ES1A_1

ES1A - ES1J 1.0 AMP. Surface Mount Super Fast Rectifiers SMA/DO-214AC Features Glass passivated junction chip For surface mounted application Low profile package Built-in strain relief, Ideal for automated placement Easy pick and place Super fast recovery time for high efficiency Glass passivated chip junction High temperature soldering: 260OC/10 seconds at terminals Plastic material used carries Underwriters Laboratory Classification 94V-0 Mechanical Data Cases: Molded plastic Terminals: Pure tin plated, lead free. Polarity: Indicated by cathode band Packing: 12mm tape per EIA STD RS-481 Weight: 0.064 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 OC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol ES ES ES ES ES ES ES ES Units Type Number 1A 1B 1C 1D 1F 1G 1H 1J Maximum Recurrent Peak Reverse Voltage V VRRM 50 100 150 200 300 400 500 600 Maximum RMS Voltage V VRMS 35 70 105 140 210 280 350 420 Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current @ TA =25 C at Rated DC Blocking Voltage @ TA=100 oC Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Maximum Thermal Resistance (Note 3) Operating Temperature Range o VDC I(AV) IFSM VF IR 50 100 150 200 300 400 500 600 1.0 30 0.95 5.0 100 35 10 85 35 -55 to +150 -55 to +150 8 o V A A 1.3 1.7 V uA uA nS pF Trr Cj RθJA RθJL TJ C /W o o Storage Temperature Range TSTG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. P.C.B. Mounted on 0.2 x 0.2” (5.0 x 5.0mm) Copper Pad Area. C C - 178 - Version: B07 RATINGS AND CHARACTERISTIC CURVES (ES1A THRU ES1J) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 1.2 50 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0 FIG.2- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS AVERAGE FORWARD CURRENT. (A) 1.0 RESISTIVE OR INDUCTIVE LOAD 0.2X0.2"(5.0X5.0mm) COPPER PAD AREAS 0.8 INSTANTANEOUS FORWARD CURRENT. (A) 10 1A -D 0.4 1 0 80 90 100 110 120 o 130 140 150 0.1 LEAD TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT. (A) 30 8.3ms Single Half Sine Wave o (JEDEC Method) at TL=120 C 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 FORWARD VOLTAGE. (V) 20 25 15 10 FIG.5- TYPICAL REVERSE CHARACTERISTICS 1000 5.0 INSTANTANEOUS REVERSE CURRENT. ( A) 1 10 NUMBER OF CYCLES AT 60Hz 100 100 Tj=125 0C FIG.4- TYPICAL JUNCTION CAPACITANCE 14 12 10 8.0 6.0 4.0 2.0 0 0 1 Tj=25 0C f=1.0MHz Vsig=50mVp-p 10 Tj=85 0C JUNCTION CAPACITANCE.(pF) ES1 A- D ES 1F -J Tj=25 0C 0.1 10 100 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) REVERSE VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm ES 1H -1 J 0.2 ES 1F - 0.6 ES 1G Version: B07