TLP3407SRL(TP,E

TLP3407SRL Photocouplers Photorelay AR Y TLP3407SRL ATE (Automatic Test Equipment) • Measuring Instruments • High-Speed Logic IC Testers • High-Speed Memory Testers uc Probe Cards • rod • ts. 1. Applications rp 2. General ou The TOSHIBA TLP3407SRL photorelay consists of a photo MOSFET optically coupled to an infrared light emitting gy diode. It is housed in a S-VSON4T package. The TLP3407SRL features a very small on-resistance and on/off 3. Features Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig nin switching ofcurrent as high as 1 A, making it ideal for switching applications in high-speed testers. S-VSON4T: 2.0 (L) mm × 1.45 (W) mm × 1.3 (H) mm (2) Normally opened (1-Form-A) (3) OFF-state output terminal voltage: 60 V (min) (4) Operating voltage: 1.6 V (max) (5) ON-state current: 1 A (max) IN (1) (6) ON-state resistance: 0.2 Ω (typ.), 0.3 Ω (max) (7) Isolation voltage: 500 Vrms (min) PR EL IM 4. Packaging and Pin Assignment 11-2E2 ©2018-2019 Toshiba Electronic Devices & Storage Corporation 1: Anode 2: Cathode 3: Drain 4: Drain Start of commercial production 1 2019-02 2019-01-09 Rev.0.3 TLP3407SRL AR Y 5. Internal Circuit Output power dissipation derating Junction temperature Operating temperature uc rod gy mW/ 125  VOFF 60 V ION 1 A ∆ION/∆Ta -10 mA/ IONP 3 A PO 240 mW (Ta ≥ 25 ) ∆PO/∆Ta -2.4 mW/ Tj 125  Tstg -40 to 125  Topr -40 to 110 (10 s) Tsol 260 AC, 60 s, R.H. ≤ 60 % BVS (Note 1) 500 Vrms Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: This device is considered as a two-terminal device: Pins 1 and 2 are shorted together, and pins 3 and 4 are shorted together. PR EL Note: -0.5 (Ta ≥ 25 ) Lead soldering temperature Isolation voltage mW (t = 100 ms, Duty = 1/10) IM Common Storage temperature 50 Tj IN Output power dissipation ∆PD/∆Ta Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig (Ta ≥ 25 ) Detector OFF-state output terminal voltage ON-state current (pulsed) 6 PD Input power dissipation derating ON-state current derating V 3 VR Input power dissipation ON-state current Unit VIN Input reverse voltage Junction temperature Rating ou Applied input forward voltage Note nin LED Symbol rp Characteristics ts. 6. Absolute Maximum Ratings (Note) (Unless otherwise specified, Ta = 25 ) Note: This device is sensitive to electrostatic discharge (ESD). Extreme ESD conditions should be guarded against by using proper antistatic precautions for the worktable, operator, solder iron, soldering equipment and so on. 7. Recommended Operating Conditions (Note) Characteristics Supply voltage Applied input forward voltage ON-state current Symbol Operating temperature Note: Note Min Typ. Max Unit VDD   48 V VIN  1.8 3 V ION   1 A Topr -20  100  The recommended operating conditions are given as a design guide necessary to obtain the intended performance of the device. Each parameter is an independent value. When creating a system design using this device, the electrical characteristics specified in this data sheet should also be considered. ©2018-2019 Toshiba Electronic Devices & Storage Corporation 2 2019-01-09 Rev.0.3 TLP3407SRL 8. Electrical Characteristics (Unless otherwise specified, Ta = 25 ) Characteristics Note Test Condition Min Typ. Max Unit Input reverse current IR VR = 5 V   10 µA Input capacitance Ct V = 0 V, f = 1 MHz  30  pF VOFF = 60 V   1 µA VOFF = 50 V   1 nA V = 0 V, f = 1 MHz, t < 1 s  80 150 pF Detector OFF-state current IOFF Output capacitance COFF AR Y LED Symbol Test Condition Min Typ. VFON ION = 100 mA  1.2 Turn-off voltage VFOFF IOFF = 10 µA 0.8 1.1 ION = 1 A, VIN = 2 V, t < 1 s  0.2 RON Isolation voltage CS RS BVS Note Test Condition (Note 1) VS = 0 V, f = 1 MHz IN Total capacitance (input to output) Isolation resistance Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig Symbol (Note 1) VS = 500 V, R.H. ≤ 60 % (Note 1) AC, 60 s 1.6 V  V 0.3 Ω nin 10. Isolation Characteristics (Unless otherwise specified, Ta = 25 ) Characteristics Unit gy ON-state resistance Max ou Operating voltage uc Note rod Symbol rp Characteristics ts. 9. Coupled Electrical Characteristics (Unless otherwise specified, Ta = 25 ) Min Typ. Max Unit  1  pF  1014  Ω 500   Vrms Note 1: This device is considered as a two-terminal device: Pins 1 and 2 are shorted together, and pins 3 and 4 are shorted together. 11. Switching Characteristics (Unless otherwise specified, Ta = 25 ) Turn-on time Note Test Condition tON tOFF See Fig. 11.1. RL = 200 Ω, VDD = 20 V, VIN = 2 V Min Typ. Max Unit  0.4 1 ms  0.1 0.2 PR EL Turn-off time Symbol IM Characteristics Fig. 11.1 Switching Time Test Circuit and Waveform ©2018-2019 Toshiba Electronic Devices & Storage Corporation 3 2019-01-09 Rev.0.3 TLP3407SRL gy ou rp rod uc ts. AR Y 12. Characteristics Curves (Note) Fig. 12.2 ION - VON IM IN Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig nin Fig. 12.1 ION - Ta PR EL Fig. 12.3 RON - Ta Fig. 12.5 tON, tOFF - VIN ©2018-2019 Toshiba Electronic Devices & Storage Corporation Fig. 12.4 VFON - Ta Fig. 12.6 tON, tOFF - Ta 4 2019-01-09 Rev.0.3 rp rod uc ts. AR Y TLP3407SRL Fig. 12.8 IOFF - Ta IM IN Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig nin gy ou Fig. 12.7 IOFF - VOFF Fig. 12.9 COFF/COFF(0 V) - VOFF The above characteristics curves are presented for reference only and not guaranteed by production test, unless otherwise noted. PR EL Note: ©2018-2019 Toshiba Electronic Devices & Storage Corporation 5 2019-01-09 Rev.0.3 TLP3407SRL 13. Soldering and Storage 13.1. Precautions for Soldering The soldering temperature should be controlled as closely as possible to the conditions shown below. When using soldering reflow AR Y • (See the figure shown below, which is based on the package surface temperature.) Reflow soldering may be performed up to twice. The first reflow soldering should be performed within 168 hours after opening the moisture-proof packaging. When using soldering Iron IN • Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig nin gy ou rp rod uc ts. The second reflow soldering must be performed within 168 hours of the first reflow. Complete soldering within 10 seconds for lead temperature not exceeding 260 . PR EL IM Heating by soldering iron must be done only once per lead. ©2018-2019 Toshiba Electronic Devices & Storage Corporation 6 2019-01-09 Rev.0.3 TLP3407SRL 13.2. Precautions for General Storage • Avoid storage locations where devices may be exposed to moisture or direct sunlight. • Do not store the products in locations with poisonous gases (especially corrosive gases) or in dusty conditions. Store the products in locations with minimal temperature fluctuations. Rapid temperature changes during AR Y • storage can cause condensation, resulting in lead oxidation or corrosion, which will deteriorate the solderability of the leads. • Do not allow loads to be applied directly to devices while they are in storage. • If devices have been stored for more than two years under normal storage conditions, it is recommended ts. that you check the leads for ease of soldering prior to use. Follow the precautions printed on the packing label of the device for transportation and storage. • Thermal stress may cause a crack in surface-mount products during surface-mount assembly if they have rod uc • rp absorbed atmospheric moisture. To prevent a crack, please observe the following precautions. ou 1. Moisture-proof bags may be stored unopened for up to 12 months under the following conditions. gy Temperature: 5  to 30  nin Humidity: 90 % (max) Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig 2. After opening the moisture-proof bag, the devices should be assembled within 168 hours in an environment of 5  to 30 /70 %RH or below. IN 3. If, upon opening, the moisture indicator card shows a humidity of 30 % or above (i.e., has turned pink) or the expiration date has passed, the devices should be baked in tape and reel. After baking, use the baked devices within 72 hours, but perform baking only once. Baking conditions: 60±5 , for 64 to 72 hours. Expiration date: 12 months from the sealing date, which is imprinted on the label affixed. 4. Repeated baking can affect the peeling strength of taping and cause a trouble during mounting. Furthermore, protect the devices against static electricity for baking. IM 5. If the laminated packing material is broken, its hermeticity deteriorates. Therefore, do not throw or drop the packed devices. PR EL 6. When restoring devices after removal from their packing, use anti-static containers. ©2018-2019 Toshiba Electronic Devices & Storage Corporation 7 2019-01-09 Rev.0.3 gy nin rp ou ts. uc rod AR Y IN IM 15. Marking Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig PR EL TLP3407SRL 14. Land Pattern Dimensions (for reference only) ©2018-2019 Toshiba Electronic Devices & Storage Corporation 8 2019-01-09 Rev.0.3 TLP3407SRL 16. Embossed-Tape Packing (TP) Specification for Mini-Flat Photorelays 16.1. Applicable Package Product Type S-VSON4T Photorelay AR Y Package Name 16.2. Product Naming Conventions Type of package used for shipment is denoted by a symbol suffix after a part number. The method of classification ts. is as below. rod uc Example) TLP3407SRL(TP,E rp Part number: TLP3407SRL ou Tape type: TP Single empty cavity 6 devices (max) per reel IN Occurrences of 2 or more successive empty cavities Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig nin gy [[G]]/RoHS COMPATIBLE: E (Note 1) Note 1: Please contact your Toshiba sales representative for details on environmental information such as the product's RoHS compatibility. RoHS is the Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 16.3. Tape Dimensions Specification Tape Type Division TP  Packing Amount (A unit per reel) 2500 16.3.1. Orientation of Device in Relation to Direction of Feed PR EL IM Device orientation in the carrier cavities as shown in the following figure. Device Orientation 16.3.2. Empty Cavities Characteristics Criterion Remarks 0 device Within any given 40-mm section of tape, not including leader and trailer Not including leader and trailer 16.3.3. Tape Leader and Trailer The start end of the tape has 40 or more empty cavities. The hub end of the tape has 40 or more empty cavities and one-third empty turns only for a cover tape. ©2018-2019 Toshiba Electronic Devices & Storage Corporation 9 2019-01-09 Rev.0.3 TLP3407SRL 16.3.4. Tape Dimensions Remark A 1.6  gy Dimension Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig Symbol ou Tape Dimensions (unit: mm, tolerance: ±0.1) nin Table rp rod uc ts. AR Y Tape material: Plastic (for protection against static electricity) 2.25  3.5 Center line of embossed cavity and sprocket hole E 1.75 Distance between tape edge and sprocket hole center F 4.0 Cumulative error +0.2/-0.2 per 10 empty cavities holes G 4.0 Cumulative error +0.2/-0.2 per 10 sprocket holes K0 1.5 Internal space PR EL IM IN B D ©2018-2019 Toshiba Electronic Devices & Storage Corporation 10 2019-01-09 Rev.0.3 TLP3407SRL 16.3.5. Reel Specification IN Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig nin gy ou rp rod uc ts. AR Y Material: Plastic (for protection against static electricity) Table Symbol A B Dimension φ180 ± 3 φ60 ± 1 φ13 ± 0.5 E 2.0 ± 0.5 U 4.0 ± 0.5 IM C W1 9.0 ± 0.3 W2 11.4 ± 1.0 PR EL 16.4. Packing (Note) Reel Dimensions (unit: mm) 1 reel/carton (unit: mm) Note: Taping reel diameter: φ180 mm 16.5. Label Format The carton bears a label indicating the product number, the symbol representing classification of standard, the quantity, the lot number and the Toshiba company name. ©2018-2019 Toshiba Electronic Devices & Storage Corporation 11 2019-01-09 Rev.0.3 TLP3407SRL 16.6. Ordering Information When placing an order, please specify the part number, tape type and quantity as shown in the following example. AR Y Example) TLP3407SRL(TP,E 2500 pcs Part number: TLP3407SRL Tape type: TP [[G]]/RoHS COMPATIBLE: E (Note 1) PR EL IM IN Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig nin gy ou rp rod uc ts. Quantity (must be a multiple of 2500): 2500 pcs Note 1: Please contact your Toshiba sales representative for details on environmental information such as the product's RoHS compatibility. RoHS is the Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. ©2018-2019 Toshiba Electronic Devices & Storage Corporation 12 2019-01-09 Rev.0.3 Weight: 0.01 g (typ.) gy nin rp ou ts. uc rod AR Y IN Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig IM PR EL TLP3407SRL Package Dimensions Unit: mm Package Name(s) TOSHIBA: 11-2E2 ©2018-2019 Toshiba Electronic Devices & Storage Corporation 13 2019-01-09 Rev.0.3 TLP3407SRL RESTRICTIONS ON PRODUCT USE Toshiba Corporation and its subsidiaries and affiliates are collectively referred to as "TOSHIBA". Hardware, software and systems described in this document are collectively referred to as "Product". AR Y • TOSHIBA reserves the right to make changes to the information in this document and related Product without notice. • This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. nin gy ou rp rod uc ts. • Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. IN Do Ple not as de e c sig on n y tac ou ty rp ou rod r T uc os ts hib or a s sy ale ste s r ms ep ba res se en d o tat n ive the for inf up orm da at ted ion inf on orm th ati is do on cu be me for nt ed . es ig • PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT ("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, lifesaving and/or life supporting medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, and devices related to power plant. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales representative or contact us via our website. • Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. IM • Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. PR EL • ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. • GaAs (Gallium Arsenide) is used in Product. GaAs is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. Handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose GaAs in Product. • Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. • Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS. https://toshiba.semicon-storage.com/ ©2018-2019 Toshiba Electronic Devices & Storage Corporation 14 2019-01-09 Rev.0.3