TC4520BF

TC4520BP/BF/BFN TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC4520BP,TC4520BF,TC4520BFN TC4520B Dual Binary Up Counter TC4520B is up counters of 4 bit binary. Since both of TC4520B contain two independent circuits of counters with the same functions in one package, counting or frequency division of two BCD digits or eight binary bits can be achived with one IC. The counters can be reset to “0” (Q0~Q3 = “L”) by giving “H” level signal to RESET input regardless of other inputs. The counting condition is changed by the rising edge of CLOCK input if ENABLE = “H” or by the falling edge of ENABLE if CLOCK = “L”. Note: xxxFN (JEDEC SOP) is not available in Japan. TC4520BP Pin Assignment TC4520BF TC4520BFN Weight DIP16-P-300-2.54A SOP16-P-300-1.27A SOL16-P-150-1.27 : 1.00 g (typ.) : 0.18 g (typ.) : 0.13 g (typ.) 1 2007-10-01 TC4520BP/BF/BFN Logic Diagram Timing Chart 2 2007-10-01 TC4520BP/BF/BFN Absolute Maximum Ratings (Note) Characteristics DC supply voltage Input voltage Output voltage DC input current Power dissipation Operating temperature range Storage temperature range Symbol VDD VIN VOUT IIN PD Topr Tstg Rating VSS − 0.5~VSS + 20 VSS − 0.5~VDD + 0.5 VSS − 0.5~VDD + 0.5 ±10 300 (DIP)/180 (SOIC) −40~85 −65~150 Unit V V V mA mW °C °C Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Operating Ranges (VSS = 0 V) (Note) Characteristics DC supply voltage Input voltage Symbol VDD VIN Test Condition ⎯ ⎯ Min 3 0 Typ. ⎯ ⎯ Max 18 VDD Unit V V Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VDD or VSS. 3 2007-10-01 TC4520BP/BF/BFN Static Electrical Characteristics (VSS = 0 V) Characteristics Symbol Test Condition VDD (V) ⎪IOUT⎪ < 1 μA VIN = VSS, VDD ⎪IOUT⎪ < 1 μA VIN = VSS, VDD VOH = 4.6 V VOH = 2.5 V Output high current IOH VOH = 9.5 V VOH = 13.5 V VIN = VSS, VDD VOL = 0.4 V Output low current IOL VOL = 0.5 V VOL = 1.5 V VIN = VSS, VDD VOUT = 0.5 V, 4.5 V Input high voltage VIH VOUT = 1.0 V, 9.0 V VOUT = 1.5 V, 13.5 V ⎪IOUT⎪ < 1 μA VOUT = 0.5 V, 4.5 V Input low voltage VIL VOUT = 1.0 V, 9.0 V VOUT = 1.5 V, 13.5 V ⎪IOUT⎪ < 1 μA Input current “H” level “L” level IIH IIL VIH = 18 V VIL = 0 V VIN = VSS, VDD (Note) 18 18 5 10 15 ⎯ ⎯ ⎯ ⎯ ⎯ 0.1 −0.1 5 10 20 ⎯ ⎯ ⎯ ⎯ ⎯ 10− −10 5 −40°C Min 4.95 9.95 14.95 ⎯ ⎯ ⎯ −0.61 −2.5 −1.5 −4.0 Max ⎯ ⎯ ⎯ 0.05 0.05 0.05 ⎯ ⎯ ⎯ ⎯ Min 4.95 9.95 14.95 ⎯ ⎯ ⎯ −0.51 −2.1 −1.3 −3.4 25°C Typ. 5.00 10.00 15.00 0.00 0.00 0.00 −1.0 −4.0 −2.2 −9.0 Max ⎯ ⎯ ⎯ 0.05 0.05 0.05 ⎯ ⎯ ⎯ ⎯ Min 85°C Max ⎯ ⎯ ⎯ 0.05 0.05 0.05 ⎯ ⎯ ⎯ ⎯ mA V V Unit 5 10 15 5 10 15 5 5 10 15 4.95 9.95 14.95 ⎯ ⎯ ⎯ −0.42 −1.7 −1.1 −2.8 High-level output voltage VOH Low-level output voltage VOL 5 10 15 0.61 1.5 4.0 ⎯ ⎯ ⎯ 0.51 1.3 3.4 1.2 3.2 12.0 ⎯ ⎯ ⎯ 0.42 1.1 2.8 ⎯ ⎯ ⎯ mA 5 10 15 3.5 7.0 11.0 ⎯ ⎯ ⎯ 3.5 7.0 11.0 2.75 5.5 8.25 ⎯ ⎯ ⎯ 3.5 7.0 11.0 ⎯ ⎯ ⎯ V 5 10 15 ⎯ ⎯ ⎯ 1.5 3.0 4.0 ⎯ ⎯ ⎯ 2.25 4.5 6.75 1.5 3.0 4.0 ⎯ ⎯ ⎯ 1.5 3.0 4.0 V 0.1 −0.1 5 10 20 ⎯ ⎯ ⎯ ⎯ ⎯ 1.0 −1.0 150 300 600 −5 μA 0.005 0.010 0.015 Quiescent supply current IDD μA Note: All valid input combinations. 4 2007-10-01 TC4520BP/BF/BFN Dynamic Electrical Characteristics (Ta = 25°C, VSS = 0 V, CL = 50 pF) Characteristics Symbol Test Condition VDD (V) 5 tTLH ⎯ 10 15 5 tTHL ⎯ 10 15 tpLH tpHL 5 ⎯ 10 15 5 tpHL ⎯ 10 15 5 Max clock frequency tCL ⎯ 10 15 trCL tfCL 5 ⎯ 10 15 5 ⎯ 10 15 5 Min clock pulse width tW ⎯ 10 15 Min pulse width (ENABLE) 5 tW ⎯ 10 15 5 tWH ⎯ 10 15 5 trem ⎯ 10 15 CIN ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 30 15 10 35 20 15 45 20 15 ⎯ ⎯ ⎯ 5 200 100 70 250 110 80 250 110 80 0 0 0 7.5 pF ns ns ns ns No limit μs No limit μs Min ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 1.5 3 4 Typ. 70 35 30 70 35 30 160 75 60 110 55 40 6 14 18 Max 200 100 80 200 100 80 560 230 160 560 230 160 ⎯ ⎯ ⎯ MHz ns ns ns ns Unit Output transition time (low to high) Output transition time (high to low) Propagation delay time (CLOCK, ENABLE-Q) Propagation delay time (RESET-Q) Max clock input rise/fall time Max input rise/fall time (ENABLE) tr tf Min pulse width (RESET) Min removal time (RESET-CLOCK, ENABLE) Input capacitance 5 2007-10-01 TC4520BP/BF/BFN Waveforms for Measurement of Dynamic Characteristics Waveform 1 Waveform 2 6 2007-10-01 TC4520BP/BF/BFN Application Circuit (1) Ripple carry counter (2) Ripple carry counter 7 2007-10-01 TC4520BP/BF/BFN Package Dimensions Weight: 1.00 g (typ.) 8 2007-10-01 TC4520BP/BF/BFN Package Dimensions Weight: 0.18 g (typ.) 9 2007-10-01 TC4520BP/BF/BFN Package Dimensions (Note) Note: This package is not available in Japan. Weight: 0.13 g (typ.) 10 2007-10-01 TC4520BP/BF/BFN RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN GENERAL • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 11 2007-10-01