TA1218ANG

TA1218ANG TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic TA1218ANG Audio/Video Switching IC for TVs The TA1218ANG is an audio/video switching IC for TV sets. Conforming to I2C bus standards, it allows you to perform various switching operations through the bus lines by using a microcomputer. Thanks to its 2-channel outputs, the TA1218ANG can also be used for the PIP systems. Furthermore, since the presence of a signal on its sync signal output pin can be determined by a microcomputer, it is possible to check each input/output channel (self-diagnosis). This IC has the same pin assignments as the TA1219ANG (SDIP36), a 1-channel output version of the TA1218ANG, so these chips are pin compatible on pins 3 to 20 and 23 to 40. TA1218ANG SDIP42-P-600-1.78 Weight: 4.13 g (typ.) Features • • • • • • • I2C bus control Video : 5-channel inputs and 2-channel outputs (2 channels conforming to S system) Audio : 5-channel inputs and 3-channel outputs Self-diagnostic function ADC inputs based on European 21-pin standards ADC inputs based on S1/S2 terminal standards Switchable subaddress 1 2005-11-15 TA1218ANG Block Diagram Det Select Det in VCC GND −6dB VinV1 VinV2 VinTV 10 28 7 12 16 38 Vout1 4 3 33 23 VCC GND Y/VinS1 Y/VinS2 ) 42 36 + S + 34 32 S Mute Sync separator IC bus Pulse converter 2 Vout2 Yout Yin 30 CinS1 CinS2 14 18 Cout Cin 24 25 27 19 SCL SDA Address I/O1 (4 level) I/O2 (4 level) I/O3 O4 O5 LoutTV Lout1 Lout2 Sync out 26 IL Logic 2 20 I/O 21 22 41 40 37 1 LinS1 LinS2 LinV1 LinV2 LinTV 11 15 8 29 5 RinS1 RinS2 RinV1 RinV2 RinTV 13 17 9 31 6 39 35 2 RoutTV Rout1 Rout2 2 2005-11-15 TA1218ANG Pin Assignment TA1218ANG 1 Lout2 2 Rout2 3 Det in 4 Det Select 5 LinTV 6 RinTV 7 VinTV 8 LinV1 9 RinV1 10 VinV1 11 11 LinS1 12 Y/VinS1 13 RinS1 14 CinS1 15 LinS2 16 Y/VinS2 17 RinS2 18 CinS2 19 I/O1 20 I/O2 21 I/O3 TA1218ANG Vout2 42 O5 41 LoutTV 40 RoutTV 39 Vout1 38 Lout1 37 Yout 36 Rout1 35 Cout 34 VCC 33 Cin 32 RinV2 31 Yin 30 LinV2 29 VinV2 28 Address 27 Sync out 26 SDA 25 SCL GND 23 O4 22 3 2005-11-15 TA1218ANG Pin Description Pin No. Name Function This pin is for output a sub-channel left audio signal. The signals fed into the chip via LinV1, LinV2, LinS1, LinS2, or LinTV is output from this pin. The output resistance of this pin is 45 Ω. Lout2 Furthermore, the signal output from this pin is pulse-converted for use in self-diagnosis. The converted signal is output from Sync Out. This output can be muted in combination with Rout2 by bus control. This pin is for output a sub-channel right audio signal. The signals fed into the chip via RinV1, RinV2, RinS1, RinS2, or RinTV is output from this pin. The output resistance of this pin is 45 Ω. Rout2 Furthermore, the signal output from this pin is pulse-converted for use in self-diagnosis. The converted signal is output from Sync Out. This output can be muted in combination with Lout2 by bus control. Interface 100 Ω 1 1 20 kΩ 1.5 mA 100 Ω 70 kΩ 20 kΩ 1.5 mA 70 kΩ Lout2 SW 2 Rout2 SW 2 3 Det in This pin is for input a sync separation signal. Input the signal from Det Select to this pin with capacitance coupling. The input resistance of this pin is 18 kΩ. The sync signal separated from Det Select is outputted from Sync Out for use in self-diagnosis. 3 7 µA/1.1 µA 1 kΩ 7.3 V 22.5 kΩ This pin is for output a sync separation signal. 4 Signals VinV1, VinV2, VinTV, Y/VinS1, Vout1, Vout2, Yout, or Cout are outputted from this pin. The output resistance of this pin is 35 Ω. Input the signal from this pin to Det in with capacitance coupling. 100 Ω Det Select SW Det Select 4 200 Ω 1 kΩ 4 2005-11-15 TA1218ANG Pin No. Name Function Interface 5 LinTV The input dynamic range of this pin is 6.5 Vp-p and the input resistance is 70 kΩ. 5.2 V 70 kΩ This pin is for input a left audio signal from the main demodulator in the TV set. The signal fed into this pin is presented to LoutTV, Lout1, and Lout2. 1.5 kΩ 5 1.5 kΩ 1.5 kΩ 6 RinTV The input dynamic range of this pin is 6.5 Vp-p and the input resistance is 70 kΩ. 5.2 V 70 kΩ This pin is for input a right audio signal from the main demodulator in the TV set. The signal fed into this pin is presented to RoutTV, Rout1, and Rout2. 1.5 kΩ 6 1.5 kΩ 1.5 kΩ 7 VinTV The input dynamic range of this pin is 2.0 Vp-p and the input resistance is 30 kΩ. 5.2 V 30 kΩ This pin is for input a composite audio signal from the main demodulator in the TV set. The signal fed into this pin is presented to Vout1, Vout2, Yout, and Cout. The same signal is also output from Det Select as a sync separation signal. 1.5 kΩ 7 1.5 kΩ 1.5 kΩ 8 LinV1 The input dynamic range of this pin is 6.5 Vp-p and the input resistance is 70 Ω. 5.2 V 70 kΩ This pin is for input a left audio signal from an external source (V1 channel). This pin can also be used for PIP signal input. The signal fed into this pin is presented to Lout1 and Lout2. 1.5 kΩ 8 1.5 kΩ 5 2005-11-15 TA1218ANG Pin No. Name Function Interface 9 RinV1 The input dynamic range of this pin is 6.5 Vp-p and the input resistance is 70 kΩ. 5.2 V 70 kΩ This pin is for input a right audio signal from an external source (V1 channel). This pin can also be used for PIP signal input. The signal fed into this pin is presented to Rout1 and Rout2. 1.5 kΩ 9 1.5 kΩ 10 VinV1 5.2 V 30 kΩ This pin is for input a composite video signal from an external source (V1 channel). This pin can also be used for PIP signal input. The signal fed into this pin is presented to Vout1, Vout2, Yout, and Cout. The same signal is also output from Det Select as a sync separation signal. The input dynamic range of this pin is 2.0 Vp-p and the input resistance is 30 kΩ. 1.5 kΩ 10 1.5 kΩ 1.5 kΩ 11 LinS1 This pin is for input a left audio signal from an external source (S1 channel). The signal fed into this pin is presented to Lout1 and Lout2. The input dynamic range of this pin is 6.5 Vp-p and the input resistance is 70 kΩ. 1.5 kΩ 11 5.2 V 70 kΩ 1.5 kΩ 12 Y/VinS1 5.2 V 30 kΩ This pin is for input a luminance signal or composite video signal from an external source (S1 channel). The signal fed into this pin is presented to Vout1, Vout2, Yout, and Cout. The same signal is also output from Det Select as a sync separation signal. The input dynamic range of this pin is 2.0 Vp-p and the input resistance is 30 kΩ. 1.5 kΩ 12 1.5 kΩ 1.5 kΩ 6 2005-11-15 TA1218ANG Pin No. Name Function Interface 13 RinS1 This pin is for input a right audio signal from an external source (S1 channel). The signal fed into this pin is presented to Rout1 and Rout2. The input dynamic range of this pin is 6.5 Vp-p and the input resistance is 70 kΩ. 1.5 kΩ 13 5.2 V 70 kΩ 1.5 kΩ 14 CinS1 5.2 V 30 kΩ This pin is for input a chroma signal from an external source (S1 channel). It also functions as an S-mode select switch for the S1 channel. The S mode is selected when the pin voltage is 2.25 V or less. The signal fed into this pin is presented to Cout directly and to Vout1 and Vout2 after being combined with the YinS1 signal. The input dynamic range of this pin is 2.0 Vp-p and the input resistance is 30 kΩ. 1.5 kΩ 1.5 kΩ 1.5 kΩ S Mode SW 2.25 V 14 15 LinS2 This pin is for input a left audio signal from an external source (S2 channel). The signal fed into this pin is presented to Lout1 and Lout2. The input dynamic range of this pin is 6.5 Vp-p and the input resistance is 70 kΩ. 1.5 kΩ 15 5.2 V 70 kΩ 1.5 kΩ 16 Y/VinS2 The input dynamic range of this pin is 2.0 Vp-p and the input resistance is 30 kΩ. 5.2 V 30 kΩ This pin is for input a luminance signal or composite aoudio signal from an external source (S2 channel). The signal fed into this pin is presented to Vout1, Vout2, Yout, and Cout. 1.5 kΩ 16 1.5 kΩ 7 2005-11-15 TA1218ANG Pin No. Name Function Interface 17 RinS2 This pin is for input a right audio signal from an external source (S2 channel). The signal fed into this pin is presented to Rout1 and Rout2. The input dynamic range of this pin is 6.5 Vp-p and the input resistance is 70 kΩ. 1.5 kΩ 17 5.2 V 70 kΩ 1.5 kΩ 18 CinS2 5.2 V 30 kΩ This pin is for input a chroma signal from an external source (S2 channel). It also functions as an S-mode select switch for the S2 channel. The S mode is selected when the pin voltage is 2.25 V or less. The signal fed into this pin is presented to Cout directly and to Vout1 and Vout2 after being combined with the YinS2 signal. The input dynamic range of this pin is 2.0 Vp-p and the input resistance is 30 kΩ. 1.5 kΩ 1.5 kΩ 1.5 kΩ S Mode SW 2.25 V 8.0 V 8.0 V 18 This is an ADC input/DAC output pin. 19 The ADC is a 4-level detection type (2 bits). The threshold levels are 8.0 V , 3.0 V and 0.75V. The DAC (1 bit) is an open-collector output. Make sure that the current flowing into this pin is 2.0 mA or less. Logic This is an ADC input/DAC output pin. 20 The ADC is a 4-level detection type (2 bits). The threshold levels are 8.0 V, 3.0V and 0.75V. The DAC (1 bit) is an open-collector output. Make sure that the current flowing into this pin is 2.0 mA or less. Logic 3.0V I/O2 20 3.0 V I/O1 19 8 2005-11-15 TA1218ANG Pin No. Name Function Interface This is an ADC input/DAC output pin. 21 I/O3 The ADC is a 2-level detection type (1 bit). The threshold level is 2.25 V. The DAC (1 bit) is an open-collector output. Make sure that the current flowing into this pin is 2.0 mA or less. Logic 22 O4 This pin is for a 1 bit DAC output. This is an open-collector output. Make sure that the current flowing into this pin is 2.0 mA or less. 22 Logic 23 GND This is the GND pin. ⎯ 24 SCL This pin is for input an I C bus clock. The input threshold level of this pin 24 is 2.25 V. Surge protection circuit 2.25 V 2.25 V 2 2.25 V 21 Logic 25 SDA This is an I C bus data input/output pin. The input threshold level of this pin is 2.25 V. Make sure that the current flowing into this pin is 3.0 mA or less. 2 25 Surge protection circuit Logic 9 2005-11-15 TA1218ANG Pin No. Name Function Interface 26 Sync out This pin is for output a self-diagnostic sync signal. The signal separated from VinTV VinV1, VinV2, Y/VinS1, Vout1, Vout2, Yout, or Cout is outputted from this pin. In addition, the signal derived from Lout1, Rout1, Lout2, or Rout2 is also output from this pin for use in audio block diagnosis. This is an open-collector output. Make sure that the current flowing into this pin is 2.0 mA or less. Output select SW 26 27 Address This is for an I C bus slave address select switch. The threshold level of this pin is 2.25 V. The following lists the addresses : High : 92H (write), 93H (read) Low : 90H (write), 91H (read) 2 Address select SW 60 kΩ 27 30 kΩ 28 VinV2 5.2 V 30 kΩ This pin is for input a composite video signal from an external source (V2 channel). This pin can also be used for PIP signal input. The signal fed into this pin is presented to Vout1, Vout2, Yout, and Cout. The same signal is also output from Det Select as a sync separation signal. The input dynamic range of this pin is 2.0 Vp-p and the input resistance is 30 kΩ. 1.5 kΩ 28 1.5 kΩ 1.5 kΩ 29 LinV2 The input dynamic range of this pin is 6.5 Vp-p and the input resistance is 70 kΩ. 5.2 V 70 kΩ This pin is for input a left audio signal from an external source (V2 channel). This pin can also be used for PIP signal input. The signal fed into this pin is presented to Lout1 and Lout2. 1.5 kΩ 29 1.5 kΩ 1.5 V 10 2005-11-15 TA1218ANG Pin No. Name Function Interface 30 Yin This pin is for input a luminance signal from an external comb filter. The signal fed into this pin is presented to Yout. The input dynamic range of this pin is 5.5 Vp-p and the input resistance is 60 kΩ. 1.5 kΩ 30 5.2 V 60 kΩ 31 RinV2 The input dynamic range of this pin is 6.5 Vp-p and the input resistance is 70 kΩ. 5.2 V 70 kΩ This pin is for input a right audio signal from an external source (V2 channel). This pin can also be used for PIP signal input. The signal fed into this pin is presented to Rout1 and Rout2. 1.5 kΩ 31 1.5 kΩ This pin is for input a chroma signal from an external comb filter. The signal fed into this pin is presented to Cout. 32 Cin The input dynamic range of this pin is 5.5 Vp-p and the input resistance is 60 kΩ. This pin also functions as a audio mute switch. The entire audio output can be muted by pulling the voltage on this pin below 2.25 V. This is the power supply pin. Apply 9 V to this pin. The current consumption of this pin is 47 mA. 1.5 kΩ 5.2 V 60 kΩ 1.5 kΩ Sound Mute 2.25 V 32 33 VCC ⎯ 34 Cout This pin is for output a chroma signal. The signal fed into Cin, CinS1, CinS2, VinV1, VinV2, Y/VinS1, Y/VinS2, or VinTV is outputted from this pin. The output resistance of this pin is 25 Ω. The same signal is also outputted from Det Select as a sync separation signal. 100 Ω Cout SW 34 1.8 mA 1.5 kΩ 11 2005-11-15 TA1218ANG Pin No. Name Function This pin is for output the main channel right audio signal. The signal fed into RinV1, RinV2, RinS1, RinS2, or RinTV is outputted from this pin. The output resistance of this pin is 45 Ω. Rout1 Furthermore, the signal outputted from this pin is pulse-converted for use in self-diagnosis. The converted signal is outputted from Sync Out. This outputted can be muted independently of Lout1 by bus control. Interface 100 Ω 35 35 20 kΩ 1.5 mA 36 Yout This pin is for output a luminance signal. The signal fed into Yin, Y/VinS1, Y/VinS2, VinV1, VinV2, or VinTV is outputted from this pin. The output resistance of this pin is 25 Ω. The same signal is also outputted from Det Select as a sync separation signal. 100 Ω Yout SW 36 1.8 mA 70 kΩ Rout1 SW 1.5 kΩ 37 Lout1 20 kΩ This output can be muted independently of Rout1 by bus control. 38 Vout1 2.0 mA This pin is for output the main channel composite video signal. The signal fed into VinTV, VinV1, VinV2, VinS1, VinS2, YinS1 + CinS1, or YinS2 + CinS2 is outputted from this pin. The output resistance of this pin is 25 Ω The same signal is also outputted from Det Select as a sync separation signal. 100 Ω Vout1 SW 38 1.5 mA Furthermore, the signal outputted from this pin is pulse-converted for use in self-diagnosis. The converted signal is outputted from Sync Out. 37 70 kΩ This pin is for output the main channel left audio signal. The signal fed into LinV1, LinV2, LinS1, LinS2, or LinTV is outputted from this pin. The output resistance of this pin is 45 Ω. 100 Ω Lout1 SW 1.5 kΩ 12 2005-11-15 TA1218ANG Pin No. Name Function Interface 100 Ω 39 RoutTV 20 kΩ 100 Ω 1.5 mA This output can be muted in combination with LoutTV by bus control. 39 70 kΩ 20 kΩ 100 Ω Vout2 SW 1.5 mA Logic 70 kΩ 2.0 mA This pin is for output only the signal that is forwarded from RinTV. The output resistance of this pin is 45 Ω. RoutTV SW 40 LoutTV This pin is for output only the signal that is forwarded from LinTV. The output resistance of this pin is 45 Ω. This output can be muted in combination with RoutTV by bus control. LoutTV SW 40 41 O5 This is a 1 bit DAC output pin. This is an open-collector output. Make sure that the current flowing into this pin is 2.0 mA or less. 41 42 Vout2 This pin is for output a sub-channel composite video signal. The signal fed into VinTV, VinV1, VinV2, VinS1, VinS2, YinS1 + CinS1, or YinS2 + CinS2 is outputted from this pin. The output resistance of this pin is 25 Ω. The same signal is also outputted from Det Select as a sync separation signal. 42 1.5 kΩ 13 2005-11-15 TA1218ANG Bus Data Specifications Data Structure (1) Write Slave address (90H or 92H) W (0) S A Data 1 A Data 2 A Data 3 A P (2) Read Slave address (91H or 93H) R (1) S A Data 4 A P Note2: Slave address is switched by the voltage applied to pin 27 (address). Switched to 90H when low (GND); switched to 92H when high (VCC) during write mode. Contents of Data Mode Data No. B07 Data 1 [F0H] LoutTV RoutTV B17 Write Data 2 [1FH] Sync detection sensitivity switching B27 Data 3 [07H] O5 B37 Read Data 4 I/O3 O4 B36 DAC output switching Input select (sub) I/O3 B35 I/O2 B34 I/O1 B33 B32 B31 B30 Power-on reset B06 B05 Contents of Data B04 B03 Forced TV Audio B13 B12 B02 B01 B00 Audio mute Lout2 Rout2 B16 Sync output switching B26 Rout1 B15 Lout1 B14 YC output switching Yout B11 Cout B10 Sync (diagnosis) detection switching Input select (main) B25 B24 B23 B22 B21 B20 ADC input discrimination I/O2 Hi I/O2 Low I/O1 Hi I/O1 Low S input discrimination CinS1 CinS2 Note3: Shown in [ ] are reset data. Note4: The data contents marked by a slash (/) are an unused bit (data free). 14 2005-11-15 TA1218ANG Main Video Select: Terminal 38 Output Signal Mode Input S/V V S1 S FV V S2 S FV (Note5) V1 V2 TV V V V Output Signal Vout1 Y/VinS1 Y/VinS1 + CinS1 Y/VinS1 Y/VinS2 Y/VinS2 + CinS2 Y/VinS2 VinV1 VinV2 VinTV * * * * * * 1 1 1 0 1 1 * Open 1 1 0 1 Low 0 0 1 S Input Discrimination CS1 Low 0 * Open 1 0 0 CS2 Bus Data Input Select (main) B12 B11 B10 Do not use [100] for the input select data. Note5: FV: Forced Video Mode. Main L/R Select: Terminal 37 and 35 Output Signal Mode Main L/R Output Signal Lout1 LinS1 LinS2 LinV1 LinV2 LinTV LinTV Rout1 RinS1 RinS2 RinV1 RinV2 RinTV RinTV 1 0 Bus Data Forced TV Voice B03 Input Select (main) B12 0 0 1 1 1 * B11 0 1 0 1 1 * B10 * * 1 0 1 * Input S1 S2 V1 V2 TV TV Do not use [100] for the input select data. 15 2005-11-15 TA1218ANG Sub (PIP) Video Select: Terminal 42 Output Signal Mode INPUT S/V V S1 S FV V S2 S FV V1 V2 TV V V V Output Signal Vout2 Y/VinS1 Y/VinS1 + CinS1 Y/VinS1 Y/VinS2 Y/VinS2 + CinS2 Y/VinS2 Vin1 Vin2 VinTV * * * * * * 1 1 1 1 1 1 * Open 1 1 0 1 Low 0 0 1 Low 0 * Open 1 0 0 S Input Discrimination B22 Bus Data Input Select (sub) B21 B20 Do not use [100] for the input select data. Sub L/R Select: Terminal 1 and 2 Output Signal Mode SUB L/R Output Signal Lout2 LinS1 LinS2 LinV1 LinV2 LinTV LinTV Rout2 RinS1 RinS2 RinV1 RinV2 RinTV RinTV 1 0 Bus Data Forced TV Voice B03 B22 0 0 1 1 1 * Input Select (sub) B21 0 1 0 1 1 * B20 * * 1 0 1 * Input S1 S2 V1 V2 TV TV Do not use [100] for the input select data. 16 2005-11-15 TA1218ANG Y Output Select: Terminal 30 Output Signal Mode Input Through Yin S1 V through Y through Yin S2 V through Y through V1 Yin V through V2 Yin V through TV Yin V through Y Output Signal Yout Yin Y/VinS1 Y/VinS1 Yin Y/VinS2 Y/VinS2 Yin VinV1 Yin VinV2 Yin VinTV TV V 1 V2 V V1 S2 S V S1 S V or FV 1 * 0 1 0 1 0 V or FV Bus Data Main V Select Mode (see table 2-2.) Y Output Switching B01 0 1 * 0 C Output Select: Terminal 34 Output Signal Mode Input Through Cin S1 V through C through Cin S2 V through C through V1 Cin V through V2 Cin V through TV Cin V through Y Output Signal Cout Cin Y/VinS1 CinS1 Cin Y/VinS2 CinS2 Cin VinV1 Cin VinV2 Cin VinTV TV V V2 V 1 0 1 V1 S2 S V S1 S V or FV V or FV Bus Data Main V Select Mode (see table 2-2.) C Output Switching B00 0 1 * 0 1 * 0 1 0 17 2005-11-15 TA1218ANG Sync Detection Select: Terminal 4 Output Signal Mode Detection Select Det Select TV Video Input V1 V2 S1 Vout1 Video Output Vout2 Yout Cout Rout1 Audio Output Lout1 Rout2 Lout2 VinTV VinV1 VinV2 Y/VinS1 Vout1 Vout2 Yout Cout ★ ★ ★ ★ Rout1 Lout1 Rout2 Lout2 1 * 1 0 0 0 Sync 0 1 1 0 1 0 0 0 1 1 Sync 0 0 Sync Output Sync Switching Sync Out B16 Bus Data Sync Detection Switching B15 B14 1 0 1 0 1 0 B13 1 1 0 0 1 1 For Det Select marked by ★, the video input or video output corresponding to data B15, B14, and B13 is selected. Sync Detection Sensitivity Switching Bus Data Mode Detection Sensitivity Switching B17 Sensitivity High Low 1 0 18 2005-11-15 TA1218ANG Audio Mute Mode Output Lout1 Mute off on off Rout1 Lout2 Rout2 LoutTV RoutTV * on off * on off on 0 * 1 * * 1 0 * * * 1 0 * B07 * Bus Data Audio Mute B06 * B05 * B04 0 1 DAC Output Switching Mode Output I/O1 State Open Low I/O2 Open * Low Open I/O3 Low O4 Open * Low O5 Open Low 0 * 1 * * * 1 0 * * * * * 1 0 * * * * 1 0 * B27 * B26 * Bus Data DAC Output Switching B25 * B24 * B23 0 1 19 2005-11-15 TA1218ANG Read Mode Power-On Reset Discrimination Bus Data Mode Power-On Reset B30 Reset on off 1 0 S Input Discrimination Mode Input CinS2 Voltage High (open) Low High (open) CinS1 Low 1 * 0 B32 * Bus Data S Input Discrimination B31 1 0 ADC Input Discrimination Mode Input Voltage High I/O1 Mid Low bottom High Mid I/O2 Low bottom I/O3 High Low 0 * 1 * * * * 0 1 1 1 0 1 0 0 * * * * * B37 B36 Bus Data ADC Input Discrimination B35 B34 0 1 0 1 B33 0 0 1 1 20 2005-11-15 TA1218ANG Outline of I C Bus Control Format (1) Start and stop conditions 2 SDA SCL S Start condition P Stop condition (2) Bit transfer SDA SCL SDA must not be changed SDA can be changed (3) Acknowledgement SDA from Master High impedance SDA from Slave High impedance SCL from Master S 1 8 9 21 2005-11-15 TA1218ANG I2C BUS Conditions Characteristics Low level input voltage High level input voltage Low level output voltage at 3 mA sink current Input current each I/O pin with an input voltage between 0.1 VDD and 0.9 VDD Capacitance for each I/O pin SCL clock frequency Hold time START condition Low period of SCL clock High period of SCL clock Set-up time for a repeated START condition Data hold time Data set-up time Set-up time for STOP condition Bus free time between a STOP and START condition Symbol VIL VIH VOL1 Ii Ci fSCL tHD;STA tLOW tHIGH tSU;STA tHD;DAT tSU;DAT tSU;STO tBUF Min 0 3.0 0 -10 − 0 4.0 4.7 4.0 4.7 500 250 4.0 4.7 Typ. − − − − − − − − − − − − − − Max 1.5 Vcc 0.4 10 10 100 − − − − − − − − Unit V V V µA pF kHz µs µs µs µs ns ns µs µs 22 2005-11-15 TA1218ANG Maximum Ratings Characteristics Supply voltage Power dissipation Input pin voltage Operating temperature Storage temperature Symbol VCC PDMAX (Note6) Vin Topr Tstg GND – 0.3 to Vcc + 0.3 −20 to 65 −55 to 150 V °C °C Rating 14 1800 Unit V mW Note6: When using the device at temperatures above Ta = 25°C, reduce the rated power dissipation by 14.4 mW per degree of centigrade. (see the diagram below.) 1800 (mW) 14.4 mW/°C 1224 Power consumption PD 0 0 25 65 150 Ambient temperature Ta (°C) 23 2005-11-15 TA1218ANG Operating Conditions Characteristics Supply voltage Composite signal input amplitude Y input amplitude Comb Y input amplitude Chroma input amplitude Comb chroma input amplitude Audio input amplitude 33 7, 10, 12, 16, 28 12, 16 30 14, 18 32 5, 6, 8, 9, 11, 13, 15, 17, 29, 31 Test Condition Min 8.1 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Typ. 9.0 1.0 1.0 2.0 286 572 ⎯ Max 9.9 ⎯ ⎯ ⎯ ⎯ ⎯ 6.0 Unit V Vp-p Vp-p Vp-p mVp-p Burst mVp-p Burst Vp-p ⎯ 100IRE 100IRE ⎯ Remark ― Electrical Characteristics Current Consumption Pin No. 33 Pin Name VCC (referenced to VCC = 9 V at Ta = 25°C unless otherwise specified) Symbol ICC Test Circuit ⎯ Min 30 Typ. 47 Max 64 Unit mA 24 2005-11-15 TA1218ANG Pin Voltage Pin No. N 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 23 28 29 30 31 32 33 34 35 36 37 38 39 40 42 F 43 44 45 46 47 48 2 3 5 6 7 8 9 10 11 12 13 15 21 26 27 28 29 30 33 34 35 36 37 38 39 40 42 Lout2 Rout2 Det in Det Select LinTV RinTV VinTV LinV1 RinV1 VinV1 LinS1 Y/VinS1 RinS1 CinS1 LinS2 Y/VinS2 RinS2 CinS2 GND VinV2 LinV2 Yin RinV2 Cin VCC Cout Rout1 Yout Lout1 Vout1 RoutTV LoutTV Vout2 V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 V11 V12 V13 V14 V15 V16 V17 V18 V23 V28 V29 V30 V31 V32 V33 V34 V35 V36 V37 V38 V39 V40 V42 Pin Name Symbol Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min 3.7 3.7 6.3 3.4 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 ⎯ 5.0 5.0 5.0 5.0 5.0 ⎯ 3.5 3.7 3.5 3.7 4.1 3.7 3.7 4.1 Typ. 4.0 4.0 6.6 3.7 5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2 5.2 0 5.2 5.2 5.2 5.2 5.2 9.0 3.8 4.0 3.8 4.0 4.4 4.0 4.0 4.4 Max 4.3 4.3 6.9 4.0 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 5.4 ⎯ 5.4 5.4 5.4 5.4 5.4 ⎯ 4.1 4.3 4.1 4.3 4.7 4.3 4.3 4.7 Unit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V 25 2005-11-15 TA1218ANG DC Characteristics Characteristics Measured Pin Det in VinTV VinV1 VinV2 Y/VinS1 Y/VinS2 CinS1 CinS2 Yin Input pin Input resistance Cin LinTV RinTV LinV1 RinV1 LinV2 RinV2 LinS1 RinS1 LinS2 RinS2 Det Select Vout1 Vout2 Yout Output pin Output resistance Cout LoutTV RoutTV Lout1 Rout1 Lout2 Rout2 CinS1 S mode discrimination voltage CinS2 VthC2 ⎯ ⎯ ⎯ 1.75 2.25 2.75 V Symbol R3 R7 R10 R28 R12 R16 R14 R18 R30 R32 R5 R6 R8 R9 R29 R31 R11 R13 R15 R17 R4 R38 R42 R36 R34 R40 R39 R37 R35 R1 R2 VthC1 Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min. 10 20 20 20 20 20 20 20 40 40 49 49 49 49 49 49 49 49 49 49 17 13 13 13 13 20 20 20 20 20 20 1.75 Typ. 18 30 30 30 30 30 30 30 60 60 70 70 70 70 70 70 70 70 70 70 35 25 25 25 25 45 45 45 45 45 45 2.25 Max. 30 40 40 40 40 40 40 40 80 80 100 100 100 100 100 100 100 100 100 100 53 50 50 50 50 90 90 90 90 90 90 2.75 Unit kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ Ω Ω Ω Ω Ω Ω Ω Ω Ω Ω Ω V Voltage on pin 14 at which data B31 changes. Voltage on pin 18 at which data B32 changes. Voltage on pin 32 at which voice is muted. Voltage on pin 27 at which the slave address changes. Measure a voltage change ∆V on each pin when a current of 100 µA flows into the pin. Then calculate the output resistance value R. R = ∆V/100 µA [Ω] Measure a change ∆I in the current flowing into each pin when the voltage is raised by 0.5V. Then calculate the input resistance value R. R = 0.5 V/∆I [Ω] Remark External mute ON voltage Cin VthM 1.75 2.25 2.75 V Address switching voltage Address VthA 1.75 2.25 2.75 V 26 2005-11-15 TA1218ANG Characteristics Measured Pin Symbol Test Circuit ⎯ Min. Typ. Max. Unit Remark Low-bottom threshold level of I/O1 input (pin 19 ). Mid-Low threshold level of I/O1 input (pin 19 ). High-Mid threshold level of I/O1 input (pin 19) Low-bottom threshold level of I/O2 input (pin 20 ). Mid-Low threshold level of I/O2 input(pin 20) High-Mid threshold level of I/O2 input (pin 20 ). Hig-Low threshold level of I/O3 input (pin 21). I/O1 VthI1L 0.55 0.75 0.95 V I/O1 VthI1M ⎯ 2.5 3.0 3.5 V I/O1 Vthl1H ⎯ 7.5 8.0 8.5 V ADC input discrimination voltage I/O2 VthI2L ⎯ 1.75 2.25 2.75 V I/O2 Vthl2M ⎯ 2.5 3.0 3.5 V I/O2 VthI2H ⎯ 7.5 8.0 8.5 V I/O3 VthI3 ⎯ 1.75 2.25 2.75 V 27 2005-11-15 TA1218ANG AC Characteristics Characteristics Select Mode VinTV VinV1 Vout1 Input dynamic range VinV2 Y/VinS1 CinS1 Y/VinS2 CinS2 VinTV VinV1 Vout1 Gain VinV2 Y/VinS1 CinS1 Y/VinS2 CinS2 VinTV VinV1 VinV2 Vout1 Frequency response Y/VinS1 CinS1 Y/VinS2 CinS2 VinTV VinV1 VinV2 Vout1 Crosstalk Y/VinS1 CinS1 Y/VinS2 CinS2 VinTV VinV1 Vout2 Input dynamic range VinV2 Y/VinS1 CinS1 Y/VinS2 CinS2 Symbol VDR7V1 VDR10V1 VDR28V1 VDR12V1 VDR14V1 VDR16V1 VDR18V1 G7V1 G10V1 G28V1 G12V1 G14V1 G16V1 G18V1 F7V1 F10V1 F28V1 F12V1 F14V1 F16V1 F18V1 CT7V1 CT10V1 CT28V1 CT12V1 CT14V1 CT16V1 CT18V1 VDR7V2 VDR10V2 VDR28V2 VDR12V2 VDR14V2 VDR16V2 VDR18V2 Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min. 1.5 1.5 1.5 1.5 1.5 1.5 1.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 10 10 10 10 10 10 10 55 55 55 55 55 55 55 1.5 1.5 1.5 1.5 1.5 1.5 1.5 Typ. 2.0 2.0 2.0 2.0 2.0 2.0 2.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 60 60 60 60 60 60 60 2.0 2.0 2.0 2.0 2.0 2.0 2.0 Max. ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 6.5 6.5 6.5 6.5 6.5 6.5 6.5 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Unit Vp-p Vp-p Vp-p Vp-p Vp-p Vp-p Vp-p dB dB dB dB dB dB dB MHz MHz MHz MHz MHz MHz MHz dB dB dB dB dB dB dB Vp-p Vp-p Vp-p Vp-p Vp-p Vp-p Vp-p (1) Apply a 1.0 Vp-p sine wave to each input pin. (2) In each select mode, measure a frequency at which the output amplitude on pin 38 is 3dB down from the 15 kHz applied level. (1) Apply a 3.58 MHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare signal output from the selected pin with leakage components from nonselected pins to find a crosstalk. (1) Apply a 15 kHz sine wave to each input pin. (2) In each select mode, measure an input amplitude at which the output waveform on pin 42 begins to be distorted. (1) Apply a 15 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, find the gain between input and output. Test Method (1) Apply a 15 kHz sine wave to each input pin. (2) In each select mode, measure an input amplitude at which the output waveform on pin 38 begins to be distorted. 28 2005-11-15 TA1218ANG Characteristics Select Mode VinTV VinV1 Vout2 Gain VinV2 Y/VinS1 CinS1 Y/VinS2 CinS2 VinTV VinV1 VinV2 Vout2 Frequency response Y/VinS1 CinS1 Y/VinS2 CinS2 VinTV VinV1 VinV2 Vout2 Crosstalk Y/VinS1 CinS1 Y/VinS2 CinS2 VinTV VinV1 Yout Input dynamic range VinV2 Y/VinS1 Y/VinS2 Yin VinTV VinV1 Yout Gain VinV2 Y/VinS1 Y/VinS2 Yin Symbol G7V2 G10V2 G28V2 G12V2 G14V2 G16V2 G18V2 F7V2 F10V2 F28V2 F12V2 F14V2 F16V2 F18V2 CT7V2 CT10V2 CT28V2 CT12V2 CT14V2 CT16V2 CT18V2 VDR7Y VDR10Y VDR28Y VDR12Y VDR16Y VDR30Y G7Y G10Y G28Y G12Y G16Y G30Y Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min. 5.5 5.5 5.5 5.5 5.5 5.5 5.5 10 10 10 10 10 10 10 55 55 55 55 55 55 55 1.5 1.5 1.5 1.5 1.5 5.0 5.5 5.5 5.5 5.5 5.5 −0.5 Typ. 6.0 6.0 6.0 6.0 6.0 6.0 6.0 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 60 60 60 60 60 60 60 2.0 2.0 2.0 2.0 2.0 5.5 6.0 6.0 6.0 6.0 6.0 0 Max. 6.5 6.5 6.5 6.5 6.5 6.5 6.5 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 6.5 6.5 6.5 6.5 6.5 0.5 Unit dB dB dB dB dB dB dB MHz MHz MHz MHz MHz MHz MHz dB dB dB dB dB dB dB Vp-p Vp-p Vp-p Vp-p Vp-p Vp-p dB dB dB dB dB dB (1) Apply a 1.0 Vp-p sine wave to each input pin. (2) In each select mode, measure a frequency at which the output amplitude on pin 42 is 3dB down from the 15 kHz applied level. (1) Apply a 3.58 MHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare signal output from the selected pin with leakage components from nonselected pins to find a crosstalk. (1) Apply a 15 kHz sine wave to each input pin. (2) In each select mode, measure an input amplitude at which the output waveform on pin 36 begins to be distorted. (1) Apply a 15 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, find the gain between input and output. (1) Apply a 15 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, find the gain between input and output. Test Method 29 2005-11-15 TA1218ANG Characteristics Select Mode VinTV VinV1 Yout Frequency response VinV2 Y/VinS1 Y/VinS2 Yin VinTV VinV1 Yout Crosstalk VinV2 Y/VinS1 Y/VinS2 Yin VinTV VinV1 VinV2 Cout Input dynamic range Y/VinS1 CinS1 Y/VinS2 CinS2 Cin VinTV VinV1 VinV2 Cout Gain Y/VinS1 CinS1 Y/VinS2 CinS2 Cin Symbol F7Y F10Y F28Y F12Y F16Y F30Y CT7Y CT10Y CT28Y CT12Y CT16Y CT30Y VDR7C VDR10C VDR28C VDR12C VDR14C VDR16C VDR18C VDR32C G7C G10C G28C G12C G14C G16C G18C G32C Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min. 10 10 10 10 10 10 55 55 55 55 55 55 1.5 1.5 1.5 1.5 1.5 1.5 1.5 5.0 5.5 5.5 5.5 5.5 5.5 5.5 5.5 −0.5 Typ. ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 60 60 60 60 60 60 2.0 2.0 2.0 2.0 2.0 2.0 2.0 5.5 6.0 6.0 6.0 6.0 6.0 6.0 6.0 0 Max. ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 6.5 6.5 6.5 6.5 6.5 6.5 6.5 0.5 Unit MHz MHz MHz MHz MHz MHz dB dB dB dB dB dB Vp-p Vp-p Vp-p Vp-p Vp-p Vp-p Vp-p Vp-p dB dB dB dB dB dB dB dB (1) Apply a 15 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, find the gain between input and output. (1) Apply a 15 kHz sine wave to each input pin. (2) In each select mode, measure an input amplitude at which the output waveform on pin 34 begins to be distorted. Test Method (1) Apply a 1.0 Vp-p sine wave to each input pin. (2) In each select mode, measure a frequency at which the output amplitude on pin 36 is 3dB down from the 15 kHz applied level. (1) Apply a 3.58 MHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare signal output from the selected pin with leakage components from nonselected pins to find a crosstalk. 30 2005-11-15 TA1218ANG Characteristics Select Mode VinTV VinV1 VinV2 Cout Frequency response Y/VinS1 CinS1 Y/VinS2 CinS2 Cin VinTV VinV1 VinV2 Cout Crosstalk Y/VinS1 CinS1 Y/VinS2 CinS2 Cin VinTV VinV1 VinV2 Det select Input dynamic range Y/VinS1 Vout1 Vout2 Yout Cout VinTV VinV1 VinV2 Det select Gain Y/VinS1 Vout1 Vout2 Yout Cout Symbol F7C F10C F28C F12C F14C F16C F18C F32C CT7C CT10C CT28C CT12C CT14C CT16C CT18C CT32C VDR7D VDR10D VDR28D VDR12D VDR38D VDR42D VDR36D VDR34D G7D G10D G28D G12D G38D G42D G36D G34D Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min. 10 10 10 10 10 10 10 10 55 55 55 55 55 55 55 55 5.0 5.0 5.0 5.0 1.5 1.5 1.2 1.2 −0.5 −0.5 −0.5 −0.5 −0.1 −0.1 −0.1 −0.1 Typ. ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 60 60 60 60 60 60 60 60 5.5 5.5 5.5 5.5 2.0 2.0 1.8 1.8 0 0 0 0 0 0 0 0 Max. ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 0.5 0.5 0.5 0.5 0.1 0.1 0.1 0.1 Unit MHz MHz MHz MHz MHz MHz MHz MHz dB dB dB dB dB dB dB dB V V V V V V V V dB dB dB dB dB dB dB dB (1) Apply a 15 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, find the gain between input and output. (1) Apply a 15 kHz sine wave to each input pin. (2) In each select mode, measure an input amplitude at which the output waveform on pin 4 begins to be distorted. Test Method (1) Apply a 1.0 Vp-p sine wave to each input pin. (2) In each select mode, measure a frequency at which the output amplitude on pin 34 is 3dB down from the 15 kHz applied level. (1) Apply a 3.58 MHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare signal output from the selected pin with leakage components from nonselected pins to find a crosstalk. 31 2005-11-15 TA1218ANG Characteristics Select Mode LinTV LinV1 Lout1 Input dynamic range LinV2 LinS1 LinS2 LinTV LinV1 Lout1 Gain LinV2 LinS1 LinS2 LinTV LinV1 Lout1 Frequency response LinV2 LinS1 LinS2 LinTV LinV1 Lout1 Crosstalk LinV2 LinS1 LinS2 LinTV LinV1 Lout1 Mute attenuation LinV2 LinS1 LinS2 Symbol VDR5L1 VDR8L1 VDR29L1 VDR11L1 VDR15L1 G5L1 G8L1 G29L1 G11L1 G15L1 F5L1 F8L1 F29L1 F11L1 F15L1 CT5L1 CT8L1 CT29L1 CT11L1 CT15L1 M5L1 M8L1 M29L1 M11L1 M15L1 Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min. 6.0 6.0 6.0 6.0 6.0 −0.5 −0.5 −0.5 −0.5 −0.5 0.1 0.1 0.1 0.1 0.1 70 70 70 70 70 70 70 70 70 70 Typ. 6.5 6.5 6.5 6.5 6.5 0 0 0 0 0 2.0 2.0 2.0 2.0 2.0 100 100 100 100 100 100 100 100 100 100 Max. ⎯ ⎯ ⎯ ⎯ ⎯ 0.5 0.5 0.5 0.5 0.5 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Unit Vp-p Vp-p Vp-p Vp-p Vp-p dB dB dB dB dB MHz MHz MHz MHz MHz dB dB dB dB dB dB dB dB dB dB Test Method (1) Apply a 1 kHz sine wave to each input pin. (2) In each select mode, measure an input amplitude at which the output waveform on pin 37 begins to be distorted. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, find the gain between input and output. (1) Apply a 1.0 Vp-p sine wave to each input pin. (2) In each select mode, measure a frequency at which the output amplitude on pin 37 is 3dB down from the 1 kHz applied level. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare signal output from the selected pin with leakage components from nonselected pins to find a crosstalk. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare the output amplitudes on pin 37 when mute is turned on and turned off to find mute attenuation. 32 2005-11-15 TA1218ANG Characteristics Select Mode RinTV RinV1 Rout1 Input dynamic range RinV2 RinS1 RinS2 RinTV RinV1 Rout1 Gain RinV2 RinS1 RinS2 RinTV Symbol VDR6R1 VDR9R1 VDR31R1 VDR13R1 VDR17R1 G6R1 G9R1 G31R1 G13R1 G17R1 F6R1 Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min. 6.0 6.0 6.0 6.0 6.0 −0.5 −0.5 −0.5 −0.5 −0.5 0.1 Typ. 6.5 6.5 6.5 6.5 6.5 0 0 0 0 0 2.0 Max. ⎯ ⎯ ⎯ ⎯ ⎯ 0.5 0.5 0.5 0.5 0.5 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Unit Vp-p Vp-p Vp-p Vp-p Vp-p dB dB dB dB dB MHz Test Method (1) Apply a 1 kHz sine wave to each input pin. (2) In each select mode, measure an input amplitude at which the output waveform on pin 35 begins to be distorted. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, find the gain between input and output. (1) Apply a 1.0 Vp-p sine wave to each input pin. (2) In each select mode, measure a frequency at which the output amplitude on pin 35 is 3dB down from the 1 kHz applied level. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare signal output from the selected pin with leakage components from nonselected pins to find a crosstalk. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare the output amplitudes on pin 35 when mute is turned on and turned off to find mute attenuation. RinV1 Rout1 Frequency response F9R1 0.1 2.0 MHz RinV2 F31R1 0.1 2.0 MHz RinS1 F13R1 0.1 2.0 MHz RinS2 RinTV RinV1 Rout1 Crosstalk RinV2 RinS1 RinS2 RinTV RinV1 Rout1 Mute attenuation RinV2 RinS1 RinS2 F17R1 0.1 2.0 MHz CT6R1 CT9R1 CT31R1 CT13R1 CT17R1 M6R1 M9R1 M31R1 M13R1 M17R1 70 70 70 70 70 70 70 70 70 70 100 100 100 100 100 100 100 100 100 100 dB dB dB dB dB dB dB dB dB dB 33 2005-11-15 TA1218ANG Characteristics Select Mode LinTV LinV1 Lout2 Input dynamic range LinV2 LinS1 LinS2 LinTV LinV1 Lout2 Gain LinV2 LinS1 LinS2 LinTV LinV1 Lout2 Frequency response LinV2 LinS1 LinS2 LinTV LinV1 Lout2 Crosstalk LinV2 LinS1 LinS2 LinTV LinV1 Lout2 Mute attenuation LinV2 LinS1 LinS2 Symbol VDR5L2 VDR8L2 VDR29L2 VDR11L2 VDR15L2 G5L2 G8L2 G29L2 G11L2 G15L2 F5L2 F8L2 F29L2 F11L2 F15L2 CT5L2 CT8L2 CT29L2 CT11L2 CT15L2 M5L2 M8L2 M29L2 M11L2 M15L2 Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min. 6.0 6.0 6.0 6.0 6.0 −0.5 −0.5 −0.5 −0.5 −0.5 0.1 0.1 0.1 0.1 0.1 70 70 70 70 70 70 70 70 70 70 Typ. 6.5 6.5 6.5 6.5 6.5 0 0 0 0 0 2.0 2.0 2.0 2.0 2.0 100 100 100 100 100 100 100 100 100 100 Max. ⎯ ⎯ ⎯ ⎯ ⎯ 0.5 0.5 0.5 0.5 0.5 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Unit Vp-p Vp-p Vp-p Vp-p Vp-p dB dB dB dB dB MHz MHz MHz MHz MHz dB dB dB dB dB dB dB dB dB dB Test Method (1) Apply a 1 kHz sine wave to each input pin. (2) In each select mode, measure an input amplitude at which the output waveform on pin 1 begins to be distorted. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, find the gain between input and output. (1) Apply a 1.0 Vp-p sine wave to each input pin. (2) In each select mode, measure a frequency at which the output amplitude on pin 1 is 3dB down from the 1 kHz applied level. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare signal output from the selected pin with leakage components from nonselected pins to find a crosstalk. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare the output amplitudes on pin 1 when mute is turned on and turned off to find mute attenuation. 34 2005-11-15 TA1218ANG Characteristics Select Mode RinTV RinV1 Rout2 Input dynamic range RinV2 RinS1 RinS2 RinTV RinV1 Rout2 Gain RinV2 RinS1 RinS2 RinTV RinV1 Rout2 Frequency response RinV2 RinS1 RinS2 RinTV RinV1 Rout2 Crosstalk RinV2 RinS1 RinS2 RinTV RinV1 Rout2 Mute attenuation RinV2 RinS1 RinS2 Symbol VDR6R2 VDR9R2 VDR31R2 VDR13R2 VDR17R2 G6R2 G9R2 G31R2 G13R2 G17R2 F6R2 F9R2 F31R2 F13R2 F17R2 CT6R2 CT9R2 CT31R2 CT13R2 CT17R2 M6R2 M9R2 M31R2 M13R2 M17R2 Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min. 6.0 6.0 6.0 6.0 6.0 −0.5 −0.5 −0.5 −0.5 −0.5 0.1 0.1 0.1 0.1 0.1 70 70 70 70 70 70 70 70 70 70 Typ. 6.5 6.5 6.5 6.5 6.5 0 0 0 0 0 2.0 2.0 2.0 2.0 2.0 100 100 100 100 100 100 100 100 100 100 Max. ⎯ ⎯ ⎯ ⎯ ⎯ 0.5 0.5 0.5 0.5 0.5 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Unit Vp-p Vp-p Vp-p Vp-p Vp-p dB dB dB dB dB MHz MHz MHz MHz MHz dB dB dB dB dB dB dB dB dB dB Test Method (1) Apply a 1 kHz sine wave to each input pin. (2) In each select mode, measure an input amplitude at which the output waveform on pin 2 begins to be distorted. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, find the gain between input and output. (1) Apply a 1.0 Vp-p sine wave to each input pin. (2) In each select mode, measure a frequency at which the output amplitude on pin 2 is 3dB down from the 1 kHz applied level. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare signal output from the selected pin with leakage components from nonselected pins to find a crosstalk. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) In each select mode, compare the output amplitudes on pin 2 when mute is turned on and turned off to find mute attenuation. While applying a 1 kHz sine wave to pin 5 , measure an input amplitude at which the output waveform on pin 40 begins to be distorted. LoutTV Input dynamic range LinTV VDR5LTV ⎯ 6.0 6.5 ⎯ Vp-p 35 2005-11-15 TA1218ANG Characteristics Select Mode Symbol Test Circuit Min. Typ. Max. Unit Test Method While applying a 1 kHz, 1.0 Vp-p sine wave to pin 5 , find the gain between pins 5 and 40 . While applying a 1.0 Vp-p sine wave to pin 5, measure a frequency at which the output waveform on pin 40 is 3dB down from the 1 kHz applied level. (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) Compare the output amplitude when LinTV is selected with leakage components from nonselected pins to find a crosstalk. While applying a 1 kHz, 1.0 Vp-p sine wave to pin 5, compare the output amplitudes on pin 40 when mute is turned on and turned off to find mute attenuation. While applying a 1 kHz sine wave to pin 6 , measure an input amplitude at which the output waveform on pin 39 begins to be distorted. While applying a 1 kHz, 1.0 Vp-p sine wave to pin 6 , find the gain between pins 6 and 39. While applying a 1.0 Vp-p sine wave to pin 6, measure a frequency at which the output waveform on pin 39 is 3dB down from the 1 kHz applied level. LoutTV Gain LinTV G5LTV ⎯ −0.5 0 0.5 dB LoutTV Frequency response LinTV F5LTV ⎯ 0.1 2.0 ⎯ MHz LinTV LinV1 LoutTV Crosstalk LinV2 LinS1 LinS2 CT5LTV CT8LTV CT29LTV CT11LTV CT15LTV ⎯ ⎯ ⎯ ⎯ ⎯ 70 70 70 70 70 100 100 100 100 100 ⎯ ⎯ ⎯ ⎯ ⎯ dB dB dB dB dB LoutTV Mute attenuation LinTV M5LTV ⎯ 70 100 ⎯ dB RoutTV Input dynamic range RinTV VDR6RTV ⎯ 6.0 6.5 ⎯ Vp-p RoutTV Gain RinTV G6RTV ⎯ −0.5 0 0.5 dB RoutTV Frequency response RinTV F6RTV ⎯ 0.1 2.0 ⎯ MHz 36 2005-11-15 TA1218ANG Characteristics Select Mode RinTV RinV1 RoutTV Crosstalk RinV2 RinS1 RinS2 Symbol CT6RTV CT9RTV CT31RTV CT13RTV CT17RTV Test Circuit ⎯ ⎯ ⎯ ⎯ ⎯ Min. 70 70 70 70 70 Typ. 100 100 100 100 100 Max. ⎯ ⎯ ⎯ ⎯ ⎯ Unit dB dB dB dB dB Test Method (1) Apply a 1 kHz, 1.0 Vp-p sine wave to each input pin. (2) Compare the output amplitude when RinTV is selected with leakage components from nonselected pins While applying a 1 kHz, 1.0 Vp-p sine wave to pin 6, compare the output amplitudes on pin 39 when mute is turned on and turned off to find mute attenuation. RoutTV Mute attenuation RinTV M6RTV ⎯ 70 100 ⎯ dB 37 2005-11-15 TA1218ANG Application Circuit 1 Lout2 2 Rout2 0.01 µF 3 Det in 4 Det Select 5 LinTV 6 RinTV 7 VinTV 8 LinV1 9 RinV1 10 VinV1 11 LinS1 12 Y/VinS1 13 RinS1 14 CinS1 15 LinS2 16 Y/VinS2 17 RinS2 18 CinS2 19 I/O1 20 I/O2 21 I/O3 TA1218ANG Vout2 42 4.7 kΩ O5 41 LoutTV 40 RoutTV 39 Vout1 38 Lout1 37 Yout 36 Rout1 35 Cout 34 VCC 33 Cin 32 RinV2 31 Yin 30 LinV2 29 VinV2 28 Address 27 Sync out 26 SDA 25 SCL 24 GND 23 4.7 kΩ 0.01 µF O4 22 0.01 µF VCC = 9 V 2.2 µF 2.2 µF 47 µF 2.2 µF 2.2 µF 47 µF 2.2 µF 47 µF 2.2 µF 0.01 µF 2.2 µF 47 µF 2.2 µF 0.01 µF 0.01 µF 4.7 kΩ 4.7 kΩ 4.7 kΩ 0.01 µF 0.01 µF 2.2 µF 47 µF 2.2 µF 47 µF 10 kΩ To microcomputer 0.01 µF 0.01 µF 100 µF 38 2005-11-15 TA1218ANG Package Dimensions Weight: 4.13 g (typ.) 39 2005-11-15 TA1218ANG 40 2005-11-15