TS8GDOM44V-S

Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Description With an IDE interface and strong data retention ability, 44-Pin IDE Flash Modules are ideal for use in the harsh environments where Industrial PCs, Set-Top Boxes, etc. are used. Features • • • • • • • • • • • RoHS compliant products Storage Capacity: 128MB ~ 8GB Operating Voltage: 3.3V ±5% or 5V ±10% Operating Temperature: 0°C ~ 70°C Endurance: 2,000,000 Program/Erase cycles MTBF: 1,000,000 hours Durability of Connector: 10,000 times Fully compatible with devices and OS that support the IDE standard (pitch = 2.00mm) Built-in ECC function assures high reliability of data transfer Supports up to Ultra DMA Mode 4 Supports PIO Mode 6 Support Wear-Leveling to extend product life Placement • Dimensions Side A B C Millimeters 52.00 ± 0.40 29.50 ± 0.50 7.20 ± 0.20 Inches 2.047 ± 0.016 1.162 ± 0.020 0.284 ± 0.008 Transcend Information Inc. 1 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Pin Assignments Pin No. Pin Name Pin No. Pin Name HD12 HD2 HD13 HD1 HD14 HD0 HD15 Pin Pin No Name 23 IOWB 24 GND 25 IORB 26 GND 27 IORDY 28 NC Pin No. Pin Name Pin Definition Symbol HD0 ~ HD15 HA0 ~ HA2 -RESET IORB IOWB IOIS16B CE1B, CE2B PDIAGB DASPB 41 42 43 44 VCC VCC GND GND DMARQ DMACKIREQ NC GND VCC Function Data Bus (Bi-directional) Address Bus (Input) Device Reset (Input) Device I/O Read (Input) Device I/O Write (Input) Transfer Type 8/16 bit (Output) Chip Select (Input) Pass Diagnostic (Bi-directional) Disk Active/Slave Present (Bi-directional) DMA request DMA acknowledge Interrupt Request (Output) No Connection Ground Vcc Power Input 01 -RESET 12 02 GND 13 03 HD7 14 04 HD8 15 05 HD6 16 06 HD9 17 07 08 09 10 11 HD5 HD10 HD4 HD11 HD3 18 34 PDIAGB 35 HA0 36 HA2 37 CE1B 38 CE2B 39 DASPB 40 GND 29 -DMAC K 19 GND 30 GND 20 NC 31 IREQ 21 DMARQ 32 IOIS16B 22 GND 33 HA1 Pin Layout Pin1 Bulge Pin43 Pin2 Pin44 Transcend Information Inc. 2 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Block Diagram With 1 pcs of Flash Memory: With 2 pcs of Flash Memory: Transcend Information Inc. 3 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Absolute Maximum Ratings Symbol VDD-VSS Ta Tst Parameter DC Power Supply Operating Temperature Storage Temperature Min -0.6 0 -40 Max +6 +70 +85 Unit V °C °C Recommended Operating Conditions Symbol VDD VIN Ta Parameter Power supply Input voltage Operating Temperature Min 3.0 0 0 Max 5.5 VDD+0.3 +70 Units V V °C DC Characteristics (Ta=0 oC to +70 oC, Vcc = 5.0V ± 10%) Parameter Supply Voltage High level output voltage Low level output voltage High level input voltage Low level input voltage Symbol VCC VOH VOL VIH VIL Min 4.5 VCC-0.8 -4.0 2.92 --- Max 5.5 -0.8 --0.8 1.70 Unit V V V V V V V Remark Non-schmitt trigger Schmitt trigger1 Non-schmitt trigger Schmitt trigger1 (Ta=0 oC to +70 oC, Vcc = 3.3V ± 5%) Parameter Supply Voltage High level output voltage Low level output voltage High level input voltage Low level input voltage Symbol VCC VOH VOL VIH VIL Min 3.135 VCC-0.8 -2.4 2.05 --- Max 3.465 -0.8 --0.6 1.25 Unit V V V V V V V Remark Non-schmitt trigger Schmitt trigger1 Non-schmitt trigger Schmitt trigger1 Transcend Information Inc. 4 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Transcend Information Inc. 5 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S True IDE PIO Mode Read/Write Timing Item Mode 0 600 70 Mode 1 383 50 Mode 2 240 30 Mode 3 180 30 Mode 4 120 25 Mode 5 100 15 Mode 6 80 10 t0 t1 t2 t2 t2i t3 t4 t5 t6 t6Z t7 t8 t9 tRD Cycle time (min) 1 Address Valid to -IORD/-IOWR setup (min) -IORD/-IOWR (min) 1 -IORD/-IOWR (min) Register (8 bit) -IORD/-IOWR recovery time (min) -IOWR data setup (min) -IOWR data hold (min) -IORD data setup (min) -IORD data hold (min) -IORD data tristate (max)2 Address valid to IOCS16 assertion (max) 4 Address valid to IOCS16 released (max) 4 -IORD/-IOWR to address valid hold Read Data Valid to IORDY active (min), if IORDY initially low after tA IORDY Setup time 3 165 290 -60 30 50 5 30 90 60 20 0 35 1250 5 125 290 -45 20 35 5 30 50 45 15 0 35 1250 5 100 290 -30 15 20 5 30 40 30 10 0 35 1250 5 80 80 70 30 10 20 5 30 N/A N/A 10 0 35 1250 5 70 70 25 20 10 20 5 30 N/A N/A 10 0 35 1250 5 65 65 25 20 5 15 5 20 N/A N/A 10 0 N/A5 N/A5 N/A5 55 55 20 15 5 10 5 20 N/A N/A 10 0 N/A5 N/A5 N/A5 tA tB IORDY Pulse Width (max) tC IORDY assertion to release (max) Notes: All timings are in nanoseconds. The maximum load on -IOCS16 is 1 LSTTL with a 50 pF (40pF below 120nsec Cycle Time) total load. All times are in nanoseconds. Minimum time from -IORDY high to -IORD high is 0 nsec, but minimum -IORD width shall still be met. (1) t0 is the minimum total cycle time, t2 is the minimum command active time, and t2i is the minimum command recovery time or command inactive time. The actual cycle time equals the sum of the actual command active time and the actual command inactive time. The three timing requirements of t0, t2, and t2i shall be met. The minimum total cycle time requirement is greater than the sum of t2 and t2i. This means a host implementation can lengthen either or both t2 or t2i to ensure that t0 is equal to or greater than the value reported in the device’s identify device data. (2) This parameter specifies the time from the negation edge of -IORD to the time that the data bus is released by the device. (3) The delay from the activation of -IORD or -IOWR until the state of IORDY is first sampled. If IORDY is inactive then the host shall wait until IORDY is active before the PIO cycle can be completed. If the device is not driving IORDY negated at tA after the activation of -IORD or -IOWR, then t5 shall be met and tRD is not applicable. If the device is driving IORDY negated at the time tA after the activation of -IORD or -IOWR, then tRD shall be met and t5 is not applicable. (4) t7 and t8 apply only to modes 0, 1 and 2. For other modes, this signal is not valid. (5) IORDY is not supported in this mode. Transcend Information Inc. 6 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S True IDE PIO Mode Timing Diagram Figure 1: True IDE PIO Mode Timing Diagram Notes: (1) Device address consists of -CS0, -CS1, and A[02::00] (2) Data consists of D[15::00] (16-bit) or D[07::00] (8 bit) (3) -IOCS16 is shown for PIO modes 0, 1 and 2. For other modes, this signal is ignored. (4) The negation of IORDY by the device is used to extend the PIO cycle. The determination of whether the cycle is to be extended is made by the host after tA from the assertion of -IORD or -IOWR. The assertion and negation of IORDY is described in the following three cases: (4-1) Device never negates IORDY: No wait is generated. (4-2) Device starts to drive IORDY low before tA, but causes IORDY to be asserted before tA: No wait generated. (4-3) Device drives IORDY low before tA: wait generated. The cycle completes after IORDY is reasserted. For cycles where a wait is generated and -IORD is asserted, the device shall place read data on D15-D00 for tRD before causing IORDY to be asserted. Transcend Information Inc. 7 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S True IDE Multiword DMA Mode Read/Write Timing Specification Item Mode 0 (ns) 480 215 150 5 100 20 0 20 50 215 120 40 50 15 20 Mode 1 (ns) 150 80 60 5 30 15 0 5 50 50 40 40 30 10 25 Mode 2 (ns) 120 70 50 5 20 10 0 5 25 25 35 35 25 10 25 Mode 3 (ns) 100 65 50 5 15 5 0 5 25 25 35 35 10 10 25 Mode 4 (ns) 80 55 45 5 10 5 0 5 20 20 35 35 5 10 25 t0 tD tE tF tG tH tI tJ tKR tKW tLR tLW tM tN tZ Notes: Cycle time (min) 1 -IORD / -IOWR asserted width(min) 1 -IORD data access (max) -IORD data hold (min) -IORD/-IOWR data setup (min) -IOWR data hold (min) DMACK to –IORD/-IOWR setup (min) -IORD / -IOWR to -DMACK hold (min) -IORD negated width (min) 1 1 -IOWR negated width (min) -IORD to DMARQ delay (max) -IOWR to DMARQ delay (max) CS(1:0) valid to –IORD / -IOWR CS(1:0) hold -DMACK (1) t0 is the minimum total cycle time and tD is the minimum command active time, while tKR and tKW are the minimum command recovery time or command inactive time for input and output cycles respectively. The actual cycle time equals the sum of the actual command active time and the actual command inactive time. The three timing requirements of t0, tD, tKR, and tKW shall be met. The minimum total cycle time requirement is greater than the sum of tD and tKR or tKW.for input and output cycles respectively. This means a host implementation can lengthen either or both of tD and either of tKR, and tKW as needed to ensure that t0 is equal to or greater than the value reported in the device’s identify device data. Transcend Information Inc. 8 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S True IDE Multiword DMA Mode Read/Write Timing Diagram Figure 2: True IDE Multiword DMA Mode Read/Write Timing Diagram Notes: (1) If the Card cannot sustain continuous, minimum cycle time DMA transfers, it may negate DMARQ within the time specified from the start of a DMA transfer cycle to suspend the DMA transfers in progress and reassert the signal at a later time to continue the DMA operation. (2) This signal may be negated by the host to suspend the DMA transfer in progress. Transcend Information Inc. 9 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Ultra DMA Mode Read/Write Timing Specification Ultra DMA is an optional data transfer protocol used with the READ DMA, and WRITE DMA, commands. When this protocol is enabled, the Ultra DMA protocol shall be used instead of the Multiword DMA protocol when these commands are issued by the host. This protocol applies to the Ultra DMA data burst only. When this protocol is used there are no changes to other elements of the ATA protocol. TRUE IDE MODE UDMA DMARQ -DMACK STOP1 -HDMARDY1,2 HSTROBE(W)1,3,4 -DDMARDY(W)1,3 DSTROBE(R)1,2,4 D[15:00] A[02:00]5 -CSEL INTRQ -CS0 -CS1 UDMA Signal DMARQ DMACK STOP HDMARDY(R) HSTROBE(W) DDMARDY(W) DSTROBE(R) DATA ADDRESS CSEL INTRQ Card Select Type Output Input Input Input Output Bidir Input input Output Input Notes: 1) The UDMA interpretation of this signal is valid only during an Ultra DMA data burst. 2) The UDMA interpretation of this signal is valid only during and Ultra DMA data burst during a DMA Read command. 3) The UDMA interpretation of this signal is valid only during an Ultra DMA data burst during a DMA Write command. 4) The HSTROBE and DSTROBE signals are active on both the rising and the falling edge. 5) Address lines 03 through 10 are not used in True IDE mode. Several signal lines are redefined to provide different functions during an Ultra DMA data burst. These lines assume their UDMA definitions when: 1. An Ultra DMA mode is selected, and 2. A host issues a READ DMA, or a WRITE DMA command requiring data transfer, and 3. The device asserts (-)DMARQ, and 4. The host asserts (-)DMACK. These signal lines revert back to the definitions used for non-Ultra DMA transfers upon the negation of -DMACK by the host at the termination of an Ultra DMA data burst. With the Ultra DMA protocol, the STROBE signal that latches data from D[15:00] is generated by the same agent (either host or device) that drives the data onto the bus. Ownership of D[15:00] and this data strobe signal are given either to the device during an Ultra DMA data-in burst or to the host for an Ultra Transcend Information Inc. 10 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S DMA data-out burst. During an Ultra DMA data burst a sender shall always drive data onto the bus, and, after a sufficient time to allow for propagation delay, cable settling, and setup time, the sender shall generate a STROBE edge to latch the data. Both edges of STROBE are used for data transfers so that the frequency of STROBE is limited to the same frequency as the data. Words in the IDENTIFY DEVICE data indicate support of the Ultra DMA feature and the Ultra DMA modes the device is capable of supporting. The Set transfer mode subcommand in the SET FEATURES command shall be used by a host to select the Ultra DMA mode at which the system operates. The Ultra DMA mode selected by a host shall be less than or equal to the fastest mode of which the device is capable. Only one Ultra DMA mode shall be selected at any given time. All timing requirements for a selected Ultra DMA mode shall be satisfied. Devices supporting any Ultra DMA mode shall also support all slower Ultra DMA modes. An Ultra DMA capable device shall retain the previously selected Ultra DMA mode after executing a software reset sequence or the sequence caused by receipt of a DEVICE RESET command if a SET FEATURES disable reverting to defaults command has been issued. The device may revert to a Multiword DMA mode if a SET FEATURES enable reverting to default has been issued. An Ultra DMA capable device shall clear any previously selected Ultra DMA mode and revert to the default non-Ultra DMA modes after executing a power-on or hardware reset. Both the host and device perform a CRC function during an Ultra DMA data burst. At the end of an Ultra DMA data burst the host sends its CRC data to the device. The device compares its CRC data to the data sent from the host. If the two values do not match, the device reports an error in the error register. If an error occurs during one or more Ultra DMA data bursts for any one command, the device shall report the first error that occurred. If the device detects that a CRC error has occurred before data transfer for the command is complete, the device may complete the transfer and report the error or abort the command and report the error. NOTE − If a data transfer is terminated before completion, the assertion of INTRQ should be passed through to the host software driver regardless of whether all data requested by the command has been transferred. Transcend Information Inc. 11 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Ultra DMA Data Burst Timing Requirements Name t2CYCTYP tCYC t2CYC tDS tDH tDVS tDVH tCS tCH tCVS tCVH tZFS tDZFS tFS tLI tMLI tUI tAZ tZAH tZAD tENV tRFS tRP tIORDYZ tZIORDY tACK tSS UDMA Mode 0 UDMA Mode 1 UDMA Mode 2 Min 240 112 230 15.0 5.0 70.0 6.2 15.0 5.0 70.0 6.2 0 70.0 0 20 0 20 0 20 160 20 0 20 50 0 20 50 Max Min 160 73 153 10.0 5.0 48.0 6.2 10.0 5.0 48.0 6.2 0 48.0 0 20 0 20 0 20 125 20 0 20 50 Max Min 120 54 115 7.0 5.0 31.0 6.2 7.0 5.0 31.0 6.2 0 31.0 0 20 0 20 0 20 100 20 0 20 50 Max UDMA Mode 3 Min 90 39 86 7.0 5.0 20.0 6.2 7.0 5.0 20.0 6.2 0 20.0 0 20 0 20 0 20 100 20 Max UDMA Mode 4 Measure location (See Note 2) Min Max 60 Sender 25 Note 3 57 Sender 5.0 Recipient 5.0 Recipient 6.7 Sender 6.2 Sender 5.0 Device 5.0 Device 6.7 Host 6.2 Host 0 Device 6.7 Sender 120 Device 0 100 Note 4 20 Host 0 Host 10 Note 5 20 Host 0 Device 20 55 Host 60 Sender 100 Recipient 20 Device 0 Device 20 Host 50 Sender 230 150 200 150 170 150 130 100 10 10 10 10 70 75 70 70 70 60 55 60 Notes: All Timings in ns (1) All timing measurement switching points (low to high and high to low) shall be taken at 1.5 V. (2) All signal transitions for a timing parameter shall be measured at the connector specified in the measurement location column. For example, in the case of tRFS, both STROBE and -DMARDY transitions are measured at the sender connector. (3) The parameter tCYC shall be measured at the recipient’s connector farthest from the sender. (4) The parameter tLI shall be measured at the connector of the sender or recipient that is responding to an incoming transition from the recipient or sender respectively. Both the incoming signal and the outgoing response shall be measured at the same connector. (5) The parameter tAZ shall be measured at the connector of the sender or recipient that is driving the bus but must release the bus to allow for a bus turnaround. (6) See Page 14 the AC Timing requirements in Ultra DMA AC Signal Requirements. Transcend Information Inc. 12 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Ultra DMA Data Burst Timing Descriptions Name t2CYCTYP tCYC t2CYC tDS tDH tDVS tDVH tCS tCH tCVS tCVH tZFS tDZFS tFS tLI tMLI tUI tAZ tZAH tZAD tENV tRFS tRP tIORDYZ tZIORDY tACK tSS Comment Notes Typical sustained average two cycle time Cycle time allowing for asymmetry and clock variations (from STROBE edge to STROBE edge) Two cycle time allowing for clock variations (from rising edge to next rising edge or from falling edge to next falling edge of STROBE) Data setup time at recipient (from data valid until STROBE edge) 2, Data hold time at recipient (from STROBE edge until data may become invalid) 2, Data valid setup time at sender (from data valid until STROBE edge) 3 Data valid hold time at sender (from STROBE edge until data may become invalid) 3 CRC word setup time at device 2 CRC word hold time device 2 CRC word valid setup time at host (from CRC valid until -DMACK negation) 3 CRC word valid hold time at sender (from -DMACK negation until CRC may become invalid) 3 Time from STROBE output released-to-driving until the first transition of critical timing. Time from data output released-to-driving until the first transition of critical timing. First STROBE time (for device to first negate DSTROBE from STOP during a data in burst) Limited interlock time 1 Interlock time with minimum 1 Unlimited interlock time 1 Maximum time allowed for output drivers to release (from asserted or negated) Minimum delay time required for output drivers to assert or negate (from released) Envelope time (from -DMACK to STOP and -HDMARDY during data in burst initiation and from DMACK to STOP during data out burst initiation) Ready-to-final-STROBE time (no STROBE edges shall be sent this long after negation of -DMARDY) Ready-to-pause time (that recipient shall wait to pause after negating -DMARDY) Maximum time before releasing IORDY Minimum time before driving IORDY 4, Setup and hold times for -DMACK (before assertion or negation) Time from STROBE edge to negation of DMARQ or assertion of STOP (when sender terminates a burst) Notes: (1) The parameters tUI, tMLI (in Page 19: Ultra DMA Data-In Burst Device Termination Timing and Page 20: Ultra DMA Data-In Burst Host Termination Timing), and tLI indicate sender-to-recipient or recipient-to-sender interlocks,i.e., one agent (either sender or recipient) is waiting for the other agent to respond with a signal before proceeding.tUI is an unlimited interlock that has no maximum time value. tMLI is a limited time-out that has a defined minimum. tLI is a limited time-out that has a defined maximum. (2) 80-conductor cabling (see see ATA specification :Annex A)) shall be required in order to meet setup (tDS, tCS) and hold (tDH, tCH) times in modes greater than 2. (3) Timing for tDVS, tDVH, tCVS and tCVH shall be met for lumped capacitive loads of 15 and 40 pF at the connector where the Data and STROBE signals have the same capacitive load value. Due to reflections on the cable, these timing measurements are not valid in a normally functioning system. (4) For all timing modes the parameter tZIORDY may be greater than tENV due to the fact that the host has a pull-up on IORDYgiving it a known state when released. Transcend Information Inc. 13 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Ultra DMA Sender and Recipient IC Timing Requirements Name UDMA Mode 0 (ns) UDMA Mode 1 (ns) UDMA Mode 2 (ns) UDMA Mode 3 (ns) UDMA Mode 4 (ns) Min Max Min 9.7 4.8 50.9 9.0 Max Min 6.8 4.8 33.9 9.0 Max Min 6.8 4.8 22.6 9.0 Max Min 4.8 4.8 9.5 9.0 Max tDSIC tDHIC tDVSIC tDVHIC tDSIC tDHIC tDVSIC tDVHIC 14.7 4.8 72.9 9.0 Recipient IC data setup time (from data valid until STROBE edge) (see note 2) Recipient IC data hold time (from STROBE edge until data may become invalid) (see note 2) Sender IC data valid setup time (from data valid until STROBE edge) (see note 3) Sender IC data valid hold time (from STROBE edge until data may become invalid) (see note 3) Notes: (1) All timing measurement switching points(low to high and high to low) shall be taken at 1.5 V. (2) The correct data value shall be captured by the recipient given input data with a slew rate of 0.4 V/ns rising and falling and the input STROBE with a slew rate of 0.4 V/ns rising and falling at tDSIC and tDHIC timing (as measured through 1.5 V). (3) The parameters tDVSIC and tDVHIC shall be met for lumped capacitive loads of 15 and 40 pF at the IC where all signals have the same capacitive load value. Noise that may couple onto the output signals from external sources has not been included in these values. Ultra DMA AC Signal Requirements Name SRISE SFALL Comment Rising Edge Slew Rate for any signal Falling Edge Slew Rate for any signal Min[V/ns] Max [V/ns] 1.25 1.25 Note 1 1 Note: (1) The sender shall be tested while driving an 18 inch long, 80 conductor cable with PVC insulation material. The signal under test shall be cut at a test point so that it has not trace, cable or recipient loading after the test point. All other signals should remain connected through to the recipient. The test point may be located at any point between the sender’s series termination resistor and one half inch or less of conductor exiting the connector. If the test point is on a cable conductor rather than the PCB, an adjacent ground conductor shall also be cut within one half inch of the connector. The test load and test points should then be soldered directly to the exposed source side connectors. The test loads consist of a 15 pF or a 40 pF, 5%, 0.08 inch by 0.05 inch surface mount or smaller size capacitor from the test point to ground. Slew rates shall be met for both capacitor values. Measurements shall be taken at the test point using a 100 Kohm, 1 Ghz or faster probe and a 500 MHz or faster oscilloscope. The average rate shall be measured from 20% to 80% of the settled VOH level with data transitions at least 120 nsec apart. The settled VOH level shall be measured as the average output high level under the defined testing conditions from 100 nsec after 80% of a rising edge until 20% of the subsequent falling edge. Transcend Information Inc. 14 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Initiating an Ultra DMA Data-In Burst (a) An Ultra DMA Data-In burst is initiated by following the steps lettered below. The timing diagram is shown in below: Ultra DMA Data-In Burst Initiation Timing. The associated timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and are described in Page 13: Ultra DMA Data Burst Timing Descriptions. (b) The following steps shall occur in the order they are listed unless otherwise specifically allowed: (c) The host shall keep -DMACK in the negated state before an Ultra DMA data burst is initiated. (d) The device shall assert DMARQ to initiate an Ultra DMA data burst. After assertion of DMARQ the device shall not negate DMARQ until after the first negation of DSTROBE. (e) Steps (c), (d), and (e) may occur in any order or at the same time. The host shall assert STOP. (f) The host shall negate -HDMARDY. (g) In True IDE mode, the host shall not assert -CS0, -CS1 and A[02:00]. (h) Steps (c), (d), and (e) shall have occurred at least tACK before the host asserts -DMACK. The host shall keep -DMACK asserted until the end of an Ultra DMA data burst. (i) The host shall release D[15:00] within tAZ after asserting -DMACK. (j) The device may assert DSTROBE tZIORDY after the host has asserted -DMACK. While operating in True IDE mode, once the device has driven DSTROBE, the device shall not release DSTROBE until after the host has negated -DMACK at the end of an Ultra DMA data burst. (k) The host shall negate STOP and assert -HDMARDY within tENV after asserting -DMACK. After negating STOP and asserting -HDMARDY, the host shall not change the state of either signal until after receiving the first transition of DSTROBE from the device (i.e., after the first data word has been received). (l) The device shall drive D[15:00] no sooner than tZAD after the host has asserted -DMACK, negated STOP, and asserted -HDMARDY. (m) The device shall drive the first word of the data transfer onto D[15:00]. This step may occur when the device first drives D[15:00] in step (j). (n) To transfer the first word of data the device shall negate DSTROBE within tFS after the host has negated STOP and asserted -HDMARDY. The device shall negate DSTROBE no sooner than tDVS after driving the first word of data onto D[15:00]. Transcend Information Inc. 15 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S ALL WAVEFORMS IN THIS DIAGRAM ARE SHOWN WITH THE ASSERTED STATE HIGH. NEGATIVE TRUE SIGNALS APPEAR INVERTED ON THE BUS RELATIVE TO THE DIAGRAM. Notes: The definitions for the IORDY:-DDMARDY:DSTROBE, -IORD: -HDMARDY:HSTROBE, and -IOWR:STOP signal lines are not in effect until DMARQ and -DMACK are asserted. A[02:00], -CS0 & -CS1 are True IDE mode signal definitions. Transcend Information Inc. 16 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Sustaining an Ultra DMA Data-In Burst An Ultra DMA Data-In burst is sustained by following the steps lettered below. The timing diagram is shown in below: Sustained Ultra DMA Data-In Burst Timing. The timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and are described in Page 13: Ultra DMA Data Burst Timing Descriptions. The following steps shall occur in the order they are listed unless otherwise specifically allowed: a) The device shall drive a data word onto D[15:00]. b) The device shall generate a DSTROBE edge to latch the new word no sooner than tDVS after changing the state of D[15:00]. The device shall generate a DSTROBE edge no more frequently than tCYC for the selected Ultra DMA mode. The device shall not generate two rising or two falling DSTROBE edges more frequently than 2tcyc for the selected Ultra DMA mode. c) The device shall not change the state of D[15:00] until at least tDVH after generating a DSTROBE edge to latch the data. d) The device shall repeat steps (a), (b), and (c) until the data transfer is complete or an Ultra DMA data burst is paused, whichever occurs first. Notes: D[15:00] and DSTROBE signals are shown at both the host and the device to emphasize that cable settling time as well as cable propagation delay shall not allow the data signals to be considered stable at the host until some time after they are driven by the device. Transcend Information Inc. 17 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Host Pausing an Ultra DMA Data-In Burst The host pauses a Data-In burst by following the steps lettered below. A timing diagram is shown in below: Ultra DMA Data-In Burst Host Pause Timing. The timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and are described in Page 13: Ultra DMA Data Burst Timing Descriptions. The following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) The host shall not pause an Ultra DMA data burst until at least one data word of an Ultra DMA data burst has been transferred. (b) The host shall pause an Ultra DMA data burst by negating -HDMARDY. (c) The device shall stop generating DSTROBE edges within tRFS of the host negating -HDMARDY. (d) While operating in Ultra DMA modes 2, 1, or 0 the host shall be prepared to receive zero, one or two additional data words after negating -HDMARDY. While operating in Ultra DMA modes 4 or 3 the host shall be prepared to receive zero, one, two or three additional data words. The additional data words are a result of cable round trip delay and tRFS timing for the device. (e) The host shall resume an Ultra DMA data burst by asserting -HDMARDY. ALL WAVEFORMS IN THIS DIAGRAM ARE SHOWN WITH THE ASSERTED STATE HIGH. NEGATIVE TRUE SIGNALS APPEAR INVERTED ON THE BUS RELATIVE TO THE DIAGRAM. Notes: (1) The host may assert STOP to request termination of the Ultra DMA data burst no sooner than tRP after -HDMARDY is negated. (2) After negating -HDMARDY, the host may receive zero, one, two, or three more data words from the device. (3) The bus polarity of the (-) DMARQ and (-)DMACK signals is dependent on the active interface mode. Transcend Information Inc. 18 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Device Terminating an Ultra DMA Data-In Burst The device terminates an Ultra DMA Data-In burst by following the steps lettered below. The timing diagram is shown in below: Ultra DMA Data-In Burst Device Termination Timing. The timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and are described in Page 13: Ultra DMA Data Burst Timing Descriptions. The following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) The device shall not pause an Ultra DMA data burst until at least one data word of an Ultra DMA data burst has been transferred. (b) The device shall pause an Ultra DMA data burst by not generating DSTROBE edges. (c) NOTE − The host shall not immediately assert STOP to initiate Ultra DMA data burst termination when the device stops generating STROBE edges. If the device does not negate DMARQ, in order to initiate Ultra DMA data burst termination, the host shall negate -HDMARDY and wait tRP before asserting STOP. (d) The device shall resume an Ultra DMA data burst by generating a DSTROBE edge. ALL WAVEFORMS IN THIS DIAGRAM ARE SHOWN WITH THE ASSERTED STATE HIGH. NEGATIVE TRUE SIGNALS APPEAR INVERTED ON THE BUS RELATIVE TO THE DIAGRAM. Notes: The definitions for the STOP, HDMARDY, and DSTROBE signal lines are no longer in effect after DMARQ and DMACK are negated. A[02:00], -CS0 & -CS1 are True IDE mode signal definitions. Transcend Information Inc. 19 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Host Terminating an Ultra DMA Data-In Burst The host terminates an Ultra DMA Data-In burst by following the steps lettered below. The timing diagram is shown in below: Ultra DMA Data-In Burst Host Termination Timing. The timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and are described in Page 13: Ultra DMA Data Burst Timing Descriptions. The following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) The host shall not initiate Ultra DMA data burst termination until at least one data word of an Ultra DMA data burst has been transferred. (b) The host shall initiate Ultra DMA data burst termination by negating -HDMARDY. The host shall continue to negate -HDMARDY until the Ultra DMA data burst is terminated. (c) The device shall stop generating DSTROBE edges within tRFS of the host negating -HDMARDY (d) While operating in Ultra DMA modes 2, 1, or 0 the host shall be prepared to receive zero, one or two additional data words after negating -HDMARDY. While operating in Ultra DMA modes 4 or 3 the host shall be prepared to receive zero, one, two or three additional data words. The additional data words are a result of cable round trip delay and tRFS timing for the device. (e) The host shall assert STOP no sooner than tRP after negating -HDMARDY. The host shall not negate STOP again until after the Ultra DMA data burst is terminated. (f) The device shall negate DMARQ within tLI after the host has asserted STOP. The device shall not assert DMARQ again until after the Ultra DMA data burst is terminated. (g) If DSTROBE is negated, the device shall assert DSTROBE within tLI after the host has asserted STOP. No data shall be transferred during this assertion. The host shall ignore this transition on DSTROBE. DSTROBE shall remain asserted until the Ultra DMA data burst is terminated. (h) The device shall release D[15:00] no later than tAZ after negating DMARQ. (i) The host shall drive D[15:00] no sooner than tZAH after the device has negated DMARQ. For this step, the host may first drive D[15:00] with the result of its CRC calculation (see ATA specification Ultra DMA CRC Calculation). (j) If the host has not placed the result of its CRC calculation on D[15:00] since first driving D[15:00] during (9), the host shall place the result of its CRC calculation on D[15:00] (see ATA specification Ultra DMA CRC Calculation). (k) The host shall negate -DMACK no sooner than tMLI after the device has asserted DSTROBE and negated DMARQ and the host has asserted STOP and negated -HDMARDY, and no sooner than tDVS after the host places the result of its CRC calculation on D[15:00]. (l) The device shall latch the host’s CRC data from D[15:00] on the negating edge of -DMACK. (m) The device shall compare the CRC data received from the host with the results of its own CRC calculation. If a miscompare error occurs during one or more Ultra DMA data burst for any one command, at the end of the command, the device shall report the first error that occurred (see ATA specification Ultra DMA CRC Calculation) (n) While operating in True IDE mode, the device shall release DSTROBE within tIORDYZ after the host negates -DMACK. (o) The host shall neither negate STOP nor assert -HDMARDY until at least tACK after the host has negated -DMACK. Transcend Information Inc. 20 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S (p) In True IDE mode, the host shall not assert -IORD, -CS0, -CS1, nor A[02:00] until at least tACK after negating DMACK. ALL WAVEFORMS IN THIS DIAGRAM ARE SHOWN WITH THE ASSERTED STATE HIGH. NEGATIVE TRUE SIGNALS APPEAR INVERTED ON THE BUS RELATIVE TO THE DIAGRAM. Notes: The definitions for the STOP, HDMARDY, and DSTROBE signal lines are no longer in effect after DMARQ and DMACK are negated. A[02:00], -CS0 & -CS1 are True IDE mode signal definitions. Transcend Information Inc. 21 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Initiating an Ultra DMA Data-Out Burst An Ultra DMA Data-out burst is initiated by following the steps lettered below. The timing diagram is shown in below: Ultra DMA Data-Out Burst Initiation Timing. The timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and are described in Page 13:Ultra DMA Data Burst Timing Descriptions. The following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) The host shall keep -DMACK in the negated state before an Ultra DMA data burst is initiated. (b) The device shall assert DMARQ to initiate an Ultra DMA data burst. (c) Steps (c), (d), and (e) may occur in any order or at the same time. The host shall assert STOP. (d) The host shall assert HSTROBE. (e) In True IDE mode, the host shall not assert -CS0, -CS1, nor A[02:00]. (f) Steps (c), (d), and (e) shall have occurred at least tACK before the host asserts -DMACK.The host shall keep -DMACK asserted until the end of an Ultra DMA data burst. (g) The device may negate -DDMARDY tZIORDY after the host has asserted -DMACK. While operating in True IDE mode, once the device has negated -DDMARDY, the device shall not release -DDMARDY until after the host has negated DMACK at the end of an Ultra DMA data burst. (h) The host shall negate STOP within tENV after asserting -DMACK. The host shall not assert STOP until after the first negation of HSTROBE. (i) The device shall assert -DDMARDY within tLI after the host has negated STOP. After asserting DMARQ and -DDMARDY the device shall not negate either signal until after the first negation of HSTROBE by the host. (j) The host shall drive the first word of the data transfer onto D[15:00]. This step may occur any time during Ultra DMA data burst initiation. (k) To transfer the first word of data: the host shall negate HSTROBE no sooner than tUI after the device has asserted -DDMARDY. The host shall negate HSTROBE no sooner than tDVS after the driving the first word of data onto D[15:00]. Transcend Information Inc. 22 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S ALL WAVEFORMS IN THIS DIAGRAM ARE SHOWN WITH THE ASSERTED STATE HIGH. NEGATIVE TRUE SIGNALS APPEAR INVERTED ON THE BUS RELATIVE TO THE DIAGRAM. Note: The definitions for the STOP, DDMARDY, and HSTROBE signal lines are not in effect until DMARQ and DMACK are asserted. A[02:00], -CS0 & -CS1 are True IDE mode signal definitions. Transcend Information Inc. 23 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Sustaining an Ultra DMA Data-Out Burst An Ultra DMA Data-Out burst is sustained by following the steps lettered below. The timing diagram is shown in below: Sustained Ultra DMA Data-Out Burst Timing. The associated timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and are described in Page 13: Ultra DMA Data Burst Timing Descriptions. The following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) The host shall drive a data word onto D[15:00]. (b) The host shall generate an HSTROBE edge to latch the new word no sooner than tDVS after changing the state of D[15:00]. The host shall generate an HSTROBE edge no more frequently than tCYC for the selected Ultra DMA mode. The host shall not generate two rising or falling HSTROBE edges more frequently than 2tcyc for the selected Ultra DMA mode. (c) The host shall not change the state of D[15:00] until at least tDVH after generating an HSTROBE edge to latch the data. (d) The host shall repeat steps (a), (b), and (c) until the data transfer is complete or an Ultra DMA data burst is paused, whichever occurs first. Note: Data (D[15:00]) and HSTROBE signals are shown at both the device and the host to emphasize that cable settling time as well as cable propagation delay shall not allow the data signals to be considered stable at the device until some time after they are driven by the host. Transcend Information Inc. 24 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Device Pausing an Ultra DMA Data-Out Burst The device pauses an Ultra DMA Data-Out burst by following the steps lettered below. The timing diagram is shown in below: Ultra DMA Data-Out Burst Device Pause Timing. The timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and are described in Page 13: Ultra DMA Data Burst Timing Descriptions. The following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) The device shall not pause an Ultra DMA data burst until at least one data word of an Ultra DMA data burst has been transferred. (b) The device shall pause an Ultra DMA data burst by negating -DDMARDY. (c) The host shall stop generating HSTROBE edges within tRFS of the device negating -DDMARDY. (d) While operating in Ultra DMA modes 2, 1, or 0 the device shall be prepared to receive zero, one or two additional data words after negating -HDMARDY. While operating in Ultra DMA modes 4 or 3 the device shall be prepared to receive zero, one, two or three additional data words. The additional data words are a result of cable round trip delay and tRFS timing for the device. (e) The device shall resume an Ultra DMA data burst by asserting -DDMARDY. ALL WAVEFORMS IN THIS DIAGRAM ARE SHOWN WITH THE ASSERTED STATE HIGH. NEGATIVE TRUE SIGNALS APPEAR INVERTED ON THE BUS RELATIVE TO THE DIAGRAM. Notes: (1) The device may negate DMARQ to request termination of the Ultra DMA data burst no sooner than tRP after -DDMARDY is negated. (2) After negating -DDMARDY, the device may receive zero, one, two, or three more data words from the host. Transcend Information Inc. 25 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Device Terminating an Ultra DMA Data-Out Burst The device terminates an Ultra DMA Data-Out burst by following the steps lettered below. The timing diagram for the operation is shown in below: Ultra DMA Data-Out Burst Device Termination Timing. The timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and are described in Page 13: Ultra DMA Data Burst Timing Descriptions. The following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) The device shall not initiate Ultra DMA data burst termination until at least one data word of an Ultra DMA data burst has been transferred. (b) The device shall initiate Ultra DMA data burst termination by negating -DDMARDY. (c) The host shall stop generating an HSTROBE edges within tRFS of the device negating -DDMARDY. (d) While operating in Ultra DMA modes 2, 1, or 0 the device shall be prepared to receive zero, one or two additional data words after negating -HDMARDY. While operating in Ultra DMA modes 4 or 3 the device shall be prepared to receive zero, one, two or three additional data words. The additional data words are a result of cable round trip delay and tRFS timing for the device. (e) The device shall negate DMARQ no sooner than tRP after negating -DDMARDY. The device shall not assert DMARQ again until after the Ultra DMA data burst is terminated. (f) The host shall assert STOP within tLI after the device has negated DMARQ. The host shall not negate STOP again until after the Ultra DMA data burst is terminated. (g) If HSTROBE is negated, the host shall assert HSTROBE within tLI after the device has negated DMARQ. No data shall be transferred during this assertion. The device shall ignore this transition of HSTROBE. HSTROBE shall remain asserted until the Ultra DMA data burst is terminated. (h) The host shall place the result of its CRC calculation on D[15:00] (see ATA specification Ultra DMA CRC Calculation). (i) The host shall negate -DMACK no sooner than tMLI after the host has asserted HSTROBE and STOP and the device has negated DMARQ and -DDMARDY, and no sooner than tDVS after placing the result of its CRC calculation on D[15:00]. (j) The device shall latch the host’s CRC data from D[15:00] on the negating edge of -DMACK. (k) The device shall compare the CRC data received from the host with the results of its own CRC calculation. If a miscompare error occurs during one or more Ultra DMA data bursts for any one command, the device shall report the first error that occurred (see ATA specification Ultra DMA CRC Calculation). (l) While operating in True IDE mode, the device shall release DSTROBE within tIORDYZ after the host negates -DMACK. (m) The host shall not negate STOP nor assert –HDMARDY until at least tACK after negating -DMACK. (n) In True IDE mode, the host shall not assert -IOWR, -CS0, -CS1, nor A[02:00] until at least tACK after negating DMACK. Transcend Information Inc. 26 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S ALL WAVEFORMS IN THIS DIAGRAM ARE SHOWN WITH THE ASSERTED STATE HIGH. NEGATIVE TRUE SIGNALS APPEAR INVERTED ON THE BUS RELATIVE TO THE DIAGRAM. Note: The definitions for the STOP, DDMARDY, and HSTROBE signal lines are no longer in effect after DMARQ and DMACK are negated. A00-A02, -CS0 & -CS1 are True IDE mode signal definitions. Transcend Information Inc. 27 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Host Terminating an Ultra DMA Data-Out Burst Termination of an Ultra DMA Data-Out burst by the host is shown in below: Ultra DMA Data-Out Burst Host Termination Timing while timing parameters are specified in Page 12: Ultra DMA Data Burst Timing Requirements and timing parameters are described in Page 13: Ultra DMA Data Burst Timing Descriptions. The following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) The host shall initiate termination of an Ultra DMA data burst by not generating HSTROBE edges. (b) The host shall assert STOP no sooner than tSS after it last generated an HSTROBE edge.The host shall not negate STOP again until after the Ultra DMA data burst is terminated. (c) The device shall negate DMARQ within tLI after the host asserts STOP. The device shall not assert DMARQ again until after the Ultra DMA data burst is terminated. (d) The device shall negate -DDMARDY within tLI after the host has negated STOP. The device shall not assert -DDMARDY again until after the Ultra DMA data burst termination is complete. (e) If HSTROBE is negated, the host shall assert HSTROBE within tLI after the device has negated DMARQ. No data shall be transferred during this assertion. The device shall ignore this transition on HSTROBE. HSTROBE shall remain asserted until the Ultra DMA data burst is terminated. (f) The host shall place the result of its CRC calculation on D[15:00] (see ATA specification Ultra DMA CRC Calculation). (g) The host shall negate -DMACK no sooner than tMLI after the host has asserted HSTROBE and STOP and the device has negated DMARQ and -DDMARDY, and no sooner than tDVS after placing the result of its CRC calculation on D[15:00]. (h) The device shall latch the host’s CRC data from D[15:00] on the negating edge of -DMACK. (i) The device shall compare the CRC data received from the host with the results of its own CRC calculation. If a miscompare error occurs during one or more Ultra DMA data bursts for any one command, at the end of the command, the device shall report the first error that occurred (see ATA specification Ultra DMA CRC Calculation). (j) While operating in True IDE mode, the device shall release -DDMARDY within tIORDYZ after the host has negated -DMACK. (k) The host shall neither negate STOP nor negate HSTROBE until at least tACK after negating -DMACK. (l) In True IDE mode, the host shall not assert -IOWR, -CS0, -CS1, nor A[02:00] until at least tACK after negating DMACK.. Transcend Information Inc. 28 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S ALL WAVEFORMS IN THIS DIAGRAM ARE SHOWN WITH THE ASSERTED STATE HIGH. NEGATIVE TRUE SIGNALS APPEAR INVERTED ON THE BUS RELATIVE TO THE DIAGRAM. Notes: The definitions for the STOP, DDMARDY, and HSTROBE signal lines are no longer in effect after DMARQ and DMACK are negated. A[02:00], -CS0 & -CS1 are True IDE mode signal definitions. Transcend Information Inc. 29 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S IDENTIFY DEVICE information The Identify Device command enables the host to receive parameter information from the device. This command has the same protocol as the Read Sector(s) command. The parameter words in the buffer have the arrangement and meanings defined in Table as below. All reserved bits or words are zero. Hosts should not depend on Obsolete words in Identify Device containing 0. Table below specifies each field in the data returned by the Identify Device Command. In Table as below, X indicates a numeric nibble value specific to the card and aaaa indicates an ASCII string specific to the particular drive. Word Address Default Value Total Bytes Data Field Type Information 0 1 2 3 4 5 6 7-8 9 10-19 20 21 22 23-26 27-46 47 48 49 50 044Ah XXXXh 0000h 00XXh 0000h 0000h XXXXh XXXXh XXXXh aaaa 0000h 0000h 0004h aaaa aaaa XXXXh 0000h XX00h 0000h 2 2 2 2 2 2 2 4 2 20 2 2 2 8 40 2 2 2 2 General configuration – Bit Significant with ATA-4 definitions. Default number of cylinders Reserved Default number of heads Obsolete Obsolete Default number of sectors per track Number of sectors per card (Word 7 = MSW, Word 8 = LSW) Obsolete Serial number in ASCII (Right Justified) Obsolete Obsolete Number of ECC bytes passed on Read/Write Long Commands Firmware revision in ASCII. Big Endian Byte Order in Word Model number in ASCII (Left Justified) Big Endian Byte Order in Word Maximum number of sectors on Read/Write Multiple command Reserved Capabilities Reserved Transcend Information Inc. 30 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Word Address Default Value Total Bytes Data Field Type Information 51 52 53 54 55 56 57-58 59 60-61 62 63 64 65 66 67 68 69-79 80-81 82-84 85-87 88 89 90 91 92-127 128 129-159 160 161 162 163 164 165-167 168-255 0200h 0000h 000Xh XXXXh XXXXh XXXXh XXXXh 01XXh XXXXh 0000h 0X0Xh 0003h XXXXh XXXXh XXXXh XXXXh 0000h 0000h XXXXh XXXXh 001Fh XXXXh XXXXh XXXXh 0000h XXXXh 0000h XXXXh 0000h 0000h XXXXh XXXXh 0000h 0000h 2 2 2 2 2 2 4 2 4 2 2 2 2 2 2 2 20 4 6 6 2 2 2 2 72 2 64 2 2 2 2 2 6 158 PIO data transfer cycle timing mode Obsolete Field Validity Current numbers of cylinders Current numbers of heads Current sectors per track Current capacity in sectors (LBAs)(Word 57 = LSW, Word 58 = MSW) Multiple sector setting Total number of sectors addressable in LBA Mode Reserved Multiword DMA transfer. In PC Card modes this value shall be 0h Advanced PIO modes supported Minimum Multiword DMA transfer cycle time per word. In PC Card modes this value shall be 0h Recommended Multiword DMA transfer cycle time. In PC Card modes this value shall be 0h Minimum PIO transfer cycle time without flow control Minimum PIO transfer cycle time with IORDY flow control Reserved Reserved – CF cards do not return an ATA version Features/command sets supported Features/command sets enabled Ultra DMA Mode Supported and Selected (UDMA mode 0 ~ 4) Time required for Security erase unit completion Time required for Enhanced security erase unit completion Current Advanced power management value Reserved Security status Vendor unique bytes Power requirement description Reserved for assignment by the CFA Key management schemes supported CF Advanced True IDE Timing Mode Capability and Setting CF Advanced PC Card I/O and Memory Timing Mode Capability Reserved for assignment by the CFA Reserved 31 Ver 1.2 Transcend Information Inc. Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Transcend Information Inc. 32 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Capacity Specifications: Transcend P/N TS128MDOM44V-S TS256MDOM44V-S TS512MDOM44V-S TS1GDOM44V-S TS2GDOM44V-S TS4GDOM44V-S TS8GDOM44V-S Capacity 128MB 256MB 512MB 1GB 2GB 4GB 8GB Cylinder (C) 248 496 993 1942 3884 7769 15538 Head (H) 16 16 16 16 16 16 16 Sector (S) 63 63 63 63 63 63 63 Transcend Information Inc. 33 Ver 1.2 Transcend 44-Piin IIDE Fllash Modulle Transcend 44-P n DE F ash Modu e TS128M ~ 8GDOM44V-S TS128M ~ 8GDOM44V-S Ordering Information TS XXXX DOM 44 V-S Transcend Product Capacity: 128M-512M = 128 MB up to 512 MB 1G-8G = 1 GB up to 8 GB IDE Flash Module (Disk On Module) Type: V = Vertical H = Horizontal Pin Count: 40 = 40 pin 44 = 44 pin The above technical information is based on industry standard data and has been tested to be reliable. However, Transcend makes no warranty, either expressed or implied, as to its accuracy and assumes no liability in connection with the use of this product. Transcend reserves the right to make changes to the specifications at any time without prior notice. USA Los Angeles: E-mail: sales@transcendusa.com Maryland: E-mail: sales_md@transcendusa.com www.transcendusa.com CHINA E-mail: sales@transcendchina.com www.transcendchina.com GERMANY E-mail: vertrieb@transcend.de www.transcend.de HONG KONG E-mail: sales@transcend.com.hk www.transcendchina.com JAPAN E-mail: sales@transcend.co.jp www.transcend.jp THE NETHERLANDS E-mail: sales@transcend.nl www.transcend.nl United Kingdom E-mail: sales@transcend-uk.com www.transcend-uk.com TAIWAN No.70, XingZhong Rd., NeiHu Dist., Taipei, Taiwan, R.O.C TEL +886-2-2792-8000 Fax +886-2-2793-2222 E-mail: sales@transcend.com.tw www.transcend.com.tw Transcend Information Inc. 34 Ver 1.2