TPC8014(TE12L,Q,M)

TPC8014 TOSHIBA Field Effect Transistor Silicon N Channel MOS Type (U-MOS III) TPC8014 Lithium Ion Battery Applications Portable Equipment Applications Notebook PC Applications • Unit: mm Small footprint due to small and thin package • Low drain-source ON resistance: RDS (ON) = 11 mΩ (typ.) • High forward transfer admittance: |Yfs| = 10 S (typ.) • Low leakage current: IDSS = 10 μA (max) (VDS = 30 V) • Enhancement mode: Vth = 1.3 to 2.5 V (VDS = 10 V, ID = 1 mA) Absolute Maximum Ratings (Ta = 25°C) Characteristics Symbol Rating Unit Drain-source voltage VDSS 30 V Drain-gate voltage (RGS = 20 kΩ) VDGR 30 V Gate-source voltage VGSS ±20 V DC (Note 1) ID 11 Pulse (Note 1) IDP 44 PD 1.9 W PD 1.0 W EAS 157 mJ IAR 11 A EAR 0.19 mJ Channel temperature Tch 150 °C Storage temperature range Tstg −55 to 150 °C Drain current Drain power dissipation (t = 10 s) (Note 2a) Drain power dissipation (t = 10 s) (Note 2b) Single pulse avalanche energy (Note 3) Avalanche current Repetitive avalanche energy (Note 2a) (Note 4) A JEDEC ― JEITA ― TOSHIBA 2-6J1B Weight: 0.08 g (typ.) Circuit Configuration 8 7 6 5 1 2 3 4 Note: (Note 1), (Note 2), (Note 3) and (Note 4): See the next page. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). This transistor is an electrostatic-sensitive device. Please handle with caution. 1 2009-09-29 TPC8014 Thermal Characteristics Characteristics Thermal resistance, channel to ambient (t = 10 s) (Note 2a) Thermal resistance, channel to ambient (t = 10 s) (Note 2b) Symbol Max Unit Rth (ch-a) 65.8 °C/W Rth (ch-a) 125 °C/W Marking (Note 5) TPC8014 Part No. (or abbreviation code) Lot No. Note 6 Note 1: Ensure that the channel temperature does not exceed 150°C. Note 2: (a) Device mounted on a glass-epoxy board (a) (b) Device mounted on a glass-epoxy board (b) FR-4 25.4 × 25.4 × 0.8 (unit: mm) FR-4 25.4 × 25.4 × 0.8 (unit: mm) (a) (b) Note 3: VDD = 24 V, Tch = 25°C (initial), L = 1.0 mH, RG = 25 Ω, IAR = 11 A Note 4: Repetitive rating: pulse width limited by max channel temperature Note 5: • on the lower left of the marking indicates Pin 1. ※ Weekly code: (Three digits) Week of manufacture (01 for first week of year, continuing up to 52 or 53) Year of manufacture (The last digit of the calendar year) Note 6: A line under a Lot No. identifies the indication of product Labels. Not underlined: [[Pb]]/INCLUDES > MCV Underlined: [[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]] Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. The RoHS is the Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 2 2009-09-29 TPC8014 Electrical Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Min Typ. Max Unit Gate leakage current IGSS VGS = ±16 V, VDS = 0 V ⎯ ⎯ ±10 μA Drain cut-OFF current IDSS VDS = 30 V, VGS = 0 V ⎯ ⎯ 10 μA V (BR) DSS ID = 10 mA, VGS = 0 V 30 ⎯ ⎯ V (BR) DSX ID = 10 mA, VGS = −20 V 15 ⎯ ⎯ VDS = 10 V, ID = 1 mA 1.3 ⎯ 2.5 VGS = 4.5 V, ID = 5.5 A ⎯ 15 22 VGS = 10 V, ID = 5.5 A ⎯ 11 14 VDS = 10 V, ID = 5.5 A 5 10 ⎯ ⎯ 1860 ⎯ ⎯ 270 ⎯ ⎯ 320 ⎯ ⎯ 9 ⎯ ⎯ 19 ⎯ Drain-source breakdown voltage Gate threshold voltage Vth Drain-source ON resistance RDS (ON) Forward transfer admittance |Yfs| Input capacitance Ciss Reverse transfer capacitance Crss Output capacitance Coss tr VGS Turn-ON time ton Fall time tf Turn-OFF time Total gate charge (gate-source plus gate-drain) toff 0V 4.7 Ω Switching time ID = 5.5 A VOUT 10 V RL = 2.7 Ω Rise time VDS = 10 V, VGS = 0 V, f = 1 MHz VDD ∼ − 15 V < Duty = 1%, tw = 10 μs Qg Gate-source charge 1 Qgs1 Gate-drain (“miller”) charge Qgd VDD ∼ − 24 V, VGS = 10 V, ID = 11 A V V mΩ S pF ns ⎯ 20 ⎯ ⎯ 69 ⎯ ⎯ 39 ⎯ ⎯ 4 ⎯ ⎯ 9 ⎯ nC Source-Drain Ratings and Characteristics (Ta = 25°C) Characteristics Drain reverse current Forward voltage (diode) Pulse (Note 1) Symbol Test Condition Min Typ. Max Unit IDRP ⎯ ⎯ ⎯ 44 A ⎯ ⎯ −1.2 V VDSF IDR = 11 A, VGS = 0 V 3 2009-09-29 TPC8014 ID – VDS ID – VDS 3.3 3.4 3.5 4 6 8 10 16 Drain current ID (A) 10 12 3.2 3.1 3.0 8 2.9 2.8 4 10 3.2 8 6 8 4 Drain current ID (A) 20 3.1 3.3 3.0 3. 6 3.4 2.9 4 2.8 2.7 2 2.7 2.6 VGS = 2.6 V 0 0 1 2 3 Drain-source voltage 4 VGS = 2.5 V 0 0 5 0.2 0.4 Drain-source voltage VDS (V) ID – VGS VDS (V) Drain-source voltage Drain current ID (A) Common source VDS = 10 V Pulse test 100 8 Ta = −55°C 25 4 0.5 1 1.5 2 Gate-source voltage 2.5 3 2.5 Common source Ta = 25°C Pulse test 0.8 0.6 0.4 2.5 5.5 0.2 0 0 4 VGS (V) 4 ID = 11A 8 12 Gate-source voltage |Yfs| – ID 16 20 VGS (V) RDS (ON) – ID 100 100 Common source Ta = 25°C Pulse test −55°C Drain-source ON resistance RDS (ON) (mΩ) (S) Forward transfer admittance ⎪Yfs⎪ 1.0 VDS (V) 1 12 0 0 0.8 VDS – VGS 20 16 0.6 Tc = 100°C 10 25°C 1 30 VGE = 4.5 V 10 VGS = 10 V 3 Common source VDS = 10 V Pulse test 0.1 0.1 1 10 1 1 100 Drain current ID (A) 3 10 30 100 Drain current ID (A) 4 2009-09-29 TPC8014 RDS (ON) – Ta (α) IDR – VDS 25 100 5 (A) 20 15 Drain reverse current IDR VGS = 4.5 V ID = 11, 5.5, 2.5 A 10 10 5 Common source 10 1 3 10 1 Common source Ta = 25°C Pulse test Pulse test 0 −80 −40 0 40 80 120 0.1 0 160 0.4 0.2 Ambient temperature Ta (°C) Capacitance – VDS VDS (V) Vth – Ta Vth (V) Ciss 1000 Gate threshold voltage Coss Crss 100 10 0.1 2.5 2 1.5 1 Common source VDS = 10 V 0.5 ID = 1 mA Pulse test 1 10 Drain-source voltage 0 −80 100 −40 VDS (V) t = 10 s Drain-source voltage (2) 0.8 0.4 50 100 150 30 Common source (2) Device mounted on a glass-epoxy board (b) (Note 2b) 1.2 120 Dynamic input/output characteristics VDS (V) 1.6 80 30 (1) Device mounted on a glass-epoxy board (a) (Note 2a) (1) 40 Ambient temperature Ta (°C) PD – Ta 2 0 Ambient temperature Ta (°C) ID = 11 A 25 Pulse test VDD = 24 V 20 20 VDS 15 15 6 12 12 10 10 6 VDD = 24 V 5 0 0 200 Ta = 25°C 25 5 10 20 30 40 50 VGS (V) (pF) Capacitance C 1.2 3 Common source VGS = 10 V ID = 1 mA Pulse test Drain power dissipation PD (W) 1 0.8 0.6 Drain-source voltage 10000 0 0 VGS = 10 V Gate-source voltage Drain-source ON resistance RDS (ON) (Ω) ID = 11, 5.5, 2.5 A 0 60 Total gate charge Qg (nC) 5 2009-09-29 TPC8014 rth − tw Normalized transient thermal impedance rth (°C/W) 1000 (1) Device mounted on a glass-epoxy board (a) (Note 2a) (2) Device mounted on a glass-epoxy board (b) (Note 2b) (2) t = 10 s 100 (1) 10 1 Single pulse 0.1 0.001 0.01 0.1 1 Pulse width 10 tw 100 1000 (S) Safe operating area 100 1 ms* ID max (pluse) * Drain current ID (A) 10 10 ms* 1 0.1 * Single pulse Ta = 25°C Curves must be derated linearly with increase in temperature. 0.01 0.01 0.1 VDSS max 1 Drain-source voltage 10 100 VDS (V) 6 2009-09-29 TPC8014 RESTRICTIONS ON PRODUCT USE • Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively “Product”) without notice. • This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission. • Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the “TOSHIBA Semiconductor Reliability Handbook” and (b) the instructions for the application that Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR APPLICATIONS. • Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. • Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. • Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. • ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. • Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. • Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 7 2009-09-29