TME1509S

DC/DC Converter TME Series Features Single-in-Line Package (SIP) I/O-Isolation 1‘000 VDC High Efficiency up to 80% Operating Temperature – 40°C to +85°C Pin-compatible with other Manufacturers 100% Burn-in (8 h) 2 Year Product Warranty 1 Watt The TME series is a range of sub-miniature , isolated DC/DC-converters in a SIP-package, which requires only 0.7 cm2 of board space. They provide a cost effective solution to generate supplementary, isolated voltages. Full SMD-design and a 100 % production test of parameters ensure a high reliability of this product. Models Ordercode TME 0505S TME 0509S TME 0512S TME 0515S TME 1205S TME 1509S TME 1212S TME 1215S TME 2405S TME 2409S TME 2412S TME 2415S Input voltage Output voltage 5 VDC 9 VDC 12 VDC 15 VDC 5 VDC 9 VDC 12 VDC 15 VDC 5 VDC 9 VDC 12 VDC 15 VDC Output current max. 200 mA 110 mA 80 mA 65 mA 200 mA 110 mA 80 mA 65 mA 200 mA 110 mA 80 mA 65 mA Efficiency typ. 70 76 77 78 71 77 79 80 70 76 79 79 % % % % % % % % % % % % 5 VDC ±10% 12 VDC ±10% 24 VDC ±10% www.tracopower.com Page 1 DC/DC Converter TME Series 1 Watt Input Specifications Input current no load /full load 5 Vin models 12 Vin models 24 Vin models 5 Vin models 12 Vin models 24 Vin models 30 mA / 290 mA typ. 15 mA / 120 mA typ. 10 mA / 60 mA typ. 9 V max. 18 V max. 30 V max. 0.3 A max. can be reduced by ext. 1–3.3 µF polyester film capacitor Internal capacitors Surge voltage (1 sec. max.) Reverse voltage protection Reflected input ripple current Input filter Output Specifications Voltage set accuracy Regulation – Input variation – Load variation 20 – 100 % ±3% ± 1.2 % / 1 % change Vin ± 10 % max. 150 mV pk-pk max. ± 0.02 % / °C limited 1 sec. max. 33 µF max. Ripple and noise (20 MHz Bandwidth) Temperature coefficient Short circuit protection Capacitive load General Specifications Temperature ranges – Operating – Case temperature – Storage – 40 °C ... +85 °C + 95 °C max. – 40 °C ... +105 °C 95 % rel H max. >2’000’000 h @ 25 °C 1‘000 VDC 60 pF typ. >1‘000 Mohm 90 kHz typ. (Frequency modulation) ± 30 % max. Humidity (non condensing) Reliability, calculated MTBF (MIL-HDBK-217 E) Isolation voltage Isolation capacity Isolation resistance Switching frequency Frequency change over line and load Input/Output Input/Output Input/Output All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. www.tracopower.com Page 2 DC/DC Converter TME Series 1 Watt Physical Specifications Case material Package weight Soldering temperature 5 Vin & 12 Vin models 24 Vin models non conductive black plastic (flammability to UL 94-V0) 1.3 g (0.05 oz) 1.7 g (0.06 oz) max. 260°C / 10 sec Outline Dimensions mm (inches) Pin-Out 10.2 (0.4) Pin 1 2 3 4 Single –Vin (GND) +Vin (Vcc) –Vout +Vout 0.5 (0.02) 1.9 ±0.5 (0.08 ±0.02) 2.54 2.54 2.54 (0.1) (0.1) (0.1) 11.5 (0.45) 3.2(0.13) 0.5 (0.02) 0.5 (0.02) 4.2 (0.17) 1.8 (0.07) Bottom view 0.5 (0.02) Tolerances ±0.25 (0.01) pins ±0.05 (0.002) Specifications can be changed without notice Rev. 05/00 Jenatschstrasse 1 • CH-8002 Zurich • Switzerland Tel. +41-1284 2911 • Fax +41-1201 1168 • e-mail: sales@traco.ch • internet: http://www.tracopower.com 5.2 (0.2) 1 2 3 4 7.0 (0.28) 24 V Models 0.25 (0.01) 6.0 (0.24) Page 3