XD6216B401MR-Q

XD6216 Series ETR03098-001d 28V Low Power Consumption 150mA Voltage Regulators (with Stand-by Function) ☆AEC-Q100 Grade2 ■GENERAL DESCRIPTION XD6216 series are positive voltage regulator ICs with 28V of operation voltage. The series consists of a voltage reference, an error amplifier, a current limiter, a thermal shutdown circuit and a phase compensation circuit plus a driver transistor. The output voltage is selectable in 0.1V increments within the range of 1.8V to 12V using laser trimming technologies. The output stabilization capacitor (CL) is also compatible with low ESR ceramic capacitors. The over current protection circuit and the thermal shutdown circuit are built-in. These two protection circuits will operate when the output current reaches current limit level or the junction temperature reaches temperature limit level. The CE function enables the output to be turned off and the IC becomes a stand-by mode resulting in greatly reduced power consumption. ■FEATURES ■APPLICATIONS ● Car navigation systems ● Car audios ● Car-mounted camera ● Other automotive accessories Max Output Current Low Power Consumption Stand-by Current Dropout Voltage : 150mA (VIN=VOUT+3.0V) : 5μA : Less than 0.1μA : 190mV@IOUT=20mA Input Voltage Range Output Voltage Range Fixed Output Accuracy (VOUT=5.0V) : 2.0V ~ 28.0V : 1.8V ~ 12.0V (0.1V Step) : ±1% (VOUT≧2.0V) High Ripple Rejection Built–in Protection Output Capacitor Operating Ambient Temperature Packages Environmentally Friendly ■ TYPICAL APPLICATION CIRCUIT ±20mV (VOUT≦1.9V) : 30dB@1kHz : Current Limit Thermal Shutdown : Ceramic Capacitor Compatible : -40℃~ 105℃ : SOT-25 : SOT-89-5 : EU RoHS Compliant, Pb Free ■TYPICAL PERFORMANCE CHARACTERISTICS XD6216B501 VIN=VCE,CIN=CL=1.0μF(cera mic) 10 9 C IN 1.0uF 8 VOUT CE CL VSS 1.0uF Supply Current : ISS (uA) VIN 7 6 5 4 3 2 Ta=-40℃ Ta=25℃ Ta=105℃ 1 0 0 4 8 12 16 20 Input Voltage : VIN (V) 24 28 1/18 XD6216 Series ■BLOCK DIAGRAMS ●XD6216 Series VIN - Erro r AMP + Curren t Limit VOUT CE ON/OFF Control Thermal Pro tection Voltage Reference VS S R1 R2 *Diodes inside the circuit are an ESD protection diode and parasitic diodes. ■ PRODUCT CLASSIFICATION ●Ordering Information XD6216①②③④⑤⑥-⑦(*1) DESIGNATOR ITEM SYMBOL ① TYPE B ②③ Output Voltage 18~C0 ④ Output Voltage Accuracy ⑤⑥-⑦(*1) Packages (Order Unit) 1 MR-Q PR-Q (*1) DESCRIPTION Refer to Selection Guide For the voltage within 1.8V~9.9V (0.1V increments); e.g. 2.5V ⇒ 25, 5.0V ⇒ 50 For the voltage within 10.0V~12.0V (0.1V increments); e.g. 10.6V ⇒ A6, 11.2V ⇒ B2, 12.0V ⇒ C0 ±1% SOT-25 (3,000pcs/Reel) SOT-89-5 (1,000pcs/Reel) The “-Q” suffix denotes “AEC-Q100” and “Halogen and Antimony free” as well as being fully EU RoHS compliant. ●Selection Guide TYPE CE function B Yes ■STANDARD VOLTAGE ●Examples for standard voltage VOUT 3.3V 5.0V 8.0V PACKAGES SOT-25 SOT-89-5 XD6216B331MR-Q XD6216B501MR-Q XD6216B331PR-Q XD6216B501PR-Q XD6216B801MR-Q XD6216B801PR-Q Output voltages can be set internally from 1.8V to 12.0V. For other voltages, please contact your local Torex sales office or distribution 2/18 XD6216 Series ■PIN CONFIGURATION VOUT CE 5 4 1 2 3 VIN VSS NC VIN SOT-25 SOT-25 (TOP VIEW) (TOP VIEW) NC 5 2 4 1 2 3 VOUT VSS CE SOT-89-5 SOT-89-5 (TOP VIEW) (TOP VIEW) ■PIN ASSIGNMENT PIN NUMBER PIN NAME FUNCTION VIN Power Supply Input SOT-25 SOT-89-5 1 2 5 2 VSS Ground 3 4 NC No Connection 4 3 CE ON/OFF Control 5 1 VOUT Output ■FUNCTION PIN NAME DESIGNATOR IC OPERATION L Stand-by CE H Active OPEN Undefined state* * Please avoid the state of OPEN, and make CE Pin arbitrary fixed potential. ■ABSOLUTE MAXIMUM RATINGS 1) XD6216 Series Ta=25℃ PARAMETER SYMBOL RATINGS UNITS VIN Pin Voltage VIN -0.3 ~ 30.0 V Output Current IOUT Output Voltage VOUT CE Input Voltage VCE 300 (*1) -0.3 ~ VIN+0.3 or 30.0 mA (*2) -0.3 ~ 30.0 V V 250 (IC only) 600 (40mm x 40mm Standard board) (*3) SOT-25 Power Dissipation 760(JESD51-7 board) (*3) Pd 500 (IC only) mW 1300 (40mm x 40mm Standard board) (*3) SOT-89-5 1750 (JESD51-7 board) (*3) Operating Ambient Temperature Topr -40 ~ 105 ℃ Storage Temperature Tstg -55 ~ 125 ℃ All voltages are described based on the VSS. (*1) Please use within the range of IOUT≦Pd/(VIN-VOUT) (*2) The maximum rating corresponds to the lowest value between VIN+0.3V or 30.0V. (*3) The power dissipation figure shown is PCB mounted and is for reference only. Please refer to PACKAGING INFORMATION for the mounting condition. 3/18 XD6216 Series ■ELECTRICAL CHARACTERISTICS Ta=25℃ PARAMETER SYMBOL Output Voltage VOUT(E)(*2) CONDITIONS IOUT=20mA , VCE=VIN IOUTMAX Current (VOUT(T)≧3.0V） VIN=VOUT(T)+3.0V（*1）, VCE=VIN (VOUT(T)＜3.0V) 1mA≦IOUT≦50mA, VCE=VIN Load Regulation △VOUT (VOUT(T)≦7.0V) 1mA≦IOUT≦50mA , VCE=VIN (7.0V＜VOUT(T)) TYP. MAX. E-0 -40℃≦Ta≦105℃（*4） VIN= VOUT(T)+3.0V（*1）, VCE=VIN Maximum Output MIN. 150 - V ① mA ① - 100 - - - 50 90 mV ① - 110 140 mV ① Dropout Voltage1 Vdif1(*3) IOUT=20mA , VCE=VIN - E-1 mV ① Dropout Voltage2 Vdif2(*3) IOUT=100mA ，VCE=VIN - E-2 mV ① Supply Current ISS μA ② Stand-by Current ISTB μA ② Line Regulation1 Line Regulation2 △VOUT / (△VIN・VOUT) △VOUT / (△VIN・VOUT) Input Voltage Output Voltage Temperature Characteristics VCE=VIN -40℃≦Ta≦105℃（*4） VCE=VSS -40℃≦Ta≦105℃（*4） VOUT(T)+2.0V≦VIN≦28.0V IOUT=5mA , VCE=VIN VOUT(T)+2.0V≦VIN≦28.0V IOUT=13mA , VCE=VIN -40℃≦Ta≦105℃（*4） VIN △VOUT / IOUT=20mA , VCE=VIN (△Topr・V OUT) -40℃≦Topr≦105℃ Power Supply PSRR Rejection Ratio VIN=[VOUT(T)+2.0]V+0.5VP-PAC IOUT=20mA , f=1kHz , VCE=VIN 1.0 5.0 9.0 0.3 5.0 10.0 - 0.01 0.10 - - 0.30 - 0.05 0.10 %/V ① - 0.15 0.30 %/V ① 2.0 - 28.0 V - - ±100 - ppm/℃ ① - 30 - dB ③ Short Current ISHORT VCE=VIN, VOUT=VSS - 30 - mA ① CE ”H” Level Voltage VCEH - -40℃≦Ta≦105℃（*4） 1.1 - 28.0 V ④ CE ”L” Level Voltage VCEL - -40℃≦Ta≦105℃（*4） VSS - 0.35 V ④ μA ② CE ”H” Level Current ICEH CE ”L” Level Current ICEL Thermal Shutdown Detect , - 0.1 -0.1 - 0.2 -40℃≦Ta≦105℃（*4） -0.1 - 0.1 μA ② - 150 - ℃ ④ TTSR VCE=VIN , Junction Temperature - 125 - ℃ ④ TTSD-TTSR VCE=VIN , Junction Temperature - 25 - ℃ - Thermal Shutdown Hysteresis Width VIN=28.0V VCE=VSS -0.1 -40℃≦Ta≦105℃（*4） VCE=VIN , Junction Temperature Release Temperature Thermal Shutdown VIN=VCE=28.0V TTSD Temperature Unless otherwise stated, (VIN=VOUT (T) +2.0V). NOTE: (*1) : VOUT(T): Nominal output voltage (*2) : VOUT (E): Effective output voltage (*3) : Vdif= {VIN1 - VOUT1} (i.e. the output voltage when “VOUT (T) +2.0V” is provided at the VIN pin while maintaining a certain IOUT value.) VOUT1: VOUT(T)＜3.0V, A voltage equal to 98% of the output voltage whenever an amply stabilized IOUT {VOUT(T)+3.0V} is input. VOUT(T)≧3.0V, A voltage equal to 98% of the output voltage whenever an amply stabilized IOUT {VOUT(T)+2.0V} is input. VIN1: The input voltage when VOUT1 appears as input voltage is gradually decreased. (*4): UNITS CIRCUIT The ambient temperature range (-40℃≦Ta≦105℃) is design Value. 4/18 XD6216 Series ■ELECTRICAL CHARACTERISTICS (Continued) ●Voltage Chart1 (XD6216 Series) PARAMETER NOMINAL OUTPUT VOLTAGE(V) VOUT(T) E-0 Output Voltage (V) Output Voltage (V) Ta=25℃ -40℃≦Ta≦105℃ VOUT(E) E-1 E-2 DROPOUT VOLTAGE 1 DROPOUT VOLTAGE 2 (mV) (mV) IOUT=20mA IOUT=100mA Ta=25℃ Ta=25℃ VOUT(E) Vdif1 MIN MAX MIN MAX 1.8 1.780 1.820 1.740 1.860 1.9 1.880 1.920 1.840 1.960 2.0 1.980 2.020 1.940 2.060 2.1 2.079 2.121 2.037 2.163 2.2 2.178 2.222 2.134 2.266 2.3 2.277 2.323 2.231 2.369 2.4 2.376 2.424 2.328 2.472 2.5 2.475 2.525 2.425 2.575 2.6 2.574 2.626 2.522 2.678 2.7 2.673 2.727 2.619 2.781 2.8 2.772 2.828 2.716 2.884 2.9 2.871 2.929 2.813 2.987 3.0 2.970 3.030 2.910 3.090 3.1 3.069 3.131 3.007 3.193 3.2 3.168 3.232 3.104 3.296 3.3 3.267 3.333 3.201 3.399 3.4 3.366 3.434 3.298 3.502 3.5 3.465 3.535 3.395 3.605 3.6 3.564 3.636 3.492 3.708 3.7 3.663 3.737 3.589 3.811 3.8 3.762 3.838 3.686 3.914 3.9 3.861 3.939 3.783 4.017 4.0 3.960 4.040 3.880 4.120 4.1 4.059 4.141 3.977 4.223 4.2 4.158 4.242 4.074 4.326 4.3 4.257 4.343 4.171 4.429 4.4 4.356 4.444 4.268 4.532 4.5 4.455 4.545 4.365 4.635 4.6 4.554 4.646 4.462 4.738 4.7 4.653 4.747 4.559 4.841 4.8 4.752 4.848 4.656 4.944 4.9 4.851 4.949 4.753 5.047 Vdif2 TYP MAX TYP MAX 550 710 2200 2700 450 600 1900 2600 390 520 1700 2200 310 450 1500 1900 260 360 1300 1700 220 320 1100 1500 5/18 XD6216 Series ■ELECTRICAL CHARACTERISTICS (Continued) ●Voltage Chart1 (XD6216 Series) (Continued) PARAMETER NOMINAL OUTPUT VOLTAGE(V) VOUT(T) 6/18 E-0 Output Voltage (V) Output Voltage (V) Ta=25℃ -40℃≦Ta≦105℃ VOUT(E) E-1 E-2 DROPOUT VOLTAGE 1 DROPOUT VOLTAGE 2 (mV) (mV) IOUT=20mA IOUT=100mA Ta=25℃ Ta=25℃ VOUT(E) Vdif1 MIN MAX MIN MAX 5.0 4.950 5.050 4.850 5.150 5.1 5.049 5.151 4.947 5.253 5.2 5.148 5.252 5.044 5.356 5.3 5.247 5.353 5.141 5.459 5.4 5.346 5.454 5.238 5.562 5.5 5.445 5.555 5.335 5.665 5.6 5.544 5.656 5.432 5.768 5.7 5.643 5.757 5.529 5.871 5.8 5.742 5.858 5.626 5.974 5.9 5.841 5.959 5.723 6.077 6.0 5.940 6.060 5.820 6.180 6.1 6.039 6.161 5.917 6.283 6.2 6.138 6.262 6.014 6.386 6.3 6.237 6.363 6.111 6.489 6.4 6.336 6.464 6.208 6.592 6.5 6.435 6.565 6.305 6.695 6.6 6.534 6.666 6.402 6.798 6.7 6.633 6.767 6.499 6.901 6.8 6.732 6.868 6.596 7.004 6.9 6.831 6.969 6.693 7.107 7.0 6.930 7.070 6.790 7.210 7.1 7.029 7.171 6.887 7.313 7.2 7.128 7.272 6.984 7.416 7.3 7.227 7.373 7.081 7.519 7.4 7.326 7.474 7.178 7.622 7.5 7.425 7.575 7.275 7.725 7.6 7.524 7.676 7.372 7.828 7.7 7.623 7.777 7.469 7.931 7.8 7.722 7.878 7.566 8.034 7.9 7.821 7.979 7.663 8.137 8.0 7.920 8.080 7.760 8.240 Vdif2 TYP MAX TYP MAX 190 280 1000 1300 170 230 800 1150 XD6216 Series ■ELECTRICAL CHARACTERISTICS (Continued) ●Voltage Chart1 (XD6216 Series) (Continued) PARAMETER NOMINAL OUTPUT VOLTAGE(V) VOUT(T) 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 10.0 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12.0 E-0 Output Voltage (V) Output Voltage (V) Ta=25℃ VOUT(E) -40℃≦Ta≦105℃ VOUT(E) MIN MAX 7.857 8.343 7.954 8.446 8.051 8.549 8.148 8.652 8.245 8.755 8.342 8.858 8.439 8.961 8.536 9.064 8.633 9.167 8.730 9.270 8.827 9.373 8.924 9.476 9.021 9.579 9.118 9.682 9.215 9.785 9.312 9.888 9.409 9.991 9.506 10.094 9.603 10.197 9.700 10.300 9.797 10.403 9.894 10.506 9.991 10.609 10.088 10.712 10.185 10.815 10.282 10.918 10.379 11.021 10.476 11.124 10.573 11.227 10.670 11.330 10.767 11.433 10.864 11.536 10.961 11.639 11.058 11.742 11.155 11.845 11.252 11.948 11.349 12.051 11.446 12.154 11.543 12.257 11.640 12.360 MIN 8.019 8.118 8.217 8.316 8.415 8.514 8.613 8.712 8.811 8.910 9.009 9.108 9.207 9.306 9.405 9.504 9.603 9.702 9.801 9.900 9.999 10.098 10.197 10.296 10.395 10.494 10.593 10.692 10.791 10.890 10.989 11.088 11.187 11.286 11.385 11.484 11.583 11.682 11.781 11.880 MAX 8.181 8.282 8.383 8.484 8.585 8.686 8.787 8.888 8.989 9.090 9.191 9.292 9.393 9.494 9.595 9.696 9.797 9.898 9.999 10.100 10.201 10.302 10.403 10.504 10.605 10.706 10.807 10.908 11.009 11.110 11.211 11.312 11.413 11.514 11.615 11.716 11.817 11.918 12.019 12.120 E-1 E-2 DROPOUT VOLTAGE 1 DROPOUT VOLTAGE 2 (mV) (mV) IOUT=20mA IOUT=100mA Ta=25℃ Vdif1 TYP MAX Ta=25℃ Vdif2 TYP MAX 130 190 700 950 120 160 650 850 7/18 XD6216 Series ■TEST CIRCUITS ●CIRCUIT① VIN VOUT A IO UT CIN =1.0uF V CL=1.0uF CE V VSS V ●CIRCUIT② VIN A CIN =1.0uF CE A VOUT CL=1.0uF VSS ●CIRCUIT③ VOUT VIN V ～ CL=1.0uF CE VSS V ～ IOUT ●CIRCUIT④ VIN CIN =1.0uF V V 8/18 VOUT CL1.0uF CE VSS V IS HOR T XD6216 Series ■OPERATIONAL EXPLANATION The voltage divided by resistors R1 & R2 is compared with the internal voltage reference by the error amplifier. The P-channel MOSFET which is connected to the VOUT pin is then driven by the subsequent controlled signal. The output voltage at the VOUT pin is controlled and stabilized by a system of negative feedback. The current limit circuit and short protect circuit operate in relation to the level of output current and heat dissipation. Further, the IC’s internal circuitry can be shutdown via the CE pin’s signal. VIN - Erro r AMP + Curren t Limit VOUT CE ON/OFF Control VS S Voltage Reference Thermal Pro tection R1 R2 * Diodes shown in the above circuit are ESD protection diodes and parasitic diodes The XD6216 series needs an output capacitor (CL) for phase compensation. In order to ensure the stable phase compensation, please place an output capacitor (CL) of 1.0μF or bigger at the VOUT pin and VSS pin as close as possible. For a stable power input, please connect an input capacitor (CIN) of 1.0μF between the input pin (VIN) and the ground pin (VSS). Since Input capacitor (CIN), the output capacitor (CL) are bias dependence of the capacitor the influence of the missing capacity due to temperature characteristics, also there is a risk that cannot be stable phase compensation. Please pay attention to the selection of the capacitor to be used. The XD6216 series includes a current fold-back circuit as a current limit protection. When the load current reaches the current limit level, the current fold-back circuit operates and output voltage drops. The output voltage drops further and output current decreases. When the output pin is shorted, a current of about 30mA flows. The IC’s internal circuitry can be stand-by via the signal from the CE pin. In stand-by mode, output at the VOUT pin will be pulled down by R1 and R2 to the VSS level. Note that as the XD6216 series has no pull down resistor so that it will become unstable with the CE pin open. We suggest that you use this IC with either a VIN voltage or a VSS voltage input at the CE pin. If this IC is used with the correct specifications for the CE pin, the operational logic is fixed and the IC will operate normally. However, supply current may increase as a result of through current in the IC’s internal circuitry if a medium voltage is applied. The XD6216 series incorporates a thermal shutdown circuit for overheating protection. When the junction temperature of the built-in driver transistor reaches the temperature limit, the thermal shutdown circuit operates and the driver transistor will be set to OFF. The IC resumes its operation when the thermal shutdown function is released and the IC’s operation is automatically restored because the junction temperature drops to the level of the thermal shutdown release temperature. For the stable operation of the IC, over 2.0V of input voltage is necessary. The output voltage may not be generated normally if the input voltage is less than 2.0V. ■ NOTES ON USE 1． For temporary, transitional voltage drop or voltage rising phenomenon, the IC is liable to malfunction should the ratings be exceeded. 2． Where wiring impedance is high, operations may become unstable due to noise and/or phase lag depending on output current. Please strengthen VIN and VSS wiring in particular. The input capacitor (CIN) and the output capacitor (CL) should be placed to the IC as close as possible with a shorter wiring. 3． Torex places an importance on improving our products and its reliability. However, by any possibility, we would request user fail-safe design and post-aging treatment on system or equipment. 9/18 XD6216 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (1) Output Voltage vs. Output Current XD6216B331 XD6216B331 VIN=VCE=6.3V, C IN=CL=1.0uF (ceramic) 3.5 3.0 2.5 2.0 1.5 1.0 Ta=-40℃ Ta=25℃ Ta=105℃ 0.5 4.0 Output Voltage : V OUT (V) Output Voltage : V OUT (V) 4.0 50 100 150 200 250 3.5 3.0 2.5 2.0 1.5 1.0 VIN=4.3V VIN=4.3V VIN=5.3V VIN=5.3V VIN=6.3V VIN=6.3V 0.5 0.0 0.0 0 Ta=25℃,VIN=VCE , CIN=CL=1.0uF (ceramic) 0 300 4.0 3.0 2.0 Ta=-40℃ Ta=25℃ Ta=105℃ 0 50 100 150 200 250 6.0 Output Voltage : V OUT (V) Output Voltage : V OUT (V) 5.0 0.0 150 200 250 300 XD6216B501 XD6216B501 VIN=VCE=8.0V, CIN=CL=1.0uF (ceramic) 1.0 100 Output Current : IOUT (mA) Output Current : IOUT (mA) 6.0 50 Ta=25℃,VIN=VCE , CIN=CL=1.0uF (ceramic) 5.0 4.0 3.0 2.0 VIN =6.0V VIN=6V VIN =7.0V VIN=7V VIN =8.0V VIN=8V 1.0 0.0 0 300 50 100 150 200 250 Output Current : IOUT (mA) Output Current : IOUT (mA) (2) Output Voltage vs. Input Voltage XD6216B331 3.3 3.2 3.1 3 IOUT=1mA IOUT =1mA IOUT =10mA IOUT=10mA IOUT =30mA IOUT=30mA 2.9 2.8 2.8 3.3 3.8 4.3 4.8 Input Voltage : V IN (V) 10/18 5.3 Ta=25℃, V IN=V CE , CIN=CL=1.0uF(ceramic) 3.4 Output Voltage : VOUT (V) Output Voltage : V OUT (V) XD6216B331 Ta=25℃, V IN=V CE , CIN=CL=1.0uF(ceramic) 3.4 3.3 3.2 3.1 3 IOUT=1mA IOUT =1mA IOUT=10mA IOUT =10mA IOUT =30mA IOUT=30mA 2.9 2.8 4 8 12 16 20 Input Voltage : VIN (V) 24 28 XD6216 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) (2) Output Voltage vs. Input Voltage (Continued) XD6216B501 5.2 Ta=25℃, V IN=V CE , CIN=CL=1.0uF(ceramic) 5.2 Output Voltage : VOUT (V) Output Voltage : V OUT (V) XD6216B501 Ta=25℃, V IN=V CE , CIN=CL=1.0uF( ceramic) 5 4.8 4.6 4.4 IOUT=1mA IOUT=1mA IOUT=10mA IOUT=10mA IOUT=30mA IOUT=30mA 4.2 4.5 5 5.5 4.8 4.6 4.4 IOUT=1mA IOUT=1mA IOUT=10mA IOUT=10mA IOUT=30mA I =30mA 4.2 OUT 4 4 5 4 6 6 Input Voltage : V IN (V) 8 10 12 14 16 18 20 22 24 26 28 Input Voltage : VIN (V) (3) Dropout Voltage vs. Output Current XD6216B331 3.0 Ta=-40℃ Ta=25℃ Ta=105℃ 2.5 2.0 1.5 1.0 0.5 0.0 VIN=VCE, CIN=CL=1.0uF(ceramic) 3.0 Dropout Voltage : Vdif (V) Dropout Voltage : Vdif (V) XD6216B501 VIN=VCE, CIN=CL=1.0uF(ceramic) Ta=-40℃ 2.5 Ta=25℃ Ta=105℃ 2.0 1.5 1.0 0.5 0.0 0 25 50 75 100 125 150 0 25 Output Current : IOUT (mA) 50 75 100 125 150 Output Current : IOUT (mA) (4) Supply Current vs. Input Voltage 10 9 8 7 6 5 4 3 2 1 0 XC6216B331 Supply Current : ISS (uA) Supply Current : ISS (uA) XD6216B331 Ta=-40℃ Ta=25℃ Ta=105℃ 0 4 8 12 16 20 Input Voltage : V IN (V) 24 28 VIN=5.3V 10 9 8 7 6 5 4 3 2 1 0 -40 -20 0 20 40 60 80 100 120 Ambient Temprature : Ta (℃) 11/18 XD6216 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) (4) Supply Current vs. Input Voltage (Continued) XD6216B501 10 9 9 8 8 Supply Current : ISS (uA) Supply Current : ISS (uA) XD6216B501 10 7 6 5 4 3 Ta=-40℃ 2 Ta=25℃ 1 Ta=105℃ 0 0 4 8 12 16 20 24 VIN=7.0V 7 6 5 4 3 2 1 0 -40 -20 28 0 20 40 60 80 100 120 Ambient Temperature : Ta (℃) Input Voltage : V IN (V) (5) Output Voltage vs. Ambient Temperature XD6216B331 XD6216B501 CIN =CL=1.0uF(cerami 3.50 3.45 5.15 Output Voltage : VOUT (V) Output Voltage : VOUT (V) CIN =CL=1.0uF(ceramic) 5.20 3.40 3.35 3.30 3.25 3.20 1mA IOUT =1mA 10mA IOUT =10mA IOUT =20mA 20mA 3.15 3.10 -50 -25 0 25 50 75 100 Ambient Temperature : Ta (℃) 5.10 5.05 5.00 4.95 4.90 1mA IOUT =1mA 10mA IOUT =10mA IOUT =20mA 20mA 4.85 4.80 125 -50 -25 0 25 50 75 100 Ambient Temperature : Ta (℃) 125 (6) Line Transient Response XD6216B331 Input Voltage 5.0 4.0 3.6 6.0 3.5 Output Voltage 3.4 3.0 3.3 2.0 3.2 1.0 3.1 Time (1ms/div) 12/18 7.0 Input Voltage : V IN (V) Input Voltage : VIN (V) 6.0 3.7 Output Voltage : V OUT (V) 7.0 IOUT=1mA, tr=tf=5us CL=1uF(ceramic), Ta=25℃ IOUT=30mA, tr=tf=5us CL=1uF(ceramic), Ta=25℃ 3.7 3.6 Input Voltage 5.0 3.5 4.0 3.4 Output Voltage 3.0 3.3 2.0 3.2 1.0 3.1 Time (1ms/div) Output Voltage : V OUT (V) XD6216B331 XD6216 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) (6) Line Transient Response (Continued) XD6216B501 XD6216B501 9.0 5.3 8.0 Input Voltage : V IN (V) Input Voltage 7.0 5.2 6.0 5.1 Output Voltage 5.0 5.0 4.0 4.9 3.0 4.8 IOUT=30mA, tr=tf=5us CL=1uF(ceramic), Ta=25℃ 5.4 5.3 Input Voltage 7.0 Output Voltage : V OUT (V) 8.0 5.4 Input Voltage : VIN (V) 9.0 Output Voltage : VOUT (V) IOUT=1mA, tr=tf=5us CL=1uF(ceramic), Ta=25℃ 5.2 6.0 5.1 Output Voltage 5.0 5.0 4.0 4.9 3.0 4.8 Time (1ms/div) Time (1ms/div) (7) Load Transient Response XD6216B501 4 150 7 120 6 Output Voltage 3 90 2 60 30mA 1 Output Current 30 1mA 0 Output Voltage : VOUT (V) Output Vltage : VOUT (V) 5 Output Current : IOUT (mA) VIN=5.3V, tr=tf=5us CIN=CL=1.0uF(ceramic), Ta=25℃ 0 VIN=7.0V, tr=tf=5us CIN=CL=1.0uF(ceramic), Ta=25℃ 150 120 Output Voltage 5 90 4 60 3 2 Time (1us/div) 30m Output Current 30 1mA Output Current : IOUT (mA) XD6216B331 0 Time (1us/1div) (8) Input Rise Time XD6216B331 8 7 6 4 6 2 5 0 Output Voltage 4 -2 3 -4 2 -6 1 -8 0 Time(1ms/div) VIN=5.3V, tr=5us IOUT=30mA、CL=1uF(ceramic),Ta=25℃ Input Voltage 8 7 4 6 2 5 0 Output Voltage 4 -2 3 -4 2 -6 1 -8 0 Output Voltage : V OUT (V) 8 Input Voltage : V IN (V) Input Voltage : VIN (V) 6 Input Voltage XD6216B331 Output Voltage : VOUT (V) 8 VIN=5.3V, tr=5us IOUT=1mA、CL=1uF(ceramic),Ta=25℃ Time(1ms/div) 13/18 XD6216 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) (8) Input Rise Time (Continued) XD6216B501 Input Voltage 4 8 7 6 6 2 5 Output Voltage 0 4 -2 3 -4 2 -6 1 -8 0 VIN=7.0V, tr=5us IOUT=30mA、CL=1μF(ceramic),Ta=25℃ Input Voltage 4 7 6 2 0 8 5 Output Voltage 4 -2 3 -4 2 -6 1 -8 0 Time (1ms/div) Time (1ms/div) XD6216B331 XD6216B331 VIN=5.3V, tr=5us IOUT=1mA、CL=1μF(ceramic),Ta=25℃ VIN=5.3V, tr=5us IOUT=30mA、CL=1μF(ceramic),Ta=25℃ Output Voltage : VOUT (V) Input Voltage : VIN (V) 6 8 Input Voltage : V IN (V) 8 XD6216B501 Output Voltage : VOUT (V) VIN=7.0V, tr=5us IOUT=1mA、CL=1μF(ceramic),Ta=25℃ (9) CE Rise Time 7 6 2 5 0 4 -4 Output Voltage 3 2 -6 1 -8 0 6 2 5 0 4 -2 -4 -6 0 XD6216B501 VIN=7.0V, tr=5us IOUT=30mA、CL=1μF(ceramic),Ta=25℃ Output Voltage 8 8 7 6 6 5 4 -2 3 -4 2 -6 1 -8 0 Time(1ms/div) 14/18 0 Time(1ms/div) CE Input Voltage : VCE (V) 2 2 1 -8 Output Voltage : V OUT (V) CE Input Voltage : VCE (V) 4 3 Output Voltage VIN=7.0V, tr=5us IOUT=1mA、CL=1μF(ceramic),Ta=25℃ CE Input Voltage 7 6 XD6216B501 6 8 4 Time(1ms/div) 8 CE Input Voltage 4 CE Input Voltage 2 0 8 7 6 5 Output Voltage 4 -2 3 -4 2 -6 1 -8 0 Time(1ms/div) Output Voltage : V OUT (V) 4 -2 8 Output Voltage : V OUT (V) 8 CE Input Voltage : VCE (V) 6 CE Input Voltage Output Voltage : VOUT (V) CE Input Voltage : V CE (V) 8 XD6216 Series ■TYPICAL PERFORMANCE CHARACTERISTICS (Continued) (10) Ripple Rejection Rate XD6216B331 90 80 70 60 50 40 30 20 10 0 0.01 0.1 1 10 Ripple Frequency : f (kHz) Ripple Rejection Ratio : PSRR (dB) Ripple Rejection Ratio : PSRR (dB) XD6216B331 VIN=5.3.V+0.5VP-PAC, IOUT=1mA CL=1μF(ceramic),Ta=25℃ 90 80 70 60 50 40 30 20 10 0 0.01 90 80 70 60 50 40 30 20 10 0 0.01 0.1 1 Ripple Frequency : f (kHz) 10 0.1 1 10 100 Ripple Frequency : f (kHz) XD6216B501 Ripple Rejection Ratio : PSRR (dB) Ripple Rejection Ratio : PSRR (dB) XD6216B501 VIN=7.0.V+0.5VP-PAC, IOUT=1mA CL=1μF(ceramic),Ta=25℃ VIN=5.3.V+0.5VP-PAC, IOUT=30mA C L=1μF(ceramic),Ta=25℃ 90 VIN=7.0V+0.5VP-PAC, IOUT=30mA CL=1μF(ceramic),Ta=25℃ 80 70 60 50 40 30 20 10 0 0.01 0.1 1 10 Ripple Frequency : f (kHz) 15/18 XD6216 Series ■PACKAGING INFORMATION For the latest package information go to, www.torexsemi.com/technical-support/packages PACKAGE OUTLINE / LAND PATTERN THERMAL CHARACTERISTICS SOT-25 SOT-25 PKG SOT-25 Power Dissipation SOT-89-5 SOT-89-5 PKG SOT-89-5 Power Dissipation 16/18 XD6216 Series ■MARKING RULE ●SOT-25 / SOT-89-5 SOT-89-5 SOT-89-5 SOT-25(Under dot) dot仕様) SOT-25(Under 5 ⑤ ① ① ④ 4 ③ 2 ② 5 1 4 ② ③ 2 ④ ⑤ 3 Expansion 拡大 1 2 3 ① represents the product series MARK VOLTAGE (V) K M XD6216****M*-Q XD6216****P*-Q *MARK "K" is to be Under dot. ②represents the output voltage range MARK Type VOLTAGE (V) 0 1 2 3 1.8～3.0 3.1～6.0 6.1～9.0 9.1～12.0 with CE function PRODUCT SERIES XD6216B*****-Q ③ represents the output voltage VOLTAGE(V) MARK VOLTAGE(V) MARK 0 - 3.1 6.1 9.1 F - 4.6 7.6 10.6 1 - 3.2 6.2 9.2 H - 4.7 7.7 10.7 2 - 3.3 6.3 9.3 K 1.8 4.8 7.8 10.8 3 - 3.4 6.4 9.4 L 1.9 4.9 7.9 10.9 4 - 3.5 6.5 9.5 M 2.0 5.0 8.0 11.0 5 - 3.6 6.6 9.6 N 2.1 5.1 8.1 11.1 6 7 - 3.7 6.7 8.2 9.9 S 2.3 2.4 5.3 5.4 8.3 8.4 11.2 11.3 8 6.8 6.9 P R 5.2 3.8 3.9 9.7 9.8 2.2 - 9 - 4.0 7.0 10.0 T 2.5 5.5 8.5 11.5 A - 4.1 7.1 10.1 U 2.6 5.6 8.6 11.6 B - 4.2 7.2 10.2 V 2.7 5.7 8.7 11.7 C - 4.3 7.3 10.3 X 2.8 5.8 8.8 11.8 D - 4.4 7.4 10.4 Y 2.9 5.9 8.9 11.9 E - 4.5 7.5 Z 3.0 6.0 9.0 12.0 10.5 11.4 ④,⑤ represents assembly lot number 01 to 09, 0A to 0Z, 11 to 9Z, A1 to A9, AA to AZ, B1 to ZZ repeated (G, I, J, O, Q, W excluded) Note: No character inversion used. 17/18 XD6216 Series 1. 2. The product and product specifications contained herein are subject to change without notice to improve performance characteristics. Consult us, or our representatives before use, to confirm that the information in this datasheet is up to date. The information in this datasheet is intended to illustrate the operation and characteristics of our products. We neither make warranties or representations with respect to the accuracy or completeness of the information contained in this datasheet nor grant any license to any intellectual property rights of ours or any third party concerning with the information in this datasheet. 3. Applicable export control laws and regulations should be complied and the procedures required by such laws and regulations should also be followed, when the product or any information contained in this datasheet is exported. 4. The product is neither intended nor warranted for use in equipment of systems which require extremely high levels of quality and/or reliability and/or a malfunction or failure which may cause loss of human life, bodily injury, serious property damage including but not limited to devices or equipment used in 1) nuclear facilities, 2) aerospace industry, 3) medical facilities, 4) automobile industry and other transportation industry and 5) safety devices and safety equipment to control combustions and explosions, excluding when specified for in-vehicle use or other uses. Do not use the product for in-vehicle use or other uses unless agreed by us in writing in advance. 5. Although we make continuous efforts to improve the quality and reliability of our products; nevertheless Semiconductors are likely to fail with a certain probability. So in order to prevent personal injury and/or property damage resulting from such failure, customers are required to incorporate adequate safety measures in their designs, such as system fail safes, redundancy and fire prevention features. 6. Our products are not designed to be Radiation-resistant. 7. Please use the product listed in this datasheet within the specified ranges. 8. We assume no responsibility for damage or loss due to abnormal use. 9. All rights reserved. No part of this datasheet may be copied or reproduced unless agreed by Torex Semiconductor Ltd in writing in advance. TOREX SEMICONDUCTOR LTD. 18/18