TMR3-1213WI

DC/DC Converters TMR 3WI Series, 3 Watt Features ◆ Highest power density in SIP package ◆ Ultra wide 4:1 input range ◆ Small footprint: 21.8 x 9.2 mm ◆ Temperature range –40° to +85°C ◆ High efficiency up to 81% ◆ Excellent load and line regulation ◆ Short-circuit protection ◆ I/O isolation 1500 VDC ◆ Remote On/Off control ◆ 3-year product warranty pending The TMR-3WI series is a new family of isolated 3W DC/DC converters with regulated output, featuring ultra-wide 4:1 input voltage range. The product comes in a ultra-compact SIP plastic package with a small footprint occupying only 2.0 cm2 (0.3 square in.) of board space. An excellent efficiency allows –40° to +85°C operation temperatures. Further features include remote On/Off control and continuous short circuit protection. The very compact dimensions of these converters make them an ideal solution for many space critical applications in battery-powered equipment and instrumentation. Models Order code TMR 3-1210WI TMR 3-1211WI TMR 3-1212WI TMR 3-1213WI TMR 3-1221WI TMR 3-1222WI TMR 3-1223WI TMR 3-2410WI TMR 3-2411WI TMR 3-2412WI TMR 3-2413WI TMR 3-2421WI TMR 3-2422WI TMR 3-2423WI TMR 3-4810WI TMR 3-4811WI TMR 3-4812WI TMR 3-4813WI TMR 3-4821WI TMR 3-4822WI TMR 3-4823WI Input voltage Output voltage 3.3 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC Output current max. 700 mA 600 mA 250 mA 200 mA ± 300 mA ± 125 mA ± 100 mA 700 mA 600 mA 250 mA 200 mA ± 300 mA ± 125 mA ± 100 mA 700 mA 600 mA 250 mA 200 mA ± 300 mA ± 125 mA ± 100 mA Efficiency typ. 74 % 78 % 80 % 80 % 80 % 80 % 80 % 75 % 80 % 81 % 81 % 79 % 80 % 81 % 74 % 79 % 79 % 79 % 79 % 79 % 80 % 4.5 – 18 VDC (12 VDC nominal) 9 – 36 VDC (24 VDC nominal) 18 – 75 VDC (48 VDC nominal) http://www.tracopower.com Page 1 of 3 DC/DC Converters TMR 3WI Series Input Specifications Input current at full load 12 Vin models: 340 mA max. 24 Vin models: 170 mA max. 48 Vin models: 85 mA max. 12 Vin models: 40 mA max. 24 Vin models: 25 mA typ. 48 Vin models: 15 mA typ. 12 Vin models: 25 V max. 24 Vin models: 50 V max. 48 Vin models: 100 V max. inernal capacitor EN 61000-4-2, air ±8 kV, contact ±6 kV, perf. criteria A EN 61000-4-3, 10 V/m, perf. criteria A EN 61000-4-4, ± 2 kV, perf. criteria A EN 61000-4-5, ± 1 kV perf. criteria A With external input capacitor e.g. Nippon chemi-con KY 100 µF, 100 V, ESR 110 mOhm EN 61000-4-6, 10 Vrms, perf. criteria A ±1 % max – Input variation Vin min. to Vin max. 0.2 % max. – Load variation 0 – 100% single output models: 1.0 % max. dual output models: 1.0 % max. balanced load – Load cross regulation 25/100% 5.0 % max. (dual output models) not required 0.02 %/K 30 mVpk-pk max. 30 ms typ. 30 ms typ. 250 µs typ. continuous, automatic recovery 3.3 5 12 15 ±5 ±12 ±15 – Operating – Case temperature – Storage VDC VDC VDC VDC VDC VDC VDC models: models: models: models: models: models: models: 1‘760 µF max. 1’000 µF max. 170 µF max. 110 µF max. ±470 µF max. ±100 µF max. ±47 µF max. –40°C to +85°C +100°C max. –55°C to +125°C 3.3 %/K above 70°C 95 % rel. H max. >1.7 Mio h – Power On – Remote On 3 Watt Input current at no load Surge voltage (100 msec. max.) Input filter ESD (electrostatic discharge) Radiated immunity Fast transient / Surge Conducted immunity Output Specifications Voltage set accuracy Regulation Minimum load Temperature coefficient Ripple and noise (20 MHz Bandwidth) Start up time (constant resistive load) Short circuit protection Capacitive load Transient response setting time (25% load step change) General Specifications Temperature ranges Load derating Humidity (non condensing) Reliability, calculated MTBF ( MIL-HDBK-217F @ 25°C, ground benign) All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TMR 3WI Series General Specifications Isolation voltage (60 sec) Isolation capacity Isolation resistance Switching frequency Remote On/Off – On: – Off: – Off stand by input current – Input/Output – Input/Output – Input/Output (500 VDC) 1’500 VDC 200 pF max. >1 GOhm 100 kHz (PWM) open or high impedance 2...4 mA to applied via 1 kOhm resistor 2.5 mA max. MIL-STD-810E UL /cUL 60950-1, EN 60950-1, IEC 60950-1 – UL/cUL – Reach – RoHS pending w ww.tracopower.com/products/tmr3wi-reach.pdf 3 Watt Vibration and thermal shock Safety standards Safety approvals Environmental compliance Application notes RoHS Directive 2002/95/EC www.tracopower.com/products/tmr3wi-application.pdf Physical Specifications Casing material Potting material Weight non-conductive plastic silicon, UL 94V-0 rated 4.8g (0.17oz) Outline Dimensions Pin-Out (0.36) Bottom view 1 2 3 5 6 7 8 0.25 (0.01) Pin 1 2 3 5 6 7 8 Single –Vin (GND) +Vin (Vcc) Remote On/Off No con. +Vout –Vout No con. Dual –Vin (GND) +Vin (Vcc) Remote On/Off No con. +Vout Common –Vout 0.5 (0.02) 0.5 (0.02) 11.1 (0.44) (0.16) 4.0 (0.13) 3.2 9.2 2.0 2.54 2.54 (0.08 5.08 (0.2) 2.54 2.54 2.54 (0.1) (0.1) (0.1) (0.86) (0.1) (0.1) 21.8 Dimensions in [mm], () = Inch Pin dimension tolerances 0.1 (0.004) Pin pitch tolerances: ±0.25 (±0.01) Tolerances: ±0.5 (±0.02) Specifications can be changed any time without notice. Rev. 09/09 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · info@traco.ch · www.tracopower.com Page 3 of 3