2SD1160

2SD1160 TOSHIBA Transistor Silicon NPN Epitaxial Type (PCT Process) 2SD1160 Switching Applications Suitable for Motor Drive Applications • • • High DC current gain Low saturation voltage: VCE (sat) = 0.6 V (max) (IC = 2A, IB = 40 mA) Built-in free wheel diode Unit: mm Absolute Maximum Ratings (Ta = 25°C) Characteristics Collector-base voltage Collector-emitter voltage Emitter-base voltage Collector current DC Pulse Symbol VCBO VCEO VEBO IC ICP IFP PC Tj Tstg Rating 50 20 6 2 4 1 1 10 150 −55 to 150 Unit V V V A A W °C °C Diode forward surge current (t = 1 s) Collector power dissipation Junction temperature Storage temperature range Ta = 25°C Tc = 25°C JEDEC JEITA ― ― TOSHIBA 2-7B1A Note: Using continuously under heavy loads (e.g. the application of high Weight: 0.36 g (typ.) temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Equivalent Circuit COLLECTOR BASE ≈ 800 Ω EMITTER 1 2006-11-21 2SD1160 Electrical Characteristics (Ta = 25°C) Characteristics Collector cut-off current Emitter cut-off current Collector-emitter sustaining voltage Symbol ICBO IEBO VCEO (SUS) hFE (1) DC current gain (Note) hFE (2) Collector emitter saturation voltage Base-emitter saturation voltage Emitter-collector forward voltage VCE (sat) VBE (sat) VECF Test Condition VCB = 50 V, IE = 0 VEB = 5 V, IC = 0 IC = 20 mA, L = 40 mH VCE = 2 V, IC = 1 A VCE = 2 V, IC = 2 A IC = 2 A, IB = 40 mA IC = 2 A, IB = 40 mA IE = 1 A , I B = 0 Min ― 2.5 20 100 60 ― ― ― Typ. ― 6.25 ― ― ― 0.4 ― ― Max 1 15 ― 300 ― 0.6 1.5 2.0 V V V Unit μA mA V Note: hFE (1) classification O: 100 to 200, Y: 150 to 300 Classification 2SD1160-O 2SD1160-Y Min 100 150 Max 200 300 Marking D1160 Part No. (or abbreviation code) Lot No. Characteristics indicator A line indicates lead (Pb)-free package or lead (Pb)-free finish. 2 2006-11-21 2SD1160 IC – VCE 1.0 8 10 0.8 6 0.6 5 4 0.4 3 IB = 2 mA 0 0 0 2 4 6 8 10 12 14 10 10 30 100 Common emitter Tc = 25°C 1000 hFE – IC Common emitter 500 VCE = 2 V Tc = 100°C 25 100 −25 50 30 Collector current IC 0.2 DC current gain hFE (A) 300 300 1000 3000 Collector current IC (mA) Collector-emitter voltage VCE (V) VCE (sat) – IC Collector-emitter saturation voltage VCE (sat) (V) 1 Common emitter 10 VBE (sat) – IC Common emitter Base-emitter saturation voltage VBE (sat) (V) 0.5 0.3 IC/IB = 50 Tc = −25°C 25 100 5 3 IC/IB = 50 0.1 1 Tc = −25°C 0.05 0.03 30 0.5 25 100 100 300 1000 3000 Collector current IC (mA) 0.2 30 100 300 1000 3000 Collector current IC (mA) IE – VECF 1000 500 IB = 0 rth – tw Transient thermal resistance rth (°C/W) Curves apply only to limited areas of thermal resistance. (Single nonrepetitive pulse) Tc = 25°C IE (mA) 1000 300 Tc = 100°C 25 −25 100 Emitter current 100 50 30 10 1 10 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.1 1m 10 m 100 m 1 10 100 1000 Emitter-collector forward voltage VECF (V) Pulse width tw (s) 3 2006-11-21 2SD1160 Safe Operating Area Operating conditions used for a 1 test circuit shown in Figure 1 must not exceed this shaded area. 0.5 Tc = 25°C 10 V L = 10 mH 3 ms INPUT 2 ms T.U.T 330 Ω VCC Collector current IC (A) Figure 1 0.01 0 0 10 20 30 40 50 60 70 Safe Operating Area Test Circuit Collector-emitter voltage VCE (V) PC – Ta 1.2 PC (W) Collector power dissipation 1.0 0.8 0.6 0.4 0.2 0 0 20 40 60 80 100 120 140 160 Ambient temperature Ta (°C) 4 2006-11-21 2SD1160 RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 5 2006-11-21