TMV0505EN

DC/DC Converters TMV-EN Series, 1 Watt compliant RoHS Features ◆ Isolation Test Voltage 6’000 Vpk ◆ With supplementary Insulation, rated for 250 Vrms working Voltage ◆ Physical Clearance of Isolation Barrier 2.5 mm min. ◆ Certified to IEC/EN 60950 Safety Standards Safety Barrier 100% Production Test ◆ ◆ ◆ ◆ Low Coupling Capacity Single-in-Line Package (SIP) Lead free Design, RoHS compliant 3 Year Product Warranty The TMV-EN series are dc/dc converters with supplementary high I/O-isolation, to comply with safety standard IEC/EN 60950. They are designed for applications where approved isolation is required, i.e. information technology equipment or medical equipment. SMT-design and a special transformer technology made it possible to build these converters in a very small SIP-package, requiring a minimum space on the PCB. Models Ordercode TMV 0505 EN TMV 0512 EN TMV 0515 EN TMV 0505DEN TMV 0512DEN TMV 0515DEN TMV 1205 EN TMV 1212 EN TMV 1215 EN TMV 1205DEN TMV 1212DEN TMV 1215DEN 12 VDC ±10% 5 VDC ±10% Input voltage Output voltage 5 VDC 12 VDC 15 VDC ± 5 VDC ±12 VDC ±15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ±12 VDC ±15 VDC Output current max. 200 mA 80 mA 65 mA ±100 mA ± 40 mA ± 30 mA 200 mA 80 mA 65 mA ±100 mA ± 40 mA ± 30 mA Efficiency typ. 65 % 65 % 65 % 65 % 71 % 72 % 65 % 65 % 65 % 65 % 73 % 74 % http://www.tracopower.com Page 1 of 3 DC/DC Converters TMV-EN Series Input Specifications Input current no load /full load Surge voltage (1 sec. max.) Reverse voltage protection Reflected input ripple current Input filter 5 Vin models 55 mA / 300 mA typ. 12 Vin models 30 mA / 125 mA typ. 5 Vin models 9 V max. 12 Vin models 18 V max. 0.3 A max. can be reduced by ext. 1–3.3 µF polyester film capacitor internal capacitor ±3% ± 1 % max. ± 1.2 % / 1 % change Vin < 10 % 120 mV pk-pk typ. ± 0.02 % / K limited 1 sec. max. – Single output models – Dual output models – Isolation test voltage (tested for 1 sec.) – I/O isolation voltage Input/Output Input/Output 680 µF max. 220 µF max. 6‘000 VDC 3’000 VAL rms 10 pF typ. >1‘000 M ohm EN 60950 (rated for 250VAC working voltage) test report by BSI (British Standard Institute) – Operating – Case temperature – Storage –40 °C ... +85 °C +95 °C max. –40 °C ... +125 °C 5%/K 95 % rel H max. >2’000’000 h @ 25 °C 50 kHz typ. ( Frequency modulation) ± 30 % max. – Input variation – Load variation 20 – 100 % 1 Watt Output Specifications Voltage set accuracy Voltage balance ( dual output models) Regulation Ripple and noise (20 MHz Bandwidth) Temperature coefficient Short circuit protection Capacitive load Isolation /Safety Isolation voltage Isolation capacity Isolation resistance Safety standards Safety approvals General Specifications Temperature ranges Derating above 85°C Humidity (non condensing) Reliability, calculated MTBF ( MIL-HDBK-217E) Switching frequency Frequency change over line and load All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TMV-EN Series Physical Specifications Case material Package weight Soldering temperature – Single output models – Dual output models non conductive FR4 (UL 94V-0 rated) 4.0 g (0.14 oz) 4.0 g (0.14 oz) max. 265°C / 10 sec 1 Watt Outline Dimensions mm (inches) Pin-Out 10.2 (0.4) Pin 1 2 5 3.2 (0.13) 6 7 Single +Vin (Vcc) –Vin (GND) –Vout No pin +Vout Dual +Vin (Vcc) –Vin (GND) –Vout Common +Vout 0.5 (0.02) 0.5 (0.02) 2.3 ±0.4 (0.09 ±0.02) 2.54 (0.1) 7.62 (0.3) 19.5 (0.77) 2.54 2.54 (0.1) (0.1) 0.5 (0.02) 1 2 5 6 0.5 (0.02) 7 1.25 ( ) = inches Tolerances ±0.25 (0.01) pins ±0.05 (0.002) Specifications can be changed without notice Rev. 10/05 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43311 4511 · Fax +41 43311 4545 · info@traco.ch · www.tracopower.com (0.05) 6.0 (0.24) Bottom view 24 V Models 0.25 (0.01) 4.75 (0.19) 5.75 (0.23) 7.0 (0.28) Page 3 of 3