3.0SMCJ33

3.0SMCJ SERIES Surface Mount Transient Voltage Suppressor Voltage Range 5.0 to 170 Volts 3000 Watts Peak Power Features For surface mounted application Low profile package Built-in strain relief Glass passivated junction Excellent clamping capability Fast response time: Typically less than 1.0ps from 0 volt to BV min. Typical IR less than 1μA above 10V High temperature soldering guaranteed: 260OC / 10 seconds at terminals Plastic material used carries Underwriters Laboratory Flammability Classification 94V-0 3000 watts peak pulse power capability with a 10 X 1000 us waveform by 0.01% duty cycle .129(3.27) .118(3.0) SMC/DO-214AB .245(6.22) .220(5.59) .280(7.11) .260(6.60) .012(.31) .006(.15) .103(2.62) .079(2.00) Mechanical Data Case: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Standard packaging: 16mm tape (EIA STD RS-481) Weight: 0.21gram .060(1.52) .030(0.76) .320(8.13) .305(7.75) .008(.20) .004(.10) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Type Number Peak Power Dissipation at TA=25 C, Tp=1ms (Note 1) Steady State Power Dissipation Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 2, 3) - Unidirectional Only Maximum Instantaneous Forward Voltage at 100.0A for Unidirectional Only (Note 4) Operating and Storage Temperature Range O Symbol PPK Pd IFSM VF TJ, TSTG Value Minimum 3000 5 200 3.5 / 5.0 -55 to + 150 O Units Watts Watts Amps Volts O C Notes: 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25 C Per Fig. 2. 2. Mounted on 8.0mm2 (.013mm Thick) Copper Pads to Each Terminal. 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 Pulses Per Minute Maximum. 4. VF=3.5V on 3.0SMCJ5.0 thru 3.0SMCJ90 Devices and VF=5.0V on 3.0SMCJ100 thru 3.0SMCJ170 Devices. Devices for Bipolar Applications 1. For Bidrectional Use C or CA Suffix for Types 3.0SMCJ5.0 through Types 3.0SMCJ170. 2. Electrical Characteristics Apply in Both Directions. - 612 - RATINGS AND CHARACTERISTIC CURVES (3.0SMCJ SERIES) FIG.1- PEAK PULSE POWER RATING CURVE NON-REPETITIVE PULSE WAVEFORM SHOWN in FIG. 3 TA=250C FIG.2- PULSE DERATING CURVE PEAK PULSE POWER (Pppm) or CURRENT (lpp) DERATING IN PERCENTAGE, % 100 100 Pppm, PEAK PULSE POWER, KW 75 10 50 1 25 0.31X0.31" (8.0X8.0mm) COPPER PAD AREAS 0.1 0.1 s 1.0 s 10 s 100 s 1.0ms 10ms 0 0 25 50 75 100 125 O 150 175 200 td. PULSE WIDTH, sec. TA, AMBIENT TEMPERATURE. C FIG.3- PULSE WAVEFORM 150 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 200 PEAK FORWARD SURGE CURRENT. (A) lppm, PEAK PULSE CURRENT % IRSM PULSE WIDTH (td) is DEFINED tr=10 sec. AS THE POINT WHERE THE PEAK CURRENT DECAYS to 50% of lppm 100 100 8.3ms Single Half Sine Wave JEDEC Method UNIDIRECTIONAL ONLY PEAK VALUE lppm HALF VALUE- lpp 2 50 10/1000 sec. WAVEFORM AS DEFINED BY R.E.A. 0 0 td 1.0 2.0 t, TIME, ms 3.0 4.0 10 1 10 NUMBER OF CYCLES AT 60Hz 100 FIG.5- TYPICAL JUNCTION CAPACITANCE BIDIRECTIONAL 10000 20000 FIG.6- TYPICAL JUNCTION CAPACITANCE Tj=25 0C f=1.0MHz Vsig=50mVp-p MEASURED AT ZERO BIAS Tj=25 0C f=1.0MHz Vsig=50mVp-p MEASURED AT ZERO BIAS Cj, JUNCTION CAPACITANCE, pF 1000 10000 Cj, JUNCTION CAPACITANCE, pF 1000 MEASURED AT STAND-OFF VOLTAGE,VWM 100 VR MEASURED AT STAND-OFF VOLTAGE,VWM 100 10 1 10 100 VWM, REVERSE STAND-OFF VOLTAGE. (V) 400 10 1 10 100 400 VWM, REVERSE STAND-OFF VOLTAGE. (V) - 613 - ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Device Type Modified "J" Bend Lead 3.0SMCJ5.0 3.0SMCJ5.0A 3.0SMCJ6.0 3.0SMCJ6.0A 3.0SMCJ6.5 3.0SMCJ6.5A 3.0SMCJ7.0 3.0SMCJ7.0A 3.0SMCJ7.5 3.0SMCJ7.5A 3.0SMCJ8.0 3.0SMCJ8.0A 3.0SMCJ8.5 3.0SMCJ8.5A 3.0SMCJ9.0 3.0SMCJ9.0A 3.0SMCJ10 3.0SMCJ10A 3.0SMCJ11 3.0SMCJ11A 3.0SMCJ12 3.0SMCJ12A 3.0SMCJ13 3.0SMCJ13A 3.0SMCJ14 3.0SMCJ14A 3.0SMCJ15 3.0SMCJ15A 3.0SMCJ16 3.0SMCJ16A 3.0SMCJ17 3.0SMCJ17A 3.0SMCJ18 3.0SMCJ18A 3.0SMCJ20 3.0SMCJ20A 3.0SMCJ22 3.0SMCJ22A 3.0SMCJ24 3.0SMCJ24A 3.0SMCJ26 3.0SMCJ26A 3.0SMCJ28 3.0SMCJ28A 3.0SMCJ30 3.0SMCJ30A 3.0SMCJ33 3.0SMCJ33A 3.0SMCJ36 3.0SMCJ36A 3.0SMCJ40 3.0SMCJ40A 3.0SMCJ43 3.0SMCJ43A Device Marking Code HDD HDE HDF HDG HDH HDK HDL HDM HDN HDP HDQ HDR HDS HDT HDU HDV HDW HDX HDY HDZ HED HEE HEF HEG HEH HEK HEL HEM HEN HEP HEQ HER HES HET HEU HEV HEW HEX HEY HEZ HFD HFE HFF HFG HFH HFK HFL HFM HFN HFP HFQ HFR HFS HFT Breakdown Voltage V(BR) (Volts) (Note 1) (MIN / MAX) Test Current at IT(mA) 10 10 10 10 10 10 10 10 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 Stand-off voltage VWM(Volts) 5.0 5.0 6.0 6.0 6.5 6.5 7.0 7.0 7.5 7.5 8.0 8.0 8.5 8.5 9.0 9.0 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 20 20 22 22 24 24 26 26 28 28 30 30 33 33 36 36 40 40 43 43 Maximum Reverse Leakage at V WM (Note 3) ID(uA) Maximum Peak Pulse Surge Current IPPM (Note 2) (Amps) 6.40 / 7.3 6.40 / 7.0 6.67 / 8.15 6.67 / 7.37 7.22 / 8.82 7.22 / 7.98 7.78 / 9.51 7.78 / 8.60 8.33 / 10.2 8.33 / 9.21 8.89 / 10.9 8.89 / 9.83 9.44 / 11.5 9.44 / 10.4 10.0 / 12.2 10.0 / 11.1 11.1 / 13.6 11.1 / 12.3 12.2 / 14.9 12.2 / 13.5 13.3 / 16.3 13.3 / 14.7 14.4 / 17.6 14.4 / 15.9 15.6 / 19.1 15.6 / 17.2 16.7 / 20.4 16.7 / 18.5 17.8 / 21.8 17.8 / 19.7 18.9 / 23.1 18.9 / 20.9 20.0 / 24.4 20.0 / 22.1 22.2 / 27.1 22.2 /24.5 24.4 / 29.8 24.4 / 26.9 26.7 / 32.6 26.7 / 29.5 28.9 / 35.3 28.9 / 31.9 31.1 / 38.0 31.1 / 34.4 33.3 / 40.7 33.3 / 36.8 36.7 / 44.9 36.7 / 40.6 40.0 / 48.9 40.0 / 44.2 44.4 / 54.3 44.4 / 49.1 47.8 / 58.4 47.8 / 52.8 1000 1000 1000 1000 500 500 200 200 100 100 50 50 25 25 10 10 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 312.5 326.0 263.2 291.3 243.9 267.9 225.6 250.0 209.8 232.6 200.0 220.6 188.6 208.4 177.4 194.8 159.6 176.4 149.2 164.8 136.4 150.6 126.0 139.4 116.2 129.4 111.6 123.0 104.2 115.4 98.4 106.6 93.2 102.8 83.8 92.6 74.2 84.4 69.8 77.2 64.4 71.2 60.0 66.0 56.0 62.0 50.4 56.2 46.6 51.6 42.0 46.4 39.2 43.2 Maximum Clamping Voltage at IPPM V C(Volts) 9.6 9.2 11.4 10.3 12.3 11.2 13.3 12.0 14.3 12.9 15.0 13.6 15.9 14.4 16.9 15.4 18.8 17.0 20.1 18.2 22.0 19.9 23.8 21.5 25.8 23.2 26.9 24.4 28.8 26.0 30.5 27.6 32.2 29.2 35.8 32.4 39.4 35.5 43.0 38.9 46.6 42.1 50.0 45.4 53.5 48.4 59.0 53.3 64.3 58.1 71.4 64.5 76.7 69.4 - 614 - ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Device Type Modified "J" Bend Lead 3.0SMCJ45 3.0SMCJ45A 3.0SMCJ48 3.0SMCJ48A 3.0SMCJ51 3.0SMCJ51A 3.0SMCJ54 3.0SMCJ54A 3.0SMCJ58 3.0SMCJ58A 3.0SMCJ60 3.0SMCJ60A 3.0SMCJ64 3.0SMCJ64A 3.0SMCJ70 3.0SMCJ70A 3.0SMCJ75 3.0SMCJ75A 3.0SMCJ78 3.0SMCJ78A 3.0SMCJ85 3.0SMCJ85A 3.0SMCJ90 3.0SMCJ90A 3.0SMCJ100 3.0SMCJ100A 3.0SMCJ110 3.0SMCJ110A 3.0SMCJ120 3.0SMCJ120A 3.0SMCJ130 3.0SMCJ130A 3.0SMCJ150 3.0SMCJ150A 3.0SMCJ160 3.0SMCJ160A 3.0SMCJ170 3.0SMCJ170A Device Marking Code HFU HFV HFW HFX HFY HFZ HGD HGE HGF HGG HGH HGK HGL HGM HGN HGP HGQ HGR HGS HGT HGU HGV HGW HGX HGY HGZ HHD HHE HHF HHG HHH HHK HHL HHM HHN HHP HHQ HHR Breakdown Voltage V(BR) (Volts) (Note 1) (MIN / MAX) Test Current at IT(mA) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 Stand-off voltage VWM(Volts) 45 45 48 48 51 51 54 54 58 58 60 60 64 64 70 70 75 75 78 78 85 85 90 90 100 100 110 110 120 120 130 130 150 150 160 160 170 170 Maximum Reverse Leakage at VWM (Note 3) ID(uA) Maximum Peak Pulse Surge Current IPPM (Note 2) (Amps) 50.0 / 61.1 50.0 / 55.3 53.3 / 65.1 53.3 / 58.9 56.7 / 69.3 56.7 / 62.7 60.0 / 73.3 60.0 / 66.3 64.4 / 78.7 64.4 / 71.2 66.7 / 81.5 66.7 / 73.7 71.1 / 86.9 71.1 / 78.6 77.8 / 95.1 77.8 / 86.0 83.3 / 102 83.3 / 92.1 86.7 / 106 86.7 / 95.8 94.4 / 115 94.4 / 104 100 / 122 100 / 111 111 / 136 111 / 123 122 / 149 122 / 135 133 / 163 133 / 147 144 / 176 144 / 159 167 / 204 167 / 185 178 / 218 178 / 197 189 / 231 189 / 209 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 37.4 41.2 35.0 38.8 37.0 36.4 31.2 34.4 39.2 32.0 28.0 31.0 26.4 29.2 24.0 26.6 22.4 24.8 21.6 22.8 19.8 20.8 18.8 20.6 16.8 18.6 15.4 16.8 14.0 15.6 13.0 14.4 11.2 12.4 10.4 11.6 9.8 11.0 Maximum Clamping Voltage at IPPM VC(Volts) 80.3 72.7 85.5 77.4 91.1 82.4 96.3 87.1 103 93.6 107 96.8 114 103 125 113 134 121 139 126 151 137 160 146 179 162 196 177 214 193 231 209 268 243 287 259 304 275 Notes: 1. V(BR) measured after IT applied for 300us, IT=Square wave pulse or equivalent. 2. Surge current waveform per Fig. 3 and derate per Figure 2. 3. For bidirectional types having VWM of 10 Volts and less, the ID limit is doubled 4. all terms and symbols are consistent with ANSI/IEEE C62.35 - 615 -