XC6601B12BMR

XC6601 Series Low Voltage Input LDO Voltage Regulators ■GENERAL DESCRIPTION ETR0335_003 The XC6601 series is a low voltage input CMOS LDO regulator which provides highly accurate (±20mV) outputs and can supply current efficiently due to its ultra low on-resistance even at low output voltages. The series is ideally suited to the applications which require very low dropout voltage operation and consists of a voltage reference, an error amplifier, a driver transistor, a current limiter, a fold back circuit, a thermal shutdown (TSD) circuit, an under voltage lock out (UVLO) circuit and a phase compensation circuit. Output voltage is selectable in 0.05V increments within a range of 0.7V to 1.8V using laser trimming technology and ceramic capacitors can be used for the output stabilization capacitor (CL). The over current protection circuit (the current limiter and the fold back circuit) as well as the thermal shutdown circuit (the TSD circuit) are built-in. These two protection circuits will operate when either the output current reaches the current limit level or the junction temperature reaches the temperature limit level. With the built-in UVLO function, the regulator output is forced OFF when the voltage level at the VBIAS pin or the VIN pin falls below the UVLO voltage level. The CE function enables the output to be turned off and the series to be put in stand-by mode resulting in greatly reduced power consumption. At the time of entering the stand-by mode, the series enables the electric charge at the output capacitor (CL) to be discharged via the internal auto-discharge switch which is located between the VOUT pin and the VSS pin. As a result the VOUT pin quickly returns to the VSS level. ■APPLICATIONS ●Mobile phones ●Cordless phones ●Wireless communication equipment ●Portable games ●Cameras ●Audio visual equipment ●Portable AV equipment ●PDAs ■FEATURES Bias Voltage Range Maximum Output Current Dropout Voltage : 400mA (Limiter 550mA TYP.) : 38mV@IOUT=100mA (TYP.) (at VBIAS - VOUT=2.4V) : 2.5V ~ 6.0V (VBIAS - VOUT≧1.2V) Input Voltage Range Output Voltage Range Output Voltage Accuracy Power Consumption UVLO TSD (Detect/Release) Operating Temperature Range CL High Speed Auto-Discharge Low ESR Capacitor Packages : 1.0V ~ 3.0V (VIN≦VBIAS) : 0.7V ~ 1.8V (0.05V increments) :±20mV : IBIAS=25μA , IIN=1.0μA (TYP.) : IBIAS=0.01μA , IIN=0.01μA (TYP.) : VBIAS=2.0V, VIN=0.4V (TYP.) :150℃/125℃ (TYP.) : -40℃ ~ 85℃ : Ceramic Capacitor Compatible : USP-6C, SOT-25, SOT-89-5 ■ TYPICAL APPLICATION CIRCUIT ■ TYPICAL PEFORMANCE CHARACTERISTICS ●VBIAS =3.6V , VIN =1.8V , VOUT =1.5V ●Dropout Voltage vs. Output Current XC 6 6 0 1 B 1 2 1 M R Ta=25 [℃] 300 250 Dropout Voltage: Vdif(mV) 200 150 100 50 0 0 100 200 　Output Current: IOUT(mA) 300 400 VBIAS=3.0V VBIAS=3.3V VBIAS=3.6V VBIAS=4.2V VBIAS=5.0V 1/32 XC6601 Series ■PIN CONFIGURATION ●USP-6C ●SOT-25 VOUT 5 CE 4 ●SOT-89-5 1 VIN *The heat dissipation pad of the USP-6C 2 VBIAS SOT-25 (TOP VIEW) 3 VSS package is recommended to solder as the recommended mount pattern and metal mask pattern for mounting strength. This pad should be electrically opened or connected to the VBIAS (No.1) pin. ■PIN ASSIGNMENT PIN NUMBER USP-6C 1 3 4 2 6 SOT-25 2 1 5 3 4 SOT-89-5 2 4 5 3 1 PIN NAME VBIAS VIN VOUT VSS CE FUNCTION Power Supply Input Driver Transistor Input Output Ground ON/OFF Control ■PRODUCT CLASSIFICATION ●Ordering Information XC6601①②③④⑤⑥ MARK ① ②③ DESCRIPTION Type of Regulators Output Voltage Output Voltage Accuracy SYMBOL A B 07 ~ 18 1 B M ⑤ Packages E P R L DESCRIPTION : CE High Active, Pull-Down Resistor Built-in, CL Auto Discharge Function : CE High Active, No Pull-Down Resistor Built-in, CL Auto Discharge Function : e.g.) VOUT(T)=1.2V⇒②=1,③=2 : 100mV increments, ±20mV accuracy e.g.) 1.2V⇒②=1,③=2,④=1 : 50mV increments, ±20mV accuracy e.g.) 1.25V⇒②=1,③=2,④=B : SOT-25 : USP-6C : SOT-89-5 : Embossed Tape (Standard Feed) : Embossed Tape (Reverse Feed) ④ ⑥ Device Orientation 2/32 XC6601 Series ■BLOCK DIAGRAMS (1) XC6601A Series (2) XC6601B Series *Diodes inside the circuit are an ESD protection diode and a parasitic diode. 3/32 XC6601 Series ■MAXIMUM ABSOLUTE RATINGS Ta=25 ℃ PARAMETER Bias Voltage Input Voltage Output Current Output Voltage CE Input Voltage USP-6C Power Dissipation SOT-25 SOT-89-5 Pd SYMBOL VBIAS VIN IOUT VOUT VCE RATINGS VSS-0.3 ~ +7.0 VSS-0.3 ~ +7.0 700 (*1) VSS-0.3 ~ VBIAS+0.3 VSS-0.3 ~ VIN+0.3 VSS-0.3 ~ +7.0 100 1000 (PCB mounted) *2 250 600 (PCB mounted) *2 500 1300 (PCB mounted) *2 -40 ~ +85 -55 ~ +125 UNITS V V mA V V mW Operating Temperature Range Topr ℃ Storage Temperature Range Tstg ℃ (*1) IOUT=Less than Pd / (VIN-VOUT) (*2) The power dissipation figure shown is PCB mounted. Please refer to pages 28~30 for details. 4/32 XC6601 Series ■ELECTRICAL CHARACTERISTICS PARAMETER Bias Voltage Input Voltage (*1) (*2) Ta=25 ℃ MIN. 2.5 1.0 -0.02 TYP. VOUT(T) E-0 (*4) (*5) SYMBOL VBIAS VIN VOUT(E) (*3) IOUTMAX 1 IOUTMAX 2 IOUTMAX 3 △VOUT Vdif1(*7) Vdif2 (*7) Vdif3 (*7) Vdif4 (*7) IBIAS IIN CONDITIONS VCE =VBIAS,VIN =VOUT(T)+0.3V VBIAS=VCE=3.6V VBIAS=VCE=3.6V, VIN =VOUT(T)+0.3V, IOUT=100mA VCE =VBIAS ,VBIAS -VOUT(T)≧1.2V VIN =VOUT(T)+0.5V VCE =VBIAS ,VBIAS -VOUT(T)≧1.3V VIN =VOUT(T)+0.5V VCE =VBIAS ,VBIAS -VOUT(T)≧1.5V VIN =VOUT(T)+0.5V VBIAS=VCE=3.6V, VIN=VOUT(T)+0.3V, 1mA≦IOUT≦300mA VBIAS=VCE, IOUT=100mA VCE =VBIAS , IOUT=200mA VCE =VBIAS , IOUT=300mA VCE =VBIAS , IOUT=400mA VBIAS=VCE=3.6V, VIN=VOUT(T)+0.3V VOUT=OPEN VBIAS=VCE=3.6V, VIN=VOUT(T)+0.3V VOUT=OPEN VOUT(T)≧1.0V VBIAS=VCE =3.6V, VIN=VOUT(T) VOUT= VOUT(T) - 0.05V VOUT(T)＜1.0V VBIAS=VCE =3.6V, VIN=1.0V VOUT= VOUT(T) - 0.05V VBIAS=6.0V, VIN=3.0V, VCE=VSS VBIAS=6.0V, VIN=3.0V, VCE=VSS VOUT(T)≧1.3V VOUT(T)+1.2V≦VBIAS≦6.0V, VIN=VOUT(T)+0.3V, VCE =VBIAS , IOUT=1mA VOUT(T)＜1.3V 2.5V≦VBIAS≦6.0V, VIN=VOUT(T)+0.3V, VCE =VBIAS , IOUT=1mA VOUT(T)≧0.90V, VOUT(T)+0.1V≦VIN≦3.0V, VBIAS=VCE=3.6V, IOUT=1mA V OUT(T)＜0.90V, 1.0V≦VIN≦3.0V VBIAS=VCE=3.6V, IOUT=1mA VCE =VBIAS, VIN =VOUT(T)+0.3V, IOUT=1mA VBIAS=VCE=3.6V, IOUT=1mA VBIAS= VCE =3.6VDC+0.2Vp-pAC, VIN=VOUT(T)+0.3V, IOUT=30mA,f=1kHz VIN=VOUT(T)+0.3VDC+0.2Vp-pAC, VBIAS=3.6V, IOUT=30mA, f=1kHz MAX. 6.0 3.0 +0.02 UNITS CIRCUIT V V V mA mA mA mV mV mV mV mV ① ① Output Voltage Maximum Output Current 1 Maximum Output Current 2 Maximum Output Current 3 Load Regulation Dropout Voltage 1 Dropout Voltage 2 Dropout Voltage 3 Dropout Voltage 4 Supply Current 1 Supply Current 2 ① ① ① ① ① ① ① ① ① ① ① 200 300 400 - 8 E-1 E-2 E-3 E-4 (*6) (*6) (*6) (*6) 17 8 0.1 25 1.0 45 3.0 μA μA Bias Current (*10) IBIASMAX - 1.0 2.5 mA ① Stand-by Current 1 Stand-by Current 2 IBIAS_STB IIN_STB - 0.01 0.01 0.10 0.35 μA μA ① ① Bias Regulation △VOUT/ △VBIAS・VOUT - 0.01 0.3 %/V ① Input Regulation △VOUT/ △VIN・VOUT - 0.01 0.1 %/V ① Bias Voltage UVLO Input Voltage UVLO VBIAS Ripple Rejection VIN Ripple Rejection VBIAS_UVLO VIN_UVLO VBIAS_PSRR VIN_PSRR 1.37 0.07 - 2.0 0.4 40 60 2.5 0.6 - V V dB dB ① ① ② ② 5/32 XC6601 Series ■ELECTRICAL CHARACTERISTICS (Continued) PARAMETER Output Voltage Temperature Characteristics Limit Current Short Current Thermal Shutdown Detect Temperature Thermal Shutdown Release Temperature Hysteresis Width CL Auto-Discharge Resistance CE "H" Level Voltage CE "L" Level Voltage CE "H" Level Current (A Series) CE "H" Level Current (B Series) CE "L" Level Current SYNBOL △VOUT/ △Topr・VOUT ILIM ISHORT TTSD TTSR TTSD−TTSR Rdischg VCEH VCEL ICEH VBIAS=3.6V, VIN= VOUT(T)+0.3V, VCE= VSS, VOUT=VOUT(T) VBIAS=3.6V, VIN= VOUT(T)+0.3V VBIAS=3.6V, VIN= VOUT(T)+0.3V VBIAS=VCE=6.0V, VIN=VOUT(T)+0.3V VBIAS=6.0V, VCE=VSS VIN=VOUT(T)+0.3V CONDITIONS VBIAS=VCE=3.6V, VIN=VOUT(T)+0.3V , IOUT=30mA, - 40℃≦ Topr ≦85℃ VOUT=VOUT(E)×0.95, VBIAS=VCE=3.6V, VIN=VOUT(T)+0.3V VBIAS=VCE=3.6V, VIN=VOUT(T)+0.3V, VOUT=0V Junction Temperature Junction Temperature MIN. 400 290 0.75 2.4 -0.1 -0.1 TYP. ±100 550 80 150 125 25 430 MAX. 610 6.0 0.16 8.0 μA 0.1 0.1 μA ① ① Ta=25 ℃ UNITS CIRCUIT ppm/℃ mA mA ℃ ℃ ℃ Ω V V ① ① ① ① ① ① ① ① ① ICEL NOTE: (*3) * 1: Please use Bias voltage VBIAS within the range VBIAS –VOUT(E) ≧1.2V * 2: Please use Input voltage VIN within the range VIN≦VBIAS * 3: VOUT(E) = Effective output voltage (Refer to the voltage chart E-0 and E-1) * 4: VOUT (T) = Specified output voltage * 5: E-0 = Please refer to the table named OUTPUT VOLTAGE CHART * 6: E-1 = Please refer to the table named DROPOUT VOLTAGE CHART (*8) (*9) * 7: Vdif = {VIN1 -VOUT1 }. * 8: VIN1 = The input voltage when VOUT1 appears as input voltage is gradually decreased. * 9: VOUT1 = A voltage equal to 98% of the output voltage while maintaining an amply stabilized output voltage when VIN=VBIAS at VBIAS