TEN 5-2411

DC/DC Converters TEN 5 Series, 6 Watt Features ◆ Wide 2:1 input range ◆ Full SMD-design ◆ High efficiency up to 86% ◆ Extended operating temperature UL 60950-1 range –40°C to 85°C ◆ I/O isolation 1’500 VDC ◆ Indefinite short circuit protection ◆ Input filter to meet EN 55022, class A and FCC, level A without external components ◆ Shielded metal case with insulated baseplate ◆ 24-pin DIP with industry standard pinout ◆ High reliability, MTBF >1 Mio. h ◆ 3-year product warranty The TEN 5 Series is a range of DC/DC-converter modules with wide input range of 2:1. State of the art SMD-technology guarantees a product with very high reliability and good cost /performance ratio. I/O-isolation of 1’500 VDC together with conducted noise compliance to EN 55022-A and FCC level A makes these converters ideal for a wide range of applications in communications, mobile battery powered equipments and industrial systems. Models Ordercode TEN 5-0510 TEN 5-0511 TEN 5-0512 TEN 5-0513 TEN 5-0521 TEN 5-0522 TEN 5-0523 TEN 5-1210 TEN 5-1211 TEN 5-1212 TEN 5-1213 TEN 5-1221 TEN 5-1222 TEN 5-1223 TEN 5-2410 TEN 5-2411 TEN 5-2412 TEN 5-2413 TEN 5-2421 TEN 5-2422 TEN 5-2423 TEN 5-4810 TEN 5-4811 TEN 5-4812 TEN 5-4813 TEN 5-4821 TEN 5-4822 TEN 5-4823 http://www.tracopower.com Input voltage range 4.5 – 7 VDC (5 VDC nominal) 9 – 18 VDC (12 VDC nominal) 18 – 36 VDC (24 VDC nominal) 36 – 75 VDC (48 VDC nominal) Output voltage 3.3 VDC 5 VDC 12 VDC 15 VDC ±5 VDC ±12 VDC ±15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ±5 VDC ±12 VDC ±15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ±5 VDC ±12 VDC ±15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ±5 VDC ±12 VDC ±15 VDC Output current max. 1200 mA 1000 mA 500 mA 400 mA ±500 mA ±250 mA ±200 mA 1200 mA 1000 mA 500 mA 400 mA ±500 mA ±250 mA ±200 mA 1200 mA 1000 mA 500 mA 400 mA ±500 mA ±250 mA ±200 mA 1200 mA 1000 mA 500 mA 400 mA ±500 mA ±250 mA ±200 mA Efficiency typ. 75 % 79 % 82 % 82 % 79 % 82 % 82 % 77 % 81 % 84 % 84 % 81 % 84 % 84 % 79 % 83 % 86 % 86 % 83 % 86 % 86 % 79 % 83 % 86 % 86 % 83 % 86 % 86 % Page 1 of 3 DC/DC Converters TEN 5 Series 6 Watt Input Specifications Input current no load 5 12 24 48 Vin Vin Vin Vin models: models: models: models: 80 mA typ. 30 mA typ. 15 mA typ. 8 mA typ. Start-up voltage / 5 Vin models: 4.4 VDC / 4.0 VDC (or lower) under voltage shut down 12 Vin models: 8.0 VDC / 8.0 VDC (or lower) 24 Vin models: 16.0 VDC / 16.0 VDC (or lower) 48 Vin models: 32.0 VDC / 32.0 VDC (or lower) long term operation at undervoltage will demage the converter! Surge voltage (1 sec. max.) 5 12 24 48 Vin Vin Vin Vin models: models: models: models: 10 V max. 25 V max. 50 V max. 100 V max. Conducted noise (input) EN 55022 class A, FCC part 15, level A Output Specifications Voltage set accuracy 1.0 % Regulation – Input variation Vin min. to Vin max. – Load variation 20 – 100 % single output models: dual output models balanced load: dual output models unbalanced load: 0.3 % max. 1.0 % max. 2.0 % max. 5.0 % max. (25 % / 100 %) Minimum load 5 % of rated max current (operation at lower load condition is safe but a higher output ripple will be experienced) Ripple and noise (20 MHz Bandwidth) 50 mVpk-pk typ., 75 mVpk-pk max. Temperature coefficient ±0.02 %/K Output current limitation >120 % of Iout max., foldback Short-circuit protection indefinite (automatic recovery) Start up time (nominal Vin and constant resistive load) 10 ms typ. (for power on and remote on) Capacitive load single output models: 6800 µF max. dual output models: 1000 µF max. (each output) General Specifications Temperature ranges – Operating –40°C to +85°C – Case temperature +90°C max. – Storage –50°C to +125°C Derating 3.3 %/K above 70°C Humidity (non condensing) 95 % rel H max. Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >1 Mio. h Isolation voltage (60 sec.) – Input/Output 1’500 VDC Isolation capacitance – Input/Output 380 pF typ. Isolation resistance – Input/Output >1‘000 M Ohm (500 VDC) Switching frequency 300 kHz typ. (Pulse frequency modulation PFM) Safety standards UL 60950-1, IEC/EN 60950-1 Environmental compliance – Reach www.tracopower.com/info/reach-declaration.pdf – RoHS directive 2011/65/EU All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TEN 5 Series 6 Watt Physical Specifications Casing material steel, metal Baseplate material non conductive FR4 Potting material Silicone (UL 94 V-0 rated) Weight 16.9 g (0.59 oz) Soldering temperature max. 260°C / 10 sec. Supporting documents: www.tracopower.com/overview/ten5 4.5 15.24 (0.6) 16 (0.2) 5.08 31.8 (1.25) 23 22 Bottom view (0.1) 2.54 (0.18) Outline Dimensions 14 Insulated Baseplate 2.54 15.22 (0.1) (0.6) 4.1 10.2 20.3 (0.16) (0.4) (0.8) 2 3 Pin-Out Pin Single Dual 2 –Vin (GND) –Vin (GND) 3 –Vin (GND) –Vin (GND) 9 No pin Common 11 No con. –Vout 9 14 +Vout +Vout 11 16 –Vout Common 22 +Vin (Vcc) +Vin (Vcc) 23 +Vin (Vcc) +Vin (Vcc) Dimensions in [mm], () = Inch Pin diameter ø 0.5 ±0.05 (0.02 ±0.002) Tolerances ±0.25 (±0.01) Pin pitch tolerances ±0.13 (±0.005) Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com Rev. December 15, 2021 www.tracopower.com Page 3 of 3