TC74VCX162835FT

TC74VCX162835FT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74VCX162835FT Low-Voltage 18-Bit Universal Bus Driver with 3.6-V Tolerant Inputs and Outputs The TC74VCX162835FT is a high-performance CMOS 18-bit universal bus driver. Designed for use in 1.8-V, 2.5-V or 3.3-V systems, it achieves high-speed operation while maintaining the CMOS low power dissipation. It is also designed with overvoltage tolerant inputs and outputs up to 3.6 V. Data flow from A to Y is controlled by the output-enable (OE) input. The device operates in the transparent mode when the latch-enable (LE) input is high. When LE is low, the A data is Weight: 0.25 g (typ.) latched if the clock (CK) input is held at a high or low logic level. If LE is low, the A data is stored in the latch/flip-flop on the low-to-high transition of CK. When OE is high, the outputs are in a high-impedance state. The 26-Ω series resistor helps reducing output overshoot and undershoot without external resistor. All inputs are equipped with protection circuits against static discharge. Features • • • 26-Ω series resistors on outputs Low-voltage operation: VCC = 1.8 to 3.6 V High-speed operation: tpd = 3.9 ns (max) (VCC = 3.0 to 3.6 V) : tpd = 5.0 ns (max) (VCC = 2.3 to 2.7 V) : tpd = 9.8 ns (max) (VCC = 1.8 V) • Output current : IOH/IOL = ±12 mA (min) (VCC = 3.0 V) : IOH/IOL = ±8 mA (min) (VCC = 2.3 V) : IOH/IOL = ±4 mA (min) (VCC = 1.8 V) • • • • Latch-up performance: −300 mA ESD performance: Machine model ≥ ±200 V Human body model ≥ ±2000 V Package: TSSOP 3.6-V tolerant function and power-down protection provided on all inputs and outputs 1 2007-10-19 TC74VCX162835FT Pin Assignment (top view) OE IEC Logic Symbol 27 30 28 EN1 2C3 C3 G2 NC NC Y1 GND Y2 Y3 VCC Y4 Y5 1 2 3 4 5 6 7 8 9 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 GND NC A1 GND A2 A3 VCC A4 A5 A6 GND A7 A8 A9 A10 A11 A12 GND A13 A14 A15 VCC A16 A17 GND A18 CK GND CK LE Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 3 5 6 8 9 10 12 13 14 15 16 17 19 20 21 23 24 26 1 1 3D 54 52 51 49 48 47 45 44 43 42 41 40 38 37 36 34 33 31 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 Y6 10 GND 11 Y7 12 Y8 13 Y9 14 Y10 15 Y11 16 Y12 17 GND 18 Y13 19 Y14 20 Y15 21 VCC 22 Y16 23 Y17 24 GND 25 Y18 26 OE 27 LE 28 2 2007-10-19 TC74VCX162835FT Truth Table Inputs Outputs CK X X X A X L H L H H X Y Z L H L H Y0 (Note) Y0 (Note) OE H L L L L L LE X H H L L L L L L X X: Don’t care Z: High impedance Note: Output level before the indicated steady-state input conditions were established, provided that CK was high or low before LE went low. System Diagram OE CK LE 27 30 28 LE A1 54 D LE D 3 Y1 To 17 other channels 3 2007-10-19 TC74VCX162835FT Absolute Maximum Ratings (Note 1) Characteristics Power supply voltage DC input voltage DC output voltage Input diode current Output diode current DC output current Power dissipation DC VCC/ground current per supply pin Storage temperature Symbol VCC VIN VOUT IIK IOK IOUT PD ICC/IGND Tstg Rating −0.5 to 4.6 −0.5 to 4.6 −0.5 to 4.6 (Note 2) −0.5 to VCC + 0.5 Unit V V V mA (Note 4) mA mA mW mA °C (Note 3) −50 ±50 ±50 400 ±100 −65 to 150 Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: OFF state Note 3: High or low state. IOUT absolute maximum rating must be observed. Note 4: VOUT < GND, VOUT > VCC Operating Ranges (Note 1) Characteristics Power supply voltage Input voltage Output voltage Symbol VCC VIN VOUT Rating 1.8 to 3.6 1.2 to 3.6 −0.3 to 3.6 Unit V V (Note 3) (Note 4) (Note 5) (Note 6) (Note 7) °C (Note 8) ns/V mA V (Note 2) 0 to 3.6 0 to VCC ±12 ±8 ±4 Output current IOH/IOL Topr dt/dv Operating temperature Input rise and fall time −40 to 85 0 to 10 Note 1: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Note 2: Data retention only Note 3: OFF state Note 4: High or low state Note 5: VCC = 3.0 to 3.6 V Note 6: VCC = 2.3 to 2.7 V Note 7: VCC = 1.8 V Note 8: VIN = 0.8 to 2.0 V, VCC = 3.0 V 4 2007-10-19 TC74VCX162835FT Electrical Characteristics < DC Characteristics (Ta = −40 to 85°C, 2.7 V < VCC = 3.6 V) Characteristics H-level L-level Symbol VIH VIL Test Condition ⎯ ⎯ VCC (V) 2.7 to 3.6 2.7 to 3.6 Min 2.0 ⎯ Max ⎯ Unit Input voltage 0.8 ⎯ ⎯ ⎯ ⎯ V IOH = −100 μA H-level VOH VIN = VIH or VIL IOH = −6 mA IOH = −8 mA Output voltage IOH = −12 mA IOL = 100 μA L-level VOL VIN = VIH or VIL IOL = 6 mA IOL = 8 mA IOL = 12 mA Input leakage current 3-state output OFF state current Power-off leakage current Quiescent supply current Increase in ICC per input IIN IOZ IOFF ICC ΔICC 2.7 to 3.6 2.7 3.0 3.0 2.7 to 3.6 2.7 3.0 3.0 2.7 to 3.6 2.7 to 3.6 0 2.7 to 3.6 2.7 to 3.6 2.7 to 3.6 VCC − 0.2 2.2 2.4 2.2 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ V 0.2 0.4 0.55 0.8 ±5.0 ±10.0 μA μA μA VIN = 0 to 3.6 V VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V VIN = VCC or GND VCC < (VIN, VOUT) < 3.6 V = = VIH = VCC − 0.6 V 10.0 20.0 ±20.0 μA 750 < < DC Characteristics (Ta = −40 to 85°C, 2.3 V = VCC = 2.7 V) Characteristics H-level L-level Symbol VIH VIL Test Condition ⎯ ⎯ VCC (V) 2.3 to 2.7 2.3 to 2.7 Min 1.6 ⎯ Max ⎯ Unit Input voltage 0.7 ⎯ ⎯ ⎯ ⎯ V IOH = −100 μA H-level Output voltage VOH VIN = VIH or VIL IOH = −4 mA IOH = −6 mA IOH = −8 mA IOL = 100 μA L-level VOL VIN = VIH or VIL IOL = 6 mA IOL = 8 mA Input leakage current 3-state output OFF state current Power-off leakage current Quiescent supply current IIN IOZ IOFF ICC VIN = 0 to 3.6 V VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V VIN = VCC or GND VCC < (VIN, VOUT) < 3.6 V = = 2.3 to 2.7 2.3 2.3 2.3 2.3 to 2.7 2.3 2.3 2.3 to 2.7 2.3 to 2.7 0 2.3 to 2.7 2.3 to 2.7 VCC − 0.2 2.0 1.8 1.7 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ V 0.2 0.4 0.6 ±5.0 ±10.0 μA μA μA μA 10.0 20.0 ±20.0 5 2007-10-19 TC74VCX162835FT < DC Characteristics (Ta = −40 to 85°C, 1.8 V = VCC < 2.3 V) Characteristics Symbol Test Condition ⎯ ⎯ VCC (V) 1.8 to 2.3 1.8 to 2.3 Min 0.7 × VCC ⎯ Max ⎯ Unit H-level Input voltage L-level VIH VIL 0.2 × VCC ⎯ ⎯ V H-level Output voltage L-level Input leakage current 3-state output OFF state current Power-off leakage current Quiescent supply current VOH VIN = VIH or VIL IOH = −100 μA IOH = −4 mA 1.8 1.8 1.8 1.8 1.8 1.8 0 1.8 1.8 VCC − 0.2 1.4 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ V VOL IIN IOZ IOFF ICC VIN = VIH or VIL VIN = 0 to 3.6 V VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V VIN = VCC or GND IOL = 100 μA IOL = 4 mA 0.2 0.3 ±5.0 ±10.0 μA μA μA μA 10.0 20.0 ±20.0 VCC < (VIN, VOUT) < 3.6 V = = 6 2007-10-19 TC74VCX162835FT AC Characteristics (Ta = −40 to 85°C, input: tr = tf = 2.0 ns, CL = 30 pF, RL = 500 Ω) Characteristics Symbol Test Condition VCC (V) 1.8 Maximum clock frequency fmax Figure 1, Figure 3 2.5 ± 0.2 3.3 ± 0.3 Propagation delay time (An-Yn) tpLH tpHL 1.8 Figure 1, Figure 2 2.5 ± 0.2 3.3 ± 0.3 1.8 Figure 1, Figure 3 2.5 ± 0.2 3.3 ± 0.3 1.8 Figure 1, Figure 4 2.5 ± 0.2 3.3 ± 0.3 1.8 Figure 1, Figure 5 2.5 ± 0.2 3.3 ± 0.3 1.8 Figure 1, Figure 5 2.5 ± 0.2 3.3 ± 0.3 1.8 Figure 1, Figure 3, Figure 4 2.5 ± 0.2 3.3 ± 0.3 1.8 ts Figure 1, Figure 3, Figure 4 2.5 ± 0.2 3.3 ± 0.3 1.8 th Figure 1, Figure 3, Figure 4 2.5 ± 0.2 3.3 ± 0.3 tosLH tosHL 1.8 (Note) 2.5 ± 0.2 3.3 ± 0.3 Min 100 200 250 1.5 0.8 0.6 2.0 1.5 1.4 1.5 0.8 0.6 1.5 0.8 0.6 1.5 0.8 0.6 4.0 1.5 1.5 2.5 1.5 1.5 1.0 0.7 0.7 ⎯ ⎯ ⎯ Max ⎯ ⎯ ⎯ Unit MHz 9.8 5.0 3.9 9.2 5.2 4.2 9.8 5.8 4.7 9.8 5.9 4.3 7.9 4.7 4.2 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ns Propagation delay time (CK-Yn) tpLH tpHL ns Propagation delay time (LE-Yn) tpLH tpHL ns Output enable time tpZL tpZH ns Output disable time tpLZ tpHZ ns Minimum pulse width tW (H) tW (L) ns Minimum setup time (An-CK, An-LE) ns Minimum hold time (An-CK, An-LE) ns 0.5 0.5 0.5 ns Output to output skew Note: Parameter guaranteed by design. (tosLH = |tpLHm − tpLHn|, tosHL = |tpHLm − tpHLn|) 7 2007-10-19 TC74VCX162835FT AC Characteristics (Ta = 0 to 85°C, input: tr = tf = 2.0 ns, CL = 0 pF, RL = 500 Ω) Characteristics Propagation delay time (An-Yn) Propagation delay time (CK-Yn) Propagation delay time (LE-Yn) Output enable time Symbol tpLH tpHL tpLH tpHL tpLH tpHL tpZL tpZH tpLZ tpHZ ts Test Condition VCC (V) (Note) 3.3 ± 0.15 Min Max Unit Figure 1, Figure 2 0.9 2.0 ns Figure 1, Figure 3 (Note) 3.3 ± 0.15 1.4 2.9 ns Figure 1, Figure 4 (Note) 3.3 ± 0.15 0.7 3.4 ns Figure 1, Figure 5 (Note) 3.3 ± 0.15 0.7 3.0 ns Output disable time Minimum set-up time (An-CK, An-LE) Minimum hold time (An-CK, An-LE) Figure 1, Figure 5 (Note) 3.3 ± 0.15 0.7 2.9 ns Figure 1, Figure 3, Figure 4 (Note) 3.3 ± 0.15 1.5 ⎯ ns th Figure 1, Figure 3, Figure 4 (Note) 3.3 ± 0.15 0.7 ⎯ ns Note: TOSHIBA SPICE simulation data. AC Characteristics (Ta = 0 to 85°C, input: tr = tf = 2.0 ns, CL = 50 pF, RL = 500 Ω) Characteristics Propagation delay time (An-Yn) Propagation delay time (CK-Yn) Propagation delay time (LE-Yn) Output enable time Symbol tpLH tpHL tpLH tpHL tpLH tpHL tpZL tpZH tpLZ tpHZ ts Test Condition VCC (V) 3.3 ± 0.15 Min Max Unit Figure 1, Figure 2 1.0 4.2 ns Figure 1, Figure 3 3.3 ± 0.15 1.9 4.5 ns Figure 1, Figure 4 3.3 ± 0.15 1.0 5.0 ns Figure 1, Figure 5 3.3 ± 0.15 1.0 4.6 ns Output disable time Minimum setup time (An-CK, An- LE) Minimum hold time (An-CK, An-LE) Figure 1, Figure 5 3.3 ± 0.15 1.0 4.5 ns Figure 1, Figure 3, Figure 4 3.3 ± 0.15 1.5 ⎯ ns th Figure 1, Figure 3, Figure 4 3.3 ± 0.15 0.7 ⎯ ns 8 2007-10-19 TC74VCX162835FT Dynamic Switching Characteristics (Ta = 25°C, input: tr = tf = 2.0 ns, CL = 30 pF, RL = 500 Ω) Characteristics Symbol Test Condition VCC (V) VIH = 1.8 V, VIL = 0 V Quiet output maximum dynamic VOL VOLP VIH = 2.5 V, VIL = 0 V VIH = 3.3 V, VIL = 0 V VIH = 1.8 V, VIL = 0 V Quiet output minimum dynamic VOL VOLV VIH = 2.5 V, VIL = 0 V VIH = 3.3 V, VIL = 0 V VIH = 1.8 V, VIL = 0 V Quiet output minimum dynamic VOH VOHV VIH = 2.5 V, VIL = 0 V VIH = 3.3 V, VIL = 0 V (Note) (Note) (Note) (Note) (Note) (Note) (Note) (Note) (Note) 1.8 2.5 3.3 1.8 2.5 3.3 1.8 2.5 3.3 Typ. 0.25 0.35 0.45 −0.25 −0.35 −0.45 Unit V V 1.35 1.85 2.45 V Note: Parameter guaranteed by design. Capacitive Characteristics (Ta = 25°C) Characteristics Input capacitance Output capacitance Power dissipation capacitance Symbol CIN COUT CPD fIN = 10 MHz Test Condition VCC (V) ⎯ ⎯ Typ. 6 7 20 Unit pF pF pF 1.8, 2.5, 3.3 1.8, 2.5, 3.3 (Note) 1.8, 2.5, 3.3 Note: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC/18 (per bit) 9 2007-10-19 TC74VCX162835FT AC Test Circuit 6.0 V or VCC × 2 Open GND Measure CL RL Switch RL Parameter tpLH, tpHL tpLZ, tpZL tpHZ, tpZH 6.0 V VCC × 2 Switch Open @VCC = 3.3 ± 0.3 V @VCC = 2.5 ± 0.2 V @VCC = 1.8 V GND Output CL = 0, 30, 50 pF RL = 500 Ω Figure 1 AC Waveform tr 2.0 ns Input (An) tf 2.0 ns 90% VM VIH 10% GND VOH VM tpLH tpHL VOL Output (Yn) Figure 2 tpLH, tpHL tr 2.0 ns Input (CK) tf 2.0 ns VIH GND tw (H) tw (L) VIH VM ts (H) th (H) ts (L) th (L) GND VOH VM VOL 10% 90% VM Input (An) Output (Yn) tpHL tpLH Figure 3 tpLH, tpHL, tw, ts, th 10 2007-10-19 TC74VCX162835FT tf 2.0 ns Input (LE) tr 2.0 ns 90% VM VIH VM GND tw (H) VIH VM GND ts (H) Output (Yn) VM tpLH tpHL th (H) ts (L) th (L) VOH VM tpHL tpLH VOL VM tr 2.0 ns 10% tf 2.0 ns Input (An) 90% 10% VM Figure 4 tpLH, tpHL, tw, ts, th tr 2.0 ns Output Enable Control ( OE ) tpLZ Output (Yn) Low to Off to Low tpHZ Output (Yn) High to Off to High Outputs enabled tf 2.0 ns 90% VM VIH 10% tpZL 3.0 V or VCC VM VX tpZH VOL VOH VM GND Outputs disabled Outputs enabled GND VY Figure 5 tpLZ, tpHZ, tpZL, tpZH Symbol VIH VM VX VY VCC 3.3 ± 0.3 V 2.7 V 1.5 V VOL + 0.3 V VOH − 0.3 V 2.5 ± 0.2 V VCC VCC/2 VOL + 0.15 V VOH − 0.15 V 1.8 V VCC VCC/2 VOL + 0.15 V VOH − 0.15 V 11 2007-10-19 TC74VCX162835FT IBIS Characteristics (typ.) 0 PC-100 requirement PC-100 requirement VCX162835 (VCC = 3.15 V) VCX162835 (VCC = 3.45 V) −20 IOH (mA) High-level output current −40 −60 −80 −100 0 0.5 1.0 1.5 2.0 2.5 3.0 High-level output voltage VOH (V) Figure 6 I/V characteristics vs. pull-up 120 100 PC-100 requirement PC-100 requirement VCX162835 (VCC = 3.15 V) VCX162835 (VCC = 3.45 V) IOL (mA) Low-level output current 80 60 40 20 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Low-level output voltage VOL (V) Figure 7 I/V characteristics vs. pull-down 12 2007-10-19 TC74VCX162835FT Package Dimensions Weight: 0.25 g (typ.) 13 2007-10-19 TC74VCX162835FT RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN GENERAL • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 14 2007-10-19