TA4805BF

TA48015,018,025,033,05,08,09BF TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic TA48015BF,TA48018BF,TA48025BF TA48033BF,TA4805BF,TA4808BF,TA4809BF 1 A Three-Terminal Low-Dropout Voltage Regulator The TA48***BF series consists of fixed-positive-output, low-dropout regulators with an output current of 1 A (max) that utilize V-PNP transistors for the output stage. In response to the need for low-voltage and low-power dissipation devices for use in consumer electronics and industrial appliances, the series offers devices with low output voltages:1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V, 8 V, 9 V Features • • • • • • • • • Maximum output current: 1 A Low output voltage Low standby current Low-dropout voltage COUT (reference) Protection function Package type : 1.5 / 1.8 / 2.5 / 3.3 / 5.0 / 8.0 / 9.0 V : 850 μA (typ.) (@IOUT = 0 A) : VD = 0.5 V (max) (@IOUT = 0.5 A) (1.1V only for TA48015BF) : 2.2 μF(multi-layer ceramic type) : Overcurrent protection / overheating protection / SOA : Surface-mount New PW-Mold Output voltage accuracy : VOUT ± 3% (@Tj = 25°C) Low starting quiescent current Weight HSOP3-P-2.30D : 0.36 g (typ.) Pin Assignment Marking side 1 IN 3 2 GND OUT The product(s) in this document (“Product”) contain functions intended to protect the Product from temporary small overloads such as minor short-term overcurrent or overheating. The protective functions do not necessarily protect Product under all circumstances. When incorporating Product into your system, please design the system (1) to avoid such overloads upon the Product, and (2) to shut down or otherwise relieve the Product of such overload conditions immediately upon occurrence. For details, please refer to the notes appearing below in this document and other documents referenced in this document. 1 2009-02-02 TA48015,018,025,033,05,08,09BF Marking TA48***BF Series 3 Note: A line under a Lot No. identifies the indication of product Labels. [[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]] Product No. (or abbreviation code) Lot No. Note 48***BF 1 2 Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. The RoHS is the Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Note1: The “***” part of each product number varies according to the output voltage of the product. How to Order Product No. TA48***BF (T6L1, NQ) (Note2) Package New PW-Mold: Surface-mount Packing Type and Unit for Orders Tape (2000 pcs/reel) Note 2: The “***” in each product number is replaced with the output voltage of each product. Block Diagram IN 1 Over current protection Constant current circuit Reference OUT 2 voltage circuit Thermal shutdown circuit GND 3 2 2009-02-02 TA48015,018,025,033,05,08,09BF Absolute Maximum Ratings (Ta = 25°C) Characteristic Input voltage Output current Operating junction temperature Junction temperature Storage temperature Power dissipation Ta = 25°C Tc= 25°C Symbol VIN IOUT Tjopr Tj Tstg PD Rating 16 1 -40 to 150 150 −55 to 150 1 10 Unit V A °C °C °C W Note 1: Do not apply external current and voltage (including negative voltage) to non-specified pins. Note 2: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Thermal Characteristics Characteristic Thermal resistance, junction to ambient Thermal resistance, junction to case Symbol R th (j−a) R th (j−c) Max 125 12.5 Unit ℃/ W ℃/ W Protection Function (reference) Characteristics Thermal shutdown Thermal shutdown hysteresis width Peak circuit current Symbol TSD TSD(hys) IPEAK Test Condition VIN = 3.4 V (015 to 018BF) / 3.5 V (025BF) 4.3 V (033BF) / 6.0 V (05BF) / 9.0 V (08BF) / 10.0 V (09BF) VIN = VOUT + 2 V, Tj = 25°C VIN = 12 V, Tj = 25°C VIN = VOUT + 2 V, Tj = 25°C VIN = 12 V, Tj = 25°C Min 150 ⎯ ⎯ ⎯ ⎯ ⎯ Typ. 175 20 1.7 1.8 1.2 1.3 Max ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Unit °C °C A Short circuit current ISC A Note 3: Ensure that the devices operate within the limits of the maximum rating when in actual use. 3 2009-02-02 TA48015,018,025,033,05,08,09BF TA48015BF Electrical Characteristics (CIN = 0.33 μF, COUT = 2.2 μF, Tj = 25°C, unless otherwise specified) Characteristics Symbol Test Conditions VIN = 3.5 V, IOUT = 0.5 A Output voltage VOUT Reg･line Reg･load IB 3.4 V ≤ VIN ≤ 6.5 V, 5 mA ≤ IOUT ≤ 1 A, 0°C ≤ Tj ≤ 125°C 3.4 V ≤ VIN ≤ 6.5 V, IOUT = 0.5 A VIN = 3.5 V, 5 mA ≤ IOUT ≤ 1 A 3.4 V ≤ VIN ≤ 6.5 V, IOUT = 0 A 3.4 V ≤ VIN ≤ 6.5 V, IOUT = 1 A VIN = 2.1 V, IOUT = 0 A VIN = 3.4 V, IOUT = 1 A VIN = 3.5 V, IOUT = 50 mA, 10 Hz ≤ f ≤ 100 kHz 3.5 V ≤ VIN ≤ 6.5 V, IOUT = 50 mA, f = 120 Hz IOUT = 0.5 A IOUT = 1 A VIN = 3.5 V, IOUT = 5 mA, 0°C ≤ Tj ≤ 125°C Min 1.455 1.44 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 54 ⎯ ⎯ ⎯ Typ. 1.500 1.50 4.5 2 0.85 10 0.7 13.0 75 65 0.95 1.9 0.14 Max 1.545 1.56 20.0 20 1.70 20 2.3 28.5 ⎯ ⎯ 1.10 ⎯ ⎯ V Unit Line regulation Load regulation Quiescent current mV mV mA Starting quiescent current Output noise voltage Ripple rejection Dropout voltage Average temperature coefficient of output voltage IBstart VNO R.R. VD TCVO mA μVrms dB V mV/°C TA48018BF Electrical Characteristics (CIN = 0.33 μF, COUT = 2.2 μF, Tj = 25°C, unless otherwise specified) Characteristics Symbol Test Conditions VIN = 3.8 V, IOUT = 0.5 A Output voltage VOUT Reg･line Reg･load IB 3.4 V ≤ VIN ≤ 6.8 V, 5 mA ≤ IOUT ≤ 1 A, 0°C ≤ Tj ≤ 125°C 3.4 V ≤ VIN ≤ 6.8 V, IOUT = 0.5 A VIN = 3.8 V, 5 mA ≤ IOUT ≤ 1 A 3.4 V ≤ VIN ≤ 6.8 V, IOUT = 0 A 3.4 V ≤ VIN ≤ 6.8 V, IOUT = 1 A VIN = 2.1 V, IOUT = 0 A VIN = 3.4 V, IOUT = 1 A VIN = 3.8 V, IOUT = 50 mA, 10 Hz ≤ f ≤ 100 kHz 3.4 V ≤ VIN < 6.8 V, IOUT = 50 mA, = f = 120 Hz IOUT = 0.5 A IOUT = 1 A VIN = 3.8 V, IOUT = 5 mA, 0°C ≤ Tj ≤ 125°C Min 1.746 1.728 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 54 ⎯ ⎯ ⎯ Typ. 1.800 1.800 5.6 2.4 0.85 10 0.7 14.0 75 66 0.41 1.6 0.15 Max 1.854 1.872 20.0 20.0 1.70 20 2.3 28.5 ⎯ ⎯ 0.50 ⎯ ⎯ V Unit Line regulation Load regulation Quiescent current mV mV mA Starting quiescent current Output noise voltage Ripple rejection Dropout voltage Average temperature coefficient of output voltage IBstart VNO R.R. VD TCVO mA μVrms dB V mV/°C 4 2009-02-02 TA48015,018,025,033,05,08,09BF TA48025BF Electrical Characteristics (CIN = 0.33 μF, COUT = 2.2 μF, Tj = 25°C, unless otherwise specified) Characteristics Symbol Test Conditions VIN = 4.5 V, IOUT = 0.5 A Output voltage VOUT Reg･line Reg･load IB 3.5 V ≤ VIN ≤ 7.5 V, 5 mA ≤ IOUT ≤ 1 A, 0°C ≤ Tj ≤ 125°C 3.5 V ≤ VIN ≤ 7.5 V, IOUT = 0.5 A VIN = 4.5 V, 5 mA ≤ IOUT ≤ 1 A 3.5 V ≤ VIN ≤ 7.5 V, IOUT = 0 A 3.5 V ≤ VIN ≤ 7.5 V, IOUT = 1 A VIN = 2.1 V, IOUT = 0 A VIN = 3.4 V, IOUT = 1 A VIN = 4.5 V, IOUT = 50 mA, 10 Hz ≤ f ≤ 100 kHz 3.5 V ≤ VIN ≤ 7.5 V, IOUT = 50 mA, f = 120 Hz IOUT = 0.5 A IOUT = 1 A VIN = 4.5 V, IOUT = 5 mA, 0°C ≤ Tj ≤ 125°C Min 2.425 2.4 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 52 ⎯ ⎯ ⎯ Typ. 2.500 2.5 6.7 2.9 0.85 10 2.2 16.0 95 64 0.32 0.88 0.2 Max 2.575 2.6 20.0 20.0 1.70 20 3.5 28.5 ⎯ ⎯ 0.50 ⎯ ⎯ V Unit Line regulation Load regulation Quiescent current mV mV mA Starting quiescent current Output noise voltage Ripple rejection Dropout voltage Average temperature coefficient of output voltage IBstart VNO R.R. VD TCVO mA μVrms dB V mV/°C TA48033BF Electrical Characteristics (CIN = 0.33 μF, COUT = 2.2 μF, Tj = 25°C, unless otherwise specified) Characteristics Symbol Test Conditions VIN = 5.3 V, IOUT = 0.5 A Output voltage VOUT Reg･line Reg･load IB 4.3 V ≤ VIN ≤ 8.8 V, 5 mA ≤ IOUT ≤ 1 A, 0°C ≤ Tj ≤ 125°C 4.3 V ≤ VIN ≤ 8.8 V, IOUT = 0.5 A VIN = 5.3 V, 5 mA ≤ IOUT ≤ 1 A 4.3 V ≤ VIN ≤ 8.8 V, IOUT = 0 A 4.3 V ≤ VIN ≤ 8.8 V, IOUT = 1 A VIN = 2.1 V, IOUT = 0 A VIN = 3.5 V, IOUT = 1 A VIN = 5.3 V, IOUT = 50 mA, 10 Hz ≤ f ≤ 100 kHz 4.3 V ≤ VIN ≤ 8.8 V, IOUT = 50 mA, f = 120 Hz IOUT = 0.5 A IOUT = 1 A VIN = 5.3 V, IOUT = 5 mA, 0°C ≤ Tj ≤ 125°C Min 3.201 3.168 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 50 ⎯ ⎯ ⎯ Typ. 3.300 3.300 8.3 3.7 0.85 10 3.3 17.0 115 62 0.32 0.69 0.3 Max 3.399 3.432 20.0 20.0 1.70 20 4.0 28.5 ⎯ ⎯ 0.50 ⎯ ⎯ V Unit Line regulation Load regulation Quiescent current mV mV mA Starting quiescent current Output noise voltage Ripple rejection Dropout voltage Average temperature coefficient of output voltage IBstart VNO R.R. VD TCVO mA μVrms dB V mV/°C 5 2009-02-02 TA48015,018,025,033,05,08,09BF TA4805BF Electrical Characteristics (CIN = 0.33 μF, COUT = 2.2 μF, Tj = 25°C, unless otherwise specified) Characteristics Symbol Test Conditions VIN = 7 V, IOUT = 0.5 A Output voltage VOUT Reg･line Reg･load IB 6 V ≤ VIN ≤ 10 V, , 5 mA ≤ IOUT ≤ 1 A, 0°C ≤ Tj ≤ 125°C 6 V ≤ VIN ≤ 10 V, IOUT = 0.5 A VIN = 7 V, 5 mA ≤ IOUT ≤ 1 A 6 V ≤ VIN ≤ 10 V, IOUT = 0 A 6 V ≤ VIN ≤ 10 V, IOUT = 1 A VIN = 2.1 V, IOUT = 0 A VIN = 4.5 V, IOUT = 1 A VIN = 7 V, IOUT = 50 mA, 10 Hz ≤ f ≤ 100 kHz 6 V ≤ VIN ≤ 10 V, IOUT = 50 mA, f = 120 Hz IOUT = 0.5 A IOUT = 1 A VIN = 7 V, IOUT = 5 mA, 0°C ≤ Tj ≤ 125°C Min 4.85 4.8 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 48 ⎯ ⎯ ⎯ Typ. 5.00 5.0 10 4.2 0.85 10 2.5 18.0 150 60 0.32 0.69 0.45 Max 5.15 5.2 20 20.0 1.70 20 4.2 28.5 ⎯ ⎯ 0.50 ⎯ ⎯ V Unit Line regulation Load regulation Quiescent current mV mV mA Starting quiescent current Output n oise voltage Ripple rejection Dropout voltage Average temperature coefficient of output voltage IBstart VNO R.R. VD TCVO mA μVrms dB V mV/°C TA4808BF Electrical Characteristics (CIN = 0.33 μF, COUT = 2.2 μF, Tj = 25°C, unless otherwise specified) Characteristics Symbol Test Conditions VIN = 10 V, IOUT = 0.5 A Output voltage VOUT Reg･line Reg･load IB 9 V ≤ VIN ≤ 13 V, 5 mA ≤ IOUT ≤ 1 A, 0°C ≤ Tj ≤ 125°C 9 V ≤ VIN ≤ 13 V, IOUT = 0.5 A VIN = 10 V, 5 mA ≤ IOUT ≤ 1 A 9 V ≤ VIN ≤ 13 V, IOUT = 0 A 9 V ≤ VIN ≤ 13 V, IOUT = 1 A VIN = 2.1 V, IOUT = 0 A VIN = 7.2 V, IOUT = 1 A VIN = 10 V, IOUT = 50 mA, 10 Hz ≤ f ≤ 100 kHz 9 V ≤ VIN ≤ 13 V, IOUT = 50 mA, f = 120 Hz IOUT = 0.5 A IOUT = 1 A VIN = 10 V, IOUT = 5 mA, 0°C ≤ Tj ≤ 125°C Min 7.76 7.68 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 45 ⎯ ⎯ ⎯ Typ. 8.00 8.00 12.5 9.4 0.9 10 2.6 20.0 225 56 0.32 0.69 0.7 Max 8.24 8.32 20.0 30.0 1.7 20 4.4 28.5 ⎯ ⎯ 0.50 ⎯ ⎯ V Unit Line regulation Load regulation Quiescent current mV mV mA Starting quiescent current Output noise voltage Ripple rejection Dropout voltage Average temperature coefficient of output voltage IBstart VNO R.R. VD TCVO mA μVrms dB V mV/°C 6 2009-02-02 TA48015,018,025,033,05,08,09BF TA4809BF Electrical Characteristics (CIN = 0.33 μF, COUT = 2.2 μF, Tj = 25°C, unless otherwise specified) Characteristics Symbol Test Conditions VIN = 11 V, IOUT = 0.5 A Output voltage VOUT Reg･line Reg･load IB 10 V ≤ VIN ≤ 14 V, 5 mA ≤ IOUT ≤ 1 A, 0°C ≤ Tj ≤ 125°C 10 V ≤ VIN ≤ 14 V, IOUT = 0.5 A VIN = 11 V, 5 mA ≤ IOUT ≤ 1 A 10 V ≤ VIN ≤ 14 V, IOUT = 0 A 10 V ≤ VIN ≤ 14 V, IOUT = 1 A VIN = 2.1 V, IOUT = 0 A VIN = 8.2 V, IOUT = 1 A VIN = 11 V, IOUT = 50 mA, 10 Hz ≤ f ≤ 100 kHz 10 V ≤ VIN ≤ 14 V, IOUT = 50 mA, f = 120 Hz IOUT = 0.5 A IOUT = 1 A VIN = 11 V, IOUT = 5 mA, 0°C ≤ Tj ≤ 125°C Min 8.73 8.64 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 44 ⎯ ⎯ ⎯ Typ. 9.00 9.00 12.5 9.4 0.9 10 2.6 20.0 250 55 0.32 0.69 0.8 Max 9.27 9.36 20.0 30.0 1.7 20 4.4 28.5 ⎯ ⎯ 0.50 ⎯ ⎯ V Unit Line regulation Load regulation Quiescent current mV mV mA Starting quiescent current Output noise voltage Ripple rejection Dropout voltage Average temperature coefficient of output voltage IBstart VNO R.R. VD TCVO mA μVrms dB V mV/°C 7 2009-02-02 TA48015,018,025,033,05,08,09BF Electrical Characteristics for All Products • Tj = 25°C in the measurement conditions of each item is the standard condition when a pulse test is carried out, and any drift in the electrical characteristic due to a rise in the junction temperature of the chip may be disregarded. Standard Application Circuit VIN 1 CIN 0.33 μF TA48xxxBF 3 2 VOUT COUT 2.2 μF • Be sure to connect a capacitor near the input terminal and output terminal between both terminals and GND. The use of a monolithic ceramic capacitor (B Characteristic or X7R) of low ESR (equivalent series resistance) is recommended. The IC may oscillate due to external conditions (output current, temperature, or the type of the capacitor used). The type of capacitor required must be determined by the actual application circuit in which the IC is used. Usage Precautions • The IC might be destroyed if a voltage greater than the input terminal voltage is applied to the output terminal, or if the input terminal is connected to GND during operation. To prevent such an occurrence, connect a diode as in the following diagram. VIN 1 TA48xxxBF 3 2 VOUT • Low voltage Do not apply voltage to the Product that is lower than the minimum operating voltage, or the Product’s protective functions will not operate properly and the Product may be permanently damaged. • Overcurrent Protection The overcurrent protection circuits in the Product are designed to temporarily protect Product from minor overcurrent of brief duration. When the overcurrent protective function in the Product activates, immediately cease application of overcurrent to Product. Improper usage of Product, such as application of current to Product exceeding the absolute maximum ratings, could cause the overcurrent protection circuit not to operate properly and/or damage Product permanently even before the protection circuit starts to operate. • Overheating Protection The thermal shutdown circuits in the Product are designed to temporarily protect Product from minor overheating of brief duration. When the overheating protective function in the Product activates, immediately correct the overheating situation. Improper usage of Product, such as the application of heat to Product exceeding the absolute maximum ratings, could cause the overheating protection circuit not to operate properly and/or damage Product permanently even before the protection circuit starts to operate. 8 2009-02-02 TA48015,018,025,033,05,08,09BF TA48***BF PDmax. – Ta 12 Condition: Ta = Tc Number of IC = 1 Reflow soldering on a 3.8 TA48033BF VIN = 5 V I OUT = 5 mA VOUT – Tj Allowable power dissipation (V) VOUT Output voltage 10 3.6 PDmax. (W) 8 ceramic substrate 3.4 6 50 mm x 50 mm x 0.8 mm 4 30 mm x 30 mm x 0.8 mm 3.2 2 Single 0 3.0 0 20 40 60 80 100 120 140 160 2.8 −50 0 50 100 150 Ambient temperature Ta (°C ) Junction temperature Tj (°C) VOUT – VIN 4 TA48033BF Tj = 25 °C VOUT – I OUT 5 TA48033BF VIN = 5 V Tj = 25 °C 4 (V) VOUT 3 I OUT = 10 mA 0.5 A 0.1 A VOUT Output voltage 4 6 (V) 0 2 3 Output voltage 2 2 1 1 0 0 8 0 0.5 1.0 1.5 2.0 Input voltage VIN (V) Output current IOUT (A ) I B – VIN 14 20 TA48033BF Tj = 25 °C TA48033BF VIN = 5 V Tj = 25 °C I B – I OUT (mA) (mA) IB 0.5 A 12 10 8 6 4 16 IB Quiescent current 12 Quiescent current 8 I OUT = 0 mA 2 0 0.1 A 10 mA 4 0 2 4 6 8 0 0 0.2 0.4 0.6 0.8 1.0 Input voltage VIN (V) Output current IOUT (A ) 9 2009-02-02 TA48015,018,025,033,05,08,09BF I B – Tj 2.0 TA48033BF VIN = 5 V I OUT = 0 A 0.8 TA48033BF Tj = 25 °C VD – I OUT (mA) (V) Dropout voltage VD 1.6 0.6 IB Quiescent current 1.2 0.4 0.8 0.2 0.4 0 −50 0 50 100 150 0 0 0.2 0.4 0.6 0.8 1.0 Junction temperature Tj (°C) Output current IOUT (A ) I PEAK – Tj 2.5 2.4 I PEAK – VD IPEAK (A) Peak output current IPEAK (A) TA48033BF VIN = 5 V 2.0 2.0 1.6 1.5 Peak output current 1.2 1.0 0.8 0.5 0.4 TA48033BF Tj = 25 °C 0 2 4 6 8 0 −50 0 50 100 150 0 Junction temperature Tj (°C) Dropout voltage VD (V) V D – Tj 1.0 TA48033BF 0.8 I OUT = 1 A 0.6 Dropout voltage VD (V) 0.4 0.5 A 0.2 0.1 A 0 -50 0 50 100 150 Junction temperature Tj (°C) 10 2009-02-02 TA48015,018,025,033,05,08,09BF Package Dimensions (TA48xxxBF) HSOP-3-P-2.30D Unit: mm Weight: 0.36 g (typ.) 11 2009-02-02 TA48015,018,025,033,05,08,09BF RESTRICTIONS ON PRODUCT USE • Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively “Product”) without notice. • This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission. • Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the “TOSHIBA Semiconductor Reliability Handbook” and (b) the instructions for the application that Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR APPLICATIONS. • Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. • Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. • Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. • ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. • Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. • Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 12 2009-02-02