TC74VCX16501FT

TC74VCX16501FT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74VCX16501FT Low-Voltage 18-Bit Universal Bus Transceiver with 3.6-V Tolerant Inputs and Outputs The TC74VCX16501FT is a high performance CMOS 18-bit universal bus transceiver. Designed for use in 1.8-V, 2.5-V or 3.3-V systems, it achieves high-speed operation while maintaining the CMOS low power dissipation. It is also designed with overvoltage tolerant inputs and outputs up to 3.6 V. Data flow in each direction is controlled by output-enable (OEAB and OEBA), latch-enable (LEAB and LEBA), and clock (CKAB and CKBA) inputs. For A-to-B data flow, the device operates in the transparent Weight: 0.25 g (typ.) mode when LEAB is high. When LEAB is low, the A data is latched if CKAB is held at a high or low logic level. If LEAB is low, the A bus data is stored in the latch/flip-flop on the low-to-high transition of CKAB. Data flow for B to A is similar to that of A to B but uses OEBA, LEBA, and CKBA. When the OE input is high, the outputs are in a high-impedance state. This device is designed to be used with 3-state memory address drivers, etc. All inputs are equipped with protection circuits against static discharge. Features (Note) • • Low-voltage operation: VCC = 1.8 to 3.6 V High-speed operation: tpd = 2.9 ns (max) (VCC = 3.0 to 3.6 V) : tpd = 3.5 ns (max) (VCC = 2.3 to 2.7 V) : tpd = 7.0 ns (max) (VCC = 1.8 V) • Output current : IOH/IOL = ±24 mA (min) (VCC = 3.0 V) : IOH/IOL = ±18 mA (min) (VCC = 2.3 V) : IOH/IOL = ±6 mA (min) (VCC = 1.8 V) • • • • • Latch-up performance: −300 mA ESD performance: Machine model ≥ ±200 V Human body model ≥ ±2000 V Package: TSSOP Bidirectional interface between 2.5 V and 3.3 V signals. 3.6-V tolerant function and power-down protection provided on all inputs and outputs Note: Do not apply a signal to any bus pins when it is in the output mode. Damage may result. All floating (high impedance) bus pins must have their input level fixed by means of pull-up or pull-down resistors. 1 2007-10-19 TC74VCX16501FT Pin Assignment (top view) OEAB IEC Logic Symbol 1 55 2 27 30 28 EN1 2C3 C3 G2 EN4 5C6 C6 G5 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 3 5 6 8 9 10 12 13 14 15 16 17 19 20 21 23 24 26 3D 1 1 54 52 51 49 48 47 45 44 43 42 41 40 38 37 36 34 33 31 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 OEAB LEAB A1 GND A2 A3 VCC A4 A5 1 2 3 4 5 6 7 8 9 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 GND CKAB B1 GND B2 B3 VCC B4 B5 B6 GND B7 B8 B9 B10 B11 B12 GND B13 B14 B15 VCC B16 B17 GND B18 CKBA GND CKAB LEAB OEBA CKBA LEBA 4 1 6D A6 10 GND 11 A7 12 A8 13 A9 14 A10 15 A11 16 A12 17 GND 18 A13 19 A14 20 A15 21 VCC 22 A16 23 A17 24 GND 25 A18 26 OEBA 27 LEBA 28 2 2007-10-19 TC74VCX16501FT Truth Table (A bus → B bus) Inputs OEAB L H H H H H LEAB X H H L L L H CKAB X X X A X L H L H X Outputs B Z L H L H B0 (Note) B0 (Note) H L L X Note: Output level before the indicated steady-state input conditions were established, provided that CKAB was low or high before LEAB went low. Truth Table (B bus → A bus) Inputs OEBA H L L L L L LEBA X H H L L L H CKBA X X X B X L H L H X Outputs A Z L H L H A0 (Note) A0 (Note) L L L X Note: Output level before the indicated steady-state input conditions were established, provided that CKBA was low or high before LEBA went low. 3 2007-10-19 TC74VCX16501FT System Diagram OEAB CKBA LEBA OEBA 1 30 28 27 55 2 LE LE D 54 CKAB LEAB B1 A1 3 D LE D LE D To 17 other channels Absolute Maximum Ratings (Note 1) Characteristics Power supply voltage DC input voltage (OEAB, OEBA , LEAB, LEBA, CKAB, CKBA) DC bus I/O voltage Input diode current Output diode current DC output current Power dissipation DC VCC/ground current per supply pin Storage temperature VIN −0.5 to 4.6 −0.5 to 4.6 (Note 2) Symbol VCC Rating −0.5 to 4.6 Unit V V VI/O IIK IOK IOUT PD ICC/IGND Tstg −0.5 to VCC + 0.5 V mA (Note 3) −50 ±50 ±50 (Note 4) mA mA mW mA °C 400 ±100 −65 to 150 Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: OFF state Note 3: High or low state. IOUT absolute maximum rating must be observed. Note 4: VOUT < GND, VOUT > VCC 4 2007-10-19 TC74VCX16501FT Operating Ranges (Note 1) Characteristics Power supply voltage Input voltage (OEAB, OEBA , LEAB, LEBA, CKAB, CKBA) Bus I/O voltage VIN −0.3 to 3.6 Symbol VCC Rating 1.8 to 3.6 1.2 to 3.6 (Note 2) Unit V V (Note 3) (Note 4) (Note 5) (Note 6) (Note 7) °C (Note 8) ns/V mA VI/O 0 to 3.6 0 to VCC ±24 V Output current IOH/IOL ±18 ±6 Operating temperature Input rise and fall time Topr dt/dv −40 to 85 0 to 10 Note 1: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Note 2: Data retention only Note 3: OFF state Note 4: High or low state Note 5: VCC = 3.0 to 3.6 V Note 6: VCC = 2.3 to 2.7 V Note 7: VCC = 1.8 V Note 8: VIN = 0.8 to 2.0 V, VCC = 3.0 V 5 2007-10-19 TC74VCX16501FT Electrical Characteristics < DC Characteristics (Ta = −40 to 85°C, 2.7 V < VCC = 3.6 V) Characteristics H-level L-level Symbol VIH VIL Test Condition ⎯ ⎯ VCC (V) 2.7 to 3.6 2.7 to 3.6 Min 2.0 ⎯ Max ⎯ Unit Input voltage 0.8 ⎯ ⎯ ⎯ ⎯ V IOH = −100 μA H-level VOH VIN = VIH or VIL IOH = −12 mA IOH = −18 mA Output voltage IOH = −24 mA IOL = 100 μA L-level VOL VIN = VIH or VIL IOL = 12 mA IOL = 18 mA IOL = 24 mA Input leakage current 3-state output OFF state current Power-off leakage current Quiescent supply current Increase in ICC per input IIN IOZ IOFF ICC ΔICC 2.7 to 3.6 2.7 3.0 3.0 2.7 to 3.6 2.7 3.0 3.0 2.7 to 3.6 2.7 to 3.6 0 2.7 to 3.6 2.7 to 3.6 2.7 to 3.6 VCC − 0.2 2.2 2.4 2.2 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ V 0.2 0.4 0.4 0.55 ±5.0 ±10.0 μA μA μA VIN = 0 to 3.6 V VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V VIN = VCC or GND VCC < (VIN, VOUT) < 3.6 V = = VIH = VCC − 0.6 V 10.0 20.0 ±20.0 μA 750 < < DC Characteristics (Ta = −40 to 85°C, 2.3 V = VCC = 2.7 V) Characteristics H-level L-level Symbol VIH VIL Test Condition ⎯ ⎯ VCC (V) 2.3 to 2.7 2.3 to 2.7 Min 1.6 ⎯ Max ⎯ Unit Input voltage 0.7 ⎯ ⎯ ⎯ ⎯ V IOH = −100 μA H-level Output voltage VOH VIN = VIH or VIL IOH = −6 mA IOH = −12 mA IOH = −18 mA IOL = 100 μA L-level VOL VIN = VIH or VIL IOL = 12 mA IOL = 18 mA Input leakage current 3-state output OFF state current Power-off leakage current Quiescent supply current IIN IOZ IOFF ICC VIN = 0 to 3.6 V VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V VIN = VCC or GND VCC < (VIN, VOUT) < 3.6 V = = 2.3 to 2.7 2.3 2.3 2.3 2.3 to 2.7 2.3 2.3 2.3 to 2.7 2.3 to 2.7 0 2.3 to 2.7 2.3 to 2.7 VCC − 0.2 2.0 1.8 1.7 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ V 0.2 0.4 0.6 ±5.0 ±10.0 μA μA μA μA 10.0 20.0 ±20.0 6 2007-10-19 TC74VCX16501FT < DC Characteristics (Ta = −40 to 85°C, 1.8 V = VCC < 2.3 V) Characteristics Symbol Test Condition ⎯ ⎯ VCC (V) 1.8 to 2.3 1.8 to 2.3 Min 0.7 × VCC ⎯ Max ⎯ Unit H-level Input voltage L-level VIH VIL 0.2 × VCC ⎯ ⎯ V H-level Output voltage L-level Input leakage current 3-state output OFF state current Power-off leakage current Quiescent supply current VOH VIN = VIH or VIL IOH = −100 μA IOH = −6 mA 1.8 1.8 1.8 1.8 1.8 1.8 0 1.8 1.8 VCC − 0.2 1.4 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ V VOL IIN IOZ IOFF ICC VIN = VIH or VIL VIN = 0 to 3.6 V VIN = VIH or VIL VOUT = 0 to 3.6 V VIN, VOUT = 0 to 3.6 V VIN = VCC or GND IOL = 100 μA IOL = 6 mA 0.2 0.3 ±5.0 ±10.0 μA μA μA μA 10.0 20.0 ±20.0 VCC < (VIN, VOUT) < 3.6 V = = 7 2007-10-19 TC74VCX16501FT AC Characteristics (Ta = −40 to 85°C, input: tr = tf = 2.0 ns, CL = 30 pF, RL = 500 Ω) (Note 1) Characteristics Symbol Test Condition VCC (V) 1.8 Maximum clock frequency fmax Figure 1, Figure 3 2.5 ± 0.2 3.3 ± 0.3 Propagation delay time (An, Bn-Bn, An) tpLH tpHL 1.8 Figure 1, Figure 2 2.5 ± 0.2 3.3 ± 0.3 1.8 Figure 1, Figure 3 2.5 ± 0.2 3.3 ± 0.3 1.8 Figure 1, Figure 4 2.5 ± 0.2 3.3 ± 0.3 1.8 Figure 1, Figure 5, Figure 6 2.5 ± 0.2 3.3 ± 0.3 1.8 Figure 1, Figure 5, Figure 6 2.5 ± 0.2 3.3 ± 0.3 1.8 Figure 1, Figure 3, Figure 4 2.5 ± 0.2 3.3 ± 0.3 1.8 Minimum set-up time ts Figure 1, Figure 3, Figure 4 2.5 ± 0.2 3.3 ± 0.3 1.8 Minimum hold time th Figure 1, Figure 3, Figure 4 2.5 ± 0.2 3.3 ± 0.3 tosLH tosHL 1.8 (Note 2) 2.5 ± 0.2 3.3 ± 0.3 Min 100 200 250 1.5 0.8 0.6 1.5 0.8 0.6 1.5 0.8 0.6 1.5 0.8 0.6 1.5 0.8 0.6 4.0 1.5 1.5 2.5 1.5 1.5 1.0 1.0 1.0 ⎯ ⎯ ⎯ Max ⎯ ⎯ ⎯ Unit MHz 7.0 3.5 2.9 8.8 4.4 3.5 9.8 4.9 3.8 9.8 4.9 3.8 7.6 4.2 3.7 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ns Propagation delay time (CKAB, CLKBA-Bn, An) tpLH tpHL ns Propagation delay time (LEAB, LEBA-Bn, An) tpLH tpHL ns Output enable time (OEAB, OEBA -Bn, An) tpZL tpZH ns Output disable time (OEAB, OEBA -Bn, An) tpLZ tpHZ ns Minimum pulse width tW (H) tW (L) ns ns ns 0.5 0.5 0.5 ns Output to output skew Note 1: For CL = 50 pF, add approximately 300 ps to the AC maximum specification. Note 2: Parameter guaranteed by design. (tosLH = |tpLHm − tpLHn|, tosHL = |tpHLm − tpHLn|) 8 2007-10-19 TC74VCX16501FT Dynamic Switching Characteristics (Ta = 25°C, input: tr = tf = 2.0 ns, CL = 30 pF, RL = 500 Ω) Characteristics Symbol Test Condition VCC (V) VIH = 1.8 V, VIL = 0 V Quiet output maximum dynamic VOL VOLP VIH = 2.5 V, VIL = 0 V VIH = 3.3 V, VIL = 0 V VIH = 1.8 V, VIL = 0 V Quiet output minimum dynamic VOL VOLV VIH = 2.5 V, VIL = 0 V VIH = 3.3 V, VIL = 0 V VIH = 1.8 V, VIL = 0 V Quiet output minimum dynamic VOH VOHV VIH = 2.5 V, VIL = 0 V VIH = 3.3 V, VIL = 0 V (Note) (Note) (Note) (Note) (Note) (Note) (Note) (Note) (Note) 1.8 2.5 3.3 1.8 2.5 3.3 1.8 2.5 3.3 Typ. 0.25 0.6 0.8 −0.25 −0.6 −0.8 Unit V V 1.5 1.9 2.2 V Note: Parameter guaranteed by design. Capacitive Characteristics (Ta = 25°C) Characteristics Input capacitance Bus I/O capacitance Power dissipation capacitance Symbol CIN CI/O CPD fIN = 10 MHz Test Condition VCC (V) ⎯ ⎯ Typ. 6 7 20 Unit pF pF pF 1.8, 2.5, 3.3 1.8, 2.5, 3.3 (Note) 1.8, 2.5, 3.3 Note: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC/18 (per bit) 9 2007-10-19 TC74VCX16501FT AC Test Circuit 6.0 V or VCC × 2 Open GND Measure CL RL Switch RL Parameter tpLH, tpHL tpLZ, tpZL tpHZ, tpZH 6.0 V VCC × 2 Switch Open @VCC = 3.3 ± 0.3 V @VCC = 2.5 ± 0.2 V @VCC = 1.8 V GND Output CL = 30 pF RL = 500 Ω Figure 1 AC Waveform tr 2.0 ns Input (An, Bn) tf 2.0 ns 90% VM VIH 10% GND VOH VM tpLH tpHL VOL Output (Bn, An) Figure 2 tpLH, tpHL tr 2.0 ns Input (CKAB, CKBA) tf 2.0 ns VIH GND tw (H) tw (L) VIH VM ts (H) th (H) ts (L) th (L) GND VOH VM VOL 10% 90% VM Input (An, Bn) Output (Bn, An) tpHL tpLH Figure 3 tpLH, tpHL, tw, ts, th 10 2007-10-19 TC74VCX16501FT tf 2.0 ns Input (LE) tr 2.0 ns Input (An, Bn) 90% 10% VM ts (H) Output (Bn, An) VM tpLH tpHL th (H) tr 2.0 ns 90% VM VIH VM GND tw (H) VIH VM GND ts (L) th (L) VOH VM tpHL tpLH VOL 10% tf 2.0 ns Figure 4 tpLH, tpHL, tw, ts, th tr 2.0 ns Output Enable Control ( OEBA ) tpLZ Output (An) Low to Off to Low tpHZ Output (An) High to Off to High Outputs enabled tf 2.0 ns 90% VM VIH 10% tpZL 3.0 V or VCC VM VX tpZH VOL VOH VM GND Outputs disabled Outputs enabled GND VY Figure 5 tpLZ, tpHZ, tpZL, tpZH 11 2007-10-19 TC74VCX16501FT tf 2.0 ns Output Enable Control (OEAB) tr 2.0 ns 90% VM VIH GND 3.0 V or VCC VM VX tpZL VOL VOH VM tpZH GND 10% Output (Bn) Low to Off to Low tpLZ Output (Bn) High to Off to High tpHZ VY Figure 6 tpLZ, tpHZ, tpZL, tpZH VCC 3.3 ± 0.3 V 2.7 V 1.5 V VOL + 0.3 V VOH − 0.3 V 2.5 ± 0.2 V VCC VCC/2 VOL + 0.15 V VOH − 0.15 V 1.8 V VCC VCC/2 VOL + 0.15 V VOH − 0.15 V Symbol VIH VM VX VY 12 2007-10-19 TC74VCX16501FT Package Dimensions Weight: 0.25 g (typ.) 13 2007-10-19 TC74VCX16501FT RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN GENERAL • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 14 2007-10-19