TA58L09S,Q(M

TA58L05,06,08,09,10,12,15S TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic TA58L05S,TA58L06S,TA58L08S,TA58L09S TA58L10S,TA58L12S,TA58L15S 250 mA Low Dropout Voltage Regulator The TA58L**S Series consists of fixed-positive-output, low-dropout regulators with an output current of 250 mA (max) that utilize PNP transistors for the output stage. Low dropout voltage and standby current make the TA58L**S Series suitable for applications requiring low power consumption. Features HSIP3-P-2.54A • Maximum output current : 250 mA • Output voltage : 5/ 6/ 8/ 9/ 10/ 12/ 15 V • Output voltage accuracy : VOUT ± 3% (@Tj = 25°C) Weight : 1.7 g (typ.) • Low-dropout voltage : 0.4 V (max) (@IOUT = 200 mA) • Protection function : Overcurrent protection / overheating protection / Reverse connection of power supply / 60 V load dump • Package type : TO-220NIS Pin Assignment Mark 1 IN 3 2 GND OUT Start of commercial production 2004-04 1 2013-11-01 TA58L05,06,08,09,10,12,15S Marking Lot No. 58L**S Note 1 Part No. (or abbreviation code) Note 1: A line under a Lot No. identifies the indication of product Labels. Not underlined: [[Pb]]/INCLUDES > MCV Underlined: [[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]] Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. The RoHS is the Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Note 2: The “**” in each product name is replaced with the output voltage of each product. The product(s) in this document (“Product”) contain functions intended to protect the Product from temporary small overloads such as minor short-term overcurrent, overvoltage, or overheating. The protective functions do not necessarily protect Product under all circumstances. When incorporating Product into your system, please design the system (1) to avoid such overloads upon the Product, and (2) to shut down or otherwise relieve the Product of such overload conditions immediately upon occurrence. For details, please refer to the notes appearing below in this document and other documents referenced in this document. Pin Description Pin No. Symbol Description 1 IN 3 GND Ground terminal 2 OUT Output terminal. Connected by capacitor (COUT) to GND. Input terminal. Connected by capacitor (CIN) to GND. How to Order Product No. TA58L**S(Q) Package (Note 3) Package Type and Capacity TO-220NIS Loose in bag: 50 (1 bag) Note 3: The “**” in each product number is replaced with the output voltage of each product. Block Diagram IN 1 Over current protection OUT 2 － Over voltage/ thermal shutdown + GND 3 2 2013-11-01 TA58L05,06,08,09,10,12,15S Absolute Maximum Rating (Ta = 25°C) Symbol Rating Unit DC VIN (DC) 29 V Pulse VIN (Pulse) 60 (τ=200ms) V Output current IOUT 250 mA Operating temperature Characteristic Input voltage Topr −40 to 105 °C Junction temperature Tj 150 °C Storage temperature Tstg −55 to 150 °C Power dissipation Ta = 25°C PD Tc = 25°C 2 20 W Note 4: Do not apply current and voltage (including reverse polarity) to any pin that is not specified. Note 5: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Thermal Characteristics Characteristic Symbol Max Unit Thermal resistance, junction to ambient Rth (j−a) 62.5 ℃/ W Thermal resistance, junction to case Rth (j−c) 6.25 ℃/ W Protection Function (Reference) Symbol Test Condition Min Typ. Max Unit Thermal shutdown TSD VIN = 14 V (05 to 06S)/ 16 V (08 to 10S)/ 18 V (12S)/ 20 V (15S) ⎯ 170 ⎯ °C Peak circuit current I PEAK VIN = 14 V (05 to 06S)/ 16 V (08 to 10S)/ 18 V (12S)/ 20 V (15S), Tj = 25°C ⎯ 600 ⎯ mA Short circuit current I SC VIN = 14 V (05 to 06S)/ 16 V (08 to 10S)/ 18 V (12S)/ 20 V (15S), Tj = 25°C ⎯ 330 ⎯ mA Overvoltage protection VIN Tj = 25°C 29 33 ⎯ V Characteristic Note 6: Ensure that the devices operate within the limits of the maximum rating when in actual use. Note 7: When the input voltage exceeds 29 V, the overvoltage protection circuit is activated to turn off the output voltage. 3 2013-11-01 TA58L05,06,08,09,10,12,15S TA58L05S Electrical Characteristics (unless otherwise specified, Tj = 25°C) Characteristic Symbol Output voltage VOUT Line regulation Reg･line Load regulation Reg･load Quiescent current IB Dropout voltage VD Test Condition Min Typ. Max VIN = 14 V, IOUT = 10 mA 4.85 5.00 5.15 5.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA, -40°C ≤ Ta ≤ 105°C 4.8 5.0 5.2 9 V ≤ VIN ≤ 16 V, IOUT = 10 mA ⎯ 1 10 5.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA ⎯ 2 15 VIN = 14 V, 10 mA ≤ IOUT ≤ 250 mA ⎯ 10 30 6 V ≤ VIN ≤ 26 V, IOUT = 0 A ⎯ 0.45 1.00 6 V ≤ VIN ≤ 26 V, IOUT = 250 mA ⎯ 25 50 IOUT = 50 mA ⎯ 0.08 0.20 IOUT = 200 mA ⎯ 0.22 0.40 Min Typ. Max VIN = 14 V, IOUT = 10 mA 5.82 6.00 6.18 6.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA, -40°C ≤ Ta ≤ 105°C 5.76 6.00 6.24 10 V ≤ VIN ≤ 17 V, IOUT = 10 mA ⎯ 1 10 6.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA ⎯ 2 15 VIN = 14 V, 10 mA ≤ IOUT ≤ 250 mA ⎯ 10 30 7 V ≤ VIN ≤ 26 V, IOUT = 0 A ⎯ 0.5 1.0 7 V ≤ VIN ≤ 26 V, IOUT = 250 mA ⎯ 25 50 IOUT = 50 mA ⎯ 0.08 0.20 IOUT = 200 mA ⎯ 0.22 0.40 Unit V mV mV mA V TA58L06S Electrical Characteristics (unless otherwise specified, Tj = 25°C) Characteristic Symbol Output voltage VOUT Line regulation Reg･line Load regulation Reg･load Quiescent current IB Dropout voltage VD Test Condition 4 Unit V mV mV mA V 2013-11-01 TA58L05,06,08,09,10,12,15S TA58L08S Electrical Characteristics (unless otherwise specified, Tj = 25°C) Characteristic Output voltage Line regulation Load regulation Quiescent current Dropout voltage Symbol VOUT Reg･line Reg･load IB VD Test Condition Min Typ. Max VIN = 16 V, IOUT = 10mA 7.76 8.00 8.24 8.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA, -40°C ≤ Ta ≤ 105°C 7.68 8.00 8.32 12 V ≤ VIN ≤ 19 V, IOUT = 10 mA ― 1 10 8.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA ― 2 15 VIN = 16 V, 10 mA ≤ IOUT ≤ 250 mA ― 10 40 9 V ≤ VIN ≤ 26 V, IOUT = 0 A ― 0.55 1.00 9 V ≤ VIN ≤ 26 V, IOUT = 250 mA ― 25 50 IOUT = 50 mA ― 0.08 0.20 IOUT = 200 mA ― 0.22 0.40 Min Typ. Max VIN = 16 V, IOUT = 10 mA 8.73 9.00 9.27 9.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA, -40°C ≤ Ta ≤ 105°C 8.64 9.00 9.36 13 V ≤ VIN ≤ 20 V, IOUT = 10 mA ⎯ 1 12 9.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA ⎯ 2 20 VIN = 16 V, 10 mA ≤ IOUT ≤ 250 mA ⎯ 12 40 10 V ≤ VIN ≤ 26 V, IOUT = 0 A ⎯ 0.6 1.0 10 V ≤ VIN ≤ 26 V, IOUT = 250 mA ⎯ 25 50 IOUT = 50 mA ⎯ 0.08 0.20 IOUT = 200 mA ⎯ 0.22 0.40 Unit V mV mV mA V TA58L09S Electrical Characteristics (unless otherwise specified, Tj = 25°C) Characteristic Symbol Output voltage VOUT Line regulation Reg･line Load regulation Reg･load Quiescent current IB Dropout voltage VD Test Condition 5 Unit V mV mV mA V 2013-11-01 TA58L05,06,08,09,10,12,15S TA58L10S Electrical Characteristics (unless otherwise specified, Tj = 25°C) Characteristic Symbol Output voltage VOUT Line regulation Reg･line Load regulation Reg･load Quiescent current IB Dropout voltage VD Test Condition Min Typ. Max VIN = 16 V, IOUT = 10 mA 9.7 10.0 10.3 10.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA, -40°C ≤ Ta ≤ 105°C 9.6 10.0 10.4 14 V ≤ VIN ≤ 21 V, IOUT = 10 mA ⎯ 1 12 10.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA ⎯ 2 20 VIN = 16 V, 10 mA ≤ IOUT ≤ 250 mA ⎯ 12 40 11 V ≤ VIN ≤ 26 V, IOUT = 0 A ⎯ 0.6 1.2 11 V ≤ VIN ≤ 26 V, IOUT = 250 mA ⎯ 25 50 IOUT = 50 mA ⎯ 0.08 0.20 IOUT = 200 mA ⎯ 0.22 0.40 Min Typ. Max VIN = 18 V, IOUT = 10 mA 11.64 12.00 12.36 12.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA, -40°C ≤ Ta ≤ 105°C 11.52 12.00 12.48 16 V ≤ VIN ≤ 23 V, IOUT = 10 mA ⎯ 1 12 12.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA ⎯ 2 20 VIN = 18 V, 10 mA ≤ IOUT ≤ 250 mA ⎯ 20 50 13 V ≤ VIN ≤ 26 V, IOUT = 0 A ⎯ 0.65 1.20 13 V ≤ VIN ≤ 26 V, IOUT = 250 mA ⎯ 25 50 IOUT = 50 mA ⎯ 0.08 0.20 IOUT = 200 mA ⎯ 0.22 0.40 Unit V mV mV mA V TA58L12S Electrical Characteristics (unless otherwise specified, Tj = 25°C) Characteristic Symbol Output voltage VOUT Line regulation Reg･line Load regulation Reg･load Quiescent current IB Dropout voltage VD Test Condition 6 Unit V mV mV mA V 2013-11-01 TA58L05,06,08,09,10,12,15S TA58L15S Electrical Characteristics (unless otherwise specified, Tj = 25°C) Characteristic Symbol Output voltage VOUT Line regulation Reg･line Load regulation Reg･load Quiescent current IB Dropout voltage VD Test Condition Min Typ. Max VIN = 20 V, IOUT = 10 mA 14.55 15.00 15.45 15.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA, -40°C ≤ Ta ≤ 105°C 14.4 15.0 15.6 19 V ≤ VIN ≤ 26 V, IOUT = 10 mA ⎯ 1 12 15.35 V ≤ VIN ≤ 26 V, IOUT = 10 mA ⎯ 2 20 VIN = 20 V, 10 mA ≤ IOUT ≤ 250 mA ⎯ 20 60 16 V ≤ VIN ≤ 26 V, IOUT = 0 A ⎯ 0.75 1.40 16 V ≤ VIN ≤ 26 V, IOUT = 250 mA ⎯ 25 50 IOUT = 50 mA ⎯ 0.08 0.20 IOUT = 200 mA ⎯ 0.22 0.40 7 Unit V mV mV mA V 2013-11-01 TA58L05,06,08,09,10,12,15S Electrical Characteristics Common to All Products • Tj = 25°C in the measurement conditions of each item is the standard condition when a pulse test is carried out, and any drift in the electrical characteristic due to a rise in the junction temperature of the chip may be disregarded. Standard Application Circuit CIN 0.1 μF IN OUT TA58L**S COUT More than 33 μF Load GND • Place CIN as close as possible to the input terminal and GND. Place COUT as close as possible to the output terminal and GND. Although capacitor COUT acts to smooth the dc output voltage during suspension of output oscillation or load change, it might cause output oscillation in a cold environment due to increased capacitor ESR. It is therefore recommended to use a capacitor with small variations temperature sensitivity. Also, ensure that the regulator performance is satisfactory over the operating temperature range of the target system.. Usage Precautions • Low voltage Do not apply voltage to the Product that is lower than the minimum operating voltage, or the Product’s protective functions will not operate properly and the Product may be permanently damaged. • Overcurrent Protection The overcurrent protection circuits in the Product are designed to temporarily protect Product from minor overcurrent of brief duration. When the overcurrent protective function in the Product activates, immediately cease application of overcurrent to Product. Improper usage of Product, such as application of current to Product exceeding the absolute maximum ratings, could cause the overcurrent protection circuit not to operate properly and/or damage Product permanently even before the protection circuit starts to operate. • Overheating Protection The thermal shutdown circuits in the Product are designed to temporarily protect Product from minor overheating of brief duration. When the overheating protective function in the Product activates, immediately correct the overheating situation. Improper usage of Product, such as the application of heat to Product exceeding the absolute maximum ratings, could cause the overheating protection circuit not to operate properly and/or damage Product permanently even before the protection circuit starts to operate. • Overvoltage Protection The overvoltage protection circuits in the Product are designed to temporarily protect Product from minor overvoltage of brief duration. When the overvoltage protective function in the Product activates, immediately cease application of overvoltage to Product. Improper usage of Product, such as application of voltage to Product exceeding the absolute maximum ratings, could cause the overvoltage protection circuit not to operate properly and/or damage Product permanently even before the protection circuit starts to operate. 8 2013-11-01 TA58L05,06,08,09,10,12,15S PDmax. – Ta VOUT – Tj 5.5 Thermal resistance (°C/W) 12 8 4 (V) 16 5.3 VOUT Rth(j-c): 6.25 Rth(j-a): 62.5 5.2 5.0 Single 5.1 4.9 4.8 4.7 4.6 4.5 -50 0 0 TA58L05S VIN = 14 V IOUT = 5 mA 5.4 Output voltage Ta = Tc 20 PDmax. (W) Allowable power dissipation 24 20 40 60 80 100 Ambient temperature 120 140 Ta 160 0 100 Junction temperature (°C ) VOUT – VIN Tj 150 (°C) VOUT – VIN 6 6 TA58L05S Tj = 25 °C (V) (V) 5 VOUT 4 VOUT 4 Output voltage 3 Output voltage TA58L05S Tj = 25 °C 5 3 5 mA 2 IOUT = 0.1 A 1 0 50 0 2 4 Input voltage 6 VIN 8 IOUT = 0.1 A 2 1 0 10 5 mA 0 5 10 (V) 15 Input voltage 20 25 VIN 30 35 (V) IB – VIN VOUT – IOUT 6 30 5 (mA) 25 4 IB 20 Quiescent current Output voltage VOUT (V) TA58L05S Tj = 25 °C 3 2 TA58L05S VIN = 14 V Tj = 25 °C 1 0 0 0.1 15 10 IOUT = 0.1 A 5 5 mA 0.2 0.3 Output current 0.4 IOUT 0.5 0.6 0 0.7 0 (A) 2 4 Input voltage 9 6 VIN 8 10 (V) 2013-11-01 TA58L05,06,08,09,10,12,15S IB – IOUT IB – Tj 1.0 TA58L05S VIN = 14 V IOUT = 0 A 0.8 IB (mA) TA58L05S VIN = 14 V Tj = 25°C Quiescent current (mA) 20 Quiescent current 25 IB 30 15 10 5 0 0 0.05 0.10 0.15 Output current 0.20 IOUT 0.6 0.4 0.2 0 -50 0.25 0 50 Junction temperature (A ) 0.5 0.4 VD (V) 0.5 125°C 85°C 0.2 -40°C 0.1 0 Tj = 25°C 0 0.05 0.10 0.15 Output current 0.20 IOUT IOUT = 0.2 A 0.3 0.2 0.05 A 0.1 (A) 0 50 Tj 150 (°C) IPEAK – VD 0.8 IPEAK (A) TA58L05S VIN = 14 V 0.8 0.6 Peak output current IPEAK (A) 100 Junction temperature IPEAK – Tj Peak output current (°C) 0.4 0 -50 0.25 1.0 0.4 0.2 0 -50 Tj 150 VD – Tj 0.6 Dropout voltage Dropout voltage VD (V) VD – IOUT 0.6 0.3 100 0 50 Junction temperature 100 Tj 0.6 0.4 0.2 TA58L05S Tj = 25°C 0 150 (°C) 0 10 Dropout voltage 10 20 VD 30 (V) 2013-11-01 TA58L05,06,08,09,10,12,15S Package Dimensions HSIP3-P-2.54A Unit: mm Weight: 1.7 g (typ.) 11 2013-11-01 TA58L05,06,08,09,10,12,15S RESTRICTIONS ON PRODUCT USE • Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. • This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. • Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. • PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT ("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales representative. • Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. • Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. • ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. • Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. • Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS. 12 2013-11-01