TON15-4812WI

DC/DC Converters TON 5WI Series, 5 Watt RoHS Features ◆ Smallest 5W Converter Ultra compact Size: 27.9 x 23.9 x 8.5mm compliant ◆ Ultra Wide 4: Input Voltage Range ◆ Cost efficient open Frame Design with Industry Standard Pin-out ◆ Surface-mount (SM) and Through-hole Version ◆ I/O Isolation Voltage 2250V, rated for basic Insulation ◆ Extended Operating Temperature Range: –40°C to +85°C ◆ ◆ ◆ ◆ ◆ Input Filter meets EN55022, Class A Under Voltage Lockout Remote On/Off Lead free Design, RoHS compliant 3 Years Product Warranty The TON-15WI series is a new generation of high performance 15W dc-dc converters with ultra-wide input voltage range and precisely regulated output voltage. The ultra compact open frame design with industry standard pin-out provides the designer now a 50% smaller, cost efficient alternative to existing 10 to 15W converters in the market. Built-in filters for both input and output minimize the need for external filtering. Further features include remote On/Off, output voltage trimming, over voltage protection, under voltage lockout and short circuit protection. Typical applications are distributed power systems, instrumentation and industrial electronics, everywhere where space on the PCB is a critical factor. Models Order code TON 5-240WI TON 5-24WI TON 5-242WI TON 5-243WI TON 5-480WI TON 5-48WI TON 5-482WI TON 5-483WI Add suffix SM for surface mount version 8 – 75 VDC (48 VDC nominal) 9 – 36 VDC (24 VDC nominal) Input voltage range Output voltage 3.3 VDC 5.0 VDC 12 VDC 15 VDC 3.3 VDC 5.0 VDC 12 VDC 15 VDC Output current max. 4‘000 mA 3‘000 mA 1‘300 mA 1’000 mA 4‘000 mA 3‘000 mA 1‘300 mA 1’000 mA Efficiency typ. 84 % 84 % 85 % 86 % 86 % 86 % 87 % 88 % http://www.tracopower.com Page  of 3 DC/DC Converters TON 5WI Series Input Specifications Input current at no load 24 V; 3.3/5 24 V; 12/15 24 V; 3.3/5 24 V; 12/15 Vout Vout Vout Vout models: models: models: models: models: models: models: models: 50 mA typ 20 mA typ. 40 mA typ 15 mA typ. 690 mA typ. 800 mA typ. 340 mA typ. 390 mA typ. 5 V / ms, max. (complies with ETS 300 132 part. 4.4) 24 V models: 9 VDC / 8 VDC (typ.) 48 V models: 18 VDC / 16 VDC (typ.) 24 V models: 50 V max. 48 V models: 100 V max. EN 55022 level A, FCC part 15, level A ±1% ±10 % – Input variation Vin min. to Vin max – Load variation 0 – 100 % 0.2 % max. 0.2 % max. ±0.02 % /K 3.3 / 5 Vout models: 75 mVpk-pk max. 12 / 15 Vout models: 100 mVpk-pk max. 30 ms typ. 250 µs typ. indefinite (automatic recovery) 1‘000 M Ohm 1000 pF max. 3.3 / 5 Vout models: 300 kHz typ. 12 / 15 Vout models: 400 kHz typ. – Input / Output – Input / Output – Input / Output General Specifications Temperature ranges Derating Humidity (non condensing) Reliability, calculated MTBF ( MIL-HDBK-217 F) Isolation voltage (60 sec) Isolation resistance Isolation capacity Switching frequency ( Pulse width modulation PWM) All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TON 5WI Series General Specifications Remote On/Off – On: – Off: – Off idle current: 3.0 ... 15 VDC or open circuit. 0 ... 1.2 VDC or short circuit pin 6 and pin 2 20 mA typ. 10-55Hz, 2G, 30 minutes along X,Y,Z UL 60950-1, EN 60950-1, IEC 60950-1 UL/cUL File E188913 10.5g (0.36 oz) – Trough Hole Version – SMD Version max. 265 °C / 10 sec. (wave soldering) lead-free reflow solder process as per IPC/JEDEC J-STD-020C peak temp. 245°C (20 sec. max.) 5 Watt Vibration Safety standards Safety approvals Physical Specifications Weight Soldering profile Output Voltage Adjustment Trim up Trim Trim down Ru +Vout Rd Trim - Vout Note 1 Recommended circuit to reduce conducted noise and output ripple & noise: +Vin C1 +Vout Load C1: 33µF low ESR electrolytic capacitor C2 C3 C2: 10µF low ESR electrolytic capacitor C3: 1µ film capacitor - Vin -Vout Outline Dimensions SMD Version (SM) A-A B B Trough Hole Version 7.62 (0.3) 5.08 (0.2) Pin-Out Pin 20.32 (0.80) 27.94 (1.10) 6 2 1 Single +Vin (Vcc) –Vin (GND) +Vout Trim –Vout Remote On/Off  2 3 4 5 6 5 8.5 1.3max. (0.335) (0.05) Bottom view 43 (0.15) (0.177) (0.335) (0.024) 23.88 (0.94) 0.6 Section A-A 0.5max. (0.02) Section B-B (0.030) 0.75 3.81 4.5 8.5 10.16 (0.4)10.16 (0.4) Specifications can be changed any time without notice Dimensions in [mm], () = Inch Tolerances ±0.35 (0.014) Rev. 02/07 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · info@traco.ch · www.tracopower.com Page 3 of 3