TC4052BFT

TC4051,4052,4053BP/BF/BFN/BFT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC4051BP, TC4051BF, TC4051BFN, TC4051BFT TC4052BP, TC4052BF, TC4052BFN, TC4052BFT TC4053BP, TC4053BF, TC4053BFN, TC4053BFT TC4051B Single 8-Channel Multiplexer/Demultiplexer TC4052B Differential 4-Channel Multiplexer/Demultiplexer TC4053B Triple 2-Channel Multiplexer/Demultiplexer TC4051B, TC4052B and TC4053B are multiplexers with capabilities of selection and mixture of analog signal and digital signal. TC4051B has 8 channels configuration. TC4052B has 4 channel × 2 configuration and TC4053B has 2 channel × 3 configuration. The digital signal to the control terminal turns “ON” the corresponding switch of each channel, with large amplitude (VDD − VEE) can be switched by the control signal with small logical amplitude (VDD − VSS). For example, in the case of VDD = 5 V VSS = 0 V and VEE = −5 V, signals between −5 V and +5 V can be switched from the logical circuit with single power supply of 5 volts. As the ON-resistance of each switch is low, these can be connected to the circuits with low input impedance. Note: xxxFN (JEDEC SOP) is not available in Japan. TC4051BP, TC4052BP, TC4053BP TC4051BF, TC4052BF, TC4053BF TC4051BFN, TC4052BFN, TC4053BFN TC4051BFT, TC4052BFT, TC4053BFT Weight DIP16-P-300-2.54A SOP16-P-300-1.27A SOL16-P-150-1.27 TSSOP16-P-0044-0.65A : 1.00 g (typ.) : 0.18 g (typ.) : 0.13 g (typ.) : 0.06 g (typ.) 1 2007-10-01 TC4051,4052,4053BP/BF/BFN/BFT Pin Assignment TC4051B 4 6 COM 7 5 INH VEE VSS 1 2 3 4 5 6 7 8 (top view) 16 15 14 13 12 11 10 9 VDD 2 1 0 3 A B C 0Y 2Y Y-COM 3Y 1Y INH VEE VSS 1 2 3 4 5 6 7 8 (top view) TC4052B 16 15 14 13 12 11 10 9 VDD 2X 1X X-COM 0X 3X A B TC4053B 1Y 0Y 1Z Z-COM 0Z INH VEE VSS 1 2 3 4 5 6 7 8 (top view) 16 15 14 13 12 11 10 9 VDD Y-COM X-COM 1X 0X A B C Truth Table Control Inputs Inhibit L L L L L L L L H CΔ L L L L H H H H X B L L H H L L H H X A L H L H L H L H X TC4051B 0 1 2 3 4 5 6 7 None “ON” Channel TC4052B 0X, 0Y 1X, 1Y 2X, 2Y 3X, 3Y ⎯ ⎯ ⎯ ⎯ None TC4053B 0X, 0Y, 0Z 1X, 0Y, 0Z 0X, 1Y, 0Z 1X, 1Y, 0Z 0X, 0Y, 1Z 1X, 0Y, 1Z 0X, 1Y, 1Z 1X, 1Y, 1Z None X: Don’t care Δ: Except TC4052B 2 2007-10-01 TC4051,4052,4053BP/BF/BFN/BFT Logic Diagram TC4051B VDD 16 OUT c A 11 Logic Level Converter OUT c OUT c OUT c OUT c OUT c OUT c OUT c 8 VSS IN IN IN IN IN IN IN IN 0 1 2 3 4 5 6 7 COMMON 13 14 15 12 1 5 2 4 3 B 10 C 9 INH 6 7 VEE TC4052B VDD 16 OUT c OUT c A 10 Logic Level Converter OUT c OUT c OUT c OUT c OUT c OUT c 8 VSS 7 VEE IN IN IN IN IN IN IN IN 13 12 14 15 11 1 5 2 4 3 X-COMMON 0X 1X 2X 3X 0Y 1Y 2Y 3Y Y-COMMON B 9 INH 6 3 2007-10-01 TC4051,4052,4053BP/BF/BFN/BFT TC4053B VDD 16 14 A OUT c 11 Logic Level Converter OUT c OUT c OUT c OUT c OUT c IN IN IN IN IN IN 12 13 2 1 5 3 4 8 VSS 15 7 VEE X-COMMON 0X 1X 0Y 1Y 0Z 1Z Z-COMMON Y-COMMON B 10 C 9 INH 6 Truth Table Control C H L Impedance between IN-OUT 0.5 to 5 × 10 Ω >10 Ω 9 2 (Note) Note: See electrical characteristics OUT c IN Absolute Maximum Ratings (Note) Characteristics DC supply voltage DC supply voltage Control input voltage Switch I/O voltage Control input current Potential difference across I/O during ON Power dissipation Operating temperature range Storage temperature range Symbol VDD-VSS VDD-VEE VCIN VI/VO ICIN VI-VO PD Topr Tstg Rating −0.5 to 20 −0.5 to 20 VSS − 0.5 to VDD + 0.5 VEE − 0.5 to VDD + 0.5 ±10 −0.5 to 0.5 300 (DIP)/180 (SOIC) −40 to 85 −65 to 150 Unit V V V V mA V mW °C °C Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). 4 2007-10-01 TC4051,4052,4053BP/BF/BFN/BFT Operating Ranges (Note) Characteristics DC supply voltage Control input voltage Input/output voltage Symbol VDD-VSS VDD-VEE VIN VIN/VOUT Test Condition ⎯ ⎯ ⎯ ⎯ Min 3 3 VSS VEE Typ. ⎯ ⎯ ⎯ ⎯ Max 18 18 VDD VDD Unit V V V Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused Control inputs must be tied to either VDD or VSS. Static Electrical Characteristics Test Condition Characteristics Symbol VSS (V) VEE VDD (V) (V) 5 10 15 5 10 15 On-state resistance ΔOn-state resistance between any 2 switches Input/output leakage current 0 ≤ VIS ≤ VDD RL = 10 kΩ 0 0 0 0 RONΔ ⎯ 0 0 IOFF VIN = 18 V, VOUT = 0 V VIN = 0 V, VOUT = 18 V VIN = VSS, VDD VIH = 18 V VIL = 0 V ⎯ ⎯ TC4051B Output capacitance COUT TC4052B TC4053B TC4051B Feedthrough capacitance CINC-OUT TC4052B TC4053B 0 0 0 0 0 0 5 10 15 5 10 15 18 18 5 Quiescent supply current IDD (Note) 10 15 Input current Input capacitance Switch input capacitance IIN CIN CIN 18 18 ⎯ ⎯ 10 10 10 10 10 10 −40°C Min 3.5 7.0 11.0 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Max ⎯ ⎯ ⎯ 1.5 3.0 4.0 850 210 140 ⎯ ⎯ ⎯ ±100 ±100 5.0 10 20 0.1 −0.1 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min 3.5 7.0 11.0 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 25°C Typ. 2.75 5.50 8.25 2.25 4.5 6.75 240 110 80 10 6 4 ±0.01 ±0.01 0.005 0.010 0.015 10 −5 −5 85°C Max ⎯ ⎯ ⎯ 1.5 3.0 4.0 950 250 160 ⎯ ⎯ ⎯ ±100 ±100 5.0 10 20 0.1 −0.1 7.5 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min 3.5 7.0 11.0 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Max ⎯ ⎯ ⎯ 1.5 3.0 4.0 1200 300 200 ⎯ ⎯ ⎯ ±1000 ±1000 150 300 600 1.0 −1.0 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ pF pF μA pF pF μA nA Ω Ω V V Unit Control input high voltage VIH VIS = VDD thru 1 kΩ VEE = VSS RL = 1 kΩ to VSS IIS < 2 μA on all OFF channels Control input low voltage VIL RON −10 5 10 58 30 17 0.2 0.2 0.2 Note: All valid input combinations. 5 2007-10-01 TC4051,4052,4053BP/BF/BFN/BFT Dynamic Electrical Characteristics (Ta = 25°C, CL = 50 pF) Test Condition Characteristics Symbol VSS (V) 0 Phase difference between input to output φI-O ⎯ 0 0 tpZL Propagation delay time (A, B, C, -OUT) tpZH tpLZ tpHZ RL = 1 kΩ 0 0 0 0 0 0 Propagation delay time (INH-OUT) tpZL tpZH 0 RL = 1 kΩ 0 0 0 0 Propagation delay time (INH-OUT) tpLZ tpHZ 0 RL = 1 kΩ 0 0 0 −3dB cutoff frequency TC4051B TC4052B TC4053B RL = 10 kΩ f = 1 kHz (Note 2) fmax (I-O) RL = 1 k Ω (Note 1) −5 −5 −5 VEE VDD (V) (V) 0 0 0 0 0 0 −5 −7.5 0 0 0 −5 −7.5 0 0 0 −5 −7.5 −5 −5 −5 5 10 15 5 10 15 5 7.5 5 10 15 5 7.5 5 10 15 5 7.5 5 5 5 2.5 5 7.5 5 5 5 10 15 Min ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Typ. 15 8 6 170 90 70 100 80 120 60 50 80 60 170 90 70 100 80 20 30 40 0.15 0.03 0.02 500 1.5 200 400 600 Max 45 20 15 550 240 160 240 160 380 200 160 200 160 450 210 160 210 160 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ mV kHz MHz % MHz ns ns ns ns Unit −2.5 −2.5 −5 −5 Total harmonic distortion ⎯ −7.5 −7.5 −5 −5 0 0 0 −5 −5 0 0 0 −50dB feedthrough (switch off) Crosstalk Crosstalk (control-OUT) ⎯ ⎯ RL = 1 kΩ RL = 1 kΩ RIN = 1 kΩ ROUT = 10 kΩ CL = 15 pF (Note 3) (Note 4) ⎯ Note 1: Sine wave of ±2.5 Vp-p shall be used for Vis and the frequency of 20 log 10 VOS = −3dB shall be fmax. Vis ⎛ V − VEE ⎞ Note 2: Vis shall be sine wave of ± ⎜ DD ⎟ p-p. 4 ⎝ ⎠ Note 3: Sine wave of ±2.5 Vp-p shall be used for Vis and the frequency of 20 log 10 feed-through. Note 4: Sine wave of ±2.5 Vp-p shall be used for Vis and the frequency of 20 log 10 crosstalk. VOS = −50dB shall be Vis VOS = −50dB shall be Vis 6 2007-10-01 TC4051,4052,4053BP/BF/BFN/BFT Package Dimensions Weight: 1.00 g (typ.) 7 2007-10-01 TC4051,4052,4053BP/BF/BFN/BFT Package Dimensions Weight: 0.18 g (typ.) 8 2007-10-01 TC4051,4052,4053BP/BF/BFN/BFT Package Dimensions (Note) Note: This package is not available in Japan. Weight: 0.13 g (typ.) 9 2007-10-01 TC4051,4052,4053BP/BF/BFN/BFT Package Dimensions Weight: 0.06 g (typ.) 10 2007-10-01 TC4051,4052,4053BP/BF/BFN/BFT RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 11 2007-10-01