TC7SHU04FS

TC7SHU04FS TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7SHU04FS INVERTER (Un-Buffer) Features High speed: tpd = 3.5 ns (typ.) at VCC = 5 V Low power dissipation: ICC = 2 μA (max) at Ta = 25°C High noise immunity: VNIH = VNIL = 10% VCC (min) 5.5V tolerant input. Wide operating voltage range: VCC (opr) = 2~5.5 V SON5-P-0.35 (fSV) (top view) Type Name Marking ・Pin Assignment Weight : 0.001 g (Typ.) H 6 IN A 1 5 VCC GND 2 NC 3 4 OUT Y 1 2007-11-01 TC7SHU04FS Absolute Maximum Ratings (Ta = 25°C) Characteristics Supply voltage range DC input voltage DC output voltage Input diode current Output diode current DC output current DC VCC/ground current Power dissipation Storage temperature Symbol VCC VIN VOUT IIK IOK IOUT ICC PD Tstg Rating −0.5~7.0 −0.5~7.0 −0.5~VCC + 0.5 −20 ±20 ±25 ±50 50 −65~150 Unit V V V mA mA mA mA mW °C Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Logic Diagram Truth Table A L H Y H L IN A 1 OUT Y Operating Ranges Characteristics Supply voltage Input voltage Output voltage Operating temperature Symbol VCC VIN VOUT Topr Rating 2.0~5.5 0~5.5 0~VCC −40~85 Unit V V V °C 2 2007-11-01 TC7SHU04FS Electrical Characteristics DC Characteristics Ta = 25°C Characteristics Symbol Test Condition VCC (V) 2.0 VIH ⎯ 3.0~ 5.5 2.0 VIL ⎯ 3.0~ 5.5 2.0 High-level output voltage VIN = VIL VOH VIN =GND IOH = −4 mA IOH = −8 mA IOH = −50 μA 3.0 4.5 3.0 4.5 2.0 Low-level output voltage VIN = VIH VOL VIN =VCC Input leakage current Quiescent supply current IIN ICC IOL = 4 mA IOL = 8 mA IOL = 50 μA 3.0 4.5 3.0 4.5 0~ 5.5 5.5 Min 1.70 VCC × 0.8 ⎯ ⎯ 1.8 2.7 4.0 2.58 3.94 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Typ. ⎯ ⎯ ⎯ ⎯ 2.0 3.0 4.5 ⎯ ⎯ 0.0 0.0 0.0 ⎯ ⎯ ⎯ ⎯ Max ⎯ ⎯ 0.30 VCC × 0.2 ⎯ ⎯ ⎯ ⎯ ⎯ 0.2 0.3 0.5 0.36 0.36 ±0.1 2.0 Ta = −40~85°C Min 1.70 VCC × 0.8 ⎯ ⎯ 1.8 2.7 4.0 2.48 3.80 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Max ⎯ ⎯ 0.30 VCC × 0.2 ⎯ ⎯ ⎯ ⎯ ⎯ 0.2 0.3 0.5 0.44 0.44 ±1.0 20.0 μA μA V V V V Unit High-level input voltage Low-level input voltage VIN = 5.5 V or GND VIN = VCC or GND 3 2007-11-01 TC7SHU04FS AC Characteristics (Input: tr = tf = 3 ns) Characteristics Symbol Test Circuit Test Condition VCC (V) 3.3 ± 0.3 ⎯ ⎯ 5.0 ± 0.5 ⎯ ⎯ ⎯ (Note) CL (pF) 15 50 15 50 Min ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Ta = 25°C Typ. 5.0 7.5 3.5 5.0 5 6 Max 8.9 11.4 5.5 7.0 10 ⎯ Ta = −40~85°C Min 1.0 1.0 1.0 1.0 ⎯ ⎯ Max 10.5 13.0 6.5 8.0 10 ⎯ pF pF ns Unit Propagation delay time tpLH tpHL Input capacitance Power dissipation capacitance CIN CPD Note: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC 4 2007-11-01 TC7SHU04FS Package Dimensions SON5-P-0.35 Unit:mm Weight: 0.001 g (typ.) 5 2007-11-01 TC7SHU04FS RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN GENERAL • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 6 2007-11-01