FR105

FR101 - FR107 1.0 AMP. Fast Recovery Rectifiers DO-41 Features High efficiency, Low VF High current capability High reliability High surge current capability Low power loss. Mechanical Data Cases: Molded plastic Epoxy: UL 94V-0 rate flame retardant Lead: Pure tin plated, Lead free., solderable per MIL-STD-202, Method 208 guaranteed Polarity: Color band denotes cathode end High temperature soldering guaranteed: 260oC/10 seconds/.375”,(9.5mm) lead lengths at 5 lbs.,(2.3kg) tension W eight: 0.34 gram Dimensions in inches and (millimeters) Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% FR FR Symbol FR Type Number 101 102 103 Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 Maximum RMS Voltage VRMS 35 70 140 Maximum DC Blocking Voltage VDC 50 100 200 Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length @TA = 55 oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current @ TA=25 oC at Rated DC Blocking Voltage @ TA=125 oC Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance Operating Temperature Range TJ Maximum Ratings and Electrical Characteristics FR 104 FR 105 FR 106 FR 107 Units V V V A A V uA uA nS pF o 400 280 400 1.0 30 1.2 5.0 150 600 420 600 800 1000 560 700 800 1000 I(AV) IFSM VF IR Trr Cj RθJA RθJC TJ 150 Storage Temperature Range TSTG TSTG Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 3. Mount on Cu-Pad Size 5mm x 5mm on P.C.B. 250 10 65 8 -65 to +150 -65 to +150 500 C /W o o C C Version: A06 RATINGS AND CHARACTERISTIC CURVES (FR101 THRU FR107) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 1.0 1000 FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG AVERAGE FORWARD CURRENT. (A) INSTANTANEOUS REVERSE CURRENT. ( A) 0.75 100 Tj=125 0C 0.5 0.25 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length 0 25 50 75 100 o 10 Tj=75 0C 0 125 150 175 AMBIENT TEMPERATURE. ( C) 1.0 Tj=25 0C FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 PEAK FORWARD SURGE CURRENT. (A) 0.1 40 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 30 8.3ms Single Half Sine Wave JEDEC Method 20 FIG.5- TYPICAL FORWARD CHARACTERISTICS 10 20 10 0 1 2 4 6 8 10 20 NUMBER OF CYCLES AT 60Hz 40 60 80 100 Tj=25oC Pulse Width=300 s 1% Duty Cycle INSTANTANEOUS FORWARD CURRENT. (A) 3.0 FIG.4- TYPICAL JUNCTION CAPACITANCE 90 1.0 JUNCTION CAPACITANCE.(pF) 50 0.3 30 20 Tj=25 C 0 0.1 10 0.03 1 1 0.01 2 4 6 10 20 40 60 100 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 REVERSE VOLTAGE. (V) FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE +0.5A DUT (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr (+) 50Vdc (approx) (-) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06