TSV2405S

DC/DC Converters TSV Series, 1 Watt Features ◆ SMD Package (SOIC-22) ◆ Isolated Single and Dual Output Models ◆ I/O-Isolation 3‘000 VDC ◆ High Efficiency up to 81% ◆ Extended Temperature Range –40°C to +85°C compliant RoHS ◆ ◆ ◆ ◆ High Accuracy of Pin Co-Planarity Available in Tape and Reel Package Lead free Design, RoHS compliant 3 Year Product Warranty The TSV series are miniature, 1W DC/DC-converters with high isolation in a SMD package. The devices can be soldered without any problems in a high temperature lead free solder process. With the small footprint, these converters are the ideal solution for board level power distribution, mainly for applications in the industrialand telecom field. Models Ordercode TSV 0505S TSV 0512S TSV 0515S TSV 0505D TSV 0512D TSV 0515D TSV 1205S TSV 1212S TSV 1215S TSV 1205D TSV 1212D TSV 1215D TSV 2405S TSV 2412S TSV 2415S TSV 2405D TSV 2412D TSV 2415D http://www.tracopower.com 24 VDC ±10% 12 VDC ±10% 5 VDC ±10% Input voltage Output voltage 5 VDC 12 VDC 15 VDC ± 5 VDC ±12 VDC ±15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ±12 VDC ±15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ±12 VDC ±15 VDC Output current max. 200 mA 80 mA 65 mA ±100 mA ± 40 mA ± 30 mA 200 mA 80 mA 65 mA ±100 mA ± 40 mA ± 30 mA 200 mA 80 mA 65 mA ±100 mA ± 40 mA ± 30 mA Efficiency typ. 71 % 78 % 78 % 72 % 78 % 79 % 71 % 79 % 80 % 74 % 80 % 81 % 71 % 78 % 79 % 72 % 79 % 80 % Page 1 of 3 DC/DC Converters TSV Series Input Specifications Input current no load /full load 5 Vin models: 30 mA / 260 mA typ. 12 Vin models: 12 mA / 110 mA typ. 24 Vin models: 7 mA / 55 mA typ. 5 Vin models: 9 V max. 12 Vin models: 18 V max. 24 Vin models: 30 V max. 0.3 A max. can be reduced by ext. 1–3.3 µF polyester film capacitor internal capacitor ±3% ± 1 % max. ± 1.2 % / 1 % change Vin ± 10 % max. 75 mV pk-pk max. ± 0.02 % / K limited 0.5 sec. max. 5 VDC single 5 VDC dual 12/15 VDC single 12/15 VDC dual – Operating – Case temperature – Storage output output output output models: models: models: models: 33 µF max. 10 µF max. 4.7 µF max. 2.2 µF max. –40 °C ... +85 °C (no derating) +95 °C max. –40 °C ... +105 °C 95 % rel H max. >2’000’000 h @ 25 °C 3‘000 VDC 60 pF typ. >10‘000 M Ohm (500VDC) 100 kHz typ. (frequency modulation) ± 30 % max. non conductive FR4 (UL 94V-0 rated) 2.2 g (0.07 oz) peak temp. 245°C (10 sec max.) 217°C for 90 sec. max. Convection reflow solder process is recommended – Input variation – Load variation 20 – 100 % 1 Watt Surge voltage (1 sec. max.) Reverse voltage protection Reflected input ripple current* Input filter Output Specifications Voltage set accuracy Voltage balance ( dual output models, balanced load) Regulation Ripple and noise (20 MHz Bandwidth) Temperature coefficient Short circuit protection Capacitive load General Specifications Temperature ranges Humidity (non condensing) Reliability, calculated MTBF ( MIL-HDBK-217F) Isolation voltage ( Input/Output) Isolation capacity ( Input/Output) Isolation resistance ( Input/Output) Switching frequency Frequency change over line and load Physical Specifications Case material Package weight Reflow soldering profile All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TSV Series Derating all Models +85˚C +105˚C 1 Watt 100 90 80 100 90 80 70 60 -5.0% / ˚ C 70 60 50 40 30 20 10 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 50 40 30 20 10 0 Ambient Temperature [˚C] Outline Dimensions 6.5 (0.256) Output Power [%] S Seating Plane Output Power [%] (0.26) 6.7 0.25 (0.18) (0.01) 4.7 10 Pins ± 4˚ 7.0 (0.27) 9.2 (0.36) 11.2 (0.44) (0.01) (0.05) 2.54 2.54 (0.1) (0.1) 5.08 (0.2) 2.54 (0.1) 0.6 (0.024) 22 20 18 14 12 0.25 1.3 0.2 M S P Pin-Out 8.0 (0.31) Pin 1 3 5 9 11 12 14 Single –Vin (GND) +Vin (Vcc) No con. –Vout No con. No con. +Vout No con. No con. No con. Dual –Vin (GND) +Vin (Vcc) No con. Common –Vout No con. +Vout No con. No con. No con. 1 3 5 15.24 (0.6) 9 11 Solder pad 1.0 (0.04) 12.7 (0.50) (0.01) 1.8 18 20 22 Dimensions in [mm], () = Inch Pin diameter: 1.0 ±0.05 (0.02 ±0.002) Pin pitch tolerances: ± 0.13 (±0.005) Case tolerances: ±0.25 (±0.01) 2.54 2.54 (0.1) (0.1) 5.08 (0.2) 2.54 (0.1) Specifications can be changed without notice Rev. 12/05.1 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · info@traco.ch · www.tracopower.com Page 3 of 3