulting from such failure, customers are required to incorporate adequate safety measures in their designs, such as system fail safes, redundancy and fire prevention features. 6. Our products are not designed to be Radiation-resistant. 7. Please use the product listed in this datasheet within the specified ranges. 8. We assume no responsibility for damage or loss due to abnormal use. 9. All rights reserved. No part of this datasheet may be copied or reproduced unless agreed by Torex Semiconductor Ltd in writing in advance. TOREX SEMICONDUCTOR LTD. 30/30