TMR2423

DC/DC Converters TMR 2 Series, 2 Watt Features ◆ Wide 2: Input Voltage Range ◆ Compact SIP-8 Package ◆ Small Footprint ◆ Full SMD Design ◆ Temperature Range –40° to +75°C ◆ High Efficiency ◆ Excellent Load and Line Regulation ◆ Indefinite Short-circuit Protection ◆ I/O-Isolation 000VDC ◆ Remote On/Off Control ◆ Fully RoHS compliant ◆ 3 Year Product Warranty compliant RoHS The TMR-2 series is a family of isolated 2W dc-dc converter modules with regulated output, featuring wide 2:1 input voltage ranges. The product comes in a compact SIP-8 plastic package with small footprint occupying only 2.0 cm2 (0.3 square in.) of board space. An excellent efficiency allows –40° to +75°C operation temperatures at full load. Further features include remote On/Off control and continuous short circuit protection. The ultra-compact dimensions of these converters make them an ideal solution for many space critical applications in communication equipment, instrumentation and industrial electronics. Models Ordercode TMR 050 TMR 05 TMR 052 TMR 052 TMR 0522 TMR 0523 TMR 20 TMR 2 TMR 22 TMR 22 TMR 222 TMR 223 TMR 240 TMR 24 TMR 242 TMR 242 TMR 2422 TMR 2423 TMR 480 TMR 48 TMR 482 TMR 482 TMR 4822 TMR 4823 http://www.tracopower.com Input voltage range Output voltage 3.3 VDC 5 VDC 12 VDC ±5 VDC ±12 VDC ±15 VDC 3.3 VDC 5 VDC 12 VDC ±5 VDC ±12 VDC ±15 VDC 3.3 VDC 5 VDC 12 VDC ±5 VDC ±12 VDC ±15 VDC 3.3 VDC 5 VDC 12 VDC ±5 VDC ±12 VDC ±15 VDC Output current max. 500 mA 400 mA 165 mA ±200 mA ±85 mA ±65 mA 500 mA 400 mA 165 mA ±200 mA ±85 mA ±65 mA 500 mA 400 mA 165 mA ±200 mA ±85 mA ±65 mA 500 mA 400 mA 165 mA ±200 mA ±85 mA ±65 mA Efficiency typ. 64 % 66 % 71 % 64 % 69 % 71 % 70 % 73 % 80 % 73 % 78 % 78 % 71 % 74 % 81 % 74 % 78 % 80 % 70 % 73 % 79 % 71 % 77 % 77 % Page  of 3 4.5 – 9.0 VDC 9 – 8 VDC 8 – 36 VDC 36 – 75 VDC DC/DC Converters TMR 2 Series Input Specifications Input current at full load (nominal input) Surge voltage (100 msec. max.) Input voltage variation (dv/dt) Input Filter Start up time 5 12 24 48 5 12 24 48 Vin Vin Vin Vin Vin Vin Vin Vin models: models: models: models: models: models: models: models: 645 mA max. 242 mA max. 117 mA max. 62 mA max. 15 V max. 25 V max. 50 V max. 100 V max. 2 Watt 5 V/ms, max. (complies to ETS 300 132 part. 4.4) capacitor type 1 ms typ. (at nominal input and resistive load) ±1 % Output Specifications Voltage set accuracy Regulation Temperature coefficient Short circuit protection Minimum load – Input variation Vin min. to Vin max. 0.5 % max. – Load variation 10–100 % 3.3 VDC models: 0.85 % max. single output models: .75 % max. 0 dual output models balanced load: 1.0 % max. dual output models asymetric load: 5.0 % max. (25% /100%) 50 mVpk-pk max. ± 0.1 %/°C continuous, automatic recovery 10% of rated max current (operation at lower load condition is safe but a higher output ripple will be experianced) 3.3 VDC / 5 VDC output models: 2’200 µF max. / 1’000 µF max. 12 VDC / ±5 VDC output models: 170 µF max. / ±470 µF max. ±12 VDC / ±15 VDC output models: 100 µF max. / ± 47 µF max. – 40 °C ... + 75 °C (no derating) – 55 °C ... + 105 °C 95 % rel. H max. > 2.3 Mio h @ 25°C 1’000 VDC 300 pF max. > 1‘000 MOhm 100 to 650 kHz (PFM) open or high impedance 4...8 mA input current applied via 1KW resistor max. 1mA non-conductive plastic epoxy, UL 94V-0 - rated 4.8g (0.17oz) Ripple and noise (20 MHz Bandwidth) Capacitive load Temperature ranges – Operating – Storage General Specifications Humidity (non condensing) Reliability, calculated MTBF (MIL-HDBK-217 F) Isolation voltage (60 sec) Isolation capacity Isolation resistance Switching frequency Remote On/Off Case material Potting material Weight – Input/Output – Input/Output – Input/Output (500 VDC) – On: – Off: – Off stand by input current Physical Specifications Application notes can be downloaded under: www.tracopower.com/products/tmr2_application.pdf All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TMR 2 Series EMC Characteristics - Use an electrolytic low ESR capacitor at input side to reduce reflected ripple current. - In order to meet EN55022 class B additionally use a choke to build an L/C filter as follows: Recommended values for filter: Input 5VDC 12VDC 24VDC 48VDC C 100µF 100µF 10µF 10µF L 10µH 10µH 120µH 120µH 2 Watt + Input + –C L + TMR Output – – Outline Dimensions mm (inches) Pin-Out (0.36) Bottom view 1 2 3 5 6 7 8 0.25 (0.01) Pin  2 3 5 6 7 8 Single –Vin (GND) +Vin (Vcc) Remote On/Off No function +Vout –Vout No function Dual –Vin (GND) +Vin (Vcc) Remote On/Off No function +Vout Common –Vout 0.5 (0.02) 0.5 (0.02) 11.1 (0.44) (0.16) ±0.5 2.0 2.54 2.54 (0.1) (0.1) 5.08 (0.2) 2.54 2.54 2.54 (0.1) (0.1) (0.1) (0.08 ±0.025 ) 21.8 (0.86) Specifications can be changed any time without notice Rev. 10/07 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · info@traco.ch · www.tracopower.com 4.0 (0.13) 3.2 9.2 Page 3 of 3