TC4W66FU
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC4W66FU
Dual Bilateral Switch
The TC4W66FU contains two independence circuits of
bidirectional switches.
When control input CONT is set to “H” level, the impedance
between input and output of the switch becomes low and when it
is set to “L” level, the switch becomes high. This can be applied
for switching of analog signals and digital signals.
Features
•
ON-resistance, RON
250 Ω (typ.) ................... VDD − VSS = 5 V
(SM8)
110 Ω (typ.) ................... VDD − VSS = 10 V
Weight
SSOP8-P-0.65 : 0.02 g (typ.)
70 Ω (typ.) ..................... VDD − VSS = 15 V
•
OFF-resistance, ROFF
ROFF (typ.) > 109 Ω
Absolute Maximum Ratings (Ta = 25°C)
Characteristics
Marking
Symbol
Rating
Unit
DC supply voltage
VDD
VSS − 0.5 to VSS + 20
V
Control input voltage
VC IN
VSS − 0.5 to VDD + 0.5
V
Switch I/O voltage
VI/O
VSS − 0.5 to VDD + 0.5
V
Power dissipation
PD
300
mW
Potential difference across I/O during
ON
VI-VO
±0.5
V
Control input current
IC IN
±10
mA
Operating temperature range
Topr
−40 to 85
°C
Storage temperature
Tstg
−65 to 150
°C
TL
260
°C
Lead temperature (10 s)
Type Name
4W66
Lot No.
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Start of commercial production
1989-12
1
2014-11-18
TC4W66FU
Pin Assignment (top view)
IN/OUT 1 1
8
OUT/IN 1 2
7 CONT 1
CONT 2 3
6 OUT/IN 2
VSS 4
5 IN/OUT 2
VDD
Truth Table
Control
Logic Diagram
Impedance Between IN/OUT-OUT/IN
(Note 1)
H
0.5 to 5 × 102 Ω
L
>109 Ω
I/O
O/I
CONT
Note 1: See static electrical characteristics.
Operating Ranges (VSS = 0 V)
Characteristics
Symbol
Test Condition
Min
Typ.
Max
Unit
DC supply voltage
VDD
3
18
V
Input/output voltage
VI/O
0
VDD
V
2
2014-11-18
TC4W66FU
Static Electrical Characteristics (VSS = 0 V)
Characteristics
Control input high
voltage
Control input low
voltage
On-state
resistance
Symbol
VIH
VIL
RON
∆On-state
resistance
(between any 2
switches)
RON∆
Input/output
leakage current
IOFF
Quiescent device
current
Control
input
current
H level
L level
IDD
IIH
IIL
Test Condition
IIS = 10 µA
IIS = 10 µA
0 ≤ VIS ≤ VDD
RL = 10 kΩ
Ta = −40°C
Ta = 25°C
Ta = 85°C
VDD
(V)
Min
Max
Min
Typ.
Max
Min
Max
5
3.5
3.5
2.75
3.5
10
7.0
7.0
5.50
7.0
15
11.0
11.0
8.25
11.0
5
1.5
2.25
1.5
1.5
10
3.0
4.5
3.0
3.0
15
4.0
6.75
4.0
4.0
5
800
290
950
1200
10
210
120
250
300
15
140
85
160
200
5
10
10
6
15
4
VIN = 18 V, VOUT = 0 V
18
±100
±0.1
±100
±1000
VIN = 0 V, VOUT = 18 V
18
±100
±0.1
±100
±1000
5
0.25
0.001
0.25
7.5
10
0.5
0.001
0.5
15
15
1.0
0.002
1.0
30
18
0.1
10−5
0.1
1.0
−0.1
−1.0
VIN = VDD, VSS
VIH = 18 V
VIL = 0 V
18
3
−0.1
−5
−10
Unit
V
V
Ω
Ω
nA
µA
µA
2014-11-18
TC4W66FU
Dynamic Electrical Characteristics (Ta = 25°C)
Characteristics
Phase difference between
input to output
Propagation delay time
(CONTROL-OUT)
Propagation delay time
(CONTROL-OUT)
Max control input repetition
Rate
Frequency Response
Symbol
φI-O
Test Condition
CL = 50 pF
tpZL
RL = 1 kΩ
tpZH
CL = 50 pF
tpLZ
RL = 1 kΩ
tpHZ
CL = 50 pF
fMAX
RL = 1 kΩ
(C)
CL = 50 pF
fMAX
RL = 1 kΩ
(I-O)
CL = 50 pF
Total harmonic distortion
Feed through frequency
(Switch OFF)
(Note 1)
RL = 10 kΩ
VSS
(V)
VDD
(V)
Min
Typ.
Max
Unit
0
5
15
40
0
10
8
20
0
15
5
15
0
5
55
120
0
10
25
40
0
15
20
30
0
5
45
80
0
10
30
70
0
15
25
60
0
5
10
0
10
12
0
15
12
−5
5
30
MHz
−5
5
0.03
%
ns
ns
ns
MHz
f = 1 kHz
(Note 2)
RL = 1 kΩ
(Note 3)
−5
5
600
kHz
Crosstalk frequency
RL = 1 kΩ
(Note 4)
−5
5
1
MHz
Crosstalk
(CONTROL-OUT)
Input capacitance
CIN
Feed through capacitance
RIN = 1 kΩ
0
5
200
ROUT = 10 kΩ
0
10
400
CL = 15 pF
0
15
600
Control input
5
7.5
Switch I/O
10
0.5
CIN-OUT
Note 1: Sine wave of ±2.5 Vp-p shall be used for VIS and the frequency of 20 ℓog 10
Note 2: VIS shall be sine wave of ±2.5 Vp-p.
Note 3: Sine wave of ±2.5 Vp-p shall be used for VIS and the frequency of 20 ℓog 10
feed-through.
Note 4: Sine wave of ±2.5 Vp-p shall be used for VIS and the frequency of 20 ℓog 10
crosstalk.
4
mV
pF
pF
VOS
= −3dB shall be fMAX.
VIS
VOUT
VIS
= −50dB shall be
VOUT
VIS
= −50dB shall be
2014-11-18
TC4W66FU
Circuit For Measurement of Electrical Characteristics
1.
tpLH, tpHL
I/O-O/I
tr =20 ns
VDD
tf =20 ns
90%
I/O
P.G.
O/I
50%
I/O IN
10%
tpLH
tpHL
50%
O/I OUT
2.
50%
10%
CL = 50 pF
C
VDD
90%
VSS
VOH
50%
VOL
tpZL, tpZH, tpLZ, tpHZ
CONTROL-O/I
tf =20 ns
tr =20 ns
VDD
90%
SW1
P.G.
I/O
O/I
RL = 1 kΩ
CL = 50 pF
C
SW2
CONTROL IN
50%
10%
tpZH
VSS
tpHZ
90%
VOH
50%
VOL
tpZL
O/IOUT.
SW1 = VSS
SW2 = VDD
3.
50%
10%
O/IOUT.
SW1 = VDD
SW2 = VSS
VDD
90%
tpLZ
VOH
50%
10%
VOL
RON
VDD
RON calculation method
VIN
I/O
O/I
VOUT
RON = 10 ×
RL = 10 kΩ
C
(VIN − VOUT ) (kΩ )
VOUT
VSS
5
2014-11-18
TC4W66FU
4.
fMAX (C)
VDD
tr =20 ns
tf =20 ns
90%
I/O
P.G.
50%
CONTROL
IN
O/I
10%
RL = 1 kΩ
CL = 50 pF
C
VDD
90%
50%
1
f
10%
VSS
VDD
2
O/IOUT
5.
Crosstalk frequency
(SWITCH ON)
VDD
2.5 V
P.G.
I/O
O/I
I/OIN
0V
RL = 1 kΩ
C
−2.5 V
VSS
(SWITCH OFF)
VDD
I/O
O/I
Crosstalk OUT
RL = 1 kΩ
C
VSS
6.
Crosstalk (Control input)
tr =20 ns
VDD
tf =20 ns
90%
I/O
P.G.
C
RL = 1 kΩ
O/I
CONTROL
IN
VOUT
10%
90%
10%
VDD
VSS
RL = 10 kΩ
CL = 15 pF
VOUT
6
2014-11-18
TC4W66FU
7.
Total Harmonic Distortion, fMAX (I/O-O/I), Feedthrough frequency(Switch OFF)
VDD
2.5 V
P.G.
I/O
O/I
I/OIN
0V
RL ,CL (SEE TEST
CONDITIONDS)
C
1
f
VSS
7
−2.5 V
2014-11-18
TC4W66FU
Package Dimensions
Weight: 0.02 g (typ.)
8
2014-11-18
TC4W66FU
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively "Product") without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the
Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of
all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes
for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the
instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their
own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such
design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,
diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating
parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR
APPLICATIONS.
• PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH
MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without
limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for
automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions,
safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE
PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your
TOSHIBA sales representative.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the
U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited
except in compliance with all applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES
OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
9
2014-11-18
