XC6401EEB0MR

XC6401 Series ETR0309_005 Dual LDO Regulators, Low ESR Cap. Compatible ■GENERAL DESCRIPTION The XC6401 series are highly accurate, Dual, low noise, CMOS LDO voltage regulators. Performance features of the series includes low output noise, high ripple rejection ratio, low dropout and very fast turn-on times. The XC6401 includes a reference voltage source, error amplifiers, driver transistors, current limiters and phase compensators internally. The XC6401’s current limiters' foldback circuit also operates as a short protect for the output current limiter. The output voltage for each regulator is set independently by laser trimming. Voltages are selectable in 50mV steps within a range of 0.8V to 5.0V. The XC6401 series is also fully compatible with low ESR ceramic capacitors, reducing cost and improving output stability. This high level of output stability is maintained even during frequent load fluctuations, due to the excellent transient response performance and high PSRR achieved across a broad range of frequencies. The EN function allows the output of each regulator to be turned off independently, resulting in greatly reduced power consumption. The XC6401 series is available in the SOT-26W or USP-6B, USP-6C ‘chip-scale’ package. ■APPLICATIONS ■FEATURES ●Mobile Phones ●Cordless phones and radio communication equipment ●Portable games ●Cameras, Video recorders ●Portable Audio Equipment ●PDAs Maximum Output Current : More than 150mA (300mA limit) Dropout Voltage : 100mV @100mA Operating Voltage Range : 1.5V ~ 6.0V Output Voltage Range : 0.8V~5.0V (50mV increments) Highly Accurate : ±2% (VOUT>1.5V) : ±30mV (VOUT≦1.5V) Low Power Consumption : 25μA (TYP.) Standby Current : Less than 0.1μA (TYP.) High Ripple Rejection : 70dB @1kHz Operating Temperature Range : -40℃ ~ +85℃ Low ESR Capacitor Compatible : Ceramic capacitor Low Output Noise Ultra Small Packages : SOT-26W,USP-6B,USP-6C ■TYPICAL APPLICATION CIRCUITS ■TYPICAL PERFORMANCE CHARACTERISTICS ●SOT-26W VOUT1 2 VIN VSS 5 3 EN2 VOUT2 4 6 1 ●Interactive Load Transient Response EN1 CL1 1uF CIN 1uF CL2 1uF ●USP-6 CIN 1uF 1 EN2 VOUT2 6 2 VIN VOUT1 5 3 EN1 VSS 4 CL1 1uF CL2 1uF 1/24 XC6401 Series ■PIN CONFIGURATION VOUT1 VSS 6 6 1 EN1 VOUT2 5 4 3 2 VIN EN2 SOT-26W (TOP VIEW) USP-6B / 6C (BOTTOM VIEW) *The dissipation pad for the USP-6B/C packages should be solder-plated in recommended mount pattern and metal masking so as to enhance mounting strength and heat release. If the pad needs to be connected to other pins, it should be connected to the VSS pin. ■PIN ASSIGNMENT PIN NUMBER SOT-26W USP-6B/C 1 3 2 2 3 1 4 6 5 4 6 5 PIN NAME FUNCTION EN1 VIN EN2 VOUT2 VSS VOUT1 ON/OFF Control 1 Power Input ON/OFF Control 2 Output 2 Ground Output 1 ■PRODUCT CLASSIFICATION ●Selection Guide The following options for the Regulator 1, 2, the EN pin logic, internal pull-up / down are available. ●Ordering Information XC6401①②③④⑤⑥ DESIGNATOR DESCRIPTION ① Regulator1, EN type ② Regulator2, EN type ③④ Output Voltage ⑤ Packaging Types SYMBOL E F G H E F G H 01~ M ⑥ 2/24 Device Orientation DESCRIPTION : High Active with pull-down resistor : High Active with no pull-down resistor : Low Active with pull-up resistor : Low Active with no pull-up resistor : High Active with pull-down resistor : High Active with no pull-down resistor : Low Active with pull-up resistor : Low Active with no pull-up resistor : Internally set sequential number relating output voltage of each regulators Regulator 1 Output Voltage Range: 0.8 ~ 5.0 V (50mV increments) Regulator 2 Output Voltage Range: 0.8 ~ 5.0 V (50mV increments) : SOT-26W D : USP-6B E : USP-6C R L : Embossed tape, standard feed : Embossed tape, reverse feed XC6401 Series ■ABSOLUTE MAXIMUM RATINGS PARAMETER Input Voltage Output Current Output Voltage EN Pin Voltage SOT-26W Power Dissipation USP-6B USP-6C Operating Temperature Range Storage Temperature Range Ta = 25℃ SYMBOL RATINGS UNITS VIN IOUT1 + IOUT2 VOUT VEN 6.5 700 VSS -0.3 ~ VIN +0.3 VSS -0.3 ~ 6.5 250 100 100 -40 ~ +85 -55 ~ +125 V mA V V Pd Topr Tstg mW ℃ ℃ * Sum of IOUT1 and IOUT2. ** Pd=(VIN-VOUT1)xIOUT1+(VIN-VOUT2)xIOUT2 ■ELECTRICAL CHARACTERISTICS XC6401FFxx Regulator 1, Regulator 2 Ta=25℃ PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNITS CIRCUIT Output Voltage (*3) VOUT (E) VIN=VOUT (T) + 1.0V IOUT=30mA 0.98 VOUT(T) 1.02 V 1 Maximum Output Current IOUTMAX VIN=VOUT (T) + 1.0V 150 - - mA 1 Load Regulation △VOUT 1mA≦IOUT≦100mA - 15 60 mV 1 Vdif1 IOUT=30mA E-1 mV Vdif2 IOUT=100mA VIN=VEN=VOUT (T) + 1.0V, IOUT=0mA E-2 mV Dropout Voltage Supply Current ISS Standby Current ISTB VIN=VOUT (T) + 1.0V, VEN=VSS △VOUT VOUT(T)+1.0V≦VIN≦6.0V Line Regulation (*7) △VIN ・ VOUT Input Voltage VIN Output Voltage △VOUT Temperature Characteristics △Topr ･ VOUT VEN=VIN, IOUT=30mA IOUT=30mA 1 - 25 45 μA 2 - 0.01 0.10 μA 3 - 0.01 0.20 %/V 1 1.5 - 6.0 V - - ±100 - ppm/℃ 1 - 70 - dB 5 - 300 - mA 1 - 30 - mA 1 Ripple Rejection Rate(*8) PSRR Current Limiter Ilim -40℃≦Topr≦85℃ VIN=[VOUT(T)+1.0]VDC+0.5Vp-pAC IOUT=30mA, f=1kHz VIN=VOUT (T) + 1.0V, VEN=VIN Short-Circuit Current Ishort VIN=VOUT (T) + 1.0V, VEN=VIN EN "High" Voltage VENH 1.30 - 6.0 V 4 EN "Low" Voltage VENL - - 0.25 V 4 EN "High" Current IENH VIN=VEN=VOUT (T) + 1.0V -0.10 - 0.10 μA 4 EN "Low" Current IENL VIN= VOUT (T) + 1.0V, VEN=VSS -0.10 - 0.10 μA 4 NOTE *1: VOUT(T)=Specified output voltage *2: VOUT(E)=Effective output voltage (I.e. the output voltage when "VOUT(T)＋1.0V" is provided at the VIN pin while maintaining a certain IOUT value). *3: If VOUT (T)≦1.45V, MIN VOUT (T) - 30mV, MAX VOUT (T) + 30mV (*6) (*5) *4: Vdif={VIN1 -VOUT1 } *5: VOUT1=A voltage equal to 98% of the output voltage whenever an amply stabilized IOUT {VOUT(T)+1.0V} is input. *6: VIN1=the input voltage when VOUT1 appears as input voltage is gradually decreased. *7: When VOUT(T)>4.5V, 5.5V