FR104SG

FR101SG - FR107SG 1.0 AMP. Glass Passivated Fast Recovery Rectifiers A-405 Features G lass passivated chip junction. H igh efficiency, Low VF H igh current capability H igh reliability H igh surge current capability Low power loss M echanical Data C ases: Molded plastic E poxy: UL 94V-0 rate flame retardant Lead: Pure tin plated, Lead free., solderable per MIL-STD-202, Method 208 guaranteed P olarity: Color band denotes cathode end H igh temperature soldering guaranteed: 260 oC /10 seconds/.375”,(9.5mm) lead lengths at 5lbs., (2.3kg) tension M ounting position: Any W eight: 0.22gram Dimensions in inches and (millimeters) R ating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% M aximum Ratings and Electrical Characteristics T ype Number M aximum Recurrent Peak Reverse Voltage M aximum RMS Voltage M aximum DC Blocking Voltage M aximum Average Forward Rectified Current .375”(9.5mm) Lead Length @T A = 5 5 oC P eak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) M aximum Instantaneous Forward Voltage @ 1.0A M aximum DC Reverse Current @ TA=25 oC at Rated DC Blocking Voltage @ T A=125 oC M aximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical thermal Resistance (Note 3) O perating Temperature Range S ymbol V RRM V RMS V DC I(AV) IFSM VF IR Trr Cj R θJA TJ FR FR FR FR FR FR FR 101SG 102SG 103SG 104SG 105SG 106SG 107SG Units V V V V 50 35 50 100 70 100 200 140 200 400 280 400 1.0 600 420 600 800 560 800 1000 700 1000 30 1.3 5.0 100 150 250 15 75 -65 to +150 -65 to +150 500 A V uA uA nS pF o C /W o o S torage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A N otes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 3. Mount on Cu-Pad Size 5mm x 5mm on P.C.B. C C Version: A06 RATINGS AND CHARACTERISTIC CURVES (FR101SG THRU FR107SG) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 1.50 1000 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG AVERAGE FORWARD CURRENT. (A) 1.25 1.00 INSTANTANEOUS REVERSE CURRENT. ( A) 100 0.75 Tj=125 0C 10 Tj=75 0C 0.50 0.25 0 0 25 50 75 100 o 125 150 175 AMBIENT TEMPERATURE. ( C) 1 Tj=25 0C FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 PEAK FORWARD SURGE CURRENT. (A) 0.1 40 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 30 Tj=25 0C 20 FIG.5- TYPICAL FORWARD CHARACTERISTICS 10 8.3ms Single Half Sine Wave JEDEC Method 10 0 1 2 FIG.4- TYPICAL JUNCTION CAPACITANCE 100 INSTANTANEOUS FORWARD CURRENT. (A) 4 6 8 10 20 NUMBER OF CYCLES AT 60Hz 40 60 80 100 1.0 JUNCTION CAPACITANCE.(pF) Tj=25 0C 0.1 10 Tj=25oC Pulse Width=300 s 1% Duty Cycle 1 1 10 REVERSE VOLTAGE. (V) 100 .01 .4 .6 .8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06