TLN233

TLN233(F) TOSHIBA Infrared LED GaAℓAs Infrared Emitter TLN233(F) Lead(Pb)-Free Infrared LED for Space-Optical-Transmission • • • • • High radiant intensity: 80 mW/sr (typ.) at IF = 50 mA Half-angle value: θ1/2 = ±13° (typ.) A light source for remote control Wireless AV-signal transmission purposes High-speed data transmission purposes Unit: mm Absolute Maximum Ratings (Ta = 25°C) Characteristics Forward current Pulse forward current Power dissipation Reverse voltage Operating temperature range Storage temperature range Soldering temperature (5 s), (Note 2) Symbol IF IFP PD VR Topr Tstg Tsol Rating 100 1000 (Note 1) 200 4 −25~85 −30~100 260 Unit mA mA mW V °C °C °C TOSHIBA Weight: 0.3 g (typ.) 4-5V3 Pin Connection Note: Using continuously under heavy loads (e.g. the application of high 1. Anode 1 2 2. Cathode temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: f = 100 kHz, duty = 1% Note 2: Soldering must be performed under the stopper. 1 2007-10-01 TLN233(F) Optical and Electrical Characteristics (Ta = 25°C) Characteristics Forward voltage Reverse current Radiant intensity Radiant power Cut-off frequency Peak emission wavelength Half-angle value Symbol VF IR IE PO fc λP θ 1 2 Test Condition IF = 100 mA VR = 4 V IF = 50 mA IF = 50 mA IF = 50 mA + 5 mAP-P IF = 50 mA IF = 50 mA (Note 3) Min ⎯ ⎯ 46 ⎯ ⎯ ⎯ ⎯ Typ. 1.6 ⎯ 80 30 15 870 ±13 Max 2.0 60 ⎯ ⎯ ⎯ ⎯ ⎯ Unit V μA mW/sr mW MHz nm ° Note 3: This is the frequency when modulation light power decreases by 3 dB from 1 MHz. Handling Precautions • • • Soldering must be performed under the stopper. When forming the leads, bend each lead at least 5 mm from the package body. Soldering must be performed after the leads have been formed. The radiant intensity decreases over time due to current flowing in the infrared LED. When designing circuits, take into account the change in radiant intensity over time. The change in radiant intensity is equal to the reciprocal of the change in LED infrared optical output: IE (t) P o (t) . = IE (0) P o (0) 2 2007-10-01 TLN233(F) IF – Ta 120 100 75°C 100 IF – V F (typ.) IF (mA) (mA) −25°C 10 85°C 0°C Ta = 25°C Allowable forward current 80 60 Forward current IF 1 50°C 40 0.1 20 0 0 20 40 60 80 100 0.01 0.8 1 1.2 1.4 1.6 1.8 2 Ambient temperature Ta (°C) Forward voltage VF (V) VF – Ta 1.8 1.7 (typ.) 1000 IFP – VFP (typ.) Pulse forward current IFP (mA) (V) 100 mA 1.6 1.5 1.4 1.3 1.2 1.1 1 −50 IF = 10 mA 70 mA 50 mA 30 mA 300 Forward voltage VF 100 30 10 Pulse width < 100 μs = Repetitive frequency = 100 Hz Ta = 25°C 3 −25 0 25 50 75 100 1 0 1 2 3 4 5 Ambient temperature Ta (°C) Pulse forward voltage VFP (V) IFP – Pw 10000 1.2 Ta = 25°C 3000 f = 100 Hz 200 Hz 300 500 Hz 1 kHz 2 kHz 100 5 kHz 10 kHz 30 1.0 Relative IE – IFP Pulse width = 1 ms Duty = 10% Ta = 25°C Allowable pulse forward current IFP (mA) 1000 Relative radiant intensity 10000 0.8 0.6 0.4 0.2 10 1 10 100 1000 0 0 200 400 600 800 1000 1200 Pulse width Pw (μs) Pulse forward current IFP (mA) 3 2007-10-01 TLN233(F) Wavelength characteristic 1 IF = 50 mA 0.8 10 IF = 50 mA Relative IE – Ta (typ.) 0.6 Relative radiant intensity Relative power intensity 3 1 0.4 0.2 0.3 0 700 740 780 820 860 900 940 980 0.1 −50 −25 0 25 50 75 100 Wavelength λ (nm) Ambient temperature Ta (°C) Radiation pattern (typ.) Ta = 25°C 30° 40° 50° 60° 70° 80° 90° 20° 10° 0° 10° 20° 30° 40° 50° 60° 70° 80° 90° 1.0 0 0.2 0.4 0.6 0.8 Relative radiant power 4 2007-10-01 TLN233(F) RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • GaAs(Gallium Arsenide) is used in this product. The dust or vapor is harmful to the human body. Do not break, cut, crush or dissolve chemically. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 5 2007-10-01