856066

Preliminary Data Sheet Features • • • • • • • For broadband applications Typical 3 dB bandwidth of 6.2 MHz High attenuation Single-ended operation Ceramic Surface Mount Package (SMP) Small size Replaces Sawtek P/N 851913 (BW 3dB=6.0 MHz) Part Number 856066 140 MHz SAW Filter • Package Surface Mount 13.30 x 6.50 x 1.50 mm Pin Configuration Bottom View 1 2 3 4 5 1.50 NOM. 1.65 MAX. 0.64 10 13.3 1.80 1.91 9 8 7 6 6.50 R0.51 2.31 1.02 Pin No. 5 10 1,6 2,3,4 7,8,9 Description RF output RF input Ground Case ground Case ground Dimensions shown are nominal in millimeters All tolerances are ±0.15mm except overall length and width ±0.10mm Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 0.5 - 1.0µm, over a 2 - 6µm Ni plating Subject to change or obsolescence without notice Rev A 11-Jul-2002 Page 1 of 5 Preliminary Data Sheet Operating Temperature Range: (2) 0 to +70 oC Part Number 856066 140 MHz SAW Filter Electrical Specifications (1) Parameter (3) Center Frequency Minimum Insertion Loss Lower 1 dB Bandedge (4) Upper 1 dB Bandedge Lower 3 dB Bandedge (4) Upper 3 dB Bandedge Lower 40 dB Bandedge (4) Upper 40 dB Bandedge Amplitude Variation 137.28 - 142.72 MHz Phase Linearity 137.28 - 142.72 MHz Group Delay Variation 137.28 - 142.72 MHz Absolute Delay Relative Attenuation (4) 15 - 135 MHz 145 - 350 MHz Source Impedance (5) Load Impedance (5) Substrate Material Temperature Coefficient of Frequency Notes: 1. 2. 3. 4. 5. All specifications are based on the test circuit shown below In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances All attenuation measurements are measured relative to minimum insertion loss This is the optimum impedance in order to achieve the performance shown Minimum 142.72 143 135.83 50 50 - Typical 140 23 137.1 142.9 136.9 143.1 136 144 0.5 2.0 45 1.6 60 60 50 50 LiTaO3 -23 Maximum 24.5 137.28 137 144.17 0.9 3.0 70 - Unit MHz dB MHz MHz MHz MHz MHz MHz dB deg nsec µsec dB dB Ω Ω ppm/oC Test Circuit: Actual matching values may vary due to PCB layout and parasitics 36pF 10 5 47pF 1,2,3,4,6,7,8,9 50Ω 12nH 50Ω Single-ended 50Ω 47nH Subject to change or obsolescence without notice Rev A 11-Jul-2002 Page 2 of 5 Preliminary Data Sheet Part Number 856066 140 MHz SAW Filter Typical Performance (at +25oC) Subject to change or obsolescence without notice Rev A 11-Jul-2002 Page 3 of 5 Preliminary Data Sheet Actual matching values may vary due to PCB layout and parasitics 36pF 10 5 12nH Part Number 856066 140 MHz SAW Filter Matching Schematics 50Ω Single-ended 50Ω 47nH 1,2,3,4,6,7,8,9 47pF 50Ω Marking PCB Footprint 8.84 SAWTEK 856066 XXXXXX 6.70 2.00 1.22 .69 The date code consists of: day of the current year (Julian, 3 digits), last digit of the year (1 digit) and hour (2 digits) This footprint represents a recommendation only Dimensions shown are nominal in millimeters Tape and Reel 24.8 2.7 Ø330 ID dot 0.3 2.0 4.0 Ø1.5 A 1.75 11.5 13.9 24 Ø102 Direction of travel Ø20.2 Ø13.0 2.0 2.3 Section A-A 7.1 12.0 Ø1.5 A Dimensions shown are nominal in millimeters Packaging quantity: 2000 units/reel Subject to change or obsolescence without notice Rev A 11-Jul-2002 Page 4 of 5 Preliminary Data Sheet Maximum Ratings Parameter Operating Temperature Range Storage Temperature Range Part Number 856066 140 MHz SAW Filter Symbol T Tstg Minimum 0 -40 Typical +25 - Maximum +70 +85 Unit o o C C Warnings • • Electrostatic Sensitive Device (ESD) Avoid ultrasonic exposure Links to Additional Technical Information PCB Layout Tips S-Parameters Qualification Flowchart Soldering Profile Other Technical Information Sawtek’s liability is limited only to the Surface Acoustic Wave (SAW) component(s) described in this data sheet. Sawtek does not accept any liability for applications, processes, circuits or assemblies which are implemented using any Sawtek component described in this data sheet. Contact Information PO Box 609501 Orlando, FL 32860-9501 USA Subject to change or obsolescence without notice Phone: +1 (407) 886-8860 Fax: +1 (407) 886-7061 Email: custservice@sawtek.com Web: www.sawtek.com Rev A Or contact one of our worldwide network of sales offices, representatives or distributors 11-Jul-2002 Page 5 of 5