74VHCT08AFT

TC74VHCT08AF/AFN/AFT/AFK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74VHCT08AF,TC74VHCT08AFN,TC74VHCT08AFT,TC74VHCT08AFK Quad 2-Input AND Gate The TC74VHCT08A is an advanced high speed CMOS 2-INPUT AND GATE fabricated with silicon gate C2MOS technology. It achieves the high speed operation similar to equivalent Bipolar Schottky TTL while maintaining the CMOS low power dissipation. The input voltage are compatible with TTL output voltage. This device may be used as a level converter for interfacing 3.3 V to 5 V system. Input protection and output circuit ensure that 0 to 5.5 V can be applied to the input and output (Note) pins without regard to the supply voltage. These structure prevents device destruction due to mismatched supply and input/output voltages such as battery back up, hot board insertion, etc. Note: Note: xxxFN (JEDEC SOP) is not available in Japan. TC74VHCT08AF VCC = 0 V Features • High speed: tpd = 5.0 ns (typ.) at VCC = 5 V • Low power dissipation: ICC = 2 μA (max) at Ta = 25°C • Compatible with TTL outputs: VIL = 0.8 V (max) VIH = 2.0 V (min) • TC74VHCT08AFN • Power down protection is provided on all inputs and outputs. ∼ tpHL Balanced propagation delays: tpLH − • Low noise: VOLP = 0.8 V (max) • Pin and function compatible with the 74 series (74AC/HC/F/ALS/LS etc.) 08 type. TC74VHCT08AFT TC74VHCT08AFK Weight SOP14-P-300-1.27A SOP14-P-300-1.27 SOL14-P-150-1.27 TSSOP14-P-0044-0.65A VSSOP14-P-0030-0.50 : 0.18 g (typ.) : 0.18 g (typ.) : 0.12 g (typ.) : 0.06 g (typ.) : 0.02 g (typ.) 1 2006-06-01 TC74VHCT08AF/AFN/AFT/AFK Pin Assignment IEC Logic Symbol 1A 1 14 VCC 1B 2 13 4B 1Y 3 12 4A 2A 11 4 1A 1B 2A 2B 3A 3B 4Y 2B 5 10 3B 2Y 6 9 3A GND 7 8 3Y 4A 4B (1) (2) & (3) (4) 1Y (6) (5) (9) 2Y (8) (10) (12) 3Y (11) (13) 4Y (top view) Truth Table A B Y L L L L H L H L L H H H Absolute Maximum Ratings (Note 1) Characteristics Symbol Rating Unit Supply voltage range VCC −0.5 to 7.0 V DC input voltage VIN −0.5 to 7.0 V −0.5 to 7.0 (Note 2) −0.5 to VCC + 0.5 (Note 3) DC output voltage VOUT Input diode current IIK −20 Output diode current IOK ±20 DC output current IOUT ±25 mA DC VCC/ground current ICC ±50 mA Power dissipation PD 180 mW Storage temperature Tstg −65 to 150 °C V mA (Note 4) mA Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Note 2: VCC = 0 V Note 3: High or low state. IOUT absolute maximum rating must be observed. Note 4: VOUT < GND, VOUT > VCC 2 2006-06-01 TC74VHCT08AF/AFN/AFT/AFK Recommended Operating Conditions (Note 1) Characteristics Symbol Rating Unit Supply voltage VCC 4.5 to 5.5 V Input voltage VIN 0 to 5.5 V Output voltage VOUT 0 to 5.5 (Note 2) 0 to VCC (Note 3) V Operating temperature Topr −40 to 85 °C Input rise and fall time dt/dV 0 to 20 ns/V Note 1: The recommended operating conditions are required to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Note 2: VCC = 0 V Note 3: High or low state. Electrical Characteristics DC Characteristics Characteristics Symbol Ta = −40 to 85°C Ta = 25°C Test Condition VCC (V) Min Typ. Max Min Max Unit High-level input voltage VIH ⎯ 4.5 to 5.5 2.0 ⎯ ⎯ 2.0 ⎯ V Low-level input voltage VIL ⎯ 4.5 to 5.5 ⎯ ⎯ 0.8 ⎯ 0.8 V High-level output voltage VOH IOH = −50 μA VIN = VIH or VIL I OH = −8 mA 4.5 4.40 4.50 ⎯ 4.40 ⎯ 4.5 3.94 ⎯ ⎯ 3.80 ⎯ Low-level output voltage VOL IOL = 50 μA VIN = VIH or VIL I = 8 mA OL 4.5 ⎯ 0.0 0.1 ⎯ 0.1 4.5 ⎯ ⎯ 0.36 ⎯ 0.44 VIN = 5.5 V or GND 0 to 5.5 ⎯ ⎯ ±0.1 ⎯ ±1.0 μA ICC VIN = VCC or GND 5.5 ⎯ ⎯ 2.0 ⎯ 20.0 μA ICCT Per input: VIN = 3.4 V Other input: VCC or GND 5.5 ⎯ ⎯ 1.35 ⎯ 1.50 mA IOPD VOUT = 5.5 V 0 ⎯ ⎯ 0.5 ⎯ 5.0 μA Input leakage current Quiescent supply current Output leakage current IIN 3 V V 2006-06-01 TC74VHCT08AF/AFN/AFT/AFK AC Characteristics (input: tr = tf = 3 ns) Characteristics VCC (V) Propagation delay time tpLH Input capacitance CIN Power dissipation capacitance CPD Note: tpHL ⎯ Ta = −40 to 85°C Ta = 25°C Test Condition Symbol Unit CL (pF) Min Typ. Max Min Max 15 ⎯ 5.0 6.9 1.0 8.0 50 ⎯ 5.5 7.9 1.0 9.0 ⎯ 4 10 ⎯ 10 pF ⎯ 18 ⎯ ⎯ ⎯ pF 5.0 ± 0.5 ⎯ (Note) ns CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD·VCC·fIN + ICC/4 (per gate) Noise Characteristics (input: tr = tf = 3 ns) Characteristics Ta = 25°C Test Condition Symbol VCC (V) Typ. Max Unit Quiet output maximum dynamic VOL VOLP CL = 50 pF 5.0 0.4 0.8 V Quiet output minimum dynamic VOL VOLV CL = 50 pF 5.0 −0.4 −0.8 V Minimum high level dynamic input voltage VIHD CL = 50 pF 5.0 ⎯ 2.0 V Maximum low level dynamic input voltage VILD CL = 50 pF 5.0 ⎯ 0.8 V 4 2006-06-01 TC74VHCT08AF/AFN/AFT/AFK Package Dimensions Weight: 0.18 g (typ.) 5 2006-06-01 TC74VHCT08AF/AFN/AFT/AFK Package Dimensions Weight: 0.18 g (typ.) 6 2006-06-01 TC74VHCT08AF/AFN/AFT/AFK Package Dimensions (Note) Note: This package is not available in Japan. Weight: 0.12 g (typ.) 7 2006-06-01 TC74VHCT08AF/AFN/AFT/AFK Package Dimensions Weight: 0.06 g (typ.) 8 2006-06-01 TC74VHCT08AF/AFN/AFT/AFK Package Dimensions Weight: 0.02 g (typ.) 9 2006-06-01 TC74VHCT08AF/AFN/AFT/AFK Note: Lead (Pb)-Free Packages SOP14-P-300-1.27A SOL14-P-150-1.27 TSSOP14-P-0044-0.65A RESTRICTIONS ON PRODUCT USE VSSOP14-P-0030-0.50 20070701-EN • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 10 2006-06-01