CRG03

CRG03 TOSHIBA Rectifier Silicon Diffused Type CRG03 General Purpose Rectifier Applications • • • Average forward current: IF (AV) = 1.0 A Repetitive peak reverse voltage: VRRM = 400 V Suitable for compact assembly due to small surface-mount package “S−FLATTM” (Toshiba package name) Unit: mm Absolute Maximum Ratings (Ta = 25°C) Characteristics Repetitive Peak Reverse Voltage Average Forward Current Peak One Cycle Surge Forward Current (Non−Repetitive) Junction Temperature Storage Temperature Range Symbol VRRM IF (AV) IFSM 16.5 (60Hz) Tj Tstg −40~150 −40~150 °C °C Rating 400 1.0（Note） 15.0 (50Hz) A Unit V A Note: 1 Ta = 56°C Device mounted on a ceramic board board size: 50 mm × 50 mm soldering land: 2 mm × 2 mm board thickness 0.64t JEDEC JEITA TOSHIBA ― ― 3-2A1A Weight: 0.013 g (typ.) Note 2: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Electrical Characteristics (Ta = 25°C) Characteristics Symbol VFM(1) Peak forward voltage VFM(2) VFM(3) Repetitive peak reverse current IRRM Test Condition IFM = 0.1 A (Pulse test) IFM = 0.7 A (Pulse test) IFM = 1.0 A (Pulse test) VRRM = 400 V (Pulse test) Device mounted on a ceramic board Board size: 50 mm × 50 mm Soldering land: 2 mm × 2 mm Board thickness: 0.64t Thermal resistance Rth (j-a) Device mounted on a glass-epoxy board Board size: 50 mm × 50 mm Soldering land: 6 mm × 6 mm Board thickness: 1.6t ― Min ⎯ ⎯ ⎯ ⎯ ⎯ Typ. 0.86 0.97 1.0 ⎯ ⎯ Max ⎯ 1.1 ⎯ 10 Unit V V V μA 65 °C/W ⎯ ⎯ 130 Rth (j-ℓ) ⎯ ⎯ 20 °C/W 1 2006-11-06 CRG03 Marking Abbreviation Code G3 Part No. CRG03 Standard Soldering Pad Unit: mm 1.2 1.2 2.8 Handling Precaution The absolute maximum ratings denote the absolute maximum ratings, which are rated values and must not be exceeded during operation, even for an instant. The following are the general derating methods that we recommend when you design a circuit with a device. VRRM: We recommend that the worst case voltage, including surge voltage, be no greater than 80% of the absolute maximum rating of VRRM for a DC circuit and be no greater than 50% of that of VRRM for an AC circuit. VRRM has a temperature coefficient of 0.1%/℃. Take this temperature coefficient into account designing a device at low temperature. IF(AV): We recommend that the worst case current be no greater than 80% of the absolute maximum rating of IF(AV). Carry out adequate heat design. If you can’t design a circuit with excellent heat radiation, set the margin by using an allowable Tamax-IF (AV) curve. This rating specifies the non-repetitive peak current in one cycle of a 50-Hz sine wave, condition angle 180. Therefore, this is only applied for an abnormal operation, which seldom occurs during the lifespan of the device. We recommend that a device be used at a Tj of below 120℃ under the worst load and heat radiation conditions. Thermal resistance between junction and ambient fluctuates depending on the device’s mounting condition. When using a device, design a circuit board and a soldering land size to match the appropriate thermal resistance value. Please refer to the Rectifiers databook for further information. 2 2006-11-06 CRG03 iF – vF 10 1.4 Pulse test PF (AV) – IF (AV) Halfsine waveform iF (A) Instantaneous forward current Tj = 150°C Average forward power dissipation PF (AV) (W) 1.2 1.0 0.8 0.6 0° 180° Conduction angle 180° 1 75°C 25°C 0.4 0.2 0.0 0.0 0.1 0.4 0.8 1.2 1.6 2.0 2.4 2.8 0.2 0.4 0.6 0.8 1.0 1.2 Instantaneous forward voltage vF (V) Average forward current IF (AV) (A) Ta max – IF (AV) 160 140 Device mounted on Device mounted on a ceramic board a glass-epoxy board Device mounted on a ceramic board Maximum allowable temperature Ta max (°C) Soldering land Board size Board thickness 2 mm □ □ 6 mm □ □ 120 100 80 glass-epoxy board 60 40 20 0 0 0° 180° Device mounted on a 50 mm 0.64 t 50 mm 1.6 t Halfsine waveform Conduction angle 180° 0.2 0.4 0.6 0.8 1.0 1.2 Average forward current IF (AV) (A) Surge forward current (non-repetitive) 30 10000 rth (j-a) – t Transient thermal impedance rth (j-a) (°C/W) Ta = 25°C f = 50 Hz (1) Device mounted on a ceramic board: Soldering land: 2 mm × 2 mm 1000 (2) Device mounted on a glass-epoxy board: Soldering land: 6 mm × 6 mm IFSM (A) Peak surge forward current 25 20 15 100 (2) (1) 10 10 5 0 1 10 100 1 0.001 0.01 0.1 1 10 100 Number of cycles Time t (s) 3 2006-11-06 CRG03 RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 4 2006-11-06