TPCA8A01-H
TOSHIBA Field Effect Transistor with Built-in Schottky Barrier Diode
Silicon N-Channel MOS Type (Ultra-High-Speed U-MOS Ⅲ)
TPCA8A01-H
High Efficiency DC-DC Converter Applications
Notebook PC Applications
Portable Equipment Applications
Built-in schottky barrier diode
0.05 M A
5
5.0±0.2
0.5±0.1 1.27
8
6.0±0.3
•
Unit: mm
0.4±0.1
0.15±0.05
Low forward voltage: VDSF = −0.6 V (max)
Small footprint due to a small and thin package
•
High speed switching
•
Small gate charge: Qsw =11 nC (typ.)
•
Low drain-source ON-resistance: RDS (ON) =4.3 mΩ (typ.)
•
High forward transfer admittance: |Yfs| = 70 S (typ.)
•
Low leakage current: IDSS = 100 μA (max) (VDS = 30 V)
•
Enhancement mode: Vth = 1.1 to 2.3 V (VDS = 10 V, ID = 1 mA)
4
1
0.595
5.0±0.2
0.95±0.05
A
0.166±0.05
0.05 S
S
0.6±0.1
1
4
4.25±0.2
Absolute Maximum Ratings (Ta = 25°C)
8
Characteristic
Symbol
Rating
Unit
Drain-source voltage
VDSS
30
V
Drain-gate voltage (RGS = 20 kΩ)
VDGR
30
V
Gate-source voltage
VGSS
±20
V
(Note 1)
ID
36
Pulsed (Note 1)
IDP
108
PD
45
W
PD
2.8
W
PD
1.6
W
EAS
168
mJ
IAR
36
A
EAR
2.1
mJ
Channel temperature
Tch
150
°C
Storage temperature range
Tstg
−55 to 150
°C
DC
Drain current
Drain power dissipation
(Tc=25℃)
Drain power dissipation
(t = 10 s)
(Note 2a)
Drain power dissipation
(t = 10 s)
(Note 2b)
Single-pulse avalanche energy
(Note 3)
Avalanche current
Repetitive avalanche energy
(Tc=25℃) (Note 4)
A
1.1±0.2
3.5±0.2
•
5 0.8±0.1
1,2,3：SOURCE
5,6,7,8：DRAIN
4：GATE
JEDEC
―
JEITA
―
TOSHIBA
2-5Q1A
Weight: 0.080 g (typ.)
Circuit Configuration
8
7
6
5
1
2
3
4
Note: For Notes 1 to 4, refer to the next page.
Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability
Handbook (“Handling Precautions”/”Derating Concept and Methods”) and individual reliability data (i.e.
reliability test report and estimated failure rate, etc).
This transistor is an electrostatic-sensitive device. Handle with care. Schottky barrier diodes have
large-reverse-current-leakage characteristic compared to other rectifier products. This current leakage combined with
improper operating temperature or voltage may cause thermal runaway. Please take forward and reverse loss into
consideration during design.
1
2010-01-19
TPCA8A01-H
Thermal Characteristics
Characteristic
Thermal resistance, channel to case
(Tc=25℃)
Thermal resistance, channel to ambient
(t = 10 s)
(Note 2a)
Thermal resistance, channel to ambient
(t = 10 s)
(Note 2b)
Symbol
Max
Unit
Rth (ch-c)
2.78
°C/W
Rth (ch-a)
44.6
°C/W
Rth (ch-a)
78.1
°C/W
Marking (Note 5)
TPCA
8A01-H
Type
Lot No.
Note 1: The channel temperature should not exceed 150°C during use
Note 2: (a) Device mounted on a glass-epoxy board (a)
(b) Device mounted on a glass-epoxy board (b)
FR-4
25.4 × 25.4 × 0.8
(Unit: mm)
FR-4
25.4 × 25.4 × 0.8
(Unit: mm)
(a)
(b)
Note 3: VDD = 24 V， Tch = 25°C (initial)， L = 0.1 mH， RG = 25 Ω， IAR = 36 A
Note 4: Repetitive rating: pulse width limited by max. channel temperature
Note 5: * Weekly code: (Three digits)
Week of manufacture
(01 for first week of year, continuing up to 52 or 53)
Year of manufacture
(The last digit of the calendar year)
2
2010-01-19
TPCA8A01-H
Electrical Characteristics (Ta = 25°C)
Characteristic
Symbol
Test Condition
Min
Typ.
Max
Unit
Gate leakage current
IGSS
VGS = ±16 V, VDS = 0 V
⎯
⎯
±10
μA
Drain cut-off current
IDSS
VDS = 30 V, VGS = 0 V
⎯
⎯
100
μA
V (BR) DSS
ID = 10 mA, VGS = 0 V
30
⎯
⎯
V (BR) DSX
ID = 10 mA, VGS = −20 V
15
⎯
⎯
VDS = 10 V, ID = 1 mA
1.1
⎯
2.3
VGS = 4.5 V, ID = 18 A
⎯
6.2
8.5
VGS = 10 V, ID = 18 A
⎯
4.3
5.6
VDS = 10 V, ID = 18 A
35
70
⎯
⎯
1970
⎯
⎯
240
⎯
⎯
950
⎯
⎯
8
⎯
⎯
18
⎯
Drain-source breakdown voltage
Gate threshold voltage
Vth
Drain-source ON-resistance
RDS (ON)
Forward transfer admittance
|Yfs|
Input capacitance
Ciss
Reverse transfer capacitance
Crss
Output capacitance
Coss
tr
VGS
Turn-on time
ton
Fall time
toff
10
⎯
⎯
44
⎯
Total gate charge
(gate-source plus gate-drain)
Qg
VDD ≈ 24 V, VGS = 10 V, ID = 36 A
⎯
35
⎯
VDD ≈ 24 V, VGS = 5 V, ID = 36 A
⎯
19
⎯
Gate-source charge 1
Qgs1
⎯
6
⎯
Gate-drain (“Miller”) charge
Qgd
⎯
8.8
⎯
Gate switch charge
QSW
⎯
11
⎯
VDD ≈ 15 V
Duty ≤ 1%, tw = 10 μs
VDD ≈ 24 V, VGS = 10 V, ID = 36 A
V
mΩ
S
pF
ns
⎯
tf
Turn-off time
0V
4.7 Ω
Switching time
ID = 18A
VOUT
10 V
RL = 0.83Ω
Rise time
VDS = 10 V, VGS = 0 V, f = 1 MHz
V
nC
Source-Drain Ratings and Characteristics (Ta = 25°C)
Characteristic
Peak forward
current
Forward voltage (diode)
Pulse
(Note 1)
Symbol
Test Condition
Min
Typ.
Max
Unit
IDRP
⎯
⎯
⎯
108
A
IDR = 1.0 A, VGS = 0 V
⎯
− 0.45
− 0.6
IDR = 36 A, VGS = 0 V
⎯
⎯
− 1.2
VDSF
3
V
2010-01-19
TPCA8A01-H
ID – VDS
50
5
3.6
6
3.4
4
ID
3.2
20
Drain current
30
3
10
2.8
4
Common source
3.6 Ta = 25°C
Pulse test
3.8
5
80
4.5
10
8
10
4.5
6
(A)
(A)
ID
Drain current
3.8
8
40
ID – VDS
100
Common source
Ta = 25°C
Pulse test
3.4
60
3.2
40
3
2.8
20
VGS = 2.6 V
0
VGS = 2.6 V
0
0.2
0.4
0.6
Drain-source voltage
0.8
VDS
0
1
0
(V)
1
2
(V)
Common source
Ta = 25°C
Pulse test
0.32
VDS
(A)
60
Drain-source voltage
ID
Drain current
5
(V)
VDS – VGS
40
25
100
20
Ta = −55°C
0
0
1
2
3
4
Gate-source voltage
5
VGS
0.24
ID = 36 A
0.16
18
0.08
9
0
6
0
(V)
2
4
⎪Yfs⎪ − ID
Drain-source ON-resistance
RDS (ON) (mΩ)
(S)
100
100
Ta = −55°C
25
1
Common source
VDS = 10 V
Pulse test
0.1
0.1
1
Drain current
10
ID
8
VGS
10
(V)
RDS (ON) − ID
100
10
6
Gate-source voltage
1000
|Yfs|
VDS
0.4
Common source
VDS = 10 V
Pulse test
80
Forward transfer admittance
4
Drain-source voltage
ID – VGS
100
3
10
4.5 V
VGS = 10 V
1
0.1
100
(A)
Common source
Ta = 25°C
Pulse test
1
Drain current
4
10
ID
100
(A)
2010-01-19
TPCA8A01-H
RDS (ON) − Ta
IDR − VDS
1000
(A)
Common source
Pulse test
IDR
ID = 9A18A,36A
8
Drain reverse current
Drain-source ON-resistance
RDS (ON) (mΩ)
12
VGS = 4.5 V
ID = 9A18A,36A
4
VGS = 10 V
0
−80
−40
0
40
80
Ambient temperature
120
Ta
100
4.5
10
VGS = 0 V
1
Common source
Ta = 25°C
Pulse test
0.1
160
5
10
0
(°C)
−0.2
−0.4
Drain-source voltage
Capacitance − VDS
(V)
Vth (V)
1000
Gate threshold voltage
Coss
C
(pF)
VDS
−1.0
3
Ciss
Capacitance
−0.8
Vth − Ta
10000
Crss
100
10
−0.6
Common source
VGS = 0 V
f = 1 MHz
Ta = 25°C
1
0.1
10
1
Drain-source voltage
1
0
−80
100
VDS
2
Common source
VDS = 10 V
ID = 1 mA
Pulse test
−40
0
40
Ambient temperature
(V)
80
Ta
120
160
(°C)
Dynamic input/output
characteristics
16
VGS
40
20
30
12
VDS = 24V
VDD = 12 V
6
20
24
8
12
10
4
6
0
0
VGS
8
16
Total gate charge
24
Qg
32
Gate-source voltage
Drain-source voltage
VDS
(V)
Common source
ID = 36 A
Ta = 25°C
Pulse test
(V)
50
0
40
(nC)
5
2010-01-19
TPCA8A01-H
rth – tw
1000
(1) Device mounted on a glass-epoxy board (a) (Note 2a)
Transient thermal impedance
rth (℃/W)
(2) Device mounted on a glass-epoxy board (b) (Note 2b)
(2)
(3) Tc = 25℃
100
(1)
10
(3)
1
Single - pulse
0.1
0.001
0.01
0.1
1
Pulse width
10
tw
100
(s)
PD – Ta
(W)
(1)
PD
2.5
PD – Tc
50
(1) Device mounted on a glass-epoxy
board (a) (Note 2a)
(2) Device mounted on a glass-epoxy
board (b) (Note 2b)
t = 10s
2
1.5
Drain power dissipation
Drain power dissipation
PD
(W)
3
(2)
1
0.5
0
0
40
1000
120
80
Ambient temperature
Ta
40
30
20
10
0
0
160
(°C)
40
80
Case temperature
120
Tc
160
(°C)
Safe operating area
100
ID max (Pulse) *
t =1 ms *
ID max (Continuous)
t =10 ms *
Drain current
ID
(A)
1000
DC Operation
Tc = 25°C
10
1
*
Single - pulse
Ta = 25°C
Curves must be derated
linearly with increase in
0.1
0.1
temperature.
VDSS max
1
Drain-source voltage
10
VDS
100
(V)
6
2010-01-19
TPCA8A01-H
IDSS – Tch
IDR – VDSF
100
Pulse test
IDSS
10
125
Drain cutoff current
75
Ta = 25°C
1
0.1
0
−0.2
−0.4
−0.6
Drain-source voltage
−0.8
VDSF
(V)
Pulse test
VDS = 10 V
VDS = 20 V
10000
VDS = 30 V
VDS = 5 V
1000
100
10
0
−1
(typ.)
VGS = 0 V
(μA)
VGS = 0 V
(A)
IDR
Drain reverse current
100000
40
80
Channel temperature
120
Tch
160
(°C)
Tch – VDS
160
Channel temperature
Tch
(°C)
Pulse test
VGS = 0 V
120
80
40
0
0
10
20
Drain-source voltage
30
VDS
40
(V)
7
2010-01-19
TPCA8A01-H
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively “Product”) without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the
Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of
all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes
for Product and the precautions and conditions set forth in the “TOSHIBA Semiconductor Reliability Handbook” and (b) the
instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their
own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such
design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,
diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating
parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR
APPLICATIONS.
• Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring
equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document.
Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or
reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious
public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used
in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling
equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric
power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this
document.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product
or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of
noncompliance with applicable laws and regulations.
8
2010-01-19
