XC6220 Series
ETR0341-016
1A LDO Voltage Regulator with “Green Operation”
■GENERAL DESCRIPTION
☆Green Operation-Compatible
The XC6220 series is a highly accurate, low noise, high speed, low dropout, and large current CMOS voltage regulator with
Green Operation function. The series consists of a voltage reference, an error amplifier, a current limiter, an inrush current
prevention circuit and a phase compensation circuit plus a driver transistor.
With a 0.2Ω on-resistance driver transistor integrated, the ultra low dropout voltage performance with output currents up to 1A
greatly extends battery life as does the Green Operation function which can switch between high speed and power save modes
automatically. A low ESR ceramic capacitor can be used for the output stabilization capacitor (CL).
Output voltage is selectable in 0.05V increments within the range of 0.8V~5.0V, using laser trimming technologies.
An over current protection circuit and a thermal shutdown circuit are built in. The over current protection circuit will operate
when the output current reaches its limit current. The thermal shutdown circuit will operate when the junction temperature
reaches its limit temperature. The inrush prevention circuit works by controlling the inrush current which charges to CL when
the IC starts up. In this way, voltage fluctuations in power supply caused by inrush current during system start up can be
minimized.
The CE function enables the output to be turned off and the IC becomes a stand-by mode resulting in greatly reduced power
consumption.
■FEATURES
■APPLICATIONS
●Optical disk drive
Maximum Output Current
: 1000mA (1.2V≦VOUT≦5.0V)
Dropout Voltage
: 20mV @ 100mA (VOUT=3.0V)
●Magnetic disk drive
: 60mV@ 300mA (VOUT=3.0V)
●Digital still cameras / Camcorders
●Digital audio equipments
Operating Voltage Range
: 1.6V ~ 6.0V
Output Voltage Range
: 0.8V ~ 5.0V (0.05V increments)
Accuracy
: ± 1% (VOUT≧2.0V)
Low Power Consumption
: 8μA (TYP.) in PS mode
Thermal Shutdown
Inrush Current Prevention
CL Auto Discharge
CE Pull-Down Resistor
Output Capacitor
Packages
Environmentally Friendly
: 50μA (TYP.) in HS mode
: -40℃~ 85℃
: Detect 150℃, Release 135℃(TYP.)
: 700mA (MAX.)
: XC6220 Series B/D type
: XC6220 Series C/D type
: Ceramic Capacitor Compatible
: USP-6C, SOT-25, SOT-89-5
: EU RoHS Compliant, Pb Free
: ± 20mV (VOUT＜2.0V)
■TYPICAL APPLICATION CIRCUIT
■TYPICAL PERFORMANCE
CHARACTERISTICS
XC6220x 181
CE=VIN, CIN=CL =10μF (ceramic)
VIN
VIN
Input
CE
VOUT
CL=10μF
(ceramic)
CIN=10μF
(ceramic)
VSS
LOAD
Dropout Voltage: Vdif (mV)
500
Topr=25℃
Topr=-40℃
Topr=85℃
400
300
200
100
0
0
200
400
600
800
1000
Output Current: IOUT (mA)
1/26
XC6220 Series
■BLOCK DIAGRAMS
ON/OFF
Control
CE
V IN
-
CE
Error
Amp
CE/
ON/OFF
Control
CE
Current
Limit
+
CE
each
circuit
Error
Amp
CE/
Current
Limit
+
each
circuit
V OUT
Thermal
Protection
Green
Operation
V IN
-
V OUT
Green
Operation
R1
Thermal
Protection
R1
CE/
R2
R2
Voltage
Reference
Voltage
Reference
V SS
●XC6220 Series
Type A (Semi-custom)
XC6220Aｼﾘｰｽﾞ
ON/OFF
Control
CE
●XC6220
Series Type B
XC6220Bｼﾘｰｽﾞ
V IN
-
CE
RCE
Error
Amp
CE/
ON/OFF
Control
CE
CE
RCE
each
circuit
V OUT
Thermal
Protection
Green
Operation
V IN
-
Current
Limit
+
V SS
Error
Amp
CE/
Current
Limit
+
each
circuit
VOUT
Green
Operation
R1
Thermal
Protection
R1
CE/
R2
R2
Voltage
Reference
Voltage
Reference
V SS
●XC6220 XC6220Cｼﾘｰｽﾞ
Series Type C (Semi-custom)
V SS
XC6220Dｼﾘｰｽﾞ
●XC6220 Series
Type D (Semi-custom)
* Diodes inside the circuits are ESD protection diodes and parasitic diodes.
■PRODUCT CLASSIFICATION
●Ordering Information
XC6220 ①②③④⑤⑥-⑦(*1)
DESIGNATOR
ITEM
①
Type of CE
②③
Output Voltage
Output Voltage
( the 2nd decimal place)
④
Packages
(Order Unit)
⑤⑥-⑦
(*1)
SYMBOL
A
B
C
D
08 ~ 50
1
B
DESCRIPTION
without CE Pull-down resistor, without CL discharge (Semi-custom)
without CE Pull-down resistor, with CL discharge (Standard)
with CE Pull-down resistor, without CL discharge (Semi-custom)
with CE Pull-down resistor, with CL discharge (Semi-custom)
e.g. 3.0V → ②=3, ③=0
Output voltage {○.○0v} (the 2nd decimal place is “0”)
Output voltage {○.○5v} (the 2nd decimal place is “5”)
MR
SOT-25 (3,000pcs/Reel)
MR-G
SOT-25 (3,000pcs/Reel)
PR
SOT-89-5 (1,000pcs/Reel)
PR-G
SOT-89-5 (1,000pcs/Reel)
ER
USP-6C (3,000pcs/Reel)
ER-G
USP-6C (3,000pcs/Reel)
The “-G” suffix denotes Halogen and Antimony free as well as being fully EU RoHS compliant.
●Selection Guide
2/26
TYPE
CE PULL-DOWN RESISTOR
CL AUTO-DISCHARGE
A
B
C
No
No
Yes
No
Yes
No
D
Yes
Yes
XC6220
Series
■PIN CONFIGURATION
VIN
6
1
VOUT
VIN
5
2
VOUT
VSS
4
3
CE
VOUT
VOUT
NC
5
4
VIN
5
2
4
1
2
3
1
2
3
VIN
VSS
CE
CE
VSS
NC
USP-6C
SOT - 25
SOT-89-5
(BOTTOM VIEW)
( TOP VIEW)
(TOP VIEW)
* For the USP-6C, the No.5 and 6 VIN pins should be connected. The No.1 and 2 pins VOUT pins should be connected. The
dissipation pad should be solder-plated in reference mount pattern and metal masking so as to enhance mounting strength and
heat release. If the pad needs to be connected to other pins, it should be connected to the VSS (No. 4) pin.
■PIN ASSIGNMENT
SOT-25
PIN NUMBER
SOT-89-5
USP-6C
3
1
2
5
4
1
4
2
5
3
3
6, 5
4
1, 2
-
PIN NAME
FUNCTIONS
CE
VIN
VSS
VOUT
NC
ON/OFF Control
Power Input
Ground
Output
No connection
■FUNCTIONS
PIN NAME
DESIGNATOR
CONDITIONS
IC OPERATION
L
VCE≦0.4V
OFF
H
1.2V≦VCE≦6.0V
ON
VCE=OPEN(*1)
Undefined state
(XC6220A/B Series)
CE
OPEN
OFF (XC6220C/D Series)
(*1) Please avoid the state of OPEN, and connect CE pin to any arbitrary voltage.
* For the XC6220C/D series, CE function logic is fixed as L level because of the CE pull-down resister.
3/26
XC6220 Series
■ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
RATINGS
UNITS
Input Voltage
VIN
VSS - 0.3 ~ 6.5
V
Output Voltage
VOUT
VSS - 0.3 ~ VIN + 0.3
V
CE Input Voltage
VCE
VSS - 0.3 ~ 6.5
V
Pd
250
600 (40mm x 40mm Standard Board) (*1)
760 (JESD51-7 Board) (*1)
500
1300 (40mm x 40mm Standard Board) (*1)
1750 (JESD51-7 Board) (*1)
120
1000 (40mm x 40mm Standard Board) (*1)
1250 (JESD51-7 Board) (*1)
mW
Operating Ambient Temperature
Topr
-40 ~ 85
℃
Storage Temperature
Tstg
-55 ~ 125
℃
SOT-25
Power Dissipation
(Ta=25℃)
SOT-89-5
USP-6C
(*1)
The power dissipation figure shown is PCB mounted and is for reference only.
The mounting condition is please refer to PACKAGING INFORMATION.
4/26
XC6220
Series
■ELECTRICAL CHARACTERISTICS
●XC6220A/B/C/D Series
PARAMETER
Output Voltage
Output Current
SYMBOL
VOUT(E)
(*1)
IOUTMAX
CONDITIONS
MIN.
TYP.
MAX.
High Speed Mode (HS)
2.0V≦VOUT(T)≦5.0V
VCE=VIN, IOUT=30mA
×0.99
×1.01
High Speed Mode (HS)
0.8V≦VOUT(T)≦1.95V
VCE=VIN, IOUT=30mA
-0.02
+0.02
Power Save Mode (PS)
2.0V≦VOUT(T)≦5.0V
VCE=VIN, IOUT=0.1mA
×0.98
×1.02
Power Save Mode (PS)
0.8V≦VOUT(T)≦1.95V
VCE=VIN, IOUT=0.1mA
-0.04
+0.04
VCE=VIN
VIN=VOUT(T)+1.0V
0.8V≦VOUT(T)≦1.15V
VCE=VIN
VIN=VOUT(T)+1.0V
1.2V≦VOUT(T)≦5.0V
VOUT(T)(*2)
700
1200
1000
1200
-
10
45
ΔVOUT
High Speed Mode (HS),
VCE=VIN, 10mA≦IOUT≦300mA
-
Dropout Voltage1
Vdif (*3)
IOUT=300mA, VCE=VIN
-
Dropout Voltage2
Vdif (*3)
IOUT=1000mA, VCE=VIN
-
-
E-2
-
50
108
-
50
E-3
-
8
18
Supply Current 1
Supply Current 2
Stand-by Current
ISS1
ISS2
ISTBY
Line Regulation
ΔVOUT/
(ΔVIN・VOUT)
Input Voltage
VIN
Output Voltage
Temperature
Characteristics
ΔVOUT/
(ΔTa・VOUT)
VOUT(T)+0.5V≦VIN≦6.0V
1.1V≦VOUT(T)≦5.0V
VCE=VIN, IOUT=100mA
1.6V≦VIN≦6.0V
0.8V≦VOUT(T)≦1.05V
VCE=VInm, IOUT=100mA
VCE=VIN
IOUT=30mA
-40℃≦Ta≦85℃
Ta=25℃
CIRCUIT
V
①
mA
①
mV
①
mV
①
mV
①
μA
②
μA
②
-
Load Regulation
High Speed Mode(HS)
VIN=VCE=VOUT(T)+1.0V
IOUT=10mA (A/B Series)
High Speed Mode(HS)
VIN=VCE=VOUT(T)+1.0V
IOUT=10mA (C/D Series)
Power Save Mode(PS)
VIN=VCE=VOUT(T)+1.0V
IOUT=0.1mA (A/B Series)
Power Save Mode(PS)
VIN=VCE=VOUT(T)+1.0V
IOUT=0.1mA (C/D Series)
VIN=6.0V, VCE=VSS
UNITS
E-1
-
8
E-4
-0.1
0.01
0.1
μA
②
-
0.01
0.20
%/V
①
1.6
-
6.0
V
①
-
±100
-
ppm/℃
①
5/26
XC6220 Series
■ELECTRICAL CHARACTERISTICS (Continued)
PARAMETER
SYMBOL
CONDITIONS
Ta=25℃
MIN.
TYP.
MAX.
UNITS
CIRCUIT
-
50
-
dB
③
705
1200
-
1005
1200
-
mA
①
-
180
-
mA
①
1.0
2.0
-
mA
⑤
-
5.0
10
mA
⑤
IGOhys=IGO-IGOR
-
3.0
-
mA
⑤
VIN=VOUT(T)+1.0V, VCE= VIN
Time until HS mode is changed-over to
PS mode by IGOR.
-
-
E-5
μs
⑤
1.2
-
6.0
0.4
V
V
④
④
VIN=5.75VDC+0.5Vp-pAC
4.75V≦VOUT(T)≦5.0V
VCE=VIN, IOUT=30mA、f=1kHz
Ripple Rejection Ratio
PSRR
Limit Current
ILIM
Short Current
ISHORT
PS Switching Current
IGOR
HS Switching Current
IGO
Switch Current
Hysteresis Range
IGOhys
PS Switching Delay Time
tDPS
CE High Level Voltage
CE Low Level Voltage
VCEH
VCEL
CE High Level Current
ICEH
CE Low Level Current
CL Discharge Resistance
ICEL
(*4)
RDCHG
VIN=｛VOUT(T)+1.0｝VDC+0.5Vp-pAC
0.85V≦VOUT(T)≦4.7V
VCE=VIN, IOUT=30mA、f=1kHz
VIN=1.85VDC+0.5Vp-pAC
VOUT(T)=0.8V
VCE=VIN,IOUT=30mA、f=1kHz
VCE=VIN= VOUT(T)+1.0V
0.8V≦VOUT(T)≦1.15V
VCE=VIN= VOUT(T)+1.0V
1.2V≦VOUT(T)≦5.0V
VCE=VIN
Short VOUT to VSS level
：1.45V≦VOUT(T)≦5.0V
VIN=VOUT(T)+1.0V, VCE=VIN
：0.8V≦VOUT(T)≦1.4V
VIN=1.6V, VCE=VIN
IOUT=heavy to light load
：1.45V≦VOUT(T)≦5.0V
VIN=VOUT(T)+1.0V, VCE=VIN
：0.8V≦VOUT(T)≦1.4V
VIN=1.6V, VCE=VIN
IOUT=light to heavy load
VSS
VCE=VIN=6.0V(A/B series)
-0.1
-
0.1
μA
VCE=VIN=6.0V (C/D series)
-
9
15
μA
-0.1
-
0.1
μA
④
VIN=6.0V, VOUT=5.0V, VCE= VSS
-
460
-
Ω
①
VCE=VSS
④
Thermal Shutdown
Detect Temperature
TTSD
Junction Temperature
-
150
-
℃
①
Thermal Shutdown
Release Temperature
TTSR
Junction Temperature
-
135
-
℃
①
Inrush Current
IRUSH
VIN=VOUT(T)+1.0V、CL=22μF
VCE=0V→VOUT(T)+1.0V
(Only when rising and within 1ms)
-
-
700
mA
⑥
* 1: VOUT (E) = Effective output voltage
(The output voltage when an amply stabilized "VOUT (T) ＋1.0V" is provided at the VIN pin while maintaining a certain IOUT value.)
* 2: VOUT (T) = Nominal output voltage. (Shown in the voltage chart E-0)
* 3: Vdif = {VIN1-VOUT1}
VIN1 is the input voltage when VOUT1 appears at the VOUT pin while input voltage is gradually decreased.
VOUT1 is the voltage equal to 98% of the HS mode output voltage when an amply stabilized VOUT (T) +1.0V are supplied to the VIN pin.
* 4: For the XC6220B/D series only. The XC6220A/C series (semi-custom) discharges by only R1 and R2 resistors as shown in the block diagrams.
6/26
XC6220
Series
■ELECTRICAL CHARACTERISTICS (Continued)
●Voltage Chart 1
E-0
SYMBOL
NOMINAL
OUTPUT
VOLTAGE
(V)
VOUT(T)
E-1
E-2
E-3
E-4
SUPPLY
SUPPLY
E-5
PS
OUTPUT
OUTPUT
DROPOUT
DROPOUT
VOLTAGE 1
VOLTAGE 2
VOLTAGE 1
VOLTAGE 2
CURRENT 1
CURRENT 2
(HS Mode)
(PS Mode)
Vdif 1 (mV)
Vdif 2 (mV)
(XC6220C/D)
(XC6220C/D)
(V)
(V)
IOUT=300mA
IOUT=1000mA
(μA)
(μA)
VOUT
VOUT
Vdif1
Vdif2
ISS1
ISS2
tDPS
MAX.
MAX.
MAX.
MAX.
MIN.
MAX.
MIN.
MAX.
0.80
0.7800
0.8200
0.7600
0.8400
112.500
22.500
0.85
0.8300
0.8700
0.8100
0.8900
112.625
22.625
0.90
0.8800
0.9200
0.8600
0.9400
112.750
22.750
0.95
0.9300
0.9700
0.9100
0.9900
112.875
22.875
1.00
0.9800
1.0200
0.9600
1.0400
113.000
23.000
1.05
1.0300
1.0700
1.0100
1.0900
113.125
23.125
1.10
1.0800
1.1200
1.0600
1.1400
113.250
23.250
1.15
1.1300
1.1700
1.1100
1.1900
113.375
23.375
1.20
1.1800
1.2200
1.1600
1.2400
113.500
23.500
1.25
1.2300
1.2700
1.2100
1.2900
113.625
23.625
1.30
1.2800
1.3200
1.2600
1.3400
113.750
23.750
1.35
1.3300
1.3700
1.3100
1.3900
113.875
23.875
1.40
1.3800
1.4200
1.3600
1.4400
114.000
24.000
1.45
1.4300
1.4700
1.4200
1.4800
114.125
24.125
1.50
1.4800
1.5200
1.4700
1.5300
114.250
24.250
1.55
1.5300
1.5700
1.5100
1.5900
114.375
24.375
1.60
1.5800
1.6200
1.5600
1.6400
114.500
24.500
1.65
1.6300
1.6700
1.6100
1.6900
114.625
24.625
1.70
1.6800
1.7200
1.6600
1.7400
114.750
24.750
1.75
1.7300
1.7700
1.7100
1.7900
114.875
24.875
1.80
1.7800
1.8200
1.7600
1.8400
115.000
25.000
1.85
1.8300
1.8700
1.8100
1.8900
115.125
25.125
1.90
1.8800
1.9200
1.8600
1.9400
115.250
25.250
1.95
1.9300
1.9700
1.9100
1.9900
115.375
25.375
2.00
1.9800
2.0200
1.9600
2.0400
115.500
25.500
2.05
2.0295
2.0705
2.0090
2.0910
115.625
25.625
2.10
2.0790
2.1210
2.0580
2.1420
115.750
25.750
2.15
2.1285
2.1715
2.1070
2.1930
115.875
25.875
2.20
2.1780
2.2220
2.1560
2.2440
116.000
26.000
2.25
2.2275
2.2725
2.2050
2.2950
116.125
26.125
2.30
2.2770
2.3230
2.2540
2.3460
116.250
26.250
2.35
2.3265
2.3735
2.3030
2.3970
116.375
26.375
2.40
2.3760
2.4240
2.3520
2.4480
116.500
26.500
2.45
2.4255
2.4745
2.4010
2.4990
116.625
26.625
2.50
2.4750
2.5250
2.4500
2.5500
116.750
26.750
2.55
2.5245
2.5755
2.4990
2.6010
116.875
26.875
2.60
2.5740
2.6260
2.5480
2.6520
117.000
27.000
2.65
2.6235
2.6765
2.5970
2.7030
117.125
27.125
2.70
2.6730
2.7270
2.6460
2.7540
117.250
27.250
2.75
2.7225
2.7775
2.6950
2.8050
117.375
27.375
2.80
2.7720
2.8280
2.7440
2.8560
117.500
27.500
2.85
2.8215
2.8785
2.7930
2.9070
117.625
27.625
2.90
2.8710
2.9290
2.8420
2.9580
117.750
27.750
2.95
2.9205
2.9795
2.8910
3.0090
117.875
27.875
TYP.
400
MAX.
575
－
240
180
150
100
85
405
305
215
700
150
130
655
65
110
SWITCH
DELAY
TIME
(μs)
650
850
1200
7/26
XC6220 Series
■ELECTRICAL CHARACTERISTICS (Continued)
●Voltage Chart 2
E-0
E-1
E-2
E-3
E-4
OUTPUT
DROPOUT
DROPOUT
SUPPLY
SUPPLY
VOLTAGE
VOLTAGE
VOLTAGE 1
VOLTAGE 2
CURRENT 1
CURRENT 2
(HS Mode)
(PS Mode)
Vdif 1 (mV)
Vdif 2 (mV)
(XC6220C/D)
(XC6220C/D)
IOUT=300mA
IOUT=1000mA
(μA)
(μA)
SYMBOL
NOMINAL
OUTPUT
VOLTAGE
(V)
(V)
(V)
PS
SWITCH
DELAY
TIME
(μs)
Vdif2
ISS1
ISS2
tDPS
MAX.
MAX.
MAX.
MAX.
3.0600
118.000
28.000
3.1110
118.125
28.125
3.0380
3.1620
118.250
28.250
3.1815
3.0870
3.2130
118.375
28.375
3.1680
3.2320
3.1360
3.2640
118.500
28.500
3.2175
3.2825
3.1850
3.3150
118.625
28.625
3.30
3.2670
3.3330
3.2340
3.3660
118.750
28.750
3.35
3.3165
3.3835
3.2830
3.4170
118.875
28.875
3.40
3.3660
3.4340
3.3320
3.4680
119.000
29.000
3.45
3.4155
3.4845
3.3810
3.5190
119.125
29.125
3.50
3.4650
3.5350
3.4300
3.5700
119.250
29.250
3.55
3.5145
3.5855
3.4790
3.6210
119.375
29.375
3.60
3.5640
3.6360
3.5280
3.6720
119.500
29.500
3.65
3.6135
3.6865
3.5770
3.7230
119.625
29.625
3.70
3.6630
3.7370
3.6260
3.7740
119.750
29.750
3.75
3.7125
3.7875
3.6750
3.8250
119.875
29.875
3.80
3.7620
3.8380
3.7240
3.8760
120.000
30.000
3.85
3.8115
3.8885
3.7730
3.9270
120.125
30.125
3.90
3.8610
3.9390
3.8220
3.9780
120.250
30.250
3.95
3.9105
3.9895
3.8710
4.0290
120.375
30.375
4.00
3.9600
4.0400
3.9200
4.0800
120.500
30.500
4.05
4.0095
4.0905
3.9690
4.1310
120.625
30.625
4.10
4.0590
4.1410
4.0180
4.1820
120.750
30.750
4.15
4.1085
4.1915
4.0670
4.2330
120.875
30.875
4.20
4.1580
4.2420
4.1160
4.2840
121.000
31.000
4.25
4.2075
4.2925
4.1650
4.3350
121.125
31.125
4.30
4.2570
4.3430
4.2140
4.3860
121.250
31.250
4.35
4.3065
4.3935
4.2630
4.4370
121.375
31.375
4.40
4.3560
4.4440
4.3120
4.4880
121.500
31.500
4.45
4.4055
4.4945
4.3610
4.5390
121.625
31.625
4.50
4.4550
4.5450
4.4100
4.5900
121.750
31.750
4.55
4.5045
4.5955
4.4590
4.6410
121.875
31.875
VOUT(T)
8/26
OUTPUT
E-5
VOUT
VOUT
Vdif1
MIN.
MAX.
MIN.
MAX.
3.00
2.9700
3.0300
2.9400
3.05
3.0195
3.0805
2.9890
3.10
3.0690
3.1310
3.15
3.1185
3.20
3.25
TYP.
60
MAX.
95
655
53
85
4.60
4.5540
4.6460
4.5080
4.6920
122.000
32.000
4.65
4.6035
4.6965
4.5570
4.7430
122.125
32.125
4.70
4.6530
4.7470
4.6060
4.7940
122.250
32.250
4.75
4.7025
4.7975
4.6550
4.8450
122.375
32.375
4.80
4.7520
4.8480
4.7040
4.8960
122.500
32.500
4.85
4.8015
4.8985
4.7530
4.9470
122.625
32.625
4.90
4.8510
4.9490
4.8020
4.9980
122.750
32.750
4.95
4.9005
4.9995
4.8510
5.0490
122.875
32.875
5.00
4.9500
5.0500
4.9000
5.1000
123.000
33.000
1200
1450
XC6220
Series
■TEST CIRCUITS
Circuit 1
・測定回路1 (出力電圧・出力電流・入出力電圧差・入力動作電圧・入力安定度・負荷安定度・制限電流・
短絡電流・CL放電抵抗)
VIN
A
VOUT
CIN
(ceramic)
V
Circuit 2
CL
CE
(ceramic)
V
VSS
SW1
SW2
IOUT
RL
・測定回路2(消費電流・ｽﾀﾝﾊﾞ ｲ電流)
A
VIN
CIN
(ceramic)
CE
SW1
A
VOUT
CL
(ceramic)
VSS
SW2
PS:0.1mA
HS:10mA
A
Circuit 3 ・測定回路3(リップル除去率)
IOUT= 30mA
VIN
A
VOUT
CL
(ceramic)
V
CE
VSS
V
RL
9/26
XC6220 Series
■TEST CIRCUITS (Continued)
Circuit 4
・測定回路4 (CE” H” L” レベル 電圧・ CE” H” L” レベル 電流)
VIN
A
CIN
VOUT
CE
VSS
(ceramic)
V
V
VCE
Circuit 5
CL
(ceramic)
・測定回路5 (HS切替電流、PS切替電流、切替ﾋｽﾃﾘｼｽ電流、PS切替遅延時間)
IOUT
A
VOUT
VIN
CE
CIN
(ceramic)
V
VSS
RL
CL
(ceramic)
A
Circuit 6
・測定回路6
ISS
(突入電流防止)
A
VIN
VOUT
CE
V
CL = 22 uF
VSS
VCE
10/26
XC6220
Series
■OPERATIONAL EXPLANATION
ON/OFF
Control
CE
V IN
-
CE
RCE
Error
Amp
CE/
+
Current
Limit
each
circuit
VOUT
Green
Operation
Thermal
Protection
R1
CE/
R2
Voltage
Reference
V SS
The voltage divided by resistors R1 & R2 is compared
with the internal reference voltage by the error amplifier.
The P-channel MOSFET which is connected to the VOUT
pin is then driven by the subsequent control signal. The
output voltage at the VOUT pin is controlled & stabilized
by a system of negative feedback. The current limit
circuit and short protect circuit operate in relation to the
level of output current. The GO function monitors the
output current and switches the IC between two
operating modes according to the level of output current.
Further, the IC's internal circuitry can be shutdown via
the CE pin's signal.
XC6220x 301
CE=VIN, Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
50
Supply Current: ISS (μA)
The XC6220 series always operates in a green operation (GO) mode.
The GO mode enables the IC to switch automatically between the high
speed (HS) mode or the power save (PS) mode according to the level of
output current. The switching point of the HS mode and the PS mode is
fixed inside the IC. When the output current becomes IGOR=1.0mA (MIN.)
or below, the mode changes automatically to the PS mode after a delay
time of hundreds of microseconds. Supply current in light load is greatly
reduced. Also when the output current becomes IGO 10mA (MAX.) or
more, the mode changes automatically to the HS mode and the IC returns
to high speed operation.
40
30
20
10
0
0
5
10
15
20
Output Current: IOUT (mA)
The XC6220 series has a built-in phase compensation circuit which means that a stable output voltage is achieved even if
the IC is used with low ESR capacitors. In order to ensure stable phase compensation it is recommended that a CL capacitor
is connected as close as possible to the VOUT pin and VSS pin. For a stable power supply, please connect an input capacitor
(CIN) between the VIN pin and the VSS pin.
Values required for the phase compensation are shown in the chart below. If a loss of the capacitance happens, the stable
phase compensation may not be obtained. Please ensure to use a capacitor which does not depend on bias or temperature
too much.
Recommended output capacitor (CL)
OUTPUT CAPACITOR VALUE(CL)
VOUT(T)(V)
CIN=4.7μF
CIN=10μF
CIN=22μF
0.80V ~ 0.95V
1.00V ~ 1.45V
1.50V ~ 1.75V
1.80V ~ 2.95V
3.00V ~ 3.50V
3.55V ~ 5.00V
×
47μF
47μF
47μF
47μF
47μF
×
47μF
22μF
6.8μF
4.7μF
10μF
22μF
22μF
10μF
6.8μF
4.7μF
6.8μF
× No option
The XC6220 series includes a fold-back circuit, which aids the operation of the current limiter and circuit protection. When
the load current reaches the current limit level, the fold-back circuit operates and output voltage drops. As a result of this drop
in output voltage, output current also decreases. When the output pin is shorted, a current of about 180mA flows.
The IC's internal circuitry can be shutdown via the signal from the CE pin with the XC6220 series. With the XC6220A/C
series, output at the VOUT pin will be pulled down to the VSS level. However, with XC6220B/D series, the CL auto-discharge
N-channel transistor switch is connected in parallel to R1 and R2 while the power supply is applied to the VIN pin. Therefore,
the time until the VOUT pin reaches the VSS level is shortened.
The output voltage of the XC6220A/B series becomes unstable, when the CE pin is open. If this IC is used with the correct
output voltage for the CE pin, the logic is fixed and the IC will operate normally. On the other hand, with the XC6220C/D series,
the IC operation is stopped when the CE pin is open. However, the CE pin input current may increase as a result of through
current in the pull-down resistor (RCE) when the IC is under operation.
11/26
XC6220 Series
■OPERATIONAL EXPLANATION (Continued)
The XC6220B/D series can quickly discharge the electric charge at the output capacitor (CL) via the N-channel transistor
located between the VOUT pin and the VSS pin, when a low signal is inputted to the CE pin, which enables the whole IC circuit
put into an OFF state (cf. BLOCK DIAGRAM).
(VOUT pin voltage) ÷ (N-channel transistor through current) = CL discharge resistance (RDCHG)
The CL auto-discharge resistance value is fixed to 460Ω(VIN=6.0V, VOUT=5.0V at TYP.). The discharge time of the output
capacitor (CL) is set by the CL auto-discharge resistance (RDCHG) and the output capacitor (CL). By setting a time constant of
the CL auto-discharge resistance value [RDCHG] and an output capacitor value (CL) as τ(τ=C x RDCHG), the output voltage
after discharge via the N-channel transistor is calculated by the following formulas.
V = VOUT(E) x e –t/τ, or ｔ=τln( VOUT(E) / V )
where
V : Output voltage after discharge
VOUT(E) : Output voltage
t: Discharge time
τ: CL auto-discharge resistance RDCHG×Output capacitor (CL) value C)
The XC6220 series includes an inrush current Prevention circuit.
The inrush current protection circuit suppresses inrush current charged to CL when the IC starts up to 700 mA (MAX.) for
approximately 1ms.
* Please note that the device can not provide the output current beyond 700 mA for a period of approximately 1ms after the
CE pin goes high.
■NOTES ON USE
1. For temporary, transitional voltage drop or voltage rising phenomenon, the IC is liable to malfunction should the ratings be
exceeded.
2. Where wiring impedance is high, operations may become unstable due to noise and/or phase lag depending on output
current. Please strengthen VIN and VSS wiring in particular.
3. Please wire the input capacitor (CIN) and the output capacitor (CL) as close to the IC as possible.
4. As for the XC6220A/C series (semi-custom), the output voltage may float with a leakage current of the driver transistor
between VIN and VOUT and R1+R2 resistance while stand-by (operation stop). Please take consideration of this and check it
before use.
5. Torex places an importance on improving our products and their reliability. We request that users incorporate fail-safe
designs and post-aging protection treatment when using Torex products in their systems.
12/26
XC6220
Series
■TYPICAL PERFORMANCE CHARACTERISTICS
(1) Output Voltage vs. Output Current
XC6220x 121
XC6220x 121
VIN=CE=2.2V, CIN=CL =22μF (ceramic)
1.4
1.2
1.2
Output Voltage: VOUT (V)
Output Voltage: VOUT (V)
CE=VIN, Topr=25℃, CIN=CL =22μF (ceramic)
1.4
1
0.8
0.6
0.4
VIN=1.6V
VIN=2.2V
0.2
1
0.8
0.6
0.4
Topr=25℃
Topr=-40℃
Topr=85℃
0.2
0
0
0
0.2
0.4
0.6
0.8
1
1.2
0
1.4
0.2
0.4
XC6220x 301
1
1.2
1.4
VIN=CE=4.0V, CIN=10μF, CL =4.7μF (ceramic)
3.5
3
3
Output Voltage: VOUT (V)
Output Voltage: VOUT (V)
0.8
XC6220x 301
CE=VIN, Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
3.5
2.5
2
1.5
1
VIN=3.1V
VIN=4.0V
0.5
2.5
2
1.5
1
Topr=25℃
Topr=-40℃
Topr=85℃
0.5
0
0
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0
0.2
Output Current: IOUT (A)
0.4
0.6
1
1.2
1.4
XC6220x 501
CE=VIN, Topr=25℃, CIN=CL =10μF (ceramic)
6
0.8
Output Current: IOUT (A)
XC6220x 501
VIN=CE=6.0V, CIN=CL =10μF (ceramic)
6
5
5
Output Voltage: VOUT （V)
Output Voltage: VOUT (V)
0.6
Output Current: IOUT (A)
Output Current: IOUT (A)
4
3
2
VIN=5.1V
VIN=6.0V
1
4
3
2
Topr=25℃
Topr=-40℃
Topr=85℃
1
0
0
0
0.2
0.4
0.6
0.8
1
Output Current: IOUT (A)
1.2
1.4
0
0.2
0.4
0.6
0.8
1
1.2
1.4
Output Current: IOUT (A)
13/26
XC6220 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(2) Output Voltage vs. Input Voltage
XC6220x 121
XC6220x 301
CE=VIN, Topr=25℃, CIN=CL =22μF (ceramic)
1.4
1.2
3
Output Voltage: VOUT (V)
Output Voltage: VOUT (V)
CE=VIN, Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
3.5
1
0.8
0.6
0.4
IOUT=0.1mA
IOUT=30mA
IOUT=100mA
0.2
2.5
2
1.5
1
IOUT=0.1mA
IOUT=30mA
IOUT=100mA
0.5
0
0
0
1
2
3
4
5
6
0
1
2
Input Voltage: VIN (V)
3
4
5
6
Input Voltage: VIN (V)
XC6220x 501
CE=VIN, Topr=25℃, CIN=CL =10μF (ceramic)
6
Output Voltage: VOUT (V)
5
4
3
2
IOUT=0.1mA
IOUT=30mA
IOUT=100mA
1
0
0
1
2
3
4
5
6
Input Voltage: VIN (V)
(3) Dropout Voltage vs. Output Current
XC6220x 121
XC6220x 301
CE=VIN, Topr=25℃, CIN=CL =22μF (ceramic)
CE=VIN, Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
600
Topr=25℃
Topr=-40℃
Topr=85℃
500
400
Dropout Voltage: Vdif (mV)
Dropout Voltage: Vdif (mV)
600
300
200
100
0
400
300
200
100
0
0
200
400
600
Output Current: IOUT (mA)
14/26
Topr=25℃
Topr=-40℃
Topr=85℃
500
800
1000
0
200
400
600
800
Output Current: IOUT (mA)
1000
XC6220
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(3) Dropout Voltage vs. Output Current
X C6 2 2 0 x5 0 1
CE=VIN, Topr=25℃, CIN=CL =10μF (ceramic)
600
Dropout Voltage: Vdif (mV)
500
Topr=25℃
Topr=-40℃
Topr=85℃
400
300
200
100
0
0
200
400
600
800
1000
Output Current: IOUT (mA)
(4) Output Voltage vs. Ambient Temperature
XC6220x 121
VIN=CE=4.0V, IOUT=30mA,
CIN=10μF, CL =4.7μF (ceramic)
3.06
1.212
Output Voltage: VOUT (V)
Output Voltage: VOUT (V)
1.224
1.2
1.188
1.176
-50
XC6220x 301
VIN=CE=2.2V, IOUT=30mA,
CIN=CL =22μF (ceramic)
-25
0
25
50
75
100
Ambient Temperature: Tpor (℃)
3.03
3
2.97
2.94
-50
-25
0
25
50
75
100
Ambient Temperature: Tpor (℃)
XC6220x 501
VIN=CE=6.0V, IOUT=30mA,
CIN=CL =10μF (ceramic)
Output Voltage: VOUT (V)
5.1
5.05
5
4.95
4.9
-50
-25
0
25
50
75
100
Ambient Temperature: Tpor (℃)
15/26
XC6220 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(5) Supply Current vs. Input Voltage
XC6220x 121
XC6220B 121
90
CE=VIN, IOUT=10mA
CIN=CL =22μF (ceramic)
CIN=CL =22μF (ceramic)
Topr=25℃
Topr=-40℃
Topr=85℃
70
90
80
Supply Current: ISS （μA）
80
Supply Current: ISS (μA)
CE=VIN, IOUT=0.1mA
60
50
40
30
20
10
70
60
50
40
30
20
Topr=25℃
Topr=-40℃
Topr=85℃
10
0
0
0
1
2
3
4
5
6
0
1
2
Input Voltage: VIN (V)
Topr=25℃
Topr=-40℃
Topr=85℃
Topr=25℃
Topr=-40℃
Topr=85℃
80
Supply Current: ISS (μA)
Supply Current: ISS (μA)
70
6
CE=VIN, IOUT=10mA
CIN=10μF, CL =4.7μF (ceramic)
90
80
5
XC6220x 301
CE=VIN, IOUT=0.1mA
CIN=10μF, CL =4.7μF (ceramic)
90
60
50
40
30
20
10
70
60
50
40
30
20
10
0
0
0
1
2
3
4
5
6
0
1
2
Input Voltage: VIN (V)
90
5
6
CE=VIN, IOUT=10mA
CIN=CL =10μF (ceramic)
90
80
Supply Current: ISS (μA)
Topr=25℃
Topr=-40℃
Topr=85℃
70
4
XC6220x 501
CE=VIN, IOUT=0.1mA
CIN=CL =10μF (ceramic)
80
3
Input Voltage: VIN (V)
XC6220x 501
Supply Current: ISS (μA)
4
Input Voltage: VIN （V)
XC6220x 301
60
50
40
30
20
10
Topr=25℃
Topr=-40℃
Topr=85℃
70
60
50
40
30
20
10
0
0
0
1
2
3
4
Input Voltage: VIN (V)
16/26
3
5
6
0
1
2
3
4
Input Voltage: VIN (V)
5
6
XC6220
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(6) PS Switching Delay Time vs. Ambient Temperature
XC6220x 301
XC6220x 121
VIN=CE=2.2V, IOUT=10mA→0.1mA
CIN=CL =22μF (ceramic)
1600
1400
1400
1200
1200
1000
1000
TDPS (μs)
TDPS (μs)
1600
800
600
800
600
400
400
200
200
0
-50
-25
0
25
50
75
VIN=CE=4.0V, IOUT=10mA→0.1mA
CIN=10μF, CL =4.7μF (ceramic)
0
-50
100
-25
0
25
50
75
100
Ambient Temperature: Tpor (℃)
Ambient Temperature: Tpor (℃)
XC6220x 501
VIN=CE=6.0V, IOUT=10mA→0.1mA
CIN=CL =10μF (ceramic)
1600
1400
TDPS (μs)
1200
1000
800
600
400
200
0
-50
-25
0
25
50
75
100
Ambient Temperature: Tpor (℃)
(8) PS/HS Switch Current vs. Ambient Temperature
(7) CL Discharge Resistance vs. Ambient Temperature
XC6220B /D
XC6220x 301
VIN=6.0V, CE=VSS, VOUT=5.0V
CIN=10μF, CL =4.7μF (ceramic)
700
VIN=CE=4.0V, CIN=10μF, CL =4.7μF (ceramic)
10
9
Input Current: IOUT (mA)
Rdischg (Ω)
600
500
400
300
HS Switching Current
8
PS Switching Current
7
6
5
4
3
2
1
200
-50
-25
0
25
50
75
Ambient Temperature: Tpor (℃)
100
0
-50
-25
0
25
50
75
100
Ambient Temperature: Tpor (℃)
17/26
XC6220 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(9) Load Transient Response
XC6220x 121
XC6220x 121
VIN=CE=2.2V, Tr=Tf=5μs
VIN=CE=2.2V, Tr=Tf=5μs
Topr=25℃, CIN=CL =22μF (ceramic)
CH1
Topr=25℃, CIN=CL =22μF (ceramic)
CH1
Output Voltage
Output Voltage
300mA
300mA
Output Current
Output Current
CH2
0.1mA
CH2
10mA
200μs/div
CH1：100mV/div CH2：100mA/div
200μs/div
CH1：100mV/div CH2：100mA/div
XC6220x 301
XC6220x 301
VIN=CE=4.0V, Tr=Tf=5μs
Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
CH1
VIN=CE=4.0V, Tr=Tf=5μs
Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
CH1
Output Voltage
Output Voltage
300mA
300mA
Output Current
Output Current
CH2
0.1mA
CH2
10mA
200μs/div
CH1：100mV/div CH2：100mA/div
200μs/div
CH1：100mV/div CH2：100mA/div
XC6220x 501
XC6220x 501
VIN=CE=6.0V, Tr=Tf=5μs
Topr=25℃, CIN=10μF (ceramic)
VIN=CE=6.0V, Tr=Tf=5μs
Topr=25℃, CIN=CL =10μF (ceramic)
CH1
CH1
Output Voltage
Output Voltage
300mA
300mA
Output Current
CH2 0.1mA
CH2
200μs/div
CH1：100mV/div CH2：100mA/div
18/26
Output Current
10mA
200μs/div
CH1：100mV/div CH2：100mA/div
XC6220
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(10) Line Transient Response
XC6220x 301
XC6220x 121
CE=VIN, Tr=Tf=5μs, IOUT=100mA
Topr=25℃, CIN=CL =22μF (ceramic)
CE=VIN, Tr=Tf=5μs, IOUT=100mA
Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
3.2V
CH1
5.0V
Input Voltage
2.2V
CH1
Input Voltage
4.0V
CH2
CH2
Output Voltage
Output Voltage
100μs/div
CH1：1V/div CH2：20mV/div
100μs/div
CH1：1V/div CH2：20mV/div
XC6220x 501
CE=VIN, Tr=Tf=5μs, IOUT=100mA
Topr=25℃, CIN=CL =22μF (ceramic)
6.0V
CH1
Input Voltage
5.5V
CH2
Output Voltage
100μs/div
CH1：500mV/div CH2：20mV/div
(11) Input Rise Characteristics
XC6220x 121
XC6220x 121
CE=VIN, Tr=5μs, IOUT=0.1mA
Topr=25℃, CL =22μF (ceramic)
CE=VIN, Tr=5μs, IOUT=300mA
Topr=25℃, CL =22μF (ceramic)
2.2V
2.2V
Input Voltage
CH1
0V
Input Voltage
CH1
Output Voltage
CH2
0V
Output Voltage
CH2
200μs/div
CH1：1V/div CH2：500mV/div
200μs/div
CH1：1V/div CH2：500mV/div
19/26
XC6220 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(11) Input Rise Characteristics
XC6220x 301
XC6220x 301
CE=VIN, Tr=5μs, IOUT=0.1mA
CE=VIN, Tr=5μs, IOUT=300mA
Topr=25℃, CL =4.7μF (ceramic)
Topr=25℃, CL =4.7μF (ceramic)
4.0V
4.0V
Input Voltage
CH1
Input Voltage
0V
CH1
0V
Output Voltage
Output Voltage
CH2
CH2
200μs/div
CH1：2V/div CH2：2V/div
200μs/div
CH1：2V/div CH2：2V/div
XC6220x 501
XC6220x 501
CE=VIN, Tr=5μs, IOUT=0.1mA
Topr=25℃, CL =22μF (ceramic)
CE=VIN, Tr=5μs, IOUT=300mA
Topr=25℃, CL =22μF (ceramic)
6.0V
6.0V
Input Voltage
CH1
0V
Input Voltage
CH1
Output Voltage
CH2
0V
Output Voltage
CH2
200μs/div
CH1：2V/div CH2：2V/div
200μs/div
CH1：2V/div CH2：2V/div
(12) CE Rise Characteristics
XC6220x 121
XC6220x 121
VIN=2.2V, Tr=5μs, IOUT=300mA
Topr=25℃, CIN=CL =22μF (ceramic)
VIN=2.2V, Tr=5μs, IOUT=0.1mA
Topr=25℃, CIN=CL =22μF (ceramic)
CE Voltage
CE Voltage
CH1
CH1
Output Voltage
Output Voltage
CH2
CH2
100μs/div
CH1：500mV/div CH2：500mV/div
20/26
100μs/div
CH1：500mV/div CH2：500mV/div
XC6220
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(12) CE Rise Characteristics
XC6220x 301
XC6220x 301
VIN=4.0V, Tr=5μs, IOUT=0.1mA
Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
VIN=4.0V, Tr=5μs, IOUT=300mA
Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
CE Voltage
CE Voltage
CH1
CH1
Output Voltage
Output Voltage
CH2
CH2
100μs/div
CH1：500mV/div CH2：1V/div
100μs/div
CH1：500mV/div CH2：1V/div
XC6220x 501
XC6220x 501
VIN=6.0V, Tr=5μs, IOUT=300mA
Topr=25℃, CIN=CL =10μF (ceramic)
VIN=6.0V, Tr=5μs, IOUT=0.1mA
Topr=25℃, CIN=CL =10μF (ceramic)
CE Voltage
CE Voltage
CH1
CH1
Output Voltage
Output Voltage
CH2
CH2
100μs/div
CH1：500mV/div CH2：2V/div
100μs/div
CH1：500mV/div CH2：2V/div
(13) Inrush Current
XC6220x 301
XC6220x 121
VIN=4.0V, Tr=5μs
Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
VIN=2.2V, Tr=5μs
Topr=25℃, CIN=CL =22μF (ceramic)
CE Voltage
CE Voltage
Output Voltage
Output Voltage
CH1
CH2
CH1
CH2
Inrush Current
Inrush Current
CH3
CH3
100μs/div
CH1：500mV/div CH2：1V/div CH3：100mA/div
100μs/div
CH1：500mV/div CH2：1V/div CH3：100mA/div
21/26
XC6220 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(13) Inrush Current
XC6220x 501
VIN=6.0V, Tr=5μs
Topr=25℃, CIN=CL =10μF (ceramic)
CE Voltage
Output Voltage
CH1
CH2
Inrush Current
CH3
100μs/div
CH1：500mV/div CH2：1V/div CH3：100mA/div
(14) CL Discharge Time
XC6220x 301 ( A /C)
XC6220x 301 ( B /D )
VIN=4.0V, Tf=5μs, IOUT=0.1mA
VIN=4.0V, Tf=5μs, IOUT=0.1mA
Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
Topr=25℃, CIN=10μF, CL =4.7μF (ceramic)
CH1
CH1
CE Voltage
CE Voltage
CH2
CH2
Output Voltage
Output Voltage
2.0ms/div
CH1：500mV/div CH2：2V/div
200ms/div
CH1：500mV/div CH2：2V/div
(15) Ripple Rejection Ratio
X C6 2 2 0 x1 2 1 (P o we r S ave mo de )
XC6220x 121 ( H i g hSpeed mode)
VIN=CE=2.2VDC+0.5Vp-pAC, IOUT=30mA
Topr=25℃, CIN=0.1μF, CL =22μF (ceramic)
70
60
50
40
30
20
10
0
0.01
0.1
1
10
Ripple Frequency: f (kHz)
22/26
80
Ripple Rejection Ratio: RR (dB)
Ripple Rejection Ratio: RR (dB)
80
100
1000
VIN=CE=2.2VDC+0.5Vp-pAC, IOUT=0.1mA
Topr=25℃, CIN=0.1μF, CL =22μF (ceramic)
70
60
50
40
30
20
10
0
0.01
0.1
1
10
Ripp;e Frequency: f (kHz)
100
1000
XC6220
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(15) Ripple Rejection Ratio
XC6220x 301 ( Pow erSa v e mode)
XC6220x 301 ( H i g hSpeed mode)
VIN=CE=4.0VDC+0.5Vp-pAC, IOUT=30mA
Topr=25℃, CIN=0.1μF, CL =4.7μF (ceramic)
70
80
Ripple Rejection Ratio: RR (dB)
Ripple Rejection Ratio: RR (dB)
80
60
50
40
30
20
10
0
0.01
0.1
1
10
100
VIN=CE=4.0VDC+0.5Vp-pAC, IOUT=0.1mA
Topr=25℃, CIN=0.1μF, CL =4.7μF (ceramic)
70
60
50
40
30
20
10
0
0.01
1000
0.1
Ripple Frequency: f (kHz)
XC6220x501
XC6220c501(HighSpeed
( H i g hSpeedmode)
mode)
60
50
40
30
20
10
0.1
1
10
Ripple Frequency: f (kHz)
100
1000
100
1000
VIN=CE=5.5.0VDC+0.5Vp-pAC, IOUT=0.1mA
Topr=25℃, CIN=0.1μF, CL =10μF (ceramic)
80
Ripple Rejection Ratio: RR (dB)
Ripple Rejection Ratio: RR (dB)
70
0
0.01
10
XC6220x 501 ( Pow erSa v e mode)
VIN=CE=5.5.0VDC+0.5Vp-pAC, IOUT=30mA
Topr=25℃, CIN=0.1μF, CL =10μF (ceramic)
80
1
Ripple Frequency: f (kHz)
70
60
50
40
30
20
10
0
0.01
0.1
1
10
100
1000
Ripple Frequency: f (kHz)
23/26
XC6220 Series
■PACKAGING INFORMATION
For the latest package information go to, www.torexsemi.com/technical-support/packages
PACKAGE
OUTLINE / LAND
PATTERN
SOT-25
SOT-25 PKG
SOT-89-5
SOT-89-5 PKG
USP-6C
24/26
USP-6C PKG
THERMAL CHARACTERISTICS
Standard Board
JESD51-7 Board
Standard Board
JESD51-7 Board
Standard Board
JESD51-7 Board
SOT-25 Power Dissipation
SOT-89-5 Power Dissipation
USP-6C Power Dissipation
XC6220
Series
■MARKING RULE
SOT89-5
SOT25
5
4
2
4
1
③
⑤
②
④
6
5
4
3
①
2
⑤
③
④
②
1
③
⑤
②
④
2
①
①
5
USP6C
3
1
① represents product series
MARK
PRODUCT SERIES
H
XC6220******
2
3
② represents type of CE, voltage range, and accuracy
MARK
CE
OUTPUT VOLTAGE
RANGE
OUTPUT VOLTAGE
ACCURACY
PRODUCT SERIES
0
A
0.8～2.9
1
XC6220A081** ～ XC6220A291**
1
A
0.85～2.95
B
XC6220A08B** ～ XC6220A29B**
2
A
3.0～5.0
1
XC6220A301** ～ XC6220A501**
3
A
3.05～4.95
B
XC6220A30B** ～ XC6220A49B**
4
B
0.8～2.9
1
XC6220B081** ～ XC6220B291**
5
B
0.85～2.95
B
XC6220B08B** ～ XC6220B29B**
6
B
3.0～5.0
1
XC6220B301** ～ XC6220B501**
7
B
3.05～4.95
B
XC6220B30B** ～ XC6220B49B**
8
C
0.8～2.9
1
XC6220C081** ～ XC6220C291**
9
C
0.85～2.95
B
XC6220C08B** ～ XC6220C29B**
A
C
3.0～5.0
1
XC6220C301** ～ XC6220C501**
B
C
3.05～4.95
B
XC6220C30B** ～ XC6220C49B**
C
D
0.8～2.9
1
XC6220D081** ～ XC6220D291**
D
D
0.85～2.95
B
XC6220D08B** ～ XC6220D29B**
E
D
3.0～5.0
1
XC6220D301** ～ XC6220D501**
F
D
3.05～4.95
B
XC6220D30B** ～ XC6220D49B**
③ represents output voltage
OUTPUT
MARK
VOLTAGE (V)
0
1
2
3
4
5
6
7
8
9
－
－
－
－
－
－
－
－
0.8x
0.9x
3.0x
3.1x
3.2x
3.3x
3.4x
3.5x
3.6x
3.7x
3.8x
3.9x
MARK
A
B
C
D
E
F
H
K
L
M
OUTPUT
VOLTAGE (V)
1.0x
1.1x
1.2x
1.3x
1.4x
1.5x
1.6x
1.7x
1.8x
1.9x
4.0x
4.1x
4.2x
4.3x
4.4x
4.5x
4.6x
4.7x
4.8x
4.9x
MARK
N
P
R
S
T
U
V
X
Y
Z
OUTPUT
VOLTAGE (V)
2.0x
2.1x
2.2x
2.3x
2.4x
2.5x
2.6x
2.7x
2.8x
2.9x
④,⑤ represents production lot number
01～09、0A～0Z、11･･･9Z、A1～A9、AA･･･Z9、ZA～ZZ repeated
(G，I，J，O，Q，W excluded)
*No character inversion used.
5.0x
－
－
－
－
－
－
－
－
－
25/26
XC6220 Series
1.
The product and product specifications contained herein are subject to change without notice to
improve performance characteristics. Consult us, or our representatives before use, to confirm that
the information in this datasheet is up to date.
2.
The information in this datasheet is intended to illustrate the operation and characteristics of our
products. We neither make warranties or representations with respect to the accuracy or
completeness of the information contained in this datasheet nor grant any license to any intellectual
property rights of ours or any third party concerning with the information in this datasheet.
3.
Applicable export control laws and regulations should be complied and the procedures required by
such laws and regulations should also be followed, when the product or any information contained in
this datasheet is exported.
4.
The product is neither intended nor warranted for use in equipment of systems which require
extremely high levels of quality and/or reliability and/or a malfunction or failure which may cause loss
of human life, bodily injury, serious property damage including but not limited to devices or equipment
used in 1) nuclear facilities, 2) aerospace industry, 3) medical facilities, 4) automobile industry and
other transportation industry and 5) safety devices and safety equipment to control combustions and
explosions. Do not use the product for the above use unless agreed by us in writing in advance.
5.
Although we make continuous efforts to improve the quality and reliability of our products;
nevertheless Semiconductors are likely to fail with a certain probability. So in order to prevent personal
injury and/or property damage resulting from such failure, customers are required to incorporate
adequate safety measures in their designs, such as system fail safes, redundancy and fire prevention
features.
6.
Our products are not designed to be Radiation-resistant.
7.
Please use the product listed in this datasheet within the specified ranges.
8.
We assume no responsibility for damage or loss due to abnormal use.
9.
All rights reserved. No part of this datasheet may be copied or reproduced unless agreed by Torex
Semiconductor Ltd in writing in advance.
TOREX SEMICONDUCTOR LTD.
26/26
工商网监
湘ICP备2023018690号
