855964

Data Sheet Features • • • • • • • For broadband access applications Usable bandwidth 10 MHz High attenuation No impedance matching required for operation at 200 Ω Balanced operation Ceramic Surface Mount Package (SMP) Small size Part Number 855964 1086 MHz SAW Filter • Package Surface Mount 3.00 x 3.00 x 1.22 mm Pin Configuration Bottom View 1 2 3 1.22 NOM. 1.32 MAX. 0.69 8 4 3.00 7 6 5 3.00 0.60 0.60 Pin No. 1 3 5 7 2,4,6,8 Description Input Balanced input Balanced output Output Case ground 1.20 0.75 Dimensions shown are nominal in millimeters All tolerances are ±0.15mm except overall length and width ±0.10mm Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 0.5 - 1.0µm, over a 2 - 6µm Ni plating Subject to change or obsolescence without notice Re v F 12-Sep-2003 Page 1 of 5 Data Sheet Operating Temperature Range: (2) -40 to +85 oC Part Number 855964 1086 MHz SAW Filter Electrical Specifications (1) Parameter (3) Center Frequency Maximum Insertion Loss 1081 - 1091 MHz 1.5 dB Bandedges Lower Bandedge Upper Bandedge Amplitude Ripple (4) 1081 - 1091 MHz Stopband Rejection (Test Fixture) 500 - 988 MHz 988 - 1002 MHz 1038 - 1046 MHz 1156 - 1600 MHz Group Delay Ripple 1081 - 1091 MHz Source Impedance (5) Load Impedance (5) Notes: 1. 2. 3. 4. 5. Minimum 1091 50 52.5 40 40 - Typical 1086 4 1076.5 1095.5 0.75 55 55 40 40 20 200 200 Maximum 5 1081 1.0 - Unit MHz dB MHz dB dB dB dB dB ns Ω Ω All specifications are based on the test circuit shown below. Testing is carried out using test fixture 971748, test data sheet 122288-02, to equipment specification 100221. In production, devices will be tested at room temperature in a Sawtek test fixture to a guardbanded specification to ensure electrical compliance over temperature. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances. Maximum peak to adjacent valley over the defined frequency range. This is the optimum impedance in order to achieve the performance shown. Test Circuit: 1 5 200Ω 3 2,4,6,8 7 200 Ω Balanced 200Ω No impedance matching required Subject to change or obsolescence without notice Re v F 12-Sep-2003 Page 2 of 5 Data Sheet Part Number 855964 1086 MHz SAW Filter Typical Performance (at +25oC) Subject to change or obsolescence without notice Re v F 12-Sep-2003 Page 3 of 5 Data Sheet Part Number 855964 1086 MHz SAW Filter Matching Schematics 1 5 200Ω 3 2,4,6,8 7 200 Ω Balanced 200Ω No impedance matching required Marking Sawtek logo Marking code PCB Footprint 1.39 .96 5 JJJYM ID dot Date code .81 3.20 SQ .23 .81 .38 The date code consists of: JJJ = Julian day, Y = last digit of year, M = manufacturing site code This footprint represents a recommendation only Dimensions shown are nominal in millimeters Tape and Reel 2.7 12.8 Ø330 Sawtek logo 4.0 0.21 2.0 Ø1.5 A 1.75 5.5 12.0 ID dot Ø102 Ø20.2 Ø13.0 2.0 1.4 Section A-A 3.25 3.25 4.0 Ø1.5 A Dimensions shown are nominal in millimeters Packaging quantity: 5000 units/reel Subject to change or obsolescence without notice Re v F 12-Sep-2003 Page 4 of 5 Data Sheet Maximum Ratings Parameter Operating Temperature Range Storage Temperature Range Part Number 855964 1086 MHz SAW Filter Symbol T Tstg Minimum -40 -40 Maximum +85 +85 Unit o o C C Warnings • • Electrostatic Sensitive Device (ESD) Avoid ultrasonic exposure Links to Additional Technical Information PCB Layout Tips S-Parameters Qualification Flowchart Soldering Profile Other Technical Information Sawtek’s liability is limited only to the Surface Acoustic Wave (SAW) component(s) described in this data sheet. Sawtek does not accept any liability for applications, processes, circuits or assemblies which are implemented using any Sawtek component described in this data sheet. Contact Information PO Box 609501 Orlando, FL 32860-9501 USA Phone: +1 (407) 886-8860 Fax: +1 (407) 886-7061 Email: custservice@sawtek.com Web: www.sawtek.com Re v F Or contact one of our worldwide network of sales offices, representatives or distributors Subject to change or obsolescence without notice 12-Sep-2003 Page 5 of 5