TK3A60DA
TOSHIBA Field Effect Transistor Silicon N Channel MOS Type (π-MOSⅦ)
TK3A60DA
Switching Regulator Applications
•
•
•
•
Unit: mm
Low drain-source ON-resistance: RDS (ON) = 2.2 Ω(typ.)
High forward transfer admittance: |Yfs| = 1.5 S (typ.)
Low leakage current: IDSS = 10 μA (max) (VDS = 600 V)
Enhancement mode: Vth = 2.4 to 4.4 V (VDS = 10 V, ID = 1 mA)
Absolute Maximum Ratings (Ta = 25°C)
Characteristics
Symbol
Rating
Unit
Drain-source voltage
VDSS
600
V
Gate-source voltage
VGSS
±30
V
DC
(Note 1)
ID
2.5
Pulse
(Note 1)
IDP
10
Drain power dissipation (Tc = 25°C)
PD
30
W
Single pulse avalanche energy
(Note 2)
EAS
180
mJ
Avalanche current
IAR
2.5
A
Repetitive avalanche energy (Note 3)
EAR
3.0
mJ
JEITA
Channel temperature
Tch
150
°C
TOSHIBA
Storage temperature range
Tstg
−55 to 150
°C
Weight: 1.7 g (typ.)
Drain current
A
1: Gate
2: Drain
3: Source
⎯
JEDEC
SC-67
2-10U1B
Note: Using continuously under heavy loads (e.g. the application of high
temperature/current/voltage and the significant change in temperature, etc.) may cause this product to
decrease in the reliability significantly even if the operating conditions (i.e. operating
temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate
reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating
Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc).
Thermal Characteristics
2
Characteristics
Symbol
Max
Unit
Thermal resistance, channel to case
Rth (ch-c)
4.17
°C/W
Thermal resistance, channel to ambient
Rth (ch-a)
62.5
°C/W
Note 1: Ensure that the channel temperature does not exceed 150°C.
1
Note 2: VDD = 90 V, Tch = 25°C (initial), L = 50 mH, RG = 25 Ω, IAR = 2.5 A
Note 3: Repetitive rating: pulse width limited by maximum channel temperature
This transistor is an electrostatic-sensitive device. Handle with care.
3
Start of commercial production
2008-11
1
2013-11-01
TK3A60DA
Electrical Characteristics (Ta = 25°C)
Characteristics
Symbol
Test Condition
Min
Typ.
Max
Unit
Gate leakage current
IGSS
VGS = ±30 V, VDS = 0 V
⎯
⎯
±1
μA
Drain cut-off current
IDSS
VDS = 600V, VGS = 0 V
⎯
⎯
10
μA
V (BR) DSS
ID = 10 mA, VGS = 0 V
600
⎯
⎯
V
Vth
VDS = 10 V, ID = 1 mA
2.4
⎯
4.4
V
Drain-source ON resistance
RDS (ON)
VGS = 10 V, ID =1.3 A
⎯
2.2
2.8
Ω
Forward transfer admittance
|Yfs|
VDS = 10 V, ID =1.3 A
0.4
1.5
⎯
S
Input capacitance
Ciss
⎯
380
⎯
Reverse transfer capacitance
Crss
⎯
2.5
⎯
Output capacitance
Coss
⎯
45
⎯
⎯
15
⎯
⎯
35
⎯
⎯
7
⎯
⎯
55
⎯
⎯
9
⎯
⎯
5
⎯
⎯
4
⎯
Drain-source breakdown voltage
Gate threshold voltage
Rise time
VDS = 25 V, VGS = 0 V, f = 1 MHz
Turn-on time
ton
VOUT
RL = 154 Ω
50 Ω
Switching time
Fall time
ID = 1.3 A
10 V
VGS
0V
tr
tf
pF
ns
VDD ≈ 200 V
Turn-off time
toff
Duty ≦ 1%, tw = 10 μs
Total gate charge
Qg
Gate-source charge
Qgs
Gate-drain charge
Qgd
VDD ≈ 400 V, VGS = 10 V, ID = 2.5 A
nC
Source-Drain Ratings and Characteristics (Ta = 25°C)
Characteristics
Symbol
Test Condition
Min
Typ.
Max
Unit
(Note 1)
IDR
⎯
⎯
⎯
2.5
A
(Note 1)
IDRP
⎯
⎯
⎯
10
A
Continuous drain reverse current
Pulse drain reverse current
Forward voltage (diode)
VDSF
IDR = 2.5 A, VGS = 0 V
⎯
⎯
−1.7
V
Reverse recovery time
trr
IDR = 2.5 A, VGS = 0 V,
⎯
700
⎯
ns
Reverse recovery charge
Qrr
dIDR/dt = 100 A/μs
⎯
3.5
⎯
μC
Marking
Note 4 : A line under a Lot No. identifies the indication of product Labels
[[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]]
K3A60DA
Part No.
(or abbreviation code)
Lot No.
Please contact your TOSHIBA sales representative for details as to
environmental matters such as the RoHS compatibility of Product.
The RoHS is Directive 2011/65/EU of the European Parliament and
of the Council of 8 June 2011 on the restriction of the use of certain
hazardous substances in electrical and electronic equipment
Note 4
2
2013-11-01
TK3A60DA
ID – VDS
COMMON SOURCE
Tc = 25°C
PULSE TEST
10
7
8
(A)
1.6
ID – VDS
5
1.2
DRAIN CURRENT ID
DRAIN CURRENT ID
(A)
2
6
0.8
5.75
VGS = 5.5 V
0.4
COMMON
10
SOURCE
Tc = 25°C
4 PULSE TEST
8
7
3
6.5
2
6
5.75
1
VGS = 5.5 V
0
0
1
2
3
4
DRAIN-SOURCE VOLTAGE
5
VDS
0
0
6
8
(V)
16
DRAIN-SOURCE VOLTAGE
COMMON SOURCE
VDS = 20 V
PULSE TEST
DRAIN-SOURCE VOLTAGE
(A)
DRAIN CURRENT ID
4
3
2
25
Tc = −55 °C
100
1
0
0
2
4
6
GATE-SOURCE VOLTAGE
8
VGS
10
10
(V)
COMMON SOURCE
Tc = 25°C
PULSE TEST
8
6
ID = 2.5 A
4
1.3
2
0.7
0
0
4
8
12
GATE-SOURCE VOLTAGE
(V)
⎪Yfs⎪ – ID
16
VGS
20
(V)
RDS (ON) – ID
10
100
COMMON SOURCE
VDS = 10 V
PULSE TEST
Tc = −55 °C
1
0.1
0.1
DRAIN-SOURCE ON RESISTANCE
RDS (ON) (Ω)
FORWARD TRANSFER ADMITTANCE
⎪Yfs⎪ (S)
VDS
40
VDS – VGS
VDS (V)
ID – VGS
5
32
24
25
100
1
DRAIN CURRENT ID
COMMON SOURCE
Tc = 25°C
PULSE TEST
10
VGS = 10, 15 V
1
0.1
0.1
10
(A)
1
DRAIN CURRENT ID
3
10
(A)
2013-11-01
TK3A60DA
RDS (ON) – Tc
IDR – VDS
COMMON SOURCE
VGS = 10 V
PULSE TEST
2.5
4.2
1.3
ID = 0.7 A
2.8
1.4
COMMON SOURCE
Tc = 25°C
PULSE TEST
10
10
5
1
3
−40
0
40
80
CASE TEMPERATURE
120
Tc
0.1
0
160
(°C)
−0.3
CAPACITANCE – VDS
GATE THRESHOLD VOLTAGE
Vth (V)
(V)
100
Coss
10
COMMON SOURCE
VGS = 0 V
f = 1 MHz
Tc = 25°C
Crss
1
10
3
2
COMMON SOURCE
1 VDS = 10 V
ID = 1 mA
PULSE TEST
0
−80
100
VDS
4
(V)
−40
VDS (V)
DRAIN-SOURCE VOLTAGE
40
30
20
10
CASE TEMPERATURE
80
120
Tc
160
(°C)
DYNAMIC INPUT / OUTPUT
CHARACTERISTICS
50
80
40
CASE TEMPERATURE
PD – Tc
40
0
120
Tc
160
(°C)
500
20
VDS
400
VDD = 100 V
300
VGS
100
0
4
8
TOTAL GATE CHARGE
4
12
400
200
0
16
200
8
COMMON SOURCE
ID = 2.5 A
Tc = 25°C
4
PULSE TEST
0
16
12
Qg
(V)
(pF)
C
CAPACITANCE
VDS
Vth – Tc
Ciss
DRAIN-SOURCE VOLTAGE
DRAIN POWER DISSIPATION
PD (W)
−1.5
−1.2
5
1000
0
0
−0.9
−0.6
DRAIN-SOURCE VOLTAGE
10000
1
0.1
VGS = 0 V
1
VGS
0
−80
GATE-SOURCE VOLTAGE
5.6
100
DRAIN REVERSE CURRENT
IDR (A)
DRAIN-SOURCE ON RESISTANCE
RDS (ON) ( Ω)
7
(nC)
2013-11-01
TK3A60DA
NORMALIZED TRANSIENT THERMAL
IMPEDANCE rth (t)/Rth (ch-c)
rth – tw
10
1
Duty=0.5
0.2
0.1
0.1
0.05
PDM
0.02
SINGLE PULSE
0.01
t
T
0.01
Duty = t/T
Rth (ch-c) = 4.17 °C/W
0.001
10μ
100μ
1m
10m
PULSE WIDTH
100m
1
tw (s)
EAS – Tch
SAFE OPERATING AREA
100
200
ID max (pulsed) *
100 μs *
ID
ID max (continuous)
1 ms *
1
DRAIN CURRENT
AVALANCHE ENERGY
EAS (mJ)
(A)
10
DC operation
Tc = 25°C
0.1
160
120
80
40
0
25
*: SINGLE NONREPETITIVE
0.01
10
PULSE Tc = 25°C
50
75
VDSS max
1
125
150
CHANNEL TEMPERATURE (INITIAL)
Tch(°C)
CURVES MUST BE DERATED
LINEARLY WITH INCREASE
IN TEMPERATURE.
0.001
0.1
100
10
DRAIN-SOURCE VOLTAGE
100
VDS
15 V
1000
(V)
BVDSS
IAR
−15 V
VDD
TEST CIRCUIT
RG = 25 Ω
VDD = 90 V, L = 50 mH
5
VDS
WAVEFORM
Ε AS =
⎛
⎞
1
B VDSS
⎟
⋅ L ⋅ I2 ⋅ ⎜
⎜B
⎟
2
−
V
VDSS
DD
⎝
⎠
2013-11-01
TK3A60DA
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively "Product") without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the
Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of
all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes
for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the
instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their
own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such
design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,
diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating
parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR
APPLICATIONS.
• PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH
MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without
limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for
automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions,
safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE
PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your
TOSHIBA sales representative.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the
U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited
except in compliance with all applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES
OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.
6
2013-11-01
