TL21W02-L1T34

TENTATIVE TL21W02-L1(T34 TL21W02-L1(T34 ・本資料は、製品の紹介を目的とした技術検討資料です。最終仕様段階で特性内容 の変更を伴う場合もあります。製品設計を行う場合は、営業部門に最終仕様を ご確認頂けます様お願い致します。 ・本資料の第三者への開示は、行わないようお願い致します。 ・This material is technological examination material to aim at the product introduction. The change in the content of the characteristic might be accompanied at the final specification process. The final specification will be able to be gotten in the brokerage department when the product is designed and to get the confirmation. ・Please do not open this material to the third person. Marktech Optoelectronics For part availability and ordering information please call Toll Free: 800.984.5337 Website: www.marktechopto.com | Email: info@marktechopto.com WL-0755 1 2011-04-11 TENTATIVE TOSHIBA LED lamps TL21W02-L1(T34 TL21W02-L1(T34 ○ Surface-mount devices • • • • • • 2.1 (L) mm × 2.5 (W) mm × 0.65 (H ) mm size High luminous flux LED: 42 lm(typ.) @IF=150 mA Color: white (3000K) High Color Rendering Index : Ra=85 (Typ.) Reflow-soldering is available Applications : general lighting and etc. 0.65 2.1 2.5 Unit: mm Color and Material Part Number TL21W02-L1 Color White (3000K) Material InGaN (0.3) Absolute Maximum Ratings (Ta = 25°C) (Note.1) Characteristics Forward Current (Note.2) Pulse current (Note.3) Power Dissipation Operating Temperature Storage Temperature Junction Temperature Symbol IF IFP PD Topr Tstg Tj Rating (180) (300) 0.76 −40 to 100 −40 to 100 120 Unit mA mA W °C °C °C 1 1.55 2 0.45 1. 2. CATHODE ANODE ― ― 4-2J1 JEDEC JEITA TOSHIBA Weight: **** g (typ.) Note 1: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/”Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: The junction-to-ambient thermal resistance, Rth(j-a), should be kept below 70℃/W so that the TL21W02-L1(T34 is not exposed to a condition beyond the absolute maximum ratings. Rth(j-a): Thermal resistance from the LED junction to ambient temperature 200 (mA) IF – Ta 180 160 140 120 100 80 60 40 20 0 0 Rth(j-a)=70℃/W Allowable forward current IF 20 40 60 80 100 Ambient temperature Ta (°C) 120 Note 3: Pulse width 10ms, Duty 1/10 WL-0755 Marktech Optoelectronics 2 For part availability and ordering information please call Toll Free: 800.984.5337 Website: www.marktechopto.com | Email: info@marktechopto.com 2011-04-11 1.8 TENTATIVE Electrical Characteristics (Ta = 25°C) Characteristics Forward Voltage (Note 4) Reverse Voltage Thermal Resistance (Note 5) Symbol VF VR Rth(j-s) Test condition IF =150 mA IR = 1 m A IF = 150 mA Min (2.9) ⎯ ⎯ TL21W02-L1(T34 Typ. (3.25) 0.75 (20) Max (3.8) ⎯ ⎯ Unit V V °C/W Note 4: VF rank classification The specification on the following table is used for VF classification of LEDs in Toshiba facility. Each reel includes the same rank LEDs. Let the delivery ratio of each rank be unquestioned. Ta=25°C Tolerance: +/-0.1V Part Number Min TL21W02-L1(T34 1 2 3 Unit (2.9) 2.9 3.2 3.5 Forward Voltage Typ. (3.25) ⎯ ⎯ ⎯ V VF IF Max (3.8) 3.2 3.5 3.8 150 mA Note 5: Rth(j-s): Thermal resistance from the LED junction to solder point. Optical Characteristics (Ta = 25°C) Characteristics Chromaticity Color temperature Luminous flux (Note 7) Color rendering index Symbol Cx Cy CCT ΦV Ra Test condition IF = 150 mA IF = 150 mA IF = 150 mA IF = 150 mA IF = 150 mA ⎯ (30.3) 80 Min Typ. (Note 6) (Note 6) 3000 (42) 85 ⎯ (60.5) ⎯ Max Unit ⎯ ⎯ K lm ⎯ Note 6: Chromaticity classification The product is classified at the following chromaticity coordinate groups. Each reel includes the same rank LEDs. Let the delivery ratio of each rank be unquestioned. Test conditions: IF=150 mA, Ta=25°C Tolerance: ±0.01 0.45 0.44 0.43 0.42 Cy 0.41 0.40 0.39 0.38 0.37 0.36 0.39 0.40 0.41 0.42 0.43 0.44 0.45 0.46 0.47 0.48 Cx 7A 7B 7D 7C 3220K 3000K 2870K Cx Cy 7A 7B 7C ANSI C78.377 7D 0.4147 0.4221 0.4342 0.4259 0.4221 0.4299 0.443 0.4342 0.4342 0.4430 0.4562 0.4465 0.4259 0.4342 0.4465 0.4373 0.3814 0.3984 0.4028 0.3853 0.3984 0.4165 0.4212 0.4028 0.4028 0.4212 0.426 0.4071 0.3853 0.4028 0.4071 0.3893 WL-0755 3 2011-04-11 TENTATIVE TL21W02-L1(T34 Note 7: ΦV rank classification The specification on the following table is used for F classification of LEDs in Toshiba facility. Each reel includes the same rank LEDs. Let the delivery ratio of each rank be unquestioned. Ta=25°C Tolerance: +/-10% Part Number Min TL21W02-L1(T34 C16 C17 C18 C19 Unit (30.3) 30.3 36.0 42.8 51.0 Luminous flux Typ. (42) ⎯ ⎯ ⎯ ⎯ lm ΦV Max (60.5) 36.0 42.8 51.0 60.5 mA 150 IF Note 8: Color Rendering Index Measurement tolerance : +/- 5 Cautions • The product is sensitive to electrostatic and care must be fully taken when handling products. Particularly in the case that an over-voltage shall be applied, the overflowed energy may cause damage to or possibly result in destruction of the product. Users shall take absolutely secure countermeasures against electrostatic and surge when handling the product. • This product is designed as a general display light source usage, and it has applied the measurement standard that matched with the sensitivity of human's eyes. Therefore, it is not intended for usage of functional application (ex. Light source for sensor, optical communication and etc) except general display light source. • Please note the handling of products during evaluation. 1. Please do not apply pressure to the upper surface of the product with finger, tweezers, and others. Failure of product to light up may occur due to package deformation, wire deformation and/or disconnection. 2. Should tweezers be used in product handling, one with flat surfaces is recommended. 3. Please handle the product widthwise. 4. Please do not drop the product. There is a possibility for package transformation etc. to occur when the product is dropped. 5. Please do not stack the Printed Circuit Boards on which the product is mounted to prevent damages to product surface. Also, please note not to damage the surface of the product with cushioning material etc. Surface damage to the product may influence their optical characteristics. WL-0755 4 2011-04-11 TENTATIVE Packaging TL21W02-L1(T34 This LED device is packed in an aluminum envelope with a silica gel and a moisture indicator to avoid moisture absorption. The optical characteristics of the device may be affected by exposure to moisture in the air before soldering and the device should therefore be stored under the following conditions: 1. This moisture proof bag may be stored unopened within 12 months at the following conditions. Temperature: 5°C~30°C Humidity: 90% (max) 2. After opening the moisture proof bag, the device should be assembled within 168 hours in an environment of 5°C to 30°C/60% RH or below. 3. If upon opening, the moisture indicator card shows humidity 30% or above (Color of indication changes to pink) or the expiration date has passed, the device should be baked in taping with reel. After baking, use the baked device within 72 hours, but perform baking only once. Baking conditions: 60±5°C, for 24 to 48 hours. Expiration date: 12 months from sealing date, which is imprinted on the label affixed. 4. Repeated baking can cause the peeling strength of the taping to change, then leads to trouble in mounting. 5. If the packing material of laminate would be broken, the hermeticity would deteriorate. Therefore, do not throw or drop the packed devices. Mounting Method Soldering • Reflow soldering (example) Temperature profile for Pb soldering (example) 10 s max (*) 240°C max Package surface temperature (°C) Temperature profile for Pb-free soldering (example) 5 s max(*) 260°C max Package surface temperature (°C) (*) (*) 140~160°C 4°C/s max max(*) 4°C/s max(*) (*) 4°C/s max(*) max(*) 150~180°C 230°C (*) 4°C/s max 60~120 s Time max(*) 30~50s max(*) (s) 60~120 s max(*) Time (s) • • • • • The product is evaluated using above reflow soldering conditions. No additional test is performed exceed the condition (i.e. the condition more than (*)MAX values) as a evaluation. Please perform reflow soldering under the above conditions. Please perform the first reflow soldering with reference to the above temperature profile and within 168 h of opening the package. Second reflow soldering In case of second reflow soldering should be performed within 168 h of the first reflow under the above conditions. Storage conditions before the second reflow soldering: 30°C, 60% RH (max) When any soldering corrections are made manually,a hot-plate should be used and do not use soldering iron. (only once at each soldering point) Do not perform wave soldering. Land pattern dimensions for reference only 0.3 Unit : mm 1.55 0.45 1.8 WL-0755 5 2011-04-11 TENTATIVE Cleaning TL21W02-L1(T34 When cleaning is required after soldering, Toshiba recommends the following cleaning solvents. It is confirmed that these solvents have no effect on semiconductor devices in our dipping test (under the recommended conditions). In selecting the one for your actual usage, please perform sufficient review on washing condition, using condition and etc. ASAHI CLEAN AK-225AES KAO CLEAN TROUGH 750HS PINE ALPHA ST-100S : (made by ASAHI GLASS) : (made by KAO) : (made by ARAKAWA CHEMICAL) Precautions when Mounting Do not apply force to the plastic part of the LED under high-temperature conditions. To avoid damaging the LED plastic, do not apply friction using a hard material. When installing the PCB in a product, ensure that the device does not come into contact with other components. Tape Specifications 1. Product number format The type of package used for shipment is denoted by a symbol suffix after the product number. The method of classification is as below. (this method, however does not apply to products whose electrical characteristics differ from standard Toshiba specifications) (1) Tape Type: T34 (8-mm pitch) (2) Example TL21W02-L1 (T34 Tape type Toshiba product No. 2. Tape dimensions Unit: mm Symbol D E P0 t F D1 Dimension 1.5 1.75 4.0 0.3 3.5 1.1 Tolerance +0.1/−0 ±0.1 ±0.1 ±0.05 ±0.05 ±0.1 P0 D P2 E F W B0 極性 A0 P D1 t Symbol P2 W P A0 B0 K0 Dimension 2.0 8.0 8.0 (2.4) (2.8) 0.8 Tolerance ±0.05 ±0.2 ±0.1 ±0.1 ±0.1 ±0.05 K0 WL-0755 6 2011-04-11 TENTATIVE 3. Reel dimensions TL21W02-L1(T34 Unit: mm 9 +1/−0 11.4 ± 1.0 +0 180 −4 2 ± 0.5 4. Leader and trailer sections of tape 40 mm or more 40 mm or more Leading part: 190 mm (min) φ13 φ60 φ44 WL-0755 7 2011-04-11 TENTATIVE 5. Packing form (1) Packing quantity Reel Carton 1,000 pcs 5,000 pcs TL21W02-L1(T34 (2) Packing form: Each reel is sealed in an aluminum pack with silica gel. 6. Label format (1) Example : TL21W02-L1(T34 P/N: TYPE ADDC 1) xxxxxx 3) (xxxxx) 6) xxxxxxxxxx 7) Use TOSHIBA TL21W02-L1(T34 xxx 2) xxxxxxxx Q’TY 4) xxx 1,000 pcs 5)xxxx under 5-30degC/60%RH within 168h [[G]]/RoHS COMPATIBLE *Y380xxxxxxxxxxxxxxxxxx* SEALED: DIFFUSED IN xxxxx ASSEMBLED IN xxxxx (1)-1 Contents about Note section (Each example means the contents are different for each lot.) Information for customers use 1) Lot code Example: 2707C2B 2) Key code Example: 12345 3) Rank symbol Example: 7AC172 Example: Information for Toshiba use 4) Management code 015 32G 5) Packing quantity Example: 1000 6) Product information (refer to section (1)-2) Exxxx 7) Storage condition after opening Use under 5-30 degC/60%RH within 168h (1)-2 Explanations for “ADDC” and “Product information” ADDC Product information Assembled in domestic : (L1 xxx Assembled in overseas : (L2 xxx (2) Label location • Reel • Carton Tape feel direction Label position Label position • The aluminum package in which the reel is supplied also has the label attached to center of one side. WL-0755 8 2011-04-11 TENTATIVE RESTRICTIONS ON PRODUCT USE TL21W02-L1(T34 • Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively “Product”) without notice. • This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission. • Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. • Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. • Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. • Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. • ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. • Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. • Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. WL-0755 9 2011-04-11