TC4015BF

TC4015BP/BF/BFN TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC4015BP,TC4015BF,TC4015BFN TC4015B Dual 4-Stage Static Shift Register (with serial input/parallel output) TC4015B contains two circuits of 4 stage shift registers and the independent output is drived from each stage. As all the D type flip-flops of every stage have common RESET input, asynchronous clear operation can be achieved by an external signal at arbitrary timing. The flip-flop of each stage is triggered by rising edge of CLOCK input. RESET input of “H” level resets the contents of all the stages to “L” regardless of CLOCK and DATA inputs and all of data outputs Q1 through Q4 become “L”. This can be used for converting serial data to palallel one and for ring counters of any numbering systems. Note: xxxFN (JEDEC SOP) is not available in Japan. TC4015BP TC4015BF Pin Assignment TC4015BFN Truth Table Inputs CLOCKΔ DATA L H * * * RESET L L L H L Q1 L H Outputs Q2 Q1 Q1 Q3 Q2 Q2 Q4 Q3 Q3 Weight DIP16-P-300-2.54A SOP16-P-300-1.27A SOL16-P-150-1.27 : 1.00 g (typ.) : 0.18 g (typ.) : 0.13 g (typ.) No Change L L L Δ: Level change *: Don’t care 1 2007-10-01 TC4015BP/BF/BFN Logic Diagram 1/2 TC4015B Absolute Maximum Ratings (Note) Characteristics DC supply voltage Input voltage Output voltage DC input current Power dissipation Operating temperature range Storage temperature range Symbol VDD VIN VOUT IIN PD Topr Tstg Rating VSS − 0.5~VSS + 20 VSS − 0.5~VDD + 0.5 VSS − 0.5~VDD + 0.5 ±10 300 (DIP)/180 (SOIC) −40~85 −65~150 Unit V V V mA mW °C °C Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Operating Ranges (VSS = 0 V) (Note) Characteristics DC supply voltage Input voltage Symbol VDD VIN Test Condition ⎯ ⎯ Min 3 0 Typ. ⎯ ⎯ Max 18 VDD Unit V V Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VDD or VSS. 2 2007-10-01 TC4015BP/BF/BFN Static Electrical Characteristics (VSS = 0 V) Characteristics Symbol Test Condition VDD (V) ⎪IOUT⎪ < 1 μA VIN = VSS, VDD ⎪IOUT⎪ < 1 μA VIN = VSS, VDD VOH = 4.6 V VOH = 2.5 V Output high current IOH VOH = 9.5 V VOH = 13.5 V VIN = VSS, VDD VOL = 0.4 V Output low current IOL VOL = 0.5 V VOL = 1.5 V VIN = VSS, VDD VOUT = 0.5 V, 4.5 V Input high voltage VIH VOUT = 1.0 V, 9.0 V VOUT = 1.5 V, 13.5 V ⎪IOUT⎪ < 1 μA VOUT = 0.5 V, 4.5 V Input low voltage VIL VOUT = 1.0 V, 9.0 V VOUT = 1.5 V, 13.5 V ⎪IOUT⎪ < 1 μA Input current “H” level “L” level IIH IIL VIH = 18 V VIL = 0 V VIN = VSS, VDD (Note) 18 18 5 10 15 ⎯ ⎯ ⎯ ⎯ ⎯ 0.1 −0.1 5 10 20 ⎯ ⎯ ⎯ ⎯ ⎯ 10− −10 5 −40°C Min 4.95 9.95 14.95 ⎯ ⎯ ⎯ −0.61 −2.50 −1.50 −4.00 Max ⎯ ⎯ ⎯ 0.05 0.05 0.05 ⎯ ⎯ ⎯ ⎯ Min 4.95 9.95 14.95 ⎯ ⎯ ⎯ −0.51 −2.10 −1.30 −3.40 25°C Typ. 5.00 10.00 15.00 0.00 0.00 0.00 −1.0 −4.0 −2.2 −9.0 Max ⎯ ⎯ ⎯ 0.05 0.05 0.05 ⎯ ⎯ ⎯ ⎯ Min 85°C Max ⎯ ⎯ ⎯ 0.05 0.05 0.05 ⎯ ⎯ ⎯ ⎯ mA V V Unit 5 10 15 5 10 15 5 5 10 15 4.95 9.95 14.95 ⎯ ⎯ ⎯ −0.42 −1.70 −1.10 −2.80 High-level output voltage VOH Low-level output voltage VOL 5 10 15 0.61 1.50 4.00 ⎯ ⎯ ⎯ 0.51 1.30 3.40 1.2 3.2 12.0 ⎯ ⎯ ⎯ 0.42 1.10 2.80 ⎯ ⎯ ⎯ mA 5 10 15 3.5 7.0 11.0 ⎯ ⎯ ⎯ 3.5 7.0 11.0 2.75 5.50 8.25 ⎯ ⎯ ⎯ 3.5 7.0 11.0 ⎯ ⎯ ⎯ V 5 10 15 ⎯ ⎯ ⎯ 1.5 3.0 4.0 ⎯ ⎯ ⎯ 2.25 4.50 6.75 1.5 3.0 4.0 ⎯ ⎯ ⎯ 1.5 3.0 4.0 V 0.1 −0.1 5 10 20 ⎯ ⎯ ⎯ ⎯ ⎯ 1.0 −1.0 150 300 600 −5 μA 0.005 0.010 0.015 Quiescent supply current IDD μA Note: All valid input combinations. 3 2007-10-01 TC4015BP/BF/BFN Dynamic Electrical Characteristics (Ta = 25°C, VSS = 0 V, CL = 50 pF) Characteristics Symbol Test Condition VDD (V) 5 tTLH ⎯ 10 15 5 tTHL ⎯ 10 15 tpLH tpHL 5 ⎯ 10 15 5 tpHL ⎯ 10 15 5 Max clock frequency fCL ⎯ 10 15 5 Min clock pulse width tW ⎯ 10 15 Min pulse width (RESET) 5 tWH ⎯ 10 15 5 tSU ⎯ 10 15 5 tH ⎯ 10 15 5 trem ⎯ 10 15 trCL tfCL CIN 5 ⎯ 10 15 ⎯ ⎯ 5 7.5 pF No limit μs Min ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 3.0 6.0 8.5 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Typ. 70 35 30 70 35 30 130 60 50 90 45 40 8 17 20 35 25 20 50 25 20 8 4 0 6 5 4 0 0 0 Max 200 100 80 200 100 80 320 160 120 400 200 160 ⎯ ⎯ ⎯ 180 80 50 200 80 60 70 40 30 60 30 20 80 30 20 ns ns ns ns ns MHz ns ns ns ns Unit Output transition time (low to high) Output transition time (high to low) Propagation delay time (CLOCK-Q) Propagation delay time (RESET-Q) Min set-up time (DATA-CLOCK) Min hold time (DATA-CLOCK) Min removal time (RESET-CLOCK) Max clock input rise time Max clock input fall time Input capacitance 4 2007-10-01 TC4015BP/BF/BFN Waveforms for Measurement of Dynamic Characteristics Waveform 1 Waveform 2 Waveform 3 5 2007-10-01 TC4015BP/BF/BFN Package Dimensions Weight: 1.00 g (typ.) 6 2007-10-01 TC4015BP/BF/BFN Package Dimensions Weight: 0.18 g (typ.) 7 2007-10-01 TC4015BP/BF/BFN Package Dimensions (Note) Note: This package is not available in Japan. Weight: 0.13 g (typ.) 8 2007-10-01 TC4015BP/BF/BFN RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN GENERAL • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 9 2007-10-01