TC7MH4040FK_07

TC7MH4040FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7MH4040FK 12-Stage Ripple-Carry Binary Counter The TC7MH4040FK is an advanced high speed CMOS 12-stage ripple-carry binary counter fabricated with silicon gate C2MOS technology. It achieves the high speed operation similar to equivalent bipolar schottky TTL while maintaining the CMOS low power dissipation. Setting CLR to high resets the counter to low. A negative transition on the CK input brings one increment into the counter. This counter provides all divided output stages, and at Q12, a 1/4096 divided frequency will be output. An input protection circuit ensures that 0 to 5.5 V can be Weight: 0.02 g (typ.) applied to the input pins without regard to the supply voltage. This device can be used to interface 5 V to 3 V systems and two supply systems such as battery back up. This circuit prevents device destruction due to mismatched supply and input voltages. Features • • • • • • • • High speed: fmax = 210 MHz (typ.) (VCC = 5 V) Low power dissipation: ICC = 4 μA (max) (Ta = 25°C) High noise immunity: VNIH = VNIL = 28% VCC (min) Power down protection is provided on all inputs. Balanced propagation delays: tpLH ≈ tpHL Wide operating voltage range: VCC (opr) = 2~5.5 V Low noise: VOLP = 1.5 V (max) Pin and function compatible with 74HC4040 1 2007-10-19 TC7MH4040FK Pin Assignment (top view) IEC Logic Level RCTR 12 0 CLR (11) CT = 0 (9) (7) (6) (5) (3) CK (10) (2) +CT (4) (13) (12) Q3 Q2 GND 6 7 8 11 10 9 CLR CK Q1 11 (14) (15) (1) Q12 Q6 Q5 Q7 Q4 1 2 3 4 5 16 15 14 13 12 VCC Q11 Q10 Q8 Q9 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12 Truth Table CK X CLR H L L Outputs All outputs = “L” No change Advance to next state X: Don’t care 2 2007-10-19 TC7MH4040FK System Diagram Q1 9 Q2 7 Q3 6 Q4 5 Q5 3 Q6 2 D D D D D D CK 10 CK Q R CK Q R CK Q R CK Q R CK Q R CK Q R CLR 11 R Q CK R Q CK R Q CK R Q CK R Q CK R Q CK D D D D D D 1 Q12 15 Q11 14 Q10 12 Q9 13 Q8 4 Q7 Absolute Maximum Ratings (Note) Characteristics Supply voltage range DC input voltage DC output voltage Input diode current Output diode current DC output current DC VCC/ground current Power dissipation Storage temperature Symbol VCC VIN VOUT IIK IOK IOUT ICC PD Tstg Rating −0.5~7.0 −0.5~7.0 −0.5~VCC + 0.5 −20 ±20 ±25 ±100 180 −65~150 Unit V V V mA mA mA mA mW °C Note: Exceeding any of the absolute maximum ratings, even briefly, may lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). 3 2007-10-19 TC7MH4040FK Operating Ranges (Note) Characteristics Supply voltage Input voltage Output voltage Operating temperature Input rise and fall time Symbol VCC VIN VOUT Topr dt/dv Rating 2.0~5.5 0~5.5 0~VCC −40~85 0~100 (VCC = 3.3 ± 0.3 V) 0~20 (VCC = 5 ± 0.5 V) Unit V V V °C ns/V Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Electrical Characteristics DC Characteristics Characteristics Symbol Test Condition VCC (V) 2.0 High level Input voltage Low level VIL ⎯ VIH ⎯ 3.0~5.5 2.0 3.0~5.5 2.0 IOH = −50 μA High level VOH VIN = VIH or VIL IOH = −4 mA Output voltage IOH = −8 mA 3.0 4.5 3.0 4.5 2.0 IOL = 50 μA Low level VOL VIN = VIH or VIL IOL = 4 mA IOL = 8 mA Input leakage current Quiescent supply current IIN ICC VIN = 5.5 V or GND VIN = VCC or GND 3.0 4.5 3.0 4.5 0~5.5 5.5 Min 1.50 VCC × 0.7 ⎯ ⎯ 1.9 2.9 4.4 2.58 3.94 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Ta = 25°C Typ. ⎯ ⎯ ⎯ ⎯ 2.0 3.0 4.5 ⎯ ⎯ 0 0 0 ⎯ ⎯ ⎯ ⎯ Max ⎯ ⎯ 0.50 VCC × 0.3 ⎯ ⎯ ⎯ ⎯ ⎯ 0.1 0.1 0.1 0.36 0.36 ±0.1 4.0 Ta = −40~85°C Min 1.50 VCC × 0.7 ⎯ ⎯ 1.9 2.9 4.4 2.48 3.80 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Max ⎯ ⎯ 0.50 VCC × 0.3 ⎯ ⎯ ⎯ ⎯ ⎯ 0.1 0.1 0.1 0.44 0.44 ±1.0 40.0 μA μA V V Unit Timing Requirements (Input: tr = tf = 3 ns) Characteristics Minimum pulse width ( CK ) Minimum pulse width (CLR) Minimum removal time Symbol tw (L) tw (H) tw (H) Test Condition VCC (V) ⎯ 3.3 ± 0.3 5.0 ± 0.5 3.3 ± 0.3 5.0 ± 0.5 3.3 ± 0.3 5.0 ± 0.5 Ta = 25°C Typ. ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Limit 5.0 5.0 5.0 5.0 5.0 5.0 Ta = −40~85°C Limit 5.0 5.0 5.0 5.0 5.0 5.0 Unit ns ⎯ ns trem ⎯ ns 4 2007-10-19 TC7MH4040FK AC Characteristics (Input: tr = tf = 3 ns) Characteristics Symbol Test Condition VCC (V) CL (pF) 3.3 ± 0.3 tpLH tpHL ⎯ 5.0 ± 0.5 3.3 ± 0.3 5.0 ± 0.5 3.3 ± 0.3 tpHL ⎯ 5.0 ± 0.5 15 50 15 50 50 50 15 50 15 50 15 50 15 50 Min ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 75 55 150 95 ⎯ (Note) ⎯ Ta = 25°C Typ. 7.5 10.0 4.8 6.3 2.4 1.6 8.3 10.8 5.6 7.1 140 80 210 125 4 21 Max 11.9 15.4 7.3 9.3 4.4 3.1 12.8 16.3 8.6 10.6 ⎯ ⎯ ⎯ ⎯ 10 ⎯ Ta = −40~85°C Min 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 75 50 125 80 ⎯ ⎯ Max 14.0 17.5 8.5 10.5 5.0 3.5 15.0 18.5 10.0 12.0 ⎯ ⎯ ⎯ ⎯ 10 ⎯ pF pF MHz ns ns ns Unit Propagation delay time ( CK - Q1) Propagation delay time (Qn - Qn + 1) Δtpd ⎯ Propagation delay time (CLR - Q) 3.3 ± 0.3 Maximum clock frequency fmax ⎯ 5.0 ± 0.5 Input capacitance Power dissipation capacitance CIN CPD ⎯ Note: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC Noise Characteristics (Input: tr = tf = 3 ns) Characteristics Quiet output maximum dynamic VOL Quiet output minimum dynamic VOL Minimum high level dynamic input voltage VIH Minimum low level dynamic input voltage VIL Symbol VOLP VOLV VIHD VILD Test Condition VCC (V) CL = 50 pF CL = 50 pF CL = 50 pF CL = 50 pF 5.0 5.0 5.0 5.0 Ta = 25°C Typ. 1.2 −1.2 ⎯ ⎯ Limit 1.5 −1.5 3.5 1.5 Unit V V V V Input Equivalent Circuit Input 5 2007-10-19 TC7MH4040FK Package Dimensions Weight: 0.02 g (typ.) 6 2007-10-19 TC7MH4040FK RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN GENERAL • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 7 2007-10-19