TMR2-0511E

DC/DC Converters TMR 2E Series, 2 Watt Features ◆ Wide 2:1 input voltage range ◆ Compact SIP-8 package ◆ Cost optimized design ◆ Temperature range –40° to +85°C ◆ I/O isolation 1000VDC ◆ Remote On/Off control ◆ Fully RoHS compliant ◆ 3-year product warranty The TMR-2E series is a family of isolated 2W dc-dc converter modules with regulated output, featuring wide 2:1 input voltage ranges. The product comes in a compact SIP-8 plastic package with small footprint occupying only 2.0 cm2 (0.3 square in.) of board space. An excellent efficiency allows –40° to +85°C operation temperature. Further features include remote On/Off control and continuous short circuit protection. The compact dimensions and cost optimise design make this converters an ideal solution for applications in communication equipment, instrumentation and industrial electronics. Models Order code TMR 2-0510E TMR 2-0511E TMR 2-0512E TMR 2-1210E TMR 2-1211E TMR 2-1212E TMR 2-2410E TMR 2-2411E TMR 2-2412E TMR 2-4810E TMR 2-4811E TMR 2-4812E Input voltage range 4.5 – 9.0 VDC (5 VDC nominal) 9 – 18 VDC (12 VDC nominal) 18 – 36 VDC (24 VDC nominal) 36 – 75 VDC (48 VDC nominal) Output voltage 3.3 VDC 5 VDC 12 VDC 3.3 VDC 5 VDC 12 VDC 3.3 VDC 5 VDC 12 VDC 3.3 VDC 5 VDC 12 VDC Output current max. 500 mA 400 mA 167 mA 500 mA 400 mA 167 mA 500 mA 400 mA 167 mA 500 mA 400 mA 167 mA Efficiency typ. 70 % 73 % 75 % 73 % 77 % 80 % 72 % 77 % 81 % 71 % 73 % 79 % http://www.tracopower.com Page 1 of 3 DC/DC Converters TMR 2E Series Input Specifications Input current at no load (nominal input voltage) 4.5–9 9-–18 18–36 36–75 4.5–9 9-–18 18–36 36–75 4.5–9 9-–18 18–36 36–75 Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin models: models: models: models: models: models: models: models: models: models: models: models: 40 mA typ. 20 mA typ. 10 mA typ. 8 mA typ. 520 mA typ. 200 mA typ. 100 mA typ. 50 mA typ. 15 V max. 25 V max. 50 V max. 100 V max. 1.0 A max. 5 V/ms, max. (complies with ETS300 132 part 4.4) 4.5–9 9-–18 18–36 36–75 Vin Vin Vin Vin models: models: models: models: 400 mA typ. 300 V mA typ. 200 V mA typ. 500 V mA typ. EN 55022 level A, FCC part 15, level A with external capacitor (tba) ±2 % max – Input variation Vin min. to Vin max. – Load variation 25 – 100% 0.5 % max. 0.75 % max. 25 % of rated max. load (operation at lower load condition is safe but a higher output ripple will be experienced) 0.1 %/°C 50 mVpk-pk max. 100 µs typ. >120 % of Iout max. continuous, automatic recovery 3.3 VDC models: 2‘200 µF max. 5 VDC models: 1‘000 µF max. 12 VDC models: 170 µF max. – Operating – Case temperature – Storage –40°C to +85°C +90°C max. –55°C to +105°C 3.0 %/K above 65°C 95 % rel. H max. >1 Mio h 1’000 VDC 120 pF max. >1 GOhm 100 – 650 kHz (FM) – On: – Off: – Off stand by input current open or short circuit 2.7 to 15 VDC ref. to –Vin 1 mA max. – Input/Output – Input/Output – Input/Output (500 VDC) 2 Watt Input current at full load (nominal input voltage) Surge voltage (1000 msec. max.) Reverse voltage protection Input voltage variation (dv/dt) Reflected input ripple current Conducted noise (input) Output Specifications Voltage set accuracy Regulation Minimum load Temperature coefficient Ripple and noise (20 MHz bandwidth) Transient response setting time (25% load step change) Current limitation Short circuit protection Capacitive load General Specifications Temperature ranges Load derating Humidity (non condensing) Reliability, calculated MTBF ( MIL-HDBK-217F @ 25°C, ground benign) Isolation voltage (60 sec) Isolation capacity Isolation resistance Switching frequency Remote On/Off All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TMR 2E Series Physical Specifications Casing material Potting material Weight Soldering temperature non-conductive plastic silicon, UL 94V-0 rated 4.8g (0.17oz) max. 260°C / 10 sec. 2 Watt Outline Dimensions Pin-Out Pin (0.37) Bottom view 1 2 3 5 6 7 8 0.25 (0.01) 1 2 3 5 6 7 8 –Vin (GND) +Vin (Vcc) Remote On/Off No con. +Vout –Vout No con. 0.5 (0.02) (0.11) 2.7 9.3 No con. = Pin to be isolated from circuitry 0.5 (0.02) 11.2 (0.44) 2.0 2.54 2.54 (0.08) (0.1) (0.1) 5.08 (0.2) 2.54 2.54 2.54 (0.1) (0.86) (0.1) (0.1) Dimensions in [mm], () = Inch Tolerances: ±0.5 (±0.02) Pin pich tolerances: ±0.25 (±0.005) 21.8 Specifications can be changed any time without notice. Rev. 09/09 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · info@traco.ch · www.tracopower.com (0.13) 3.2 Page 3 of 3