XC9263/XC9264 Series is Not Recommended for New Designs.
XC9263/XC9264 Series
ETR05047-007
18V Operation 0.5A Synchronous Step-Down DC/DC Converters
■GENERAL DESCRIPTION
The XC9263/XC9264 series are 18V operation synchronous step-down DC/DC converter ICs with a built-in high-side / low-side
driver transistor. The XC9263/XC9264 series has operating voltage range of 3.0V~18.0V and it can support 500mA as an output
current with high-efficiency. Compatible with Low ESR capacitors such as ceramic capacitors for the load capacitor (CL).
0.75V reference voltage source is incorporated in the IC, and the output voltage can be set to a value from 1.0V to 15.0V using
external resistors (RFB1, RFB2).
500kHz or 1.2MHz or 2.2MHz can be selected for the switching frequency. In PWM/PFM automatic switchover control, IC can
change the control method between PWM and PFM based on the output current requirement and as a result IC can achieve high
efficiency over the full load range.
XC9263/64 has a fixed internal soft start time which is 1.0ms (TYP.), additionally the time can be extended by using an external
resistor and capacitor.
With the built-in UVLO function, the driver transistor is forced OFF when input voltage goes down to 2.7V or lower.
The output state can be monitored using the power good function.
Over current protection and thermal shutdown are embedded and they secure a safety operation.
■FEATURES
■APPLICATIONS
● Hot water supply system
● Recorders, Camcorders
● Refrigerators, Air-conditioners
● Low Power Systems
Input Voltage Range
:
3.0 ~ 18V (Absolute Max 20V)
FB Voltage
:
0.75V±1.5%
Oscillation Frequency
:
500kHz, 1.2MHz, 2.2MHz
Output Current
:
500mA
Control Methods
:
PWM/PFM Auto
Efficiency 85%@12V→5V, 1mA
PWM control
Soft-start Time
:
Adjustable by RC
Protection Circuits
:
Over Current Protection
Automatic Recovery (B Type)
Integral Latch Method (A Type)
Thermal Shutdown
Output Capacitor
:
Ceramic Capacitor
Package
:
SOT-25 (No Power good)
USP-6C (With Power Good)
Environmentally Friendly
■TYPICAL APPLICATION CIRCUIT
:
EU RoHS Compliant, Pb Free
■TYPICAL PERFORMANCE
CHARACTERISTICS
XC9264x75C
(V IN=12V, V OUT =5V, fOSC=1200kHz)
L
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
Lx
CIN
CFB
EN/SS
90
FB
CL
RFB2
RPG
GN D
PG
CL=10μF×2 (GRM188R61E106MA73)
100
RFB1
Efficiency :EFFI[%]
VIN
80
70
60
50
40
30
20
XC9264x75C
10
0
0.1
1
10
100
Output Current :IOUT[mA]
1/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■BLOCK DIAGRAM
VIN
Current
SENSE
LocalReg
EN/SS
Chip
Enable
each
circuit
Thermal
Shutdown
Current
Limit
PFM
High
Side
Buffer
Operation
Enable
Lx
Low
Side
Buffer
each
circuit
+
+
Err Amp
FB
Current
Limit
Gate
CLAMP
Under
Voltage
Lock Out
Vref
Soft Start
Current
feed
back
PWM
Comparator
-
PWM/PFM
ControlLOGIC
-
GND
OSC
Ramp
Wave
PG(USP-6C Package Only)
+
PowerGood
Comparator
*Diodes inside the circuit are an ESD protection diodes and a parasitic diodes.
2/30
XC9263/XC9264
XC9263/XC9264 Series is Not Recommended for New Designs.
Series
■PRODUCT CLASSIFICATION
●Ordering Information
XC9263①②③④⑤⑥-⑦(*1)
XC9264①②③④⑤⑥-⑦(*1)
PWM control
PWM/PFM Auto
DESIGNATOR
ITEM
①
Type
②③
FB Voltage
SYMBOL
A
Refer to Selection Guide
B
Oscillation Frequency
④
75
Output voltage can be adjusted in 1V to 15V
5
500kHz
C
1.2MHz
D
⑤⑥-⑦
(*1)
Packages (Order Unit)
DESCRIPTION
2.2MHz
MR-G
(*1)
SOT-25 (3,000pcs/Reel)
ER-G(*1)
USP-6C (3,000pcs/Reel)
The “-G” suffix denotes Halogen and Antimony free as well as being fully EU RoHS compliant.
●Selection Guide
FUNCTION
A TYPE
B TYPE
SOT-25
USP-6C
SOT-25
USP-6C
Chip Enable
Yes
Yes
Yes
Yes
UVLO
Yes
Yes
Yes
Yes
Thermal Shutdown
Yes
Yes
Yes
Yes
Soft Start
Yes
Yes
Yes
Yes
Power-Good
-
Yes
-
Yes
-
Yes
Yes
Yes
-
-
Current Limiter
(Automatic Recovery)
Current Limiter
Yes
(Latch Protection (*2) )
(*2) The over-current protection latch is an integral latch type.
3/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■PIN CONFIGURATION
Lx
FB
5
4
1
2
3
VIN
GND
EN/SS
VIN
6
1
Lx
EN/SS
5
2
GND
PG
4
3
FB
USP-6C
(BOTTOM VIEW)
SOT-25
(TOP VIEW)
* The dissipation pad for the USP-6C package should be solder-plated in recommended mount pattern and metal masking so
as to enhance mounting strength and heat release. If the pad needs to be connected to other pins, it should be connected
to the GND (No. 2) pin.
■PIN ASSIGNMENT
PIN NUMBER
PIN NAME
FUNCTION
6
VIN
Power Input
3
5
EN/SS
Enable Soft-start
-
4
PG
Power good Output
4
3
FB
Output Voltage Sense
2
2
GND
Ground
5
1
Lx
Switching Output
SOT-25
USP-6C
1
4/30
XC9263/XC9264 Series is Not Recommended for New Designs.
XC9263/XC9264
Series
■FUNCTION CHART
PIN NAME
EN/SS
(*1)
SIGNAL
STATUS
L
Stand-by
H
Active
OPEN
Undefined State(*1)
Please do not leave the EN/SS pin open. Each should have a certain voltage.
PIN NAME
CONDITION
PG
SIGNAL
VFB > VPGDET
H (High impedance)
VFB ≦ VPGDET
L (Low impedance)
EN/SS = H
Thermal Shutdown
L (Low impedance)
EN/SS = L
UVLO
(VIN < VUVLO1)
Stand-by
Undefined State
L (Low impedance)
■ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
RATINGS
UNITS
VIN Pin Voltage
VIN
-0.3 ~ 20
V
EN/SS Pin Voltage
VEN/SS
-0.3 ~ 20
V
FB Pin Voltage
VFB
-0.3 ~ 6.2
V
PG Pin Voltage
(*1)
VPG
-0.3 ~ 6.2
V
PG Pin Current
(*1)
IPG
8
Lx Pin Voltage
VLx
Lx Pin Current
ILx
-0.3 ~ VIN + 0.3 or 20
mA
(*2)
1800
V
mA
250
Power
Dissipation
(Ta=25℃)
600 (40mm x 40mm Standard board) (*3)
SOT-25
760 (JESD51-7 Board) (*3)
Pd
USP-6C
120
mW
1000 (40mm x 40mm Standard board) (*3)
1250 (JESD51-7 Board) (*3)
Operating Ambient
Temperature
Topr
-40 ~ 105
℃
Storage Temperature
Tstg
-55 ~ 125
℃
* All voltages are described based on the GND pin.
(*1)
For the USP-6C Package only.
(*2)
The maximum value should be either VIN+0.3V or 20V in the lowest.
(*3)
The power dissipation figure shown is PCB mounted and is for reference only.
Please refer to PACKAGING INFORMATION for the mounting condition.
5/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■ELECTRICAL CHARACTERISTICS
Ta=25℃
PARAMETER
SYMBOL
FB Voltage
VFB
Output Voltage Setting Range(*1)
VOUTSET
Operating Voltage Range
VIN
UVLO Detect Voltage
VUVLO1
CONDITIONS
MIN
TYP
MAX
UNIT
CIRCUIT
0.739
0.750
0.761
V
②
-
1
-
15
V
-
-
3
-
18
V
-
2.60
2.70
2.80
V
②
2.70
2.80
2.90
V
②
VFB=0.739V → 0.761V
VFB Voltage when Lx pin oscillates
VIN:2.8V→2.6V, VFB=0.675V
VIN Voltage when Lx pin voltage changes from
"H" level to "L" level
VIN:2.7V→2.9V, VFB=0.675V
UVLO Release Voltage
VUVLO2
VIN Voltage when Lx pin voltage changes from
"L" level to "H" level
Quiescent Current
Stand-by Current
Oscillation Frequency
Iq
ISTB
fOSC
VFB=0.825V
XC9264x755
-
11.5
16.5
μA
④
XC9264x75C
-
12.5
17.5
μA
④
XC9264x75D
-
13.5
18.5
μA
④
-
1.65
2.5
μA
⑤
XC926xx755
458
500
542
kHz
①
XC926xx75C
1098
1200
1302
kHz
①
XC926xx75D
2013
2200
2387
kHz
①
VEN/SS=0V
Connected to external components、
IOUT=100mA
Minimum Duty Cycle
DMIN
VFB=0.825V
-
-
0
%
②
Maximum Duty Cycle
DMAX
VFB=0.675V
100
-
-
%
②
Lx SW "H" On Resistance
RLxH
VFB=0.675V, ILX=200mA
Lx SW "L" On Resistance
RLxL
VFB=0.825V, ILX=200mA
PFM Switch Current
High-side Current Limit (*3)
IPFM
ILIMH
Latch Time
tLAT
Internal Soft-Start Time
tSS1
External Soft-Start Time
tSS2
Connected to external components、
IOUT=1mA
USP-6C
-
0.95
1.10
Ω
②
SOT-25
-
0.99
1.14
Ω
②
USP-6C
-
0.69(*2)
-
Ω
②
0.73
②
SOT-25
-
-
Ω
XC9264x755
-
380
-
mA
XC9264x75C
-
420
-
mA
XC9264x75D
-
370
-
mA
920
1100
-
mA
②
0.5
1.0
1.7
ms
⑥
0.5
1.0
1.7
ms
②
17
26
35
ms
③
0.638
0.675
0.712
V
②
-
-
0.3
V
②
-
85
-
%
①
-
±100
-
ppm/℃
②
VFB=0.675V
Type A only, Connected to external components、
VFB=0V
VEN/SS=0V→12V,VFB=0.675V
Time until Lx pin oscillates
(*2)
①
VEN/SS=0V→12V,VFB=0.675V
RSS=430KΩ,CSS=0.47μF
Time until Lx pin oscillates
VFB=0.712V→0.638V、RPG:100kΩ pull-up to 5V
PG Detect Voltage(*4)
VPGDET
VFB Voltage when PG pin voltage changes from
"H" level to "L" level
PG Output Voltage(*4)
VPG
Efficiency (*5)
EFFI
FB Voltage
ΔVFB/
Temperature Characteristics
(ΔTopr・VFB)
VFB=0.6V, IPG=1mA
Connected to external components、
VOUT=5V, IOUT=1mA
-40℃≦Ta≦105℃
Test Condition: Unless otherwise stated, VIN=12V, VEN/SS=12V
(*1)
: Please use within the range of VOUT/VIN≧0.12 (fosc=500kHz), VOUT/VIN≧0.14 (fosc=1.2MHz), VOUT/VIN≧0.17 (fosc=2.2MHz)
(*2)
: Design reference value. This parameter is provided only for reference.
(*3)
: Current limit denotes the level of detection at peak of coil current.
(*4)
: For the USP-6C Package only.
(*5)
: EFFI = {(output voltage) x (output current)} / {(input voltage) x (input current)} x 100
6/30
XC9263/XC9264
XC9263/XC9264 Series is Not Recommended for New Designs.
Series
■ELECTRICAL CHARACTERISTICS (Continued)
Ta=25℃
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNIT
CIRCUIT
FB ‘H’ Current
IFBH
FB ‘L’ Current
IFBL
VIN=VEN/SS=18V, VFB=3.0V
-0.1
-
0.1
μA
④
VIN=VEN/SS=18V, VFB=0V
-0.1
-
0.1
μA
EN/SS ‘H’ Current
IEN/SSH
VIN=VEN/SS=18V, VFB=0.825V
④
-
0.1
0.3
μA
EN/SS ‘L’ Current
IEN/SSL
VIN=18V, VEN/SS=0V, VFB=0.825V
④
-0.1
-
0.1
μA
④
EN/SS ‘H’ Voltage
VEN/SSH
VEN/SS Voltage when Lx pin voltage changes from
2.5
-
18
V
②
-
-
0.3
V
②
VEN/SS=0.3V→2.5V, VFB=0.71V
"L" level to "H"
VEN/SS=2.5V→0.3V, VFB=0.71V
EN/SS ‘L’ Voltage
VEN/SSL
VEN/SS Voltage when Lx pin voltage changes from
"H" level to "L"
Thermal Shutdown
Temperature
Hysteresis Width
TTSD
Junction Temperature
-
150
-
℃
-
THYS
Junction Temperature
-
25
-
℃
-
Test Condition: Unless otherwise stated, VIN=12V, VEN/SS=12V
7/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■TEST CIRCUITS
CIRCUIT①
VIN
A
Probe
EN/SS
L=2.2μH(fos c=2.2MHz )
L=4.7μH(fos c=1.2MHz )
L=1 0μH(fos c=5 00 kH z)
L
V
V OUT
Lx
2.2μF
V
PG
C FB
A
R FB1
FB
1 0μF
1 0μF
V
R FB2
GND
CIRCUIT②
Probe
VIN
V
Probe
EN/SS
2.2μF
Lx
1 00 kΩ
V
PG
FB
V
A
V
GND
A
1.2kΩ
V
Probe
CIRCUIT③
Probe
VIN
4 30 kΩ
V
Probe
EN/SS
Lx
2.2μF
V
0.4 7μF
PG
FB
GND
* PG Pin is USP-6C Package only.
8/30
V
V
1.2kΩ
XC9263/XC9264
XC9263/XC9264 Series is Not Recommended for New Designs.
Series
■TEST CIRCUITS (Continued)
CIRCUIT④
VIN
A
EN/SS
A
Lx
V
V
PG
FB
A
GND
V
CIRCUIT⑤
VIN
A
EN/SS
Lx
V
PG
FB
V
GND
CIRCUIT⑥
VIN
L=2.2μH(fos c=2.2MHz )
L=4.7μH(fos c=1.2MHz )
L=1 0μH(fos c=5 00 kH z)
Probe
EN/SS
L
V
Lx
2.2μF
V
PG
C FB
R FB1
FB
GND
1 0μF
R FB2
1 0μF
V
* PG Pin is USP-6C Package only.
9/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■TYPICAL APPLICATION CIRCUIT / Parts Selection Method
L
VIN
Lx
CIN
CFB
EN/SS
RFB1
FB
CL
RFB2
RPG
GN D
PG
【Typical Examples】
Oscillation Frequency
500kHz
L
1.2MHz
2.2MHz
CIN
CL
MANUFACTU
RER
PRODUCT NUMBER
TDK
CLF6045NIT-100M
Taiyo Yuden
NRS5040T100MMGJ
Tokyo Coil
SHP0530P-F100AP
TDK
CLF6045NIT-4R7N
TDK
VLS252012CX-4R7M-1
Taiyo Yuden
NRS5024T4R7MMGJ
Tokyo Coil
SHP0530P-F4R7AP
TDK
CLF6045NIT-2R2N
TDK
VLS252012CX-2R2M-1
Taiyo Yuden
NRS4018T2R2MDGJ
Tokyo Coil
VALUE
10μH
4.7μH
2.2μH
500kHz, 1.2MHz, 2.2MHz
Murata
SHP0420P-F2R2NAP
GRM188R61H225KE11
2.2μF / 50V
500kHz
Murata
GRM21BZ71E106KE15
10μF / 25V 2parallel
1.2MHz, 2.2MHz
Murata
GRM188R61E106MA73
10μF / 25V 2parallel
The output voltage can be set by adding an external dividing resistor.
The output voltage is determined by the equation below based on the values of RFB1 and RFB2.
VOUT=VFB×(RFB1+RFB2)/RFB2
With RFB1+RFB2≦1MΩ
Adjust the value of the phase compensation speed-up capacitor CFB using the equation below.
C FB =
1
2π × fzfb × RFB1
* When fosc=500kHz or 1.2MHz, a target value for fzfb of about
is optimum.
1
2π C L × L
* When fosc=2.2MHz, a target value for fzfb of about 5kHz is optimum.
【Setting Example】
To set output voltage to 5V with fosc=500kHz, CL=20μF, L=10μH
When RFB1=680kΩ, RFB2=120kΩ, VOUT=0.75V×(680kΩ+120kΩ) / 120kΩ=5.0V
And fzfb is set to a target of 11.25kHz using the above equation,
CFB=1/(2×π×11.25kHz×680kΩ)=20.8pF
* The setting range for the output voltage is 1.0V to 15.0V.
The condition VOUT/VIN ≧ 0.12 (fosc=500kHz), VOUT/VIN ≧ 0.14 (fosc=1.2MHz), VOUT/VIN ≧ 0.17 (fosc=2.2MHz) must be satisfied.
10/30
XC9263/XC9264 Series is Not Recommended for New Designs.
XC9263/XC9264
Series
■TYPICAL APPLICATION CIRCUIT / Parts Selection Method (Continued)
The soft-start time can be adjusted by adding a capacitor and a resistor to the EN/SS pin.
Soft-start time(tss2) is approximated by the equation below according to values of VEN/SS, RSS, and CSS.
tss2=Css×Rss×( -ln( (VEN/SS-1.45)/VEN/SS ) )
【Setting Example】
When CSS=0.47μF, RSS=430kΩ and VEN/SS=12V, tSS2=0.47x10-6 x 430 x 103 x (-ln((12-1.45)/12))=26ms (Approx.)
*The soft-start time is the time from the start of VEN/SS until the output voltage reaches 90% of the set voltage.
If the EN/SS pin voltage rises steeply without connecting CSS and RSS (RSS=0Ω), Output rises with taking
the soft-start time of tss1=1.0ms (TYP.) which is fixed internally.
VEN/SS
RSS
EN/SS
VEN/SS
CSS
90 % of se tting voltage
VOUT
tSS1
tSS2
11/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■OPERATIONAL EXPLANATION
The XC9263/XC9264 series consists internally of a reference voltage supply with soft-start function, error amp, PWM comparator,
ramp wave circuit, oscillator (OSC) circuit, phase compensation (Current feedback) circuit, current limiting circuit, current limit
PFM circuit, High-side driver Tr., Low-side driver Tr., buffer drive circuit, internal power supply (LocalReg) circuit, under-voltage
lockout (UVLO) circuit, gate clamp (CLAMP) circuit, thermal shutdown (TSD) circuit, power good comparator, control block and
other elements.
The voltage feedback from the FB pin is compared to the internal reference voltage by the error amp, the output from the error
amp is phase compensated, and the signal is input to the PWM comparator to determine the ON time of switching during PWM
operation. The output signal from the error amp is compared to the ramp wave by the PWM comparator, and the output is sent to
the buffer drive circuit and output from the LX pin as the duty width of switching. This operation is performed continuously to
stabilize the output voltage.
The driver transistor current is monitored at each switching by the phase compensation (Current feedback) circuit, and the output
signal from the error amp is modulated as a multi-feedback signal. This allows a stable feedback system to be obtained even
when a low ESR capacitor such as a ceramic capacitor is used, and this stabilizes the output voltage.
VIN
Current
SENSE
LocalReg
EN/SS
Chip
Enable
each
circuit
Thermal
Shutdown
Current
Limit
PFM
High
Side
Buffer
Operation
Enable
Lx
Low
Side
Buffer
each
circuit
+
+
Err Amp
FB
Current
Limit
Gate
CLAMP
Under
Voltage
Lock Out
Vref
Soft Start
Current
feed
back
PWM
Comparator
-
PWM/PFM
ControlLOGIC
-
GND
OSC
Ramp
Wave
PG(USP-6C Package Only)
+
PowerGood
Comparator
*Diodes inside the circuit are an ESD protection diodes and a parasitic diodes.
The reference voltage source provides the reference voltage to ensure stable output voltage of the DC/DC converter.
The ramp wave circuit determines switching frequency. 500kHz or 1.2MHz or 2.2MHz is available for the switching frequency.
Clock pulses generated in this circuit are used to produce ramp waveforms needed for PWM operation.
The error amplifier is designed to monitor output voltage. The amplifier compares the reference voltage with the feedback
voltage divided by the internal voltage divider, RFB1 and RFB2. When a voltage is lower than the reference voltage, then the
voltage is fed back, the output voltage of the error amplifier increases. The error amplifier output is fixed internally to deliver an
optimized signal to the mixer.
12/30
XC9263/XC9264 Series is Not Recommended for New Designs.
XC9263/XC9264
Series
■OPERATIONAL EXPLANATION (Continued)
The current limiting circuit of the XC9263/XC9264 series monitors the current that flows through the High-side driver transistor
and Low-side driver transistor, and when over-current is detected, the current limiting function activates.
①High-side driver Tr. current limiting
The current in the High-side driver Tr. is detected to equivalently monitor the peak value of the coil current. The High-side driver
Tr. current limiting function forcibly turns off the High-side driver Tr. when the peak value of the coil current reaches the High-side
driver current limit value ILIMH. When the over-current state is released, normal operation resumes.
②Low-side driver Tr. current limiting
The current in the Low-side driver Tr. is detected to equivalently monitor the bottom value of the coil current. The Low-side driver
Tr. current limiting function prohibits the High-side driver Tr. from turning on in an over-current state where the bottom value of the
coil current is higher than the Low-side driver Tr. current limit value ILIML(TYP. 0.9A). Control to lower the switching frequency fOSC
is also performed. When the over-current state is released, normal operation resumes.
③ Over-current latch (Type A)
Type A turns off the High-side and Low-side driver Tr. when state ① or ② continues for tLAT (TYP. 1.0ms). The LX pin is latchstopped at the GND level (0V).
The latch-stopped state only stops the pulse output from the Lx pin; the internal circuitry of the IC continues to operate. To restart
after latch-stopping, L level and then H level must be input into the EN/SS pin, or VIN pin re-input must be performed (after
lowering the voltage below the UVLO detection voltage) to resume operation by soft start.
The over-current latch function may occasionally be released from the current limit detection state by the effects of ambient noise,
and it may also happen that the latch time becomes longer or latching does not take place due to board conditions. For this reason,
place the input capacitor as close as possible to the IC.
Type B is an automatic recovery type that performs the operation of ① or ② until the over-current state is released.
tLAT (TYP. 1ms)
Latch Protection (Type A)
ILIMH (TYP. 1.1A)
ILIML (TYP. 0.9A)
ILX
VLX
VOUT
VEN/SS
Current limiting timing chart
13/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■OPERATIONAL EXPLANATION (Continued)
The reference voltage applied to the error amplifier is restricted by the start-up voltage of the EN/SS pin. This ensures that the
error amplifier operates with its two inputs in balance, thereby preventing ON-time signal from becoming longer than necessary.
Therefore, start-up time of the EN/SS pin becomes the set-time of soft-start. The soft-start time can be adjusted by adding a
capacitor and a resistor to the EN/SS pin.
If the EN/SS pin voltage rises steeply without connecting CSS and RSS (RSS=0Ω), Output rises with taking the soft-start time of
tss1=1.0ms (TYP.) which is fixed internally.
The soft-start function operates when the voltage at the EN/SS pin is between 0.3V to 2.5V. If the voltage at the EN/SS pin does
not start from 0V but from a middle level voltage when the power is switched on, the soft-start function will become ineffective and
the possibilities of large inrush currents and ripple voltages occurring will be increased.
The thermal shutdown (TSD) as an over current limit is built in the XC9263/XC9264 series.
When the junction temperature reaches the detection temperature, the driver transistor is forcibly turned off. When the junction
temperature falls
to the release temperature while in the output stop state, restart takes place by soft-start.
This is a function to monitor the internal power supply and to prevent the output of false pulses from the Lx pin when the output
from the internal power supply is unstable at low voltages. As the VIN pin voltage goes down, the internal power supply voltage
falls. So the VIN voltage drops, the UVLO function is activated.
When the VIN pin voltage falls below VUVLO1 (TYP. 2.7V), the UVLO function is activated, the high side driver FET and low side
driver FET are forcibly turned off to prevent false pulse output due to instable operation of the internal circuits. When the VIN pin
voltage rises above VUVLO2 (TYP. 2.8V), the UVLO function is released, the soft start function activates, and output start operation
begins. Stopping by UVLO is not shutdown; only pulse output is stopped and the internal circuits continue to operate.
On USP-6C Package, the output state can be monitored using the power good function.
CONDITION
SIGNAL
VFB > VPGDET
H (High impedance)
VFB ≦ VPGDET
L (Low impedance)
EN/SS = H
Thermal Shutdown
L (Low impedance)
EN/SS = L
UVLO
(VIN < VUVLO1)
Stand-by
Undefined State
L (Low impedance)
The PG pin is an Nch open drain output, therefore a pull-up resistance (approx. 100kΩ) must be connected to the PG pin.
When not using the power good function, connect the PG terminal to GND or use it open.
14/30
XC9263/XC9264
XC9263/XC9264 Series is Not Recommended for New Designs.
Series
■NOTES ON USE
1)
In the case of a temporary and transient voltage drop or voltage rise.
If the absolute maximum ratings are exceeded, the IC may deteriorate or be destroyed.
If a voltage exceeding the absolute maximum voltage is applied to the IC due to chattering caused by a mechanical switch or
an external surge voltage, please use a protection element such as a TVS and a protection circuit as a countermeasure.
Please see the countermeasures from (a) to (c) shown below.
(a) When voltage exceeding the absolute maximum ratings comes into the VIN pin due to the transient change on the power
line, there is a possibility that the IC breaks down in the end.
To prevent such a failure, please add a TVS between VIN and GND as a countermeasure
(b) When the input voltage decreases below the output voltage, there is a possibility that an overcurrent will flow in the IC’s
internal parasitic diode and exceed the absolute maximum rating of the Lx pin.
If the current is pulled into the input side by the low impedance between VIN -GND, then countermeasures, such as adding an
SBD between VOUT-VIN, should be taken.
(c) When a negative voltage is applied to the input voltage by a reverse connection or chattering, an overcurrent could flow in
the IC’s parasitic diode and damage the IC. Take countermeasures, such as adding a reverse touching protection diode
(b)SBD
(c)Reverse-Touching
Protection Diode
L
VIN
(a)TVS
CIN2
Lx
CFB
CIN1
EN/SS
RFB1
FB
RFB2
CL1
CL2
RPG
GN D
2)
PG
Make sure that the absolute maximum ratings of the external components and of this IC are not exceeded.
3) The DC/DC converter characteristics depend greatly on the externally connected components as well as on the characteristics
of this IC, so refer to the specifications and standard circuit examples of each component when carefully considering which
components to select.
Be especially careful of the capacitor characteristics and use B characteristics (JIS standard) or X7R, X5R (EIA standard)
ceramic capacitors.
The capacitance decrease caused by the bias voltage may become remarkable depending on the external size of the
capacitor.
4)
If there is a large dropout voltage, then there might be pulse-skip during light loads even with PWM control.
5)
The DC/DC converter of this IC uses a current-limiting circuit to monitor the coil peak current. If the potential dropout voltage
is large or the load current is large, the peak current will increase, which makes it easier for current limitation to be applied
which in turn could cause the operation to become unstable. When the peak current becomes large, adjust the coil inductance
and sufficiently check the operation.
6)
If there is a large dropout voltage, a circuit delay could create the ramp-up of coil current with staircase waveform exceeding
the current limit.
15/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■NOTES ON USE (Continued)
7) The ripple voltage could be increased when switching from discontinuous conduction mode to Continuous conduction
mode.
Please evaluate IC well on customer’s PCB.
8)
The operation of the IC becomes unstable below the minimum operating voltage.
9)
If the voltage at the EN/SS Pin does not start from 0V but it is at the midpoint potential when the power is switched on, the
soft start function may not work properly and it may cause the larger inrush current and bigger ripple voltages.
10) The effects of ambient noise and the state of the circuit board may cause release from the current limiting state, and the latch
time may lengthen or latch operation may not take place. Please evaluate IC well on customer’s PCB.
11)
In order to drive the IC normally, supply a stable input voltage to the VIN pin after reducing the AC impedance due to the
bypass capacitor. In particular, if the amplitude of the input voltage fluctuates by 2V or more and ±0.1V/μs or more, there
is a possibility that the UVLO function malfunctions due to fluctuations of the internal power supply of the IC.
In that case, switching is stopped in a protected state that prevents false pulse output from the Lx pin. After that, the soft
start function gets started, it shifts to normal operation.
If the input voltage fluctuates momentarily, take measures such as increasing the input capacitance.
12) Instructions of pattern layouts
The operation may become unstable due to noise and/or phase lag from the output current when the wire impedance is
high, please place the input capacitor(CIN) and the output capacitor (CL) as close to the IC as possible.
(1) In order to stabilize VIN voltage level, we recommend that a by-pass capacitor (CIN) be connected as close as possible
to the VIN and GND pins. If fluctuation of the VIN potential is expected, please take measures such as increasing input
capacitor(CIN).
(b)SBD
(c)Reverse-Touching
Protection Diode
L
VIN
(a)TVS
CIN2
Lx
CFB
(1)CIN1
EN/SS
RFB1
FB
RFB2
CL1
CL2
RPG
GN D
PG
(2) Please mount each external component as close to the IC as possible.
Please place the external parts on the same side of the PCB as the IC, not on the reverse side of the PCB and elsewhere.
(3) Wire external components as close to the IC as possible and use thick, short connecting traces to reduce the circuit
Impedance.
(4) Make sure that the GND traces are as thick as possible, as variations in ground potential caused by high ground
currents at the time of switching may result in instability of the IC.
(5) Please note that internal driver transistors bring on heat because of the load current and ON resistance of High-side driver
transistor, Low-side driver transistor
16/30
XC9263/XC9264 Series is Not Recommended for New Designs.
XC9263/XC9264
Series
■NOTES ON USE (Continued)
SOT-25(Front)
USP-6C(Front)
SOT-25(Back)
USP-6C(Back)
12) Torex places an importance on improving our products and their reliability. We request that users incorporate fail-safe designs
and post-aging protection treatment when using Torex products in their systems.
17/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■TYPICAL PERFORMANCE CHARACTERISTICS
(1) Efficiency vs. Output current
XC9263x755/XC9264x755
XC9263x755/XC9264x755
(VIN=12V, VOUT=3.3V, fOSC=500kHz)
(VIN=12V, VOUT=5V, fOSC=500kHz)
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
100
100
90
90
80
80
70
60
50
40
30
20
XC9263x755
10
XC9264x755
Efficiency :EFFI[%]
Efficiency :EFFI[%]
CL=10μF×2 (GRM21BZ71E106KE15)
0
0.1
1
10
70
60
50
40
30
20
XC9263x755
10
XC9264x755
0
100
0.1
Output Current :IOUT[mA]
XC9263x75C/XC9264x75C
(VIN=12V, VOUT=5V, fOSC=1200kHz)
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
100
100
90
90
80
80
70
60
50
40
30
20
XC9263x75C
10
XC9264x75C
Efficiency :EFFI[%]
Efficiency :EFFI[%]
100
(VIN=12V, VOUT=3.3V, fOSC=1200kHz)
0
70
60
50
40
30
20
XC9263x75C
10
XC9264x75C
0
0.1
1
10
100
Output Current :IOUT[mA]
0.1
10
100
XC9263x75D/XC9264x75D
XC9263x75D/XC9264x75D
(VIN=12V, VOUT=3.3V, fOSC=2200kHz)
(VIN=12V, VOUT=5V, fOSC=2200kHz)
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
100
90
90
80
80
70
60
50
40
30
20
XC9263x75D
10
XC9264x75D
0
1
10
Output Current :IOUT[mA]
100
Efficiency :EFFI[%]
100
0.1
1
Output Current :IOUT[mA]
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
Efficiency :EFFI[%]
10
XC9263x75C/XC9264x75C
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
18/30
1
Output Current :IOUT[mA]
70
60
50
40
30
20
XC9263x75D
10
XC9264x75D
0
0.1
1
10
100
Output Current :IOUT[mA]
XC9263/XC9264 Series is Not Recommended for New Designs.
XC9263/XC9264
Series
■TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
(2) Output Voltage vs. Output Current
XC9263x755/XC9264x755
XC9263x755/XC9264x755
(VIN=12V, VOUT=3.3V, fOSC=500kHz)
(VIN=12V, VOUT=5V, fOSC=500kHz)
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
5.30
Output Voltage : VOUT[V]
Output Voltage : VOUT[V]
3.60
3.50
3.40
3.30
3.20
XC9263x755
3.10
XC9264x755
5.20
5.10
5.00
4.90
XC9263x755
4.80
XC9264x755
4.70
3.00
1
10
100
1
1000
10
Output Current :IOUT[mA]
XC9263x75C/XC9264x75C
(VIN=12V, VOUT=3.3V, fOSC=1200kHz)
(VIN=12V, VOUT=5V, fOSC=1200kHz)
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
3.60
5.30
Output Voltage : VOUT[V]
Output Voltage : VOUT[V]
1000
XC9263x75C/XC9264x75C
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
3.50
3.40
3.30
3.20
XC9263x75C
3.10
XC9264x75C
3.00
5.20
5.10
5.00
4.90
XC9263x75C
4.80
XC9264x75C
4.70
10
1
100
1000
10
1
Output Current :IOUT[mA]
100
1000
Output Current :IOUT[mA]
XC9263x75D/XC9264x75D
XC9263x75D/XC9264x75D
(VIN=12V, VOUT=3.3V, fOSC=2200kHz)
(VIN=12V, VOUT=5V, fOSC=2200kHz)
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
3.60
5.30
Output Voltage : VOUT[V]
Output Voltage : VOUT[V]
100
Output Current :IOUT[mA]
3.50
3.40
3.30
3.20
XC9263x75D
3.10
XC9264x75D
5.20
5.10
5.00
4.90
XC9263x75D
4.80
XC9264x75D
4.70
3.00
1
10
100
Output Current :IOUT[mA]
1000
1
10
100
1000
Output Current :IOUT[mA]
19/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
(3) Ripple Voltage vs. Output Current
XC9263x75C/XC9264x75C
(VIN=12V, VOUT=5V, fOSC=500kHz)
(VIN=12V, VOUT=5V, fOSC=1200kHz)
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
100
100
90
XC9263x755
80
XC9264x755
Ripple Voltage :Vr[mV]
Ripple Voltage :Vr[mV]
XC9263x755/XC9264x755
70
60
50
40
30
20
10
90
XC9263x75C
80
XC9264x75C
70
60
50
40
30
20
10
0
1
0.1
10
0
100
0.1
1
Output Current :IOUT[mA]
10
100
Output Current :IOUT[mA]
XC9263x75D/XC9264x75D
(VIN=12V, VOUT=5V, fOSC=2200kHz)
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
Ripple Voltage :Vr[mV]
100
90
XC9263x75D
80
XC9264x75D
70
60
50
40
30
20
10
0
0.1
1
10
100
Output Current :IOUT[mA]
(4) FB Voltage vs. Ambient Temperature
(5) UVLO Voltage vs. Ambient Temperature
XC9263/XC9264
XC9263/XC9264
VIN =12V
0.755
0.750
0.745
0.740
-50
-25
0
25
50
75
Ambient Temperature :Ta[℃]
20/30
3.0
UVLO Voltage :VUVLO1 ,VUVLO2 [V]
FB Voltage :VFB[V]
0.760
100
125
VUVLO1(DetectVoltage)
2.9
VUVLO2(ReleaseVoltage)
2.8
2.7
2.6
2.5
-50
-25
0
25
50
75
Ambient Temperature :Ta[℃]
100
125
XC9263/XC9264
XC9263/XC9264 Series is Not Recommended for New Designs.
Series
■TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
(6) Oscillation Frequency vs. Ambient Temperature
XC9263x75C/XC9264x75C
XC9263x755/XC9264x755
(fOSC=1200kHz)
(fOSC=500kHz)
VIN =12V
550
500
450
VIN =12V
1440
Oscillation Frequency:fOSC [kHz]
Oscillation Frequency:fOSC [kHz]
600
400
1360
1280
1200
1120
1040
960
-50
-25
0
25
50
75
100
125
-50
-25
Ambient Temperature :Ta[℃]
0
25
50
75
100
125
Ambient Temperature :Ta[℃]
XC9263x75D/XC9264x75D
(fOSC=2200kHz)
VIN =12V
Oscillation Frequency:fOSC [kHz]
2650
2500
2350
2200
2050
1900
1750
-50
-25
0
25
50
75
100
125
Ambient Temperature :Ta[℃]
(7) Stand-by Current vs. Ambient Temperature
(8) Lx SW ON Resistance vs. Ambient Temperature
XC9263/XC9264
XC9263/XC9264
VIN =12V
VIN =12V
2.0
Lx SW ON Resistance :RON[Ω]
Stand-by Current :ISTB[μA]
4.0
3.0
2.0
1.0
0.0
-50
-25
0
25
50
75
Ambient Temperature :Ta[℃]
100
125
1.5
1.0
0.5
Hig hs ide SW .
Lows ide SW .
0.0
-50
-25
0
25
50
75
100
125
Ambient Temperature :Ta[℃]
21/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
(9) Quiescent Current vs. Ambient Temperature
XC9263x755/XC9264x755
XC9263x75C/XC9264x75C
(fOSC=500kHz)
(fOSC=1200kHz)
VIN =12V
200
VIN =12V
200
XC9263x75C
Quiescent Current :Iq[uA]
Quiescent Current :Iq[uA]
XC9263x755
XC9264x755
150
100
50
0
XC9264x75C
150
100
50
0
-50
0
-25
25
50
75
100
125
-50
0
-25
Ambient Temperature :Ta[℃]
25
50
75
100
125
Ambient Temperature :Ta[℃]
XC9263x75D/XC9264x75D
(fOSC=2200kHz)
VIN =12V
Quiescent Current :Iq[uA]
200
XC9263x75D
XC9264x75D
150
100
50
0
-50
-25
0
25
50
75
100
125
Ambient Temperature :Ta[℃]
(10) Internal Soft-Start Time vs. Ambient Temperature
(11) External Soft-Start Time vs. Ambient Temperature
XC9263/XC9264
XC9263/XC9264
VIN =12V
1.5
1.0
0.5
0.0
-50
-25
0
25
50
75
Ambient Temperature :Ta[℃]
22/30
100
125
VIN=12V, RSS=430kΩ, CSS=0.47μF
35
External lSoft-StartTime :tSS2 [ms]
Internal Soft-StartTime :tSS1 [ms]
2.0
30
25
20
15
-50
-25
0
25
50
75
Ambient Temperature :Ta[℃]
100
125
XC9263/XC9264
XC9263/XC9264 Series is Not Recommended for New Designs.
Series
■TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
(12) PFM Current vs. Ambient Temperature
XC9264x75C
XC9264x755
(VIN=12V, VOUT=5V, fOSC=1200kHz)
(VIN=12V, VOUT=5V, fOSC=500kHz)
500
PFM Current :IPFM[mA]
PFM Current :IPFM[mA]
500
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
450
400
350
300
250
-50
-25
0
25
50
75
100
125
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
450
400
350
300
250
-50
-25
Ambient Temperature :Ta[℃]
0
25
50
75
100
125
Ambient Temperature :Ta[℃]
XC9264x75D
(VIN=12V, VOUT=5V, fOSC=2200kHz)
PFM Current :IPFM[mA]
500
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
450
400
350
300
250
-50
-25
0
25
50
75
100
125
Ambient Temperature :Ta[℃]
(13) PG Detect Voltage vs. Ambient Temperature
(14) PG Output Voltage vs. Ambient Temperature
XC9263/XC9264
XC9263/XC9264
VIN =12V
0.70
0.65
0.60
-50
VIN =12V, IPG=1mA
0.4
PG Output Voltage :VPG[V]
PG Detect Voltage :VPGDET[V]
0.75
0.3
0.2
0.1
0.0
-25
0
25
50
75
Ambient Temperature :Ta[℃]
100
125
-50
-25
0
25
50
75
100
125
Ambient Temperature :Ta[℃]
23/30
XC9263/XC9264 Series
XC9263/XC9264 Series is
Not Recommended for New Designs.
■TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
(15) EN/SS Voltage vs. Ambient Temperature
XC9263/XC9264
VIN =12V
4.0
EN/SS"H"
EN/SS Voltage :VCE[V]
EN/SS"L"
3.0
2.0
1.0
0.0
-50
-25
0
25
50
75
Ambient Temperature :Ta[℃]
24/30
100
125
XC9263/XC9264 Series is Not Recommended for New Designs.
XC9263/XC9264
Series
■TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
(16) Load Transient Response
XC9263x755、 fOSC =500kHz
XC9264x755、 fOSC =500kHz
VIN =12V, VOUT=5.0V, IOUT=1mA→300mA
VIN =12V, VOUT=5.0V, IOUT=1mA→300mA
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
1.0ms/div
1.0ms/div
IOUT =1mA→300mA
IOUT =1mA→300mA
V OUT : 500mV/div
V OUT : 500mV/div
XC9263x75C、 fOSC =1200kHz
XC9264x75C、 fOSC =1200kHz
VIN =12V, VOUT=5.0V, IOUT=1mA→300mA
VIN =12V, VOUT=5.0V, IOUT=1mA→300mA
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
CL=10μF×2 (GRM188R61E106MA73)
1.0ms/div
1.0ms/div
IOUT =1mA→300mA
IOUT =1mA→300mA
V OUT : 500mV/div
V OUT : 500mV/div
XC9264x75D、 fOSC =2200kHz
XC9263x75D、 fOSC =2200kHz
VIN =12V, VOUT=5.0V, IOUT=1mA→300mA
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
VIN =12V, VOUT=5.0V, IOUT=1mA→300mA
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
CL=10μF×2 (GRM188R61E106MA73)
1.0ms/div
1.0ms/div
IOUT =1mA→300mA
IOUT =1mA→300mA
V OUT : 500mV/div
V OUT : 500mV/div
25/30
XC9263/XC9264 Series is
Not Recommended for New Designs.
XC9263/XC9264 Series
■TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
(17) Input Transient Response
XC9263x755、 fOSC =500kHz
XC9264x755、 fOSC =500kHz
VIN =12V→18V, VOUT=5V, IOUT=300mA
VIN =12V→18V, VOUT=5V, IOUT=300mA
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
1.0ms/div
1.0ms/div
V N=12V→18V
V N=12V→18V
V OUT : 500mV/div
V OUT : 500mV/div
XC9263x75C、 fOSC =1200kHz
XC9264x75C、 fOSC =1200kHz
VIN =12V→18V, VOUT=5V, IOUT=300mA
VIN =12V→18V, VOUT=5V, IOUT=300mA
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
1.0ms/div
1.0ms/div
V N=12V→18V
V N=12V→18V
V OUT : 500mV/div
V OUT : 500mV/div
XC9263x75D、 fOSC =2200kHz
XC9264x75D、 fOSC =2200kHz
VIN =12V→18V, VOUT=5V, IOUT=300mA
VIN =12V→18V, VOUT=5V, IOUT=300mA
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
1.0ms/div
1.0μs/div
V N=12V→18V
V N=12V→18V
V OUT : 500mV/div
V OUT : 500mV/div
26/30
XC9263/XC9264
XC9263/XC9264 Series is Not Recommended for New Designs.
Series
■TYPICAL PERFORMANCE CHARACTERISTICS(Continued)
(18) EN/SS Rising Response
XC9263x755、 fOSC =500kHz
XC9264x755、 fOSC =500kHz
VIN =12V, VCE=0→12V, VOUT=5V, IOUT=300mA
VIN =12V, VCE=0→12V, VOUT=5V, IOUT=300mA
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
L=10μH(CLF6045NIT-100), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM21BZ71E106KE15)
200μs/div
200μs/div
EN/SS=0V→12V
V OUT : 2V/div
EN/SS=0V→12V
V OUT : 2V/div
XC9263x75C、 fOSC =1200kHz
XC9264x75C、 fOSC =1200kHz
VIN =12V, VCE=0→12V, VOUT=5V, IOUT=300mA
VIN =12V, VCE=0→12V, VOUT=5V, IOUT=300mA
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
L=4.7μH(CLF6045NIT-4R7), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
200μs/div
EN/SS=0V→12V
V OUT : 2V/div
200μs/div
EN/SS=0V→12V
V OUT : 2V/div
XC9263x75D、 fOSC =2200kHz
XC9264x75D、 fOSC =2200kHz
VIN =12V, VCE=0→12V, VOUT=5V, IOUT=300mA
VIN =12V, VCE=0→12V, VOUT=5V, IOUT=300mA
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
L=2.2μH(CLF6045NIT-2R2), CIN =2.2μF(GRM188R61H225KE11),
CL=10μF×2 (GRM188R61E106MA73)
200μs/div
200μs/div
EN/SS=0V→12V
V OUT : 2V/div
EN/SS=0V→12V
V OUT : 2V/div
27/30
XC9263/XC9264 Series
XC9263/XC9264 Series is
Not Recommended for New Designs.
■PACKAGING INFORMATION
For the latest package information go to, www.torexsemi.com/technical-support/packages
PACKAGE
OUTLINE / LAND PATTERN
THERMAL CHARACTERISTICS
SOT-25
SOT-25 PKG
SOT-25 Power Dissipation
USP-6C
USP-6C PKG
USP-6C Power Dissipation
28/30
XC9263/XC9264
XC9263/XC9264 Series is Not Recommended for New Designs.
Series
■MARKING RULE
●SOT-25(Under dot) / USP-6C
SOT-25(Under
●SOT-25
(Under dot)dot仕様)
5
4
●USP-6C
USP-6C
Enlarge
②
③
④
⑤
②
③
3
⑤
2
④
2
1
①
1
①
3
6
5
4
①②③ represents products series, products type, Oscillation Frequency
①
MARK
②
③
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
A
B
C
D
E
F
H
K
L
M
N
P
SERIES
TYPE
OSCILLATION
FREQUENCY
PRODUCT SERIES
XC9263
XC9263
XC9263
XC9263
XC9263
XC9263
XC9264
XC9264
XC9264
XC9264
XC9264
XC9264
A
A
A
B
B
B
A
A
A
B
B
B
5
C
D
5
C
D
5
C
D
5
C
D
XC9263A755xx-G
XC9263A75Cxx-G
XC9263A75Dxx-G
XC9263B755xx-G
XC9263B75Cxx-G
XC9263B75Dxx-G
XC9264A755xx-G
XC9264A75Cxx-G
XC9264A75Dxx-G
XC9264B755xx-G
XC9264B75Cxx-G
XC9264B75Dxx-G
④⑤ represents production lot number
01~09, 0A~0Z, 11~9Z, A1~A9, AA~AZ, B1~ZZ in order.
(G, I, J, O, Q, W excluded)
* No character inversion used.
29/30
XC9263/XC9264 Series
XC9263/XC9264 Series is
Not Recommended for New Designs.
1.
The product and product specifications contained herein are subject to change without notice to
improve performance characteristics. Consult us, or our representatives before use, to confirm that
the information in this datasheet is up to date.
2.
The information in this datasheet is intended to illustrate the operation and characteristics of our
products. We neither make warranties or representations with respect to the accuracy or
completeness of the information contained in this datasheet nor grant any license to any intellectual
property rights of ours or any third party concerning with the information in this datasheet.
3.
Applicable export control laws and regulations should be complied and the procedures required by
such laws and regulations should also be followed, when the product or any information contained in
this datasheet is exported.
4.
The product is neither intended nor warranted for use in equipment of systems which require
extremely high levels of quality and/or reliability and/or a malfunction or failure which may cause loss
of human life, bodily injury, serious property damage including but not limited to devices or equipment
used in 1) nuclear facilities, 2) aerospace industry, 3) medical facilities, 4) automobile industry and
other transportation industry and 5) safety devices and safety equipment to control combustions and
explosions. Do not use the product for the above use unless agreed by us in writing in advance.
5.
Although we make continuous efforts to improve the quality and reliability of our products;
nevertheless Semiconductors are likely to fail with a certain probability. So in order to prevent personal
injury and/or property damage resulting from such failure, customers are required to incorporate
adequate safety measures in their designs, such as system fail safes, redundancy and fire prevention
features.
6.
Our products are not designed to be Radiation-resistant.
7.
Please use the product listed in this datasheet within the specified ranges.
8.
We assume no responsibility for damage or loss due to abnormal use.
9.
All rights reserved. No part of this datasheet may be copied or reproduced unless agreed by Torex
Semiconductor Ltd in writing in advance.
TOREX SEMICONDUCTOR LTD.
30/30