TLP176D(F)

TLP176D TOSHIBA Photocoupler IRED & Photo-MOSFET TLP176D Modem  Fax Card PBX Telecommunication Unit: mm The TOSHIBA TLP176D consists of an infrared emitting diode optically coupled to a photo-MOSFET in a SOP, which is suitable for surface mount assembly. The TLP176D is suitable for modem and PBX applications which require space savings.  SOP 4 pin (2.54SOP4): 1-form-A  Peak off-state voltage: 200 V (min)  Trigger LED current: 3 mA (max)  On-state current: 200 mA (max)  On-state resistance: 8 Ω (max)  Isolation voltage: 1500 Vrms (min)  UL-recognized: UL 1577, File No.E67349  cUL-recognized: CSA Component Acceptance Service No.5A JEDEC ― JEITA ― TOSHIBA 11-5H1S Weight: 0.1 g (typ.) File No.E67349  VDE-approved: EN 60747-5-5 (Note 1) Note 1: When a VDE approved type is needed, please designate the Option(V4). Pin Configuration (top view) 1 4 2 3 1: Anode 2: Cathode 3: Drain 4: Drain Internal Circuit 1 4 2 3 Start of commercial production © 2019-2022 Toshiba Electronic Devices & Storage Corporation 1 1998-03 2022-06-17 TLP176D Absolute Maximum Ratings (Ta = 25°C) Characteristics Symbol Rating Unit IF 50 mA ΔIF/°C −0.5 mA/°C Pulse forward current (100 μs pulse, 100 pps) IFP 1 A Reverse voltage VR 5 V Diode power dissipation PD 50 mW ΔPD /°C -0.5 mW/°C Tj 125 °C VOFF 200 V ION 200 mA ΔION/°C −2.0 mA/°C PO 180 mW ΔPO / °C −18 mW / °C Tj 125 °C Storage temperature range Tstg −55 to 125 °C Operating temperature range Topr −40 to 85 °C Lead soldering temperature (10 s) Tsol 260 °C BVS 1500 Vrms Forward current Forward current derating (Ta ≥ 25°C) LED Diode power dissipation derating (Ta ≥25°C) Junction temperature Off-state output terminal voltage On-state current Detector On-state RMS current derating (Ta ≥ 25°C) Output power dissipation Output power dissipation derating (Ta ≥ 25°C) Junction temperature Isolation voltage (AC, 60 s, R.H. ≤ 60 %) (Note1) Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note1: Device considered a two-terminal device: pins1 and 2 shorted together and pins 3 and 4 shorted together. Recommended Operating Conditions Characteristics Symbol Min Typ. Max Unit Supply voltage VDD ― 150 200 V Forward current IF 5 7.5 25 mA On-state current ION ― ― 130 mA Operating temperature Topr −20 ― 65 °C Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the device. Additionally, each item is an independent guideline respectively. In developing designs using this product, please confirm specified characteristics shown in this document. © 2019-2022 Toshiba Electronic Devices & Storage Corporation 2 2022-06-17 TLP176D Individual Electrical Characteristics (Ta = 25°C) Characteristics LED Detector Symbol Test Condition Min Typ. Max Unit Forward voltage VF IF = 10 mA 1.0 1.15 1.3 V Reverse current IR VR = 5 V ― ― 10 μA Capacitance between terminals CT VF = 0 V, f = 1 MHz ― 30 ― ― ― 1 ― 100 ― Min Typ. Max Unit ― 1 3 mA Off-state current IOFF VOFF = 200 V Capacitance between terminals COFF V = 0 V, f = 1 MHz pF μA pF Coupled Electrical Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Trigger LED current IFT ION = 200 mA On-state resistance RON ION = 200 mA, IF = 5 mA ― 5 8 Ω Return LED current IFC IOFF = 100 μA 0.1 ― ― mA Min Typ. Max Unit ― 0.8 ― pF 1014 ― Ω 1500 ― ― Vrms Min Typ. Max Unit ― 0.6 1.5 ms ― 0.1 1.0 ms Isolation Characteristics (Ta = 25°C) Characteristics Capacitance input to output Isolation resistance Symbol CS VS = 0 V, f = 1 MHz RS Isolation voltage Test Condition 5 VS = 500 V, R.H. ≤ 60 % BVS AC, 60 s 1010 Switching Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Turn-on time tON RL = 200 Ω VDD = 20 V, IF = 5 mA (Note) Turn-off time tOFF RL = 200 Ω VDD = 20 V, IF = 5 mA (Note) Note: Switching time test circuit IF 1 4 2 3 RL VDD IF VOUT 90% VOUT 10% tON © 2019-2022 Toshiba Electronic Devices & Storage Corporation 3 tOFF 2022-06-17 TLP176D IF – Ta ION – Ta (mA) 80 300 ION 350 250 MOSFET ON-state current Allowable forward current IF (mA) 100 60 40 20 0 −20 0 20 60 40 Ambient temperature 80 200 150 100 50 0 −20 100 0 Ta (°C) IF – VF (mA) Ta = 25°C IF = 5 mA 200 ION 30 10 MOSFET ON-state current Allowable forward current IF (mA) 100 ION – VON 300 Ta = 25°C 3 1 0.3 0.1 0.6 1.0 0.8 1.2 Forward voltage 1.6 1.4 VF 100 0 −100 −200 −300 −1 1.8 (V) RON – Ta Relative trigger LED current IFT/IFT (Ta = 25°C) t1s (Ω) 6 4 2 0 1 (V) ION = 200 mA t1s IF = 5 mA 0 −20 0.5 IFT – Ta 5 ION = 200 mA 8 0 −0.5 MOSFET ON-state voltage VON 10 RON 80 60 Ambient temperature Ta (°C) 100 MOSFET ON-state resistance 40 20 20 40 60 80 4 3 2 1 0 −40 100 Ambient temperature Ta (°C) −20 0 20 40 60 80 100 Ambient temperature Ta (°C) NOTE: The above characteristics curves are presented for reference only and not guaranteed by production test, unless otherwise noted. © 2019-2022 Toshiba Electronic Devices & Storage Corporation 4 2022-06-17 TLP176D tON, tOFF – IF 3000 Ta = 25°C VDD = 20 V RL = 200 Ω (μs) tON, tOFF 300 100 tOFF 30 10 1 3 5 10 50 30 Forward current IE 100 VDD = 20 V RL = 200 Ω 1000 Switching time tON, tOFF (μs) tON Switching time tON, tOFF – Ta 3000 1000 300 100 30 10 −40 300 500 (mA) IF = 5 mA −20 0 20 40 60 80 100 Ambient temperature Ta (°C) IOFF – Ta MOSFET OFF-state current IOFF (mA) 100 VOFF = 200 V 30 10 3 1 −20 0 20 40 60 80 100 120 Ambient temperature Ta (°C) NOTE: The above characteristics curves are presented for reference only and not guaranteed by production test, unless otherwise noted. © 2019-2022 Toshiba Electronic Devices & Storage Corporation 5 2022-06-17 TLP176D RESTRICTIONS ON PRODUCT USE Toshiba Corporation and its subsidiaries and affiliates are collectively referred to as “TOSHIBA”. Hardware, software and systems described in this document are collectively referred to as “Product”.  TOSHIBA reserves the right to make changes to the information in this document and related Product without notice.  This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.  Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.  PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT ("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, lifesaving and/or life supporting medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, and devices related to power plant. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales representative or contact us via our website.  Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.  Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations.  The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.  ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.  GaAs (Gallium Arsenide) is used in Product. GaAs is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. Handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose GaAs in Product.  Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations.  Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS. https://toshiba.semicon-storage.com/ © 2019-2022 Toshiba Electronic Devices & Storage Corporation 6 2022-06-17