FR1603G

FR1601G THRU FR1607G 16.0 AMPS. Glass Passivated Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 16.0 Amperes Features Low forward voltage drop High current capability High reliability High surge current capability TO-220 Mechanical Data Cases: TO-220 molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Leads solderable per MIL-STD-202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260℃/10 seconds .16”,(4.06mm) from case. Mounting position: Any Weight: 2.24 grams PIN 1 PIN 3 Positive CT CASE PIN 2 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% FR Symbol FR Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 2 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 8.0A Maximum DC Reverse Current @ TC=25℃ at Rated DC Blocking Voltage @ TC=125℃ Maximum Reverse Recovery Time ( Note 1) Typical Thermal Resistance (Note 2) FR FR FR FR FR 1601G 1602G 1603G 1604G 1605G 1606G 1607G Units V V V A A V uA uA nS ℃/W ℃ VRRM VRMS VDC I(AV) IFSM VF IR 50 35 50 100 70 100 200 140 200 400 280 400 16.0 150 1.3 5.0 100 600 420 600 800 1000 560 700 800 1000 250 500 3.0 Operating and Storage Temperature Range TJ ,TSTG -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink size 2” x 3” x 0.25” Al-Plate RθJC Trr 150 - 468 - RATINGS AND CHARACTERISTIC CURVES (FR1601G THRU FR1607G) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm AVERAGE FORWARD CURRENT. (A) 20.0 16.0 12.0 8.0 4.0 0 FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.3- TYPICAL REVERSE CHARACTERISTICS PER LEG 1000 INSTANTANEOUS REVERSE CURRENT. ( A) 100 Tj=125 0C 10 0 50 CASE TEMPERATURE. ( C) o 100 150 Tj=25 0C 1.0 PEAK FORWARD SURGE CURRENT. (A) 300 250 200 150 100 50 0 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 8.3ms Single Half Sine Wave JEDEC Method 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.6- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 80 1 2 5 10 20 50 100 INSTANTANEOUS FORWARD CURRENT. (A) 40 20 10 NUMBER OF CYCLES AT 60Hz FIG.5- TYPICAL JUNCTION CAPACITANCE PER LEG 300 250 4 2 1.0 CAPACITANCE.(pF) 200 150 100 50 0 Tj=25 0C f=1.0MHz Vsig=50mVp-p 0.1 0.5 1.0 5 10 50 100 500 1000 .4 .2 .1 .8 Tj=25oC Pulse Width=300 s 1% Duty Cycle .9 1.0 1.1 1.2 1.3 1.4 1.5 REVERSE VOLTAGE. (V) INSTANTANEOUS FORWARD VOLTAGE. (V) - 469 -