TB7106F(T2LPP1,Q)

TB7106F TOSHIBA BiCD Integrated Circuit Silicon Monolithic TB7106F Buck DC-DC Converter IC The TB7106F is a single-chip buck DC-DC converter IC that utilizing a chopper circuit. The TB7106F adopts bootstrap system and contains high-speed and low-on-resistance N-channel MOSFETs for the high side main switch to achieve high efficiency. Features • Enables up to 3 A of load current (IOUT) with a minimum of external components. • High efficiency (η = 88% typ.) (@VIN = 12 V, VOUT = 3.3 V and IOUT = 1A) HSON8-P-0505-1.27 Weight: 0.068 g (typ.) • Operating voltage range: VIN = 4.5 to 20 V • Low ON-resistance: RDS (ON) = 0.18 Ω (high-side) typical (@VIN = 12 V, Tj = 25°C) • Oscillation frequency: fOSC = 380 kHz (typ.) • Reference voltage: VFB = 0.8 V ±2.25%(@ Tj = 25 ℃) • Because of an external phase compensation element, the optimal phase compensation according to the output filter capacitor can be realized. • Allows the use of a small surface-mount ceramic capacitor as an output filter capacitor. • Housed in a small surface-mount package (SOP Advance) with low thermal resistance. • Soft-start time adjustable by an external capacitor Part Marking Pin Assignment Part Number (or abbreviation code) TB 7106F EN COMP 8 7 6 VFB 5 Lot No. The dot (•) on the top surface indicates pin 1. *: SS 1 2 3 4 BOOT VIN LX GND The lot number consists of three digits. The first digit represents the last digit of the year of manufacture, and the following two digits indicates the week of manufacture between 01 and either 52 or 53. Manufacturing week code (The first week of the year is 01; the last week is 52 or 53.) Manufacturing year code (last digit of the year of manufacture) This product has a MOS structure and is sensitive to electrostatic discharge. Handle with care. The product(s) in this document (“Product”) contain functions intended to protect the Product from temporary small overloads such as minor short-term overcurrent, or overheating. The protective functions do not necessarily protect Product under all circumstances. When incorporating Product into your system, please design the system to avoid such overloads upon the Product, and to shut down or otherwise relieve the Product of such overload conditions immediately upon occurrence. For details, please refer to the notes appearing below in this document and other documents referenced in this document. Start of commercial production 1 2010-07 2013-11-01 TB7106F Ordering Information Part Number Shipping TB7106F (TE12L, Q) Embossed tape (3000 units per reel) Block Diagram VIN Regulator Current detection Under voltage lockout Constant-current source (5μA) Error Amplifier VFB EN BOOT Driver LX Ground + Soft Start - Control Logic - SS + Slope Compensation Oscillator Short-Circuit Protection Ref.Voltage (0.8V) GND COMP Pin Description Pin No. Symbol 1 BOOT 2 VIN 3 LX 4 GND 5 VFB 6 COMP Description Bootstrap pin This pin is connected to Bootstrap capacitor. A 0.1μF bootstrap capacitor is required between BOOT pin and LX pin. Input pin This pin is placed in the standby state if VEN=”L”. Standby current is 60 μA (@VIN=12V) or less. Switch pin This pin is connected to high-side N-channel MOSFET. Ground pin Feedback pin This input is fed into an internal error amplifier with a reference voltage of 0.8 V (typ.). Phase compensation pin Pin for connecting an error amplifier phase compensation resistor and capacitor. Enable pin 7 EN When VEN ≥ 1.8 V (@ VIN = 12 V), the internal circuitry is allowed to operate and thus enable the switching operation of the output section. When VEN ≤ 0.5 V (@ VIN =12 V), the internal circuitry is disabled, putting the TB7106F in Standby mode. This pin has an internal pull-up current of 15 µA(typ.). Soft-start pin 8 SS When the SS input is left open, the soft-start time is 1 ms (typ.). The soft-start time can be adjusted with an external capacitor. The external capacitor is charged from a 5μA (typ.) constant-current source, and the reference voltage of the error amplifier is regulated between 0 V and 0.8 V. The external capacitor is discharged when VEN=”L” and in case of undervoltage lockout or thermal shutdown. 2 2013-11-01 TB7106F Absolute Maximum Ratings (Ta = 25°C) Characteristics Symbol Rating Unit VIN -0.3～25 V VBOOT -0.3～28 V VBOOT - VLX -0.3～6 V VLX -0.3～25 V Feedback pin voltage VFB -0.3～6 V Enable pin voltage VEN -0.3～25 V Soft-start pin voltage Vss -0.3～6 V VCOMP -0.3～6 V ILX -3.6 A PD 2.2 W Tjopr -40～125 ℃ Tj 150 °C Tstg -55～150 °C Input pin voltage Bootstrap pin voltage Bootstrap pin - Switch pin voltage Switch pin voltage (Note1) Error amplifier phase compensation pin voltage Switch pin current Power dissipation (Note 2) Operating junction temperature Junction temperature (Note 3) Strage temperature Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc) Note 1: The switch pin voltage (VLX) doesn’t include the peak voltage generated by TB7106F’s switching. Thermal Resistance Characteristics Characteristics Symbol Max Unit Thermal resistance, junction to ambient Rth (j-a) 44.6(Note2) °C/W Thermal resistance, junction to case (Tc=25℃) Rth (j-c) 4.17 °C/W Note 2: Glass epoxy board Material: FR-4 25.4 × 25.4 × 0.8 (Unit: mm) Single-pulse measurement: pulse width t=10(s) Note 3: The TB7106F may go into thermal shutdown at the rated maximum junction temperature. Thermal design is required to ensure that the rated maximum operating junction temperature, Tjopr, will not be exceeded. 3 2013-11-01 TB7106F Electrical Characteristics (Tj = 25°C, VIN = 4.5 to 20 V, unless otherwise specified) Characteristics Operating input voltage Input current Symbol Test Condition Min Typ. Max Unit VIN(OPR) ⎯ 4.5 ⎯ 20 V ⎯ 1.8 2.5 mA 0.8 ⎯ VIN -2 V ⎯ ⎯ 60 μA ⎯ ⎯ 10 μA IIN Output voltage range VIN = 12V ,VEN = 5V ,VFB = 2 V VOUT(OPR) VEN = VIN Standby current IIN(STBY) High-side switch leakage current ILEAK(H) VIN = 12 V , VEN = 0 V VFB = 0.8 V VIN = 12 V, VEN = 0 V VFB = 0.8 V , VLX = 0 V VIH(EN) VIN = 12 V 1.8 ⎯ ⎯ VIL(EN) VIN = 12V ⎯ ⎯ 0.5 IIH(EN) VIN = 12V, VEN = 5 V -5 ⎯ 5 IIL(EN) VIN = 12V, VEN = 0 V ⎯ -15 ⎯ VFB input voltage VFB VIN = 12 V , VEN = 5 V 0.782 0.8 0.818 V VFB input current IFB -1 ⎯ 1 μA ⎯ -18 ⎯ EN threshold voltage EN input current Error amplifier phase compensation input current ICOMP(H) ICOMP(L) High-side switch on-state resistance RDS(ON)(H) Low-side switch on-state resistance RDS(ON)(L) VIN = 12 V , VEN = 5 V VFB = 2V VIN = 12 V , VEN = 5 V VFB = 0.7V , VCOMP = 0.5 V VIN = 12 V , VEN = 5 V VFB = 0.9V , VCOMP = 0.5 V VIN = 12V , VEN = 5V ILX = - 1A VIN = 12 V , VEN =5 V ILX = 100m A VIN = 12V , VEN= 5V V μA μA ⎯ 18 ⎯ ⎯ 0.18 ⎯ Ω ⎯ 1.5 ⎯ Ω 300 380 460 kHz Oscillation frequency fOSC Internal soft-start time tSS Measured between 0% and 90% points at VOUT 0.5 1 2 ms External soft-start charge current ISS VIN = 12 V , VEN = 5 V -3 -5 -8 μA Dmax VIN = 12 V , VEN = 5 V ⎯ 88 ⎯ % Detection temperature TSD VIN = 12 V , VEN = 5 V ⎯ 160 ⎯ Hysteresis ΔTSD VIN = 12 V , VEN = 5 V ⎯ 15 ⎯ Detection voltage VUV VEN = VIN 2.9 3.2 3.5 VEN = VIN 3.2 3.5 3.8 VEN = VIN ⎯ 0.3 ⎯ 3.4 4.5 ⎯ VIN = 12 V , VEN= 5V , IOUT = 0A High-side switch duty cycle Thermal shutdown (TSD) Undervoltage lockout (UVLO) LX current limit Recovery voltage VUVR Hysteresis ΔVUV ILIM VIN = 12V , VEN= 5V VOUT = 2 V 4 °C V A 2013-11-01 TB7106F Note on Electrical Characteristics The test condition Tj = 25°C means a state where any drifts in electrical characteristics incurred by an increase in the chip’s junction temperature can be ignored during pulse testing. Application Circuit Example Figure1 shows a typical application circuit using a low-ESR electrolytic or ceramic capacitor for COUT. VIN=4.5V to 20V VIN EN BOOT EN LX COMP CIN RP TB7106F SS GND RFB1 VFB GND CP VOUT L CBOOT COUT RFB2 SBD CSS GND Figure 1 TB7106F Application Circuit Example Component values (reference value@ VIN = 12 V, VOUT = 3.3 V, Ta = 25°C) CIN: Input filter capacitor = 10 μF (ceramic capacitor: GRM31CR71E106K manufactured by Murata Manufacturing Co., Ltd.) COUT: Output filter capacitor = 22 μF×2 (ceramic capacitor: GRM31CB31C226ME15L manufactured by Murata Manufacturing Co., Ltd.) RFB1: Output voltage setting resistor = 7.5 kΩ RFB2: Output voltage setting resistor = 2.4 kΩ CP: Phase compensation capacitance RP: Phase compensation resistance L: Inductor = 10 μH (SLF10165T-100M3R83PF manufactured by TDK-EPC Corporation or DG8040C 1267AY-100M manufactured by TOKO, INC) SBD : Schottky barrier diode CRS30I30A (manufactured by Toshiba Co., Ltd. ) CBOOT: Bootstrap capacitor = 0.1 μF (GRM188R71H104J manufactured by Murata Manufacturing Co., Ltd.) CSS is a capacitor for adjusting the soft-start time. Examples of Component Values (For Reference Only) RFB2 Phase Compensation Capacitance CP Phase Compensation Resistance RP 7.5 kΩ 15 kΩ 4700pF 10 kΩ 44 μF 16 kΩ 18 kΩ 4700pF 12 kΩ 10 μF 44 μF 15 kΩ 12 kΩ 2200pF 15 kΩ 10 μH 10 μF 44 μF 5.1 kΩ 2.4 kΩ 2200pF 22 kΩ 3.3 V 10 μH 10 μF 44 μF 7.5 kΩ 2.4 kΩ 2200pF 27 kΩ 5.0V 10 μH 10 μF 44 μF 27 kΩ 5.1 kΩ 2200pF 33 kΩ Output Voltage Setting Inductance Input Capacitance Output Capacitance Feedback Resistor Feedback Resistor VOUT L CIN COUT RFB1 1.2 V 6.8 μH 10 μF 44 μF 1.51 V 6.8 μH 10 μF 1.8 V 6.8 μH 2.5 V Component values need to be adjusted, depending on the TB7106F’s I/O conditions and the board layout. 5 2013-11-01 TB7106F Application Notes Inductor Selection The inductance required for inductor L can be calculated as follows: VIN: Input voltage (V) VIN − VOUT VOUT VOUT: Output voltage (V) ············· (1) L= ⋅ fOSC ⋅ ΔIL VIN fOSC: Oscillation frequency = 380 kHz (typ.) ΔIL: Inductor ripple current (A) *: Generally, ΔIL should be set to approximately 30% of the maximum output current. Since the maximum output current of the TB7106F is 3.0 A, ΔIL should be 0.9 A or so. The inductor should have a current rating greater than the peak output current of 3.5 A. If the inductor current rating is exceeded, the inductor becomes saturated, leading to an unstable DC-DC converter operation. L= = VIN − VOUT VOUT ⋅ fOSC ⋅ ΔIL VIN 12 V − 3.3 V 3.3 V ⋅ 380kHz ⋅ 0.9A 12 V ΔIL When VIN = 12 V and VOUT = 3.3 V, the required inductance can be calculated as follows. Be sure to select an appropriate inductor, taking the input voltage range into account. IL 0 T= = 7.0μH 1 fosc V TON = Τ ⋅ OUT VIN Figure 2 Inductor Current Waveform Setting the Output Voltage A resistive voltage divider is connected as shown in Figure 3 to set the output voltage; it is given by Equation 2 based on the reference voltage of the error amplifier (0.8 V typ.), which is connected to the Feedback pin, VFB. RFB1 should be up to 30 kΩ or so, because an extremely large-value RFB1 incurs a delay due to parasitic capacitance at the VFB pin. It is recommended that resistors with a precision of ±1% or higher be used for RFB1 and RFB2. LX VFB VOUT RFB2 RFB1 ⎛ ⎞ R VOUT = VFB ⋅ ⎜⎜ 1 + FB1 ⎟⎟ R FB2 ⎠ ⎝ ⎛ R ⎞ = 0.8 V ⋅ ⎜⎜1 + FB1 ⎟⎟ ········ (2) ⎝ R FB2 ⎠ Figure 3 Output Voltage Setting Resistors Setting the Phase Compensation Circuit Connect a resister (RP) in series with a capacitor (CP) to COMP pin as a phase compensation. The following calculated value provides an estimation of the constant of phase compensation. F0=Frequency in loop gain being 0dB ：Set approximately to one-tenth of the switching frequency Fz=Frequency of pole-zero ：Set approximately to one-tenth of the F0 1 1 Fz = ⋅ Design value (reference): 2π Cp ⋅ Rp Gm(EA)=Error Amp Gm：200(μS) Gm(IS)=Current detection circuit Gm：7(S) The optimum value of phase compensation may change with the characteristics of COUT and another. If it use on the low temperature and the low output voltage conditions, switching waves becomes unstable and the output voltage ripple might increase. At this time, when the value of the output filter capacitor is enlarged, it is likely to be improved. Carry out sufficient evaluation on an actual operating condition. R FB2 1 Gm(IS) F0 = ⋅ ⋅ Gm(EA)Rp ⋅ 2π R FB1 + R FB2 C OUT 6 2013-11-01 TB7106F Output Filter Capacitor Selection Use a low-ESR electrolytic or ceramic capacitor as the output filter capacitor. Since a capacitor is generally sensitive to temperature, choose one with excellent temperature characteristics. The large capacitance improves load response characteristics. The capacitance should be set to an optimal value that meets the system’s ripple voltage requirement and transient load response characteristics. Since the ceramic capacitor has a very low ESR value, it helps reduce the output ripple voltage; however, because the ceramic capacitor provides less phase margin, it should be thoroughly evaluated. Rectifier Selection A Schottky barrier diode should be externally connected to the TB7106F as a rectifier between the LX and GND pins. It is recommended that either CRS30I30A, be used as the Schottky barrier diode. If a large voltage overshoot is on the LX pin, it reduces the voltage to connect a series CR network consisting of a resistor of RS = 4.7 Ω and a capacitor of CS = 470 pF with the Schottky barrier diode in parallel. Power loss of the Schottky barrier diode tends to increase due to an increased reverse current caused by the rise in ambient temperature and self-heating due to a supplied current. The rated current should therefore be derated to allow for such conditions in selecting an appropriate diode. Soft-Start Feature The TB7106F has a soft-start feature. If the SS pin is left open, the soft-start time, tSS, for VOUT defaults to 1 ms (typ.) internally. The soft-start time can be extended by adding an external capacitor (CSS) between the SS and GND pins. The soft-start time can be calculated as follows: t SS2 = 0.16 ⋅ CSS ·························· (3) tSS2: Soft-start time (in seconds) when an external capacitor is connected between SS and GND. CSS: Capacitor value (μF) The soft-start feature is activated when the TB7106F exits the undervoltage lockout (UVLO) state after power-up and when the voltage at the EN pin has changed from logic low to logic high. Overcurrent Protection（OCP） The TB7106F has built-in maximum current limiting with pulse skip. When the peak current of LX pin exceeds ILIM=4.5A(typ.) ＠VIN = 12V, the ON time of the high-side switch(internal) will be limited. Switching frequency will be reduced and output current will be restricted further if output voltage falls and the voltage of VFB pin drops below the overcurrent pulse skip detection voltage VLOC (0.3V typ.) during overcurrent protection . When VIN≧6.5V, The TB7106F can operate at IOUT = 3.0A(max). Meanwhile, use it at IOUT = 2.5A(max) when VIN＜6.5V. Undervoltage Lockout (UVLO) The TB7106F has undervoltage lockout (UVLO) protection circuitry. The TB7106F does not provide output voltage (VOUT) until the input voltage has reached VUVR (3.5 V typ.). UVLO has hysteresis of 0.3 V (typ.). After the switch turns on, if VIN drops below VUV (3.2 V typ.), UVLO shuts off the switch at VOUT. Undervoltage lockout recovery voltage VUVR VIN Undervoltage lockout detection voltage VUV Hysteresis: ΔVUV GND Switching operation starts VOUT GND Switching operation stops Soft start Figure 4 Undervoltage Lockout Operation 7 2013-11-01 TB7106F Thermal Shutdown (TSD) The TB7106F provides thermal shutdown. When the junction temperature continues to rise and reaches TSD (160°C typ.), the TB7106F goes into thermal shutdown and shuts off the power supply. TSD has a hysteresis of about 15°C (typ.). The device is enabled again when the junction temperature has dropped by approximately 15°C from the TSD trip point. The device resumes the power supply when the soft-start circuit is activated upon recovery from TSD state. Thermal shutdown is intended to protect the device against abnormal system conditions. It should be ensured that the TSD circuit will not be activated during normal operation of the system. TSD detection temperature: TSD Recovery from TSD Hysteresis: ΔTSD Tj 0 Switching operation starts VOUT GND Switching operation stops Soft start Figure 5 Thermal Shutdown Operation Area of Safety Operation The TB7106F limits the output current according to the duty cycle of the high side switch. IOUT in the area of safety operation is a mean value of direct current. Please note that it might cause the decrease in the output voltage and the decrease in the reliability of the product when this product is used on the condition to exceed the area of safety operation (Figure 6). IOUT – DUTY Maximum output current IOUT (A) 4 ３ Tj=100°C Tj=125°C 2 1 0 0 20 40 60 80 100 High-side switch duty cycle DUTY (%) Figure 6 Area of Safety Operation 8 2013-11-01 TB7106F Usage Precautions ・ The input voltage, output voltage, output current and temperature conditions should be considered when selecting capacitors, inductors and resistors. These components should be evaluated on an actual system prototype for best selection. ・ Parts of this product in the surrounding are examples of the representative, and the supply might become impossible. Please confirm latest information when using it. ・ External components such as capacitors, inductors and resistors should be placed as close to the TB7106F as possible. ・ CIN should be connected as close to the GND and VIN pins as possible. Operation might become unstable due to board layout. ・ The minimum programmable output voltage is 0.8 V (typ.). If the difference between the input and output voltages is small, the output voltage might not be regulated accurately and fluctuate significantly. ・ GND pin is connected with the back of IC chip and serves as the heat radiation pin. Secure the area of a GND pattern as large as possible for greater of heat radiation. ・ The overcurrent protection circuits in the Product are designed to temporarily protect Product from minor overcurrent of brief duration. When the overcurrent protective function in the Product activates, immediately cease application of overcurrent to Product. Improper usage of Product, such as application of current to Product exceeding the absolute maximum ratings, could cause the overcurrent protection circuit not to operate properly and/or damage Product permanently even before the protection circuit starts to operate. ・ The thermal shutdown circuits in the Product are designed to temporarily protect Product from minor overheating of brief duration. When the overheating protective function in the Product activates, immediately correct the overheating situation. Improper usage of Product, such as the application of heat to Product exceeding the absolute maximum ratings, could cause the overheating protection circuit not to operate properly and/or damage Product permanently even before the protection circuit starts to operate. 9 2013-11-01 TB7106F Typical Performance Characteristics IIN – VIN IIN – Tj (mA) 4 3 IIN 2 IIN (mA) 2.5 Operating current Operating current 1.5 1 0.5 VEN = VFB = VIN Tj = 25°C 0 2 1 VEN = VIN = 12 V VFB = 0 V 0 0 5 10 15 Input voltage VIN 20 -50 -25 0 25 50 75 Junction temperature (V) IIN – Tj Tj (°C) VIH(EN), VIL(EN) – Tj (mA) VIN = 12 V EN threshold voltage VIH(EN), VIL(EN) (V) IIN 125 2 4 Operating current 100 3 2 1 1.5 VIH(EN) 1 VIL(EN) 0.5 VEN = VIN = 4.5 V VFB = 0 V 0 0 -50 -25 0 25 50 Junction temperature 75 100 Tj (°C) -50 125 -25 0 25 50 Junction temperature 75 Tj 100 125 (°C) IIH(EN) – VEN 80 VIN = 12 V Tj = 25°C EN input current IIH(EN) (μA) 60 40 20 0 -20 0 5 10 EN input voltage 15 VEN 20 (V) 10 2013-11-01 TB7106F VOUT – VIN VUV, VUVR – Tj 4 VEN = VIN VOUT = 3.3 V Tj = 25°C (V) 3.8 3 VOUT Recovery voltage VUVR 3.6 3.4 Output voltage Undervoltage lockout voltage VUV,VUVR (V) 4.0 Detection voltage VUV 3.2 3.0 2 1 VEN = VIN 2.8 -50 0 -25 0 25 50 75 Junction temperature Tj 100 125 2.5 Input voltage (°C) (V) VIN = 12 V VOUT = 1.2 V VEN = VIN VFB (V) VEN = VIN VOUT = 1.2 V Tj = 25°C (V) 0.82 Feedback pin voltage VFB Feedback pin voltage VIN 0.84 0.8 0.78 0.82 0.8 0.78 0.76 0 5 10 Input voltage 15 20 VIN -50 25 (V) -25 0 25 50 Junction temperature fOSC – VIN 75 Tj 100 125 (°C) fOSC – Tj 440 440 (kHz) 400 fOSC 400 Oscillation frequency (kHz) VIN = 12 V 420 fOSC Tj = 25°C 420 Oscillation frequency 4 VFB – Tj VFB – VIN 0.84 0.76 3.5 3 380 360 340 320 0 5 10 Input voltage 15 VIN 20 380 360 340 320 -50 25 (V) -25 0 25 50 Junction temperature 11 75 Tj 100 125 (°C) 2013-11-01 TB7106F ISS – VIN ISS – Tj 0 0 External soft-start charge current ISS (μA) External soft-start charge current ISS (μA) Tj = 25°C -2 -4 -6 -8 -10 0 5 10 15 Input voltage VIN 20 VIN = 12 V -2 -4 -6 -8 -10 -50 25 -25 0 25 50 75 Junction temperature (V) ISS – Tj 100 Tj 125 (°C) Overcurrent Protection 6 0 -2 (V) -4 VOUT Output voltage External soft-start charge current ISS (μA) VIN = 4.5 V -6 -8 -10 4 2 VIN = 12 V VOUT = 5 V L = 10μH Ta = 25°C 0 -50 -25 0 25 50 75 Junction temperature Tj 100 0 125 1 (°C) 4 5 IOUT 6 7 (A) 3 (V) VOUT 3 Output voltage VOUT (V) 3 Overcurrent Protection Overcurrent Protection 4 Output voltage 2 Output current 2 1 VIN = 12 V VOUT = 3.3 V L = 10μH, Ta = 25°C 0 0 1 2 3 2 1 VIN = 12 V VOUT = 2.5 V L = 10μH Ta = 25°C 0 4 Output current 5 IOUT 6 0 7 1 2 3 4 Output current (A) 12 5 IOUT 6 7 (A) 2013-11-01 TB7106F ΔVOUT – IOUT ΔVOUT – IOUT 100 VIN = 12 V , VOUT = 3.3 V L = 10 μH , COUT = 22 μF ×2 Ta = 25°C , LS :CRS30I30A (mV) VIN = 12 V , VOUT = 5 V L = 10 μH , COUT = 22 μF ×2 Ta = 25°C , LS :CRS30I30A 50 ΔVOUT 50 0 Output voltage Output voltage ΔVOUT (mV) 100 -50 -100 0 0.5 1 1.5 Output current 2 2.5 IOUT 0 -50 -100 3 0 0.5 (A) 1 IOUT 2.5 3 (A) η – IOUT 100 VIN = 12 V , VOUT = 2.5V L = 10 μH , COUT = 22 μF ×2 Ta = 25°C , LS :CRS30I30A 90 η (%) 50 0 Efficiency (mV) ΔVOUT 2 Output current ΔVOUT – IOUT 100 Output voltage 1.5 -50 80 70 VIN = 12 V VOUT = 5V L = 10 μH COUT = 22 μF ×2 Ta = 25°C LS :CRS30I30A 60 50 -100 0 0.5 1 1.5 Output current 2 2.5 IOUT 3 0 (A) 0.5 1 1.5 Output current η – IOUT 2 IOUT 2.5 3 (A) η – IOUT 100 90 90 VIN = 12 V VOUT = 3.3 V L = 10 μH COUT = 22 μF ×2 Ta = 25°C LS :CRS30I30A 60 η 70 80 Efficiency η 80 Efficiency (%) (%) 100 70 VIN = 12 V VOUT = 2.5V L = 10 μH COUT = 22 μF ×2 Ta = 25°C LS :CRS30I30A 60 50 50 0 0.5 1 1.5 Output current 2 IOUT 2.5 3 0 (A) 0.5 1 1.5 Output current 13 2 IOUT 2.5 3 (A) 2013-11-01 TB7106F Startup Characteristics (Internal Soft-Start Time) VIN = 12 V VOUT = 3.3 V Ta = 25°C L = 10μH COUT = 22 μF ×2 Startup Characteristics (CSS = 0.1 μF) VIN = 12V VOUT = 3.3 V Ta = 25°C L = 10 μH COUT = 22 μF ×2 Output voltage: VOUT (1V/div) Output voltage: VOUT (1V/div) EN input voltage: VEN:L→H EN input voltage: VEN:L→H 200 μs/div 4 ms/div Load Response Characteristics Load Response Characteristics VIN = 12V , VOUT = 3.3 V , Ta = 25°C L = 10 μH , COUT = 22μF ×2 VIN = 12 V , VOUT = 1.2 V , Ta = 25°C L = 6.8μH , COUT = 22 μF ×2 Output voltage: VOUT (100 mV/div) Output voltage: VOUT (200 mV/div) Output current: IOUT: (1.5A→3A→1.5A) Output current: IOUT (10mA→3A→10mA) 200 μs/div 200 μs/div 14 2013-11-01 TB7106F Package Dimensions HSON8-P-0505-1.27 Unit: mm Weight: 0.068 g (typ.) 15 2013-11-01 TB7106F RESTRICTIONS ON PRODUCT USE • Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. • This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. • Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. • PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT ("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales representative. • Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. • Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. • ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. • Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. • Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS. 16 2013-11-01